ath9k: merge noisefloor load implementations
AR5008+ and AR9003 currently use two separate implementations of the
ath9k_hw_loadnf function. There are three main differences:
- PHY registers for AR9003 are different
- AR9003 always uses 3 chains, earlier versions are more selective
- The AR9003 variant contains a fix for NF load timeouts
This patch merges the two implementations into one, storing the
register array in the ath_hw struct. The fix for NF load timeouts is
not just relevant for AR9003, but also important for earlier hardware,
so it's better to just keep one common implementation.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
diff --git a/drivers/net/wireless/ath/ath9k/calib.c b/drivers/net/wireless/ath/ath9k/calib.c
index cc29ef7..7f4c55f 100644
--- a/drivers/net/wireless/ath/ath9k/calib.c
+++ b/drivers/net/wireless/ath/ath9k/calib.c
@@ -167,6 +167,100 @@
REG_SET_BIT(ah, AR_PHY_AGC_CONTROL, AR_PHY_AGC_CONTROL_NF);
}
+void ath9k_hw_loadnf(struct ath_hw *ah, struct ath9k_channel *chan)
+{
+ struct ath9k_nfcal_hist *h;
+ unsigned i, j;
+ int32_t val;
+ u8 chainmask;
+ struct ath_common *common = ath9k_hw_common(ah);
+
+ if (AR_SREV_9300_20_OR_LATER(ah))
+ chainmask = 0x3F;
+ else if (AR_SREV_9285(ah) || AR_SREV_9271(ah))
+ chainmask = 0x9;
+ else if (AR_SREV_9280(ah) || AR_SREV_9287(ah)) {
+ if ((ah->rxchainmask & 0x2) || (ah->rxchainmask & 0x4))
+ chainmask = 0x1B;
+ else
+ chainmask = 0x09;
+ } else {
+ if (ah->rxchainmask & 0x4)
+ chainmask = 0x3F;
+ else if (ah->rxchainmask & 0x2)
+ chainmask = 0x1B;
+ else
+ chainmask = 0x09;
+ }
+ h = ah->nfCalHist;
+
+ for (i = 0; i < NUM_NF_READINGS; i++) {
+ if (chainmask & (1 << i)) {
+ val = REG_READ(ah, ah->nf_regs[i]);
+ val &= 0xFFFFFE00;
+ val |= (((u32) (h[i].privNF) << 1) & 0x1ff);
+ REG_WRITE(ah, ah->nf_regs[i], val);
+ }
+ }
+
+ /*
+ * Load software filtered NF value into baseband internal minCCApwr
+ * variable.
+ */
+ REG_CLR_BIT(ah, AR_PHY_AGC_CONTROL,
+ AR_PHY_AGC_CONTROL_ENABLE_NF);
+ REG_CLR_BIT(ah, AR_PHY_AGC_CONTROL,
+ AR_PHY_AGC_CONTROL_NO_UPDATE_NF);
+ REG_SET_BIT(ah, AR_PHY_AGC_CONTROL, AR_PHY_AGC_CONTROL_NF);
+
+ /*
+ * Wait for load to complete, should be fast, a few 10s of us.
+ * The max delay was changed from an original 250us to 10000us
+ * since 250us often results in NF load timeout and causes deaf
+ * condition during stress testing 12/12/2009
+ */
+ for (j = 0; j < 1000; j++) {
+ if ((REG_READ(ah, AR_PHY_AGC_CONTROL) &
+ AR_PHY_AGC_CONTROL_NF) == 0)
+ break;
+ udelay(10);
+ }
+
+ /*
+ * We timed out waiting for the noisefloor to load, probably due to an
+ * in-progress rx. Simply return here and allow the load plenty of time
+ * to complete before the next calibration interval. We need to avoid
+ * trying to load -50 (which happens below) while the previous load is
+ * still in progress as this can cause rx deafness. Instead by returning
+ * here, the baseband nf cal will just be capped by our present
+ * noisefloor until the next calibration timer.
+ */
+ if (j == 1000) {
+ ath_print(common, ATH_DBG_ANY, "Timeout while waiting for nf "
+ "to load: AR_PHY_AGC_CONTROL=0x%x\n",
+ REG_READ(ah, AR_PHY_AGC_CONTROL));
+ return;
+ }
+
+ /*
+ * Restore maxCCAPower register parameter again so that we're not capped
+ * by the median we just loaded. This will be initial (and max) value
+ * of next noise floor calibration the baseband does.
+ */
+ ENABLE_REGWRITE_BUFFER(ah);
+ for (i = 0; i < NUM_NF_READINGS; i++) {
+ if (chainmask & (1 << i)) {
+ val = REG_READ(ah, ah->nf_regs[i]);
+ val &= 0xFFFFFE00;
+ val |= (((u32) (-50) << 1) & 0x1ff);
+ REG_WRITE(ah, ah->nf_regs[i], val);
+ }
+ }
+ REGWRITE_BUFFER_FLUSH(ah);
+ DISABLE_REGWRITE_BUFFER(ah);
+}
+
+
static void ath9k_hw_nf_sanitize(struct ath_hw *ah, s16 *nf)
{
struct ath_common *common = ath9k_hw_common(ah);