[media] Add support for M-5MOLS 8 Mega Pixel camera ISP
Add I2C/V4L2 subdev driver for M-5MOLS integrated image signal processor
with 8 Mega Pixel sensor.
Signed-off-by: HeungJun, Kim <riverful.kim@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
diff --git a/drivers/media/video/Kconfig b/drivers/media/video/Kconfig
index 3be180b..47bfd32 100644
--- a/drivers/media/video/Kconfig
+++ b/drivers/media/video/Kconfig
@@ -757,6 +757,8 @@
---help---
This driver supports NOON010PC30 CIF camera from Siliconfile
+source "drivers/media/video/m5mols/Kconfig"
+
config VIDEO_OMAP3
tristate "OMAP 3 Camera support (EXPERIMENTAL)"
select OMAP_IOMMU
diff --git a/drivers/media/video/Makefile b/drivers/media/video/Makefile
index 9519160..f0fecd6 100644
--- a/drivers/media/video/Makefile
+++ b/drivers/media/video/Makefile
@@ -69,6 +69,7 @@
obj-$(CONFIG_VIDEO_MT9V032) += mt9v032.o
obj-$(CONFIG_VIDEO_SR030PC30) += sr030pc30.o
obj-$(CONFIG_VIDEO_NOON010PC30) += noon010pc30.o
+obj-$(CONFIG_VIDEO_M5MOLS) += m5mols/
obj-$(CONFIG_SOC_CAMERA_IMX074) += imx074.o
obj-$(CONFIG_SOC_CAMERA_MT9M001) += mt9m001.o
diff --git a/drivers/media/video/m5mols/Kconfig b/drivers/media/video/m5mols/Kconfig
new file mode 100644
index 0000000..302dc3d
--- /dev/null
+++ b/drivers/media/video/m5mols/Kconfig
@@ -0,0 +1,5 @@
+config VIDEO_M5MOLS
+ tristate "Fujitsu M-5MOLS 8MP sensor support"
+ depends on I2C && VIDEO_V4L2 && VIDEO_V4L2_SUBDEV_API
+ ---help---
+ This driver supports Fujitsu M-5MOLS camera sensor with ISP
diff --git a/drivers/media/video/m5mols/Makefile b/drivers/media/video/m5mols/Makefile
new file mode 100644
index 0000000..0a44e02
--- /dev/null
+++ b/drivers/media/video/m5mols/Makefile
@@ -0,0 +1,3 @@
+m5mols-objs := m5mols_core.o m5mols_controls.o m5mols_capture.o
+
+obj-$(CONFIG_VIDEO_M5MOLS) += m5mols.o
diff --git a/drivers/media/video/m5mols/m5mols.h b/drivers/media/video/m5mols/m5mols.h
new file mode 100644
index 0000000..10b55c8
--- /dev/null
+++ b/drivers/media/video/m5mols/m5mols.h
@@ -0,0 +1,296 @@
+/*
+ * Header for M-5MOLS 8M Pixel camera sensor with ISP
+ *
+ * Copyright (C) 2011 Samsung Electronics Co., Ltd.
+ * Author: HeungJun Kim, riverful.kim@samsung.com
+ *
+ * Copyright (C) 2009 Samsung Electronics Co., Ltd.
+ * Author: Dongsoo Nathaniel Kim, dongsoo45.kim@samsung.com
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#ifndef M5MOLS_H
+#define M5MOLS_H
+
+#include <media/v4l2-subdev.h>
+#include "m5mols_reg.h"
+
+extern int m5mols_debug;
+
+#define to_m5mols(__sd) container_of(__sd, struct m5mols_info, sd)
+
+#define to_sd(__ctrl) \
+ (&container_of(__ctrl->handler, struct m5mols_info, handle)->sd)
+
+enum m5mols_restype {
+ M5MOLS_RESTYPE_MONITOR,
+ M5MOLS_RESTYPE_CAPTURE,
+ M5MOLS_RESTYPE_MAX,
+};
+
+/**
+ * struct m5mols_resolution - structure for the resolution
+ * @type: resolution type according to the pixel code
+ * @width: width of the resolution
+ * @height: height of the resolution
+ * @reg: resolution preset register value
+ */
+struct m5mols_resolution {
+ u8 reg;
+ enum m5mols_restype type;
+ u16 width;
+ u16 height;
+};
+
+/**
+ * struct m5mols_exif - structure for the EXIF information of M-5MOLS
+ * @exposure_time: exposure time register value
+ * @shutter_speed: speed of the shutter register value
+ * @aperture: aperture register value
+ * @exposure_bias: it calls also EV bias
+ * @iso_speed: ISO register value
+ * @flash: status register value of the flash
+ * @sdr: status register value of the Subject Distance Range
+ * @qval: not written exact meaning in document
+ */
+struct m5mols_exif {
+ u32 exposure_time;
+ u32 shutter_speed;
+ u32 aperture;
+ u32 brightness;
+ u32 exposure_bias;
+ u16 iso_speed;
+ u16 flash;
+ u16 sdr;
+ u16 qval;
+};
+
+/**
+ * struct m5mols_capture - Structure for the capture capability
+ * @exif: EXIF information
+ * @main: size in bytes of the main image
+ * @thumb: size in bytes of the thumb image, if it was accompanied
+ * @total: total size in bytes of the produced image
+ */
+struct m5mols_capture {
+ struct m5mols_exif exif;
+ u32 main;
+ u32 thumb;
+ u32 total;
+};
+
+/**
+ * struct m5mols_scenemode - structure for the scenemode capability
+ * @metering: metering light register value
+ * @ev_bias: EV bias register value
+ * @wb_mode: mode which means the WhiteBalance is Auto or Manual
+ * @wb_preset: whitebalance preset register value in the Manual mode
+ * @chroma_en: register value whether the Chroma capability is enabled or not
+ * @chroma_lvl: chroma's level register value
+ * @edge_en: register value Whether the Edge capability is enabled or not
+ * @edge_lvl: edge's level register value
+ * @af_range: Auto Focus's range
+ * @fd_mode: Face Detection mode
+ * @mcc: Multi-axis Color Conversion which means emotion color
+ * @light: status of the Light
+ * @flash: status of the Flash
+ * @tone: Tone color which means Contrast
+ * @iso: ISO register value
+ * @capt_mode: Mode of the Image Stabilization while the camera capturing
+ * @wdr: Wide Dynamic Range register value
+ *
+ * The each value according to each scenemode is recommended in the documents.
+ */
+struct m5mols_scenemode {
+ u32 metering;
+ u32 ev_bias;
+ u32 wb_mode;
+ u32 wb_preset;
+ u32 chroma_en;
+ u32 chroma_lvl;
+ u32 edge_en;
+ u32 edge_lvl;
+ u32 af_range;
+ u32 fd_mode;
+ u32 mcc;
+ u32 light;
+ u32 flash;
+ u32 tone;
+ u32 iso;
+ u32 capt_mode;
+ u32 wdr;
+};
+
+/**
+ * struct m5mols_version - firmware version information
+ * @customer: customer information
+ * @project: version of project information according to customer
+ * @fw: firmware revision
+ * @hw: hardware revision
+ * @param: version of the parameter
+ * @awb: Auto WhiteBalance algorithm version
+ * @str: information about manufacturer and packaging vendor
+ * @af: Auto Focus version
+ *
+ * The register offset starts the customer version at 0x0, and it ends
+ * the awb version at 0x09. The customer, project information occupies 1 bytes
+ * each. And also the fw, hw, param, awb each requires 2 bytes. The str is
+ * unique string associated with firmware's version. It includes information
+ * about manufacturer and the vendor of the sensor's packaging. The least
+ * significant 2 bytes of the string indicate packaging manufacturer.
+ */
+#define VERSION_STRING_SIZE 22
+struct m5mols_version {
+ u8 customer;
+ u8 project;
+ u16 fw;
+ u16 hw;
+ u16 param;
+ u16 awb;
+ u8 str[VERSION_STRING_SIZE];
+ u8 af;
+};
+#define VERSION_SIZE sizeof(struct m5mols_version)
+
+/**
+ * struct m5mols_info - M-5MOLS driver data structure
+ * @pdata: platform data
+ * @sd: v4l-subdev instance
+ * @pad: media pad
+ * @ffmt: current fmt according to resolution type
+ * @res_type: current resolution type
+ * @code: current code
+ * @irq_waitq: waitqueue for the capture
+ * @work_irq: workqueue for the IRQ
+ * @flags: state variable for the interrupt handler
+ * @handle: control handler
+ * @autoexposure: Auto Exposure control
+ * @exposure: Exposure control
+ * @autowb: Auto White Balance control
+ * @colorfx: Color effect control
+ * @saturation: Saturation control
+ * @zoom: Zoom control
+ * @ver: information of the version
+ * @cap: the capture mode attributes
+ * @power: current sensor's power status
+ * @ctrl_sync: true means all controls of the sensor are initialized
+ * @int_capture: true means the capture interrupt is issued once
+ * @lock_ae: true means the Auto Exposure is locked
+ * @lock_awb: true means the Aut WhiteBalance is locked
+ * @resolution: register value for current resolution
+ * @interrupt: register value for current interrupt status
+ * @mode: register value for current operation mode
+ * @mode_save: register value for current operation mode for saving
+ * @set_power: optional power callback to the board code
+ */
+struct m5mols_info {
+ const struct m5mols_platform_data *pdata;
+ struct v4l2_subdev sd;
+ struct media_pad pad;
+ struct v4l2_mbus_framefmt ffmt[M5MOLS_RESTYPE_MAX];
+ int res_type;
+ enum v4l2_mbus_pixelcode code;
+ wait_queue_head_t irq_waitq;
+ struct work_struct work_irq;
+ unsigned long flags;
+
+ struct v4l2_ctrl_handler handle;
+ /* Autoexposure/exposure control cluster */
+ struct {
+ struct v4l2_ctrl *autoexposure;
+ struct v4l2_ctrl *exposure;
+ };
+ struct v4l2_ctrl *autowb;
+ struct v4l2_ctrl *colorfx;
+ struct v4l2_ctrl *saturation;
+ struct v4l2_ctrl *zoom;
+
+ struct m5mols_version ver;
+ struct m5mols_capture cap;
+ bool power;
+ bool ctrl_sync;
+ bool lock_ae;
+ bool lock_awb;
+ u8 resolution;
+ u32 interrupt;
+ u32 mode;
+ u32 mode_save;
+ int (*set_power)(struct device *dev, int on);
+};
+
+#define ST_CAPT_IRQ 0
+
+#define is_powered(__info) (__info->power)
+#define is_ctrl_synced(__info) (__info->ctrl_sync)
+#define is_available_af(__info) (__info->ver.af)
+#define is_code(__code, __type) (__code == m5mols_default_ffmt[__type].code)
+#define is_manufacturer(__info, __manufacturer) \
+ (__info->ver.str[0] == __manufacturer[0] && \
+ __info->ver.str[1] == __manufacturer[1])
+/*
+ * I2C operation of the M-5MOLS
+ *
+ * The I2C read operation of the M-5MOLS requires 2 messages. The first
+ * message sends the information about the command, command category, and total
+ * message size. The second message is used to retrieve the data specifed in
+ * the first message
+ *
+ * 1st message 2nd message
+ * +-------+---+----------+-----+-------+ +------+------+------+------+
+ * | size1 | R | category | cmd | size2 | | d[0] | d[1] | d[2] | d[3] |
+ * +-------+---+----------+-----+-------+ +------+------+------+------+
+ * - size1: message data size(5 in this case)
+ * - size2: desired buffer size of the 2nd message
+ * - d[0..3]: according to size2
+ *
+ * The I2C write operation needs just one message. The message includes
+ * category, command, total size, and desired data.
+ *
+ * 1st message
+ * +-------+---+----------+-----+------+------+------+------+
+ * | size1 | W | category | cmd | d[0] | d[1] | d[2] | d[3] |
+ * +-------+---+----------+-----+------+------+------+------+
+ * - d[0..3]: according to size1
+ */
+int m5mols_read(struct v4l2_subdev *sd, u32 reg_comb, u32 *val);
+int m5mols_write(struct v4l2_subdev *sd, u32 reg_comb, u32 val);
+int m5mols_busy(struct v4l2_subdev *sd, u8 category, u8 cmd, u32 value);
+
+/*
+ * Mode operation of the M-5MOLS
+ *
+ * Changing the mode of the M-5MOLS is needed right executing order.
+ * There are three modes(PARAMETER, MONITOR, CAPTURE) which can be changed
+ * by user. There are various categories associated with each mode.
+ *
+ * +============================================================+
+ * | mode | category |
+ * +============================================================+
+ * | FLASH | FLASH(only after Stand-by or Power-on) |
+ * | SYSTEM | SYSTEM(only after sensor arm-booting) |
+ * | PARAMETER | PARAMETER |
+ * | MONITOR | MONITOR(preview), Auto Focus, Face Detection |
+ * | CAPTURE | Single CAPTURE, Preview(recording) |
+ * +============================================================+
+ *
+ * The available executing order between each modes are as follows:
+ * PARAMETER <---> MONITOR <---> CAPTURE
+ */
+int m5mols_mode(struct m5mols_info *info, u32 mode);
+
+int m5mols_enable_interrupt(struct v4l2_subdev *sd, u32 reg);
+int m5mols_sync_controls(struct m5mols_info *info);
+int m5mols_start_capture(struct m5mols_info *info);
+int m5mols_do_scenemode(struct m5mols_info *info, u32 mode);
+int m5mols_lock_3a(struct m5mols_info *info, bool lock);
+int m5mols_set_ctrl(struct v4l2_ctrl *ctrl);
+
+/* The firmware function */
+int m5mols_update_fw(struct v4l2_subdev *sd,
+ int (*set_power)(struct m5mols_info *, bool));
+
+#endif /* M5MOLS_H */
diff --git a/drivers/media/video/m5mols/m5mols_capture.c b/drivers/media/video/m5mols/m5mols_capture.c
new file mode 100644
index 0000000..d71a390
--- /dev/null
+++ b/drivers/media/video/m5mols/m5mols_capture.c
@@ -0,0 +1,191 @@
+/*
+ * The Capture code for Fujitsu M-5MOLS ISP
+ *
+ * Copyright (C) 2011 Samsung Electronics Co., Ltd.
+ * Author: HeungJun Kim, riverful.kim@samsung.com
+ *
+ * Copyright (C) 2009 Samsung Electronics Co., Ltd.
+ * Author: Dongsoo Nathaniel Kim, dongsoo45.kim@samsung.com
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#include <linux/i2c.h>
+#include <linux/slab.h>
+#include <linux/irq.h>
+#include <linux/interrupt.h>
+#include <linux/delay.h>
+#include <linux/version.h>
+#include <linux/gpio.h>
+#include <linux/regulator/consumer.h>
+#include <linux/videodev2.h>
+#include <linux/version.h>
+#include <media/v4l2-ctrls.h>
+#include <media/v4l2-device.h>
+#include <media/v4l2-subdev.h>
+#include <media/m5mols.h>
+
+#include "m5mols.h"
+#include "m5mols_reg.h"
+
+static int m5mols_capture_error_handler(struct m5mols_info *info,
+ int timeout)
+{
+ int ret;
+
+ /* Disable all interrupts and clear relevant interrupt staus bits */
+ ret = m5mols_write(&info->sd, SYSTEM_INT_ENABLE,
+ info->interrupt & ~(REG_INT_CAPTURE));
+ if (ret)
+ return ret;
+
+ if (timeout == 0)
+ return -ETIMEDOUT;
+
+ return 0;
+}
+/**
+ * m5mols_read_rational - I2C read of a rational number
+ *
+ * Read numerator and denominator from registers @addr_num and @addr_den
+ * respectively and return the division result in @val.
+ */
+static int m5mols_read_rational(struct v4l2_subdev *sd, u32 addr_num,
+ u32 addr_den, u32 *val)
+{
+ u32 num, den;
+
+ int ret = m5mols_read(sd, addr_num, &num);
+ if (!ret)
+ ret = m5mols_read(sd, addr_den, &den);
+ if (ret)
+ return ret;
+ *val = den == 0 ? 0 : num / den;
+ return ret;
+}
+
+/**
+ * m5mols_capture_info - Gather captured image information
+ *
+ * For now it gathers only EXIF information and file size.
+ */
+static int m5mols_capture_info(struct m5mols_info *info)
+{
+ struct m5mols_exif *exif = &info->cap.exif;
+ struct v4l2_subdev *sd = &info->sd;
+ int ret;
+
+ ret = m5mols_read_rational(sd, EXIF_INFO_EXPTIME_NU,
+ EXIF_INFO_EXPTIME_DE, &exif->exposure_time);
+ if (ret)
+ return ret;
+ ret = m5mols_read_rational(sd, EXIF_INFO_TV_NU, EXIF_INFO_TV_DE,
+ &exif->shutter_speed);
+ if (ret)
+ return ret;
+ ret = m5mols_read_rational(sd, EXIF_INFO_AV_NU, EXIF_INFO_AV_DE,
+ &exif->aperture);
+ if (ret)
+ return ret;
+ ret = m5mols_read_rational(sd, EXIF_INFO_BV_NU, EXIF_INFO_BV_DE,
+ &exif->brightness);
+ if (ret)
+ return ret;
+ ret = m5mols_read_rational(sd, EXIF_INFO_EBV_NU, EXIF_INFO_EBV_DE,
+ &exif->exposure_bias);
+ if (ret)
+ return ret;
+
+ ret = m5mols_read(sd, EXIF_INFO_ISO, (u32 *)&exif->iso_speed);
+ if (!ret)
+ ret = m5mols_read(sd, EXIF_INFO_FLASH, (u32 *)&exif->flash);
+ if (!ret)
+ ret = m5mols_read(sd, EXIF_INFO_SDR, (u32 *)&exif->sdr);
+ if (!ret)
+ ret = m5mols_read(sd, EXIF_INFO_QVAL, (u32 *)&exif->qval);
+ if (ret)
+ return ret;
+
+ if (!ret)
+ ret = m5mols_read(sd, CAPC_IMAGE_SIZE, &info->cap.main);
+ if (!ret)
+ ret = m5mols_read(sd, CAPC_THUMB_SIZE, &info->cap.thumb);
+ if (!ret)
+ info->cap.total = info->cap.main + info->cap.thumb;
+
+ return ret;
+}
+
+int m5mols_start_capture(struct m5mols_info *info)
+{
+ struct v4l2_subdev *sd = &info->sd;
+ u32 resolution = info->resolution;
+ int timeout;
+ int ret;
+
+ /*
+ * Preparing capture. Setting control & interrupt before entering
+ * capture mode
+ *
+ * 1) change to MONITOR mode for operating control & interrupt
+ * 2) set controls (considering v4l2_control value & lock 3A)
+ * 3) set interrupt
+ * 4) change to CAPTURE mode
+ */
+ ret = m5mols_mode(info, REG_MONITOR);
+ if (!ret)
+ ret = m5mols_sync_controls(info);
+ if (!ret)
+ ret = m5mols_lock_3a(info, true);
+ if (!ret)
+ ret = m5mols_enable_interrupt(sd, REG_INT_CAPTURE);
+ if (!ret)
+ ret = m5mols_mode(info, REG_CAPTURE);
+ if (!ret) {
+ /* Wait for capture interrupt, after changing capture mode */
+ timeout = wait_event_interruptible_timeout(info->irq_waitq,
+ test_bit(ST_CAPT_IRQ, &info->flags),
+ msecs_to_jiffies(2000));
+ if (test_and_clear_bit(ST_CAPT_IRQ, &info->flags))
+ ret = m5mols_capture_error_handler(info, timeout);
+ }
+ if (!ret)
+ ret = m5mols_lock_3a(info, false);
+ if (ret)
+ return ret;
+ /*
+ * Starting capture. Setting capture frame count and resolution and
+ * the format(available format: JPEG, Bayer RAW, YUV).
+ *
+ * 1) select single or multi(enable to 25), format, size
+ * 2) set interrupt
+ * 3) start capture(for main image, now)
+ * 4) get information
+ * 5) notify file size to v4l2 device(e.g, to s5p-fimc v4l2 device)
+ */
+ ret = m5mols_write(sd, CAPC_SEL_FRAME, 1);
+ if (!ret)
+ ret = m5mols_write(sd, CAPP_YUVOUT_MAIN, REG_JPEG);
+ if (!ret)
+ ret = m5mols_write(sd, CAPP_MAIN_IMAGE_SIZE, resolution);
+ if (!ret)
+ ret = m5mols_enable_interrupt(sd, REG_INT_CAPTURE);
+ if (!ret)
+ ret = m5mols_write(sd, CAPC_START, REG_CAP_START_MAIN);
+ if (!ret) {
+ /* Wait for the capture completion interrupt */
+ timeout = wait_event_interruptible_timeout(info->irq_waitq,
+ test_bit(ST_CAPT_IRQ, &info->flags),
+ msecs_to_jiffies(2000));
+ if (test_and_clear_bit(ST_CAPT_IRQ, &info->flags)) {
+ ret = m5mols_capture_info(info);
+ if (!ret)
+ v4l2_subdev_notify(sd, 0, &info->cap.total);
+ }
+ }
+
+ return m5mols_capture_error_handler(info, timeout);
+}
diff --git a/drivers/media/video/m5mols/m5mols_controls.c b/drivers/media/video/m5mols/m5mols_controls.c
new file mode 100644
index 0000000..817c16f
--- /dev/null
+++ b/drivers/media/video/m5mols/m5mols_controls.c
@@ -0,0 +1,299 @@
+/*
+ * Controls for M-5MOLS 8M Pixel camera sensor with ISP
+ *
+ * Copyright (C) 2011 Samsung Electronics Co., Ltd.
+ * Author: HeungJun Kim, riverful.kim@samsung.com
+ *
+ * Copyright (C) 2009 Samsung Electronics Co., Ltd.
+ * Author: Dongsoo Nathaniel Kim, dongsoo45.kim@samsung.com
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#include <linux/i2c.h>
+#include <linux/delay.h>
+#include <linux/videodev2.h>
+#include <media/v4l2-ctrls.h>
+
+#include "m5mols.h"
+#include "m5mols_reg.h"
+
+static struct m5mols_scenemode m5mols_default_scenemode[] = {
+ [REG_SCENE_NORMAL] = {
+ REG_AE_CENTER, REG_AE_INDEX_00, REG_AWB_AUTO, 0,
+ REG_CHROMA_ON, 3, REG_EDGE_ON, 5,
+ REG_AF_NORMAL, REG_FD_OFF,
+ REG_MCC_NORMAL, REG_LIGHT_OFF, REG_FLASH_OFF,
+ 5, REG_ISO_AUTO, REG_CAP_NONE, REG_WDR_OFF,
+ },
+ [REG_SCENE_PORTRAIT] = {
+ REG_AE_CENTER, REG_AE_INDEX_00, REG_AWB_AUTO, 0,
+ REG_CHROMA_ON, 3, REG_EDGE_ON, 4,
+ REG_AF_NORMAL, BIT_FD_EN | BIT_FD_DRAW_FACE_FRAME,
+ REG_MCC_OFF, REG_LIGHT_OFF, REG_FLASH_OFF,
+ 6, REG_ISO_AUTO, REG_CAP_NONE, REG_WDR_OFF,
+ },
+ [REG_SCENE_LANDSCAPE] = {
+ REG_AE_ALL, REG_AE_INDEX_00, REG_AWB_AUTO, 0,
+ REG_CHROMA_ON, 4, REG_EDGE_ON, 6,
+ REG_AF_NORMAL, REG_FD_OFF,
+ REG_MCC_OFF, REG_LIGHT_OFF, REG_FLASH_OFF,
+ 6, REG_ISO_AUTO, REG_CAP_NONE, REG_WDR_OFF,
+ },
+ [REG_SCENE_SPORTS] = {
+ REG_AE_CENTER, REG_AE_INDEX_00, REG_AWB_AUTO, 0,
+ REG_CHROMA_ON, 3, REG_EDGE_ON, 5,
+ REG_AF_NORMAL, REG_FD_OFF,
+ REG_MCC_OFF, REG_LIGHT_OFF, REG_FLASH_OFF,
+ 6, REG_ISO_AUTO, REG_CAP_NONE, REG_WDR_OFF,
+ },
+ [REG_SCENE_PARTY_INDOOR] = {
+ REG_AE_CENTER, REG_AE_INDEX_00, REG_AWB_AUTO, 0,
+ REG_CHROMA_ON, 4, REG_EDGE_ON, 5,
+ REG_AF_NORMAL, REG_FD_OFF,
+ REG_MCC_OFF, REG_LIGHT_OFF, REG_FLASH_OFF,
+ 6, REG_ISO_200, REG_CAP_NONE, REG_WDR_OFF,
+ },
+ [REG_SCENE_BEACH_SNOW] = {
+ REG_AE_CENTER, REG_AE_INDEX_10_POS, REG_AWB_AUTO, 0,
+ REG_CHROMA_ON, 4, REG_EDGE_ON, 5,
+ REG_AF_NORMAL, REG_FD_OFF,
+ REG_MCC_OFF, REG_LIGHT_OFF, REG_FLASH_OFF,
+ 6, REG_ISO_50, REG_CAP_NONE, REG_WDR_OFF,
+ },
+ [REG_SCENE_SUNSET] = {
+ REG_AE_CENTER, REG_AE_INDEX_00, REG_AWB_PRESET,
+ REG_AWB_DAYLIGHT,
+ REG_CHROMA_ON, 3, REG_EDGE_ON, 5,
+ REG_AF_NORMAL, REG_FD_OFF,
+ REG_MCC_OFF, REG_LIGHT_OFF, REG_FLASH_OFF,
+ 6, REG_ISO_AUTO, REG_CAP_NONE, REG_WDR_OFF,
+ },
+ [REG_SCENE_DAWN_DUSK] = {
+ REG_AE_CENTER, REG_AE_INDEX_00, REG_AWB_PRESET,
+ REG_AWB_FLUORESCENT_1,
+ REG_CHROMA_ON, 3, REG_EDGE_ON, 5,
+ REG_AF_NORMAL, REG_FD_OFF,
+ REG_MCC_OFF, REG_LIGHT_OFF, REG_FLASH_OFF,
+ 6, REG_ISO_AUTO, REG_CAP_NONE, REG_WDR_OFF,
+ },
+ [REG_SCENE_FALL] = {
+ REG_AE_CENTER, REG_AE_INDEX_00, REG_AWB_AUTO, 0,
+ REG_CHROMA_ON, 5, REG_EDGE_ON, 5,
+ REG_AF_NORMAL, REG_FD_OFF,
+ REG_MCC_OFF, REG_LIGHT_OFF, REG_FLASH_OFF,
+ 6, REG_ISO_AUTO, REG_CAP_NONE, REG_WDR_OFF,
+ },
+ [REG_SCENE_NIGHT] = {
+ REG_AE_CENTER, REG_AE_INDEX_00, REG_AWB_AUTO, 0,
+ REG_CHROMA_ON, 3, REG_EDGE_ON, 5,
+ REG_AF_NORMAL, REG_FD_OFF,
+ REG_MCC_OFF, REG_LIGHT_OFF, REG_FLASH_OFF,
+ 6, REG_ISO_AUTO, REG_CAP_NONE, REG_WDR_OFF,
+ },
+ [REG_SCENE_AGAINST_LIGHT] = {
+ REG_AE_CENTER, REG_AE_INDEX_00, REG_AWB_AUTO, 0,
+ REG_CHROMA_ON, 3, REG_EDGE_ON, 5,
+ REG_AF_NORMAL, REG_FD_OFF,
+ REG_MCC_OFF, REG_LIGHT_OFF, REG_FLASH_OFF,
+ 6, REG_ISO_AUTO, REG_CAP_NONE, REG_WDR_OFF,
+ },
+ [REG_SCENE_FIRE] = {
+ REG_AE_CENTER, REG_AE_INDEX_00, REG_AWB_AUTO, 0,
+ REG_CHROMA_ON, 3, REG_EDGE_ON, 5,
+ REG_AF_NORMAL, REG_FD_OFF,
+ REG_MCC_OFF, REG_LIGHT_OFF, REG_FLASH_OFF,
+ 6, REG_ISO_50, REG_CAP_NONE, REG_WDR_OFF,
+ },
+ [REG_SCENE_TEXT] = {
+ REG_AE_CENTER, REG_AE_INDEX_00, REG_AWB_AUTO, 0,
+ REG_CHROMA_ON, 3, REG_EDGE_ON, 7,
+ REG_AF_MACRO, REG_FD_OFF,
+ REG_MCC_OFF, REG_LIGHT_OFF, REG_FLASH_OFF,
+ 6, REG_ISO_AUTO, REG_CAP_ANTI_SHAKE, REG_WDR_ON,
+ },
+ [REG_SCENE_CANDLE] = {
+ REG_AE_CENTER, REG_AE_INDEX_00, REG_AWB_AUTO, 0,
+ REG_CHROMA_ON, 3, REG_EDGE_ON, 5,
+ REG_AF_NORMAL, REG_FD_OFF,
+ REG_MCC_OFF, REG_LIGHT_OFF, REG_FLASH_OFF,
+ 6, REG_ISO_AUTO, REG_CAP_NONE, REG_WDR_OFF,
+ },
+};
+
+/**
+ * m5mols_do_scenemode() - Change current scenemode
+ * @mode: Desired mode of the scenemode
+ *
+ * WARNING: The execution order is important. Do not change the order.
+ */
+int m5mols_do_scenemode(struct m5mols_info *info, u32 mode)
+{
+ struct v4l2_subdev *sd = &info->sd;
+ struct m5mols_scenemode scenemode = m5mols_default_scenemode[mode];
+ int ret;
+
+ if (mode > REG_SCENE_CANDLE)
+ return -EINVAL;
+
+ ret = m5mols_lock_3a(info, false);
+ if (!ret)
+ ret = m5mols_write(sd, AE_EV_PRESET_MONITOR, mode);
+ if (!ret)
+ ret = m5mols_write(sd, AE_EV_PRESET_CAPTURE, mode);
+ if (!ret)
+ ret = m5mols_write(sd, AE_MODE, scenemode.metering);
+ if (!ret)
+ ret = m5mols_write(sd, AE_INDEX, scenemode.ev_bias);
+ if (!ret)
+ ret = m5mols_write(sd, AWB_MODE, scenemode.wb_mode);
+ if (!ret)
+ ret = m5mols_write(sd, AWB_MANUAL, scenemode.wb_preset);
+ if (!ret)
+ ret = m5mols_write(sd, MON_CHROMA_EN, scenemode.chroma_en);
+ if (!ret)
+ ret = m5mols_write(sd, MON_CHROMA_LVL, scenemode.chroma_lvl);
+ if (!ret)
+ ret = m5mols_write(sd, MON_EDGE_EN, scenemode.edge_en);
+ if (!ret)
+ ret = m5mols_write(sd, MON_EDGE_LVL, scenemode.edge_lvl);
+ if (!ret && is_available_af(info))
+ ret = m5mols_write(sd, AF_MODE, scenemode.af_range);
+ if (!ret && is_available_af(info))
+ ret = m5mols_write(sd, FD_CTL, scenemode.fd_mode);
+ if (!ret)
+ ret = m5mols_write(sd, MON_TONE_CTL, scenemode.tone);
+ if (!ret)
+ ret = m5mols_write(sd, AE_ISO, scenemode.iso);
+ if (!ret)
+ ret = m5mols_mode(info, REG_CAPTURE);
+ if (!ret)
+ ret = m5mols_write(sd, CAPP_WDR_EN, scenemode.wdr);
+ if (!ret)
+ ret = m5mols_write(sd, CAPP_MCC_MODE, scenemode.mcc);
+ if (!ret)
+ ret = m5mols_write(sd, CAPP_LIGHT_CTRL, scenemode.light);
+ if (!ret)
+ ret = m5mols_write(sd, CAPP_FLASH_CTRL, scenemode.flash);
+ if (!ret)
+ ret = m5mols_write(sd, CAPC_MODE, scenemode.capt_mode);
+ if (!ret)
+ ret = m5mols_mode(info, REG_MONITOR);
+
+ return ret;
+}
+
+static int m5mols_lock_ae(struct m5mols_info *info, bool lock)
+{
+ int ret = 0;
+
+ if (info->lock_ae != lock)
+ ret = m5mols_write(&info->sd, AE_LOCK,
+ lock ? REG_AE_LOCK : REG_AE_UNLOCK);
+ if (!ret)
+ info->lock_ae = lock;
+
+ return ret;
+}
+
+static int m5mols_lock_awb(struct m5mols_info *info, bool lock)
+{
+ int ret = 0;
+
+ if (info->lock_awb != lock)
+ ret = m5mols_write(&info->sd, AWB_LOCK,
+ lock ? REG_AWB_LOCK : REG_AWB_UNLOCK);
+ if (!ret)
+ info->lock_awb = lock;
+
+ return ret;
+}
+
+/* m5mols_lock_3a() - Lock 3A(Auto Exposure, Auto Whitebalance, Auto Focus) */
+int m5mols_lock_3a(struct m5mols_info *info, bool lock)
+{
+ int ret;
+
+ ret = m5mols_lock_ae(info, lock);
+ if (!ret)
+ ret = m5mols_lock_awb(info, lock);
+ /* Don't need to handle unlocking AF */
+ if (!ret && is_available_af(info) && lock)
+ ret = m5mols_write(&info->sd, AF_EXECUTE, REG_AF_STOP);
+
+ return ret;
+}
+
+/* m5mols_set_ctrl() - The main s_ctrl function called by m5mols_set_ctrl() */
+int m5mols_set_ctrl(struct v4l2_ctrl *ctrl)
+{
+ struct v4l2_subdev *sd = to_sd(ctrl);
+ struct m5mols_info *info = to_m5mols(sd);
+ int ret;
+
+ switch (ctrl->id) {
+ case V4L2_CID_ZOOM_ABSOLUTE:
+ return m5mols_write(sd, MON_ZOOM, ctrl->val);
+
+ case V4L2_CID_EXPOSURE_AUTO:
+ ret = m5mols_lock_ae(info,
+ ctrl->val == V4L2_EXPOSURE_AUTO ? false : true);
+ if (!ret && ctrl->val == V4L2_EXPOSURE_AUTO)
+ ret = m5mols_write(sd, AE_MODE, REG_AE_ALL);
+ if (!ret && ctrl->val == V4L2_EXPOSURE_MANUAL) {
+ int val = info->exposure->val;
+ ret = m5mols_write(sd, AE_MODE, REG_AE_OFF);
+ if (!ret)
+ ret = m5mols_write(sd, AE_MAN_GAIN_MON, val);
+ if (!ret)
+ ret = m5mols_write(sd, AE_MAN_GAIN_CAP, val);
+ }
+ return ret;
+
+ case V4L2_CID_AUTO_WHITE_BALANCE:
+ ret = m5mols_lock_awb(info, ctrl->val ? false : true);
+ if (!ret)
+ ret = m5mols_write(sd, AWB_MODE, ctrl->val ?
+ REG_AWB_AUTO : REG_AWB_PRESET);
+ return ret;
+
+ case V4L2_CID_SATURATION:
+ ret = m5mols_write(sd, MON_CHROMA_LVL, ctrl->val);
+ if (!ret)
+ ret = m5mols_write(sd, MON_CHROMA_EN, REG_CHROMA_ON);
+ return ret;
+
+ case V4L2_CID_COLORFX:
+ /*
+ * This control uses two kinds of registers: normal & color.
+ * The normal effect belongs to category 1, while the color
+ * one belongs to category 2.
+ *
+ * The normal effect uses one register: CAT1_EFFECT.
+ * The color effect uses three registers:
+ * CAT2_COLOR_EFFECT, CAT2_CFIXR, CAT2_CFIXB.
+ */
+ ret = m5mols_write(sd, PARM_EFFECT,
+ ctrl->val == V4L2_COLORFX_NEGATIVE ? REG_EFFECT_NEGA :
+ ctrl->val == V4L2_COLORFX_EMBOSS ? REG_EFFECT_EMBOSS :
+ REG_EFFECT_OFF);
+ if (!ret)
+ ret = m5mols_write(sd, MON_EFFECT,
+ ctrl->val == V4L2_COLORFX_SEPIA ?
+ REG_COLOR_EFFECT_ON : REG_COLOR_EFFECT_OFF);
+ if (!ret)
+ ret = m5mols_write(sd, MON_CFIXR,
+ ctrl->val == V4L2_COLORFX_SEPIA ?
+ REG_CFIXR_SEPIA : 0);
+ if (!ret)
+ ret = m5mols_write(sd, MON_CFIXB,
+ ctrl->val == V4L2_COLORFX_SEPIA ?
+ REG_CFIXB_SEPIA : 0);
+ return ret;
+ }
+
+ return -EINVAL;
+}
diff --git a/drivers/media/video/m5mols/m5mols_core.c b/drivers/media/video/m5mols/m5mols_core.c
new file mode 100644
index 0000000..76eac26
--- /dev/null
+++ b/drivers/media/video/m5mols/m5mols_core.c
@@ -0,0 +1,1004 @@
+/*
+ * Driver for M-5MOLS 8M Pixel camera sensor with ISP
+ *
+ * Copyright (C) 2011 Samsung Electronics Co., Ltd.
+ * Author: HeungJun Kim, riverful.kim@samsung.com
+ *
+ * Copyright (C) 2009 Samsung Electronics Co., Ltd.
+ * Author: Dongsoo Nathaniel Kim, dongsoo45.kim@samsung.com
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#include <linux/i2c.h>
+#include <linux/slab.h>
+#include <linux/irq.h>
+#include <linux/interrupt.h>
+#include <linux/delay.h>
+#include <linux/version.h>
+#include <linux/gpio.h>
+#include <linux/regulator/consumer.h>
+#include <linux/videodev2.h>
+#include <media/v4l2-ctrls.h>
+#include <media/v4l2-device.h>
+#include <media/v4l2-subdev.h>
+#include <media/m5mols.h>
+
+#include "m5mols.h"
+#include "m5mols_reg.h"
+
+int m5mols_debug;
+module_param(m5mols_debug, int, 0644);
+
+#define MODULE_NAME "M5MOLS"
+#define M5MOLS_I2C_CHECK_RETRY 500
+
+/* The regulator consumer names for external voltage regulators */
+static struct regulator_bulk_data supplies[] = {
+ {
+ .supply = "core", /* ARM core power, 1.2V */
+ }, {
+ .supply = "dig_18", /* digital power 1, 1.8V */
+ }, {
+ .supply = "d_sensor", /* sensor power 1, 1.8V */
+ }, {
+ .supply = "dig_28", /* digital power 2, 2.8V */
+ }, {
+ .supply = "a_sensor", /* analog power */
+ }, {
+ .supply = "dig_12", /* digital power 3, 1.2V */
+ },
+};
+
+static struct v4l2_mbus_framefmt m5mols_default_ffmt[M5MOLS_RESTYPE_MAX] = {
+ [M5MOLS_RESTYPE_MONITOR] = {
+ .width = 1920,
+ .height = 1080,
+ .code = V4L2_MBUS_FMT_VYUY8_2X8,
+ .field = V4L2_FIELD_NONE,
+ .colorspace = V4L2_COLORSPACE_JPEG,
+ },
+ [M5MOLS_RESTYPE_CAPTURE] = {
+ .width = 1920,
+ .height = 1080,
+ .code = V4L2_MBUS_FMT_JPEG_1X8,
+ .field = V4L2_FIELD_NONE,
+ .colorspace = V4L2_COLORSPACE_JPEG,
+ },
+};
+#define SIZE_DEFAULT_FFMT ARRAY_SIZE(m5mols_default_ffmt)
+
+static const struct m5mols_resolution m5mols_reg_res[] = {
+ { 0x01, M5MOLS_RESTYPE_MONITOR, 128, 96 }, /* SUB-QCIF */
+ { 0x03, M5MOLS_RESTYPE_MONITOR, 160, 120 }, /* QQVGA */
+ { 0x05, M5MOLS_RESTYPE_MONITOR, 176, 144 }, /* QCIF */
+ { 0x06, M5MOLS_RESTYPE_MONITOR, 176, 176 },
+ { 0x08, M5MOLS_RESTYPE_MONITOR, 240, 320 }, /* QVGA */
+ { 0x09, M5MOLS_RESTYPE_MONITOR, 320, 240 }, /* QVGA */
+ { 0x0c, M5MOLS_RESTYPE_MONITOR, 240, 400 }, /* WQVGA */
+ { 0x0d, M5MOLS_RESTYPE_MONITOR, 400, 240 }, /* WQVGA */
+ { 0x0e, M5MOLS_RESTYPE_MONITOR, 352, 288 }, /* CIF */
+ { 0x13, M5MOLS_RESTYPE_MONITOR, 480, 360 },
+ { 0x15, M5MOLS_RESTYPE_MONITOR, 640, 360 }, /* qHD */
+ { 0x17, M5MOLS_RESTYPE_MONITOR, 640, 480 }, /* VGA */
+ { 0x18, M5MOLS_RESTYPE_MONITOR, 720, 480 },
+ { 0x1a, M5MOLS_RESTYPE_MONITOR, 800, 480 }, /* WVGA */
+ { 0x1f, M5MOLS_RESTYPE_MONITOR, 800, 600 }, /* SVGA */
+ { 0x21, M5MOLS_RESTYPE_MONITOR, 1280, 720 }, /* HD */
+ { 0x25, M5MOLS_RESTYPE_MONITOR, 1920, 1080 }, /* 1080p */
+ { 0x29, M5MOLS_RESTYPE_MONITOR, 3264, 2448 }, /* 2.63fps 8M */
+ { 0x39, M5MOLS_RESTYPE_MONITOR, 800, 602 }, /* AHS_MON debug */
+
+ { 0x02, M5MOLS_RESTYPE_CAPTURE, 320, 240 }, /* QVGA */
+ { 0x04, M5MOLS_RESTYPE_CAPTURE, 400, 240 }, /* WQVGA */
+ { 0x07, M5MOLS_RESTYPE_CAPTURE, 480, 360 },
+ { 0x08, M5MOLS_RESTYPE_CAPTURE, 640, 360 }, /* qHD */
+ { 0x09, M5MOLS_RESTYPE_CAPTURE, 640, 480 }, /* VGA */
+ { 0x0a, M5MOLS_RESTYPE_CAPTURE, 800, 480 }, /* WVGA */
+ { 0x10, M5MOLS_RESTYPE_CAPTURE, 1280, 720 }, /* HD */
+ { 0x14, M5MOLS_RESTYPE_CAPTURE, 1280, 960 }, /* 1M */
+ { 0x17, M5MOLS_RESTYPE_CAPTURE, 1600, 1200 }, /* 2M */
+ { 0x19, M5MOLS_RESTYPE_CAPTURE, 1920, 1080 }, /* Full-HD */
+ { 0x1a, M5MOLS_RESTYPE_CAPTURE, 2048, 1152 }, /* 3Mega */
+ { 0x1b, M5MOLS_RESTYPE_CAPTURE, 2048, 1536 },
+ { 0x1c, M5MOLS_RESTYPE_CAPTURE, 2560, 1440 }, /* 4Mega */
+ { 0x1d, M5MOLS_RESTYPE_CAPTURE, 2560, 1536 },
+ { 0x1f, M5MOLS_RESTYPE_CAPTURE, 2560, 1920 }, /* 5Mega */
+ { 0x21, M5MOLS_RESTYPE_CAPTURE, 3264, 1836 }, /* 6Mega */
+ { 0x22, M5MOLS_RESTYPE_CAPTURE, 3264, 1960 },
+ { 0x25, M5MOLS_RESTYPE_CAPTURE, 3264, 2448 }, /* 8Mega */
+};
+
+/**
+ * m5mols_swap_byte - an byte array to integer conversion function
+ * @size: size in bytes of I2C packet defined in the M-5MOLS datasheet
+ *
+ * Convert I2C data byte array with performing any required byte
+ * reordering to assure proper values for each data type, regardless
+ * of the architecture endianness.
+ */
+static u32 m5mols_swap_byte(u8 *data, u8 length)
+{
+ if (length == 1)
+ return *data;
+ else if (length == 2)
+ return be16_to_cpu(*((u16 *)data));
+ else
+ return be32_to_cpu(*((u32 *)data));
+}
+
+/**
+ * m5mols_read - I2C read function
+ * @reg: combination of size, category and command for the I2C packet
+ * @val: read value
+ */
+int m5mols_read(struct v4l2_subdev *sd, u32 reg, u32 *val)
+{
+ struct i2c_client *client = v4l2_get_subdevdata(sd);
+ u8 rbuf[M5MOLS_I2C_MAX_SIZE + 1];
+ u8 size = I2C_SIZE(reg);
+ u8 category = I2C_CATEGORY(reg);
+ u8 cmd = I2C_COMMAND(reg);
+ struct i2c_msg msg[2];
+ u8 wbuf[5];
+ int ret;
+
+ if (!client->adapter)
+ return -ENODEV;
+
+ if (size != 1 && size != 2 && size != 4) {
+ v4l2_err(sd, "Wrong data size\n");
+ return -EINVAL;
+ }
+
+ msg[0].addr = client->addr;
+ msg[0].flags = 0;
+ msg[0].len = 5;
+ msg[0].buf = wbuf;
+ wbuf[0] = 5;
+ wbuf[1] = M5MOLS_BYTE_READ;
+ wbuf[2] = category;
+ wbuf[3] = cmd;
+ wbuf[4] = size;
+
+ msg[1].addr = client->addr;
+ msg[1].flags = I2C_M_RD;
+ msg[1].len = size + 1;
+ msg[1].buf = rbuf;
+
+ /* minimum stabilization time */
+ usleep_range(200, 200);
+
+ ret = i2c_transfer(client->adapter, msg, 2);
+ if (ret < 0) {
+ v4l2_err(sd, "read failed: size:%d cat:%02x cmd:%02x. %d\n",
+ size, category, cmd, ret);
+ return ret;
+ }
+
+ *val = m5mols_swap_byte(&rbuf[1], size);
+
+ return 0;
+}
+
+/**
+ * m5mols_write - I2C command write function
+ * @reg: combination of size, category and command for the I2C packet
+ * @val: value to write
+ */
+int m5mols_write(struct v4l2_subdev *sd, u32 reg, u32 val)
+{
+ struct i2c_client *client = v4l2_get_subdevdata(sd);
+ u8 wbuf[M5MOLS_I2C_MAX_SIZE + 4];
+ u8 category = I2C_CATEGORY(reg);
+ u8 cmd = I2C_COMMAND(reg);
+ u8 size = I2C_SIZE(reg);
+ u32 *buf = (u32 *)&wbuf[4];
+ struct i2c_msg msg[1];
+ int ret;
+
+ if (!client->adapter)
+ return -ENODEV;
+
+ if (size != 1 && size != 2 && size != 4) {
+ v4l2_err(sd, "Wrong data size\n");
+ return -EINVAL;
+ }
+
+ msg->addr = client->addr;
+ msg->flags = 0;
+ msg->len = (u16)size + 4;
+ msg->buf = wbuf;
+ wbuf[0] = size + 4;
+ wbuf[1] = M5MOLS_BYTE_WRITE;
+ wbuf[2] = category;
+ wbuf[3] = cmd;
+
+ *buf = m5mols_swap_byte((u8 *)&val, size);
+
+ usleep_range(200, 200);
+
+ ret = i2c_transfer(client->adapter, msg, 1);
+ if (ret < 0) {
+ v4l2_err(sd, "write failed: size:%d cat:%02x cmd:%02x. %d\n",
+ size, category, cmd, ret);
+ return ret;
+ }
+
+ return 0;
+}
+
+int m5mols_busy(struct v4l2_subdev *sd, u8 category, u8 cmd, u32 mask)
+{
+ u32 busy, i;
+ int ret;
+
+ for (i = 0; i < M5MOLS_I2C_CHECK_RETRY; i++) {
+ ret = m5mols_read(sd, I2C_REG(category, cmd, 1), &busy);
+ if (ret < 0)
+ return ret;
+ if ((busy & mask) == mask)
+ return 0;
+ }
+ return -EBUSY;
+}
+
+/**
+ * m5mols_enable_interrupt - Clear interrupt pending bits and unmask interrupts
+ *
+ * Before writing desired interrupt value the INT_FACTOR register should
+ * be read to clear pending interrupts.
+ */
+int m5mols_enable_interrupt(struct v4l2_subdev *sd, u32 reg)
+{
+ struct m5mols_info *info = to_m5mols(sd);
+ u32 mask = is_available_af(info) ? REG_INT_AF : 0;
+ u32 dummy;
+ int ret;
+
+ ret = m5mols_read(sd, SYSTEM_INT_FACTOR, &dummy);
+ if (!ret)
+ ret = m5mols_write(sd, SYSTEM_INT_ENABLE, reg & ~mask);
+ return ret;
+}
+
+/**
+ * m5mols_reg_mode - Write the mode and check busy status
+ *
+ * It always accompanies a little delay changing the M-5MOLS mode, so it is
+ * needed checking current busy status to guarantee right mode.
+ */
+static int m5mols_reg_mode(struct v4l2_subdev *sd, u32 mode)
+{
+ int ret = m5mols_write(sd, SYSTEM_SYSMODE, mode);
+
+ return ret ? ret : m5mols_busy(sd, CAT_SYSTEM, CAT0_SYSMODE, mode);
+}
+
+/**
+ * m5mols_mode - manage the M-5MOLS's mode
+ * @mode: the required operation mode
+ *
+ * The commands of M-5MOLS are grouped into specific modes. Each functionality
+ * can be guaranteed only when the sensor is operating in mode which which
+ * a command belongs to.
+ */
+int m5mols_mode(struct m5mols_info *info, u32 mode)
+{
+ struct v4l2_subdev *sd = &info->sd;
+ int ret = -EINVAL;
+ u32 reg;
+
+ if (mode < REG_PARAMETER && mode > REG_CAPTURE)
+ return ret;
+
+ ret = m5mols_read(sd, SYSTEM_SYSMODE, ®);
+ if ((!ret && reg == mode) || ret)
+ return ret;
+
+ switch (reg) {
+ case REG_PARAMETER:
+ ret = m5mols_reg_mode(sd, REG_MONITOR);
+ if (!ret && mode == REG_MONITOR)
+ break;
+ if (!ret)
+ ret = m5mols_reg_mode(sd, REG_CAPTURE);
+ break;
+
+ case REG_MONITOR:
+ if (mode == REG_PARAMETER) {
+ ret = m5mols_reg_mode(sd, REG_PARAMETER);
+ break;
+ }
+
+ ret = m5mols_reg_mode(sd, REG_CAPTURE);
+ break;
+
+ case REG_CAPTURE:
+ ret = m5mols_reg_mode(sd, REG_MONITOR);
+ if (!ret && mode == REG_MONITOR)
+ break;
+ if (!ret)
+ ret = m5mols_reg_mode(sd, REG_PARAMETER);
+ break;
+
+ default:
+ v4l2_warn(sd, "Wrong mode: %d\n", mode);
+ }
+
+ if (!ret)
+ info->mode = mode;
+
+ return ret;
+}
+
+/**
+ * m5mols_get_version - retrieve full revisions information of M-5MOLS
+ *
+ * The version information includes revisions of hardware and firmware,
+ * AutoFocus alghorithm version and the version string.
+ */
+static int m5mols_get_version(struct v4l2_subdev *sd)
+{
+ struct m5mols_info *info = to_m5mols(sd);
+ union {
+ struct m5mols_version ver;
+ u8 bytes[VERSION_SIZE];
+ } version;
+ u32 *value;
+ u8 cmd = CAT0_VER_CUSTOMER;
+ int ret;
+
+ do {
+ value = (u32 *)&version.bytes[cmd];
+ ret = m5mols_read(sd, SYSTEM_CMD(cmd), value);
+ if (ret)
+ return ret;
+ } while (cmd++ != CAT0_VER_AWB);
+
+ do {
+ value = (u32 *)&version.bytes[cmd];
+ ret = m5mols_read(sd, SYSTEM_VER_STRING, value);
+ if (ret)
+ return ret;
+ if (cmd >= VERSION_SIZE - 1)
+ return -EINVAL;
+ } while (version.bytes[cmd++]);
+
+ value = (u32 *)&version.bytes[cmd];
+ ret = m5mols_read(sd, AF_VERSION, value);
+ if (ret)
+ return ret;
+
+ /* store version information swapped for being readable */
+ info->ver = version.ver;
+ info->ver.fw = be16_to_cpu(info->ver.fw);
+ info->ver.hw = be16_to_cpu(info->ver.hw);
+ info->ver.param = be16_to_cpu(info->ver.param);
+ info->ver.awb = be16_to_cpu(info->ver.awb);
+
+ v4l2_info(sd, "Manufacturer\t[%s]\n",
+ is_manufacturer(info, REG_SAMSUNG_ELECTRO) ?
+ "Samsung Electro-Machanics" :
+ is_manufacturer(info, REG_SAMSUNG_OPTICS) ?
+ "Samsung Fiber-Optics" :
+ is_manufacturer(info, REG_SAMSUNG_TECHWIN) ?
+ "Samsung Techwin" : "None");
+ v4l2_info(sd, "Customer/Project\t[0x%02x/0x%02x]\n",
+ info->ver.customer, info->ver.project);
+
+ if (!is_available_af(info))
+ v4l2_info(sd, "No support Auto Focus on this firmware\n");
+
+ return ret;
+}
+
+/**
+ * __find_restype - Lookup M-5MOLS resolution type according to pixel code
+ * @code: pixel code
+ */
+static enum m5mols_restype __find_restype(enum v4l2_mbus_pixelcode code)
+{
+ enum m5mols_restype type = M5MOLS_RESTYPE_MONITOR;
+
+ do {
+ if (code == m5mols_default_ffmt[type].code)
+ return type;
+ } while (type++ != SIZE_DEFAULT_FFMT);
+
+ return 0;
+}
+
+/**
+ * __find_resolution - Lookup preset and type of M-5MOLS's resolution
+ * @mf: pixel format to find/negotiate the resolution preset for
+ * @type: M-5MOLS resolution type
+ * @resolution: M-5MOLS resolution preset register value
+ *
+ * Find nearest resolution matching resolution preset and adjust mf
+ * to supported values.
+ */
+static int __find_resolution(struct v4l2_subdev *sd,
+ struct v4l2_mbus_framefmt *mf,
+ enum m5mols_restype *type,
+ u32 *resolution)
+{
+ const struct m5mols_resolution *fsize = &m5mols_reg_res[0];
+ const struct m5mols_resolution *match = NULL;
+ enum m5mols_restype stype = __find_restype(mf->code);
+ int i = ARRAY_SIZE(m5mols_reg_res);
+ unsigned int min_err = ~0;
+
+ while (i--) {
+ int err;
+ if (stype == fsize->type) {
+ err = abs(fsize->width - mf->width)
+ + abs(fsize->height - mf->height);
+
+ if (err < min_err) {
+ min_err = err;
+ match = fsize;
+ }
+ }
+ fsize++;
+ }
+ if (match) {
+ mf->width = match->width;
+ mf->height = match->height;
+ *resolution = match->reg;
+ *type = stype;
+ return 0;
+ }
+
+ return -EINVAL;
+}
+
+static struct v4l2_mbus_framefmt *__find_format(struct m5mols_info *info,
+ struct v4l2_subdev_fh *fh,
+ enum v4l2_subdev_format_whence which,
+ enum m5mols_restype type)
+{
+ if (which == V4L2_SUBDEV_FORMAT_TRY)
+ return fh ? v4l2_subdev_get_try_format(fh, 0) : NULL;
+
+ return &info->ffmt[type];
+}
+
+static int m5mols_get_fmt(struct v4l2_subdev *sd, struct v4l2_subdev_fh *fh,
+ struct v4l2_subdev_format *fmt)
+{
+ struct m5mols_info *info = to_m5mols(sd);
+ struct v4l2_mbus_framefmt *format;
+
+ if (fmt->pad != 0)
+ return -EINVAL;
+
+ format = __find_format(info, fh, fmt->which, info->res_type);
+ if (!format)
+ return -EINVAL;
+
+ fmt->format = *format;
+ return 0;
+}
+
+static int m5mols_set_fmt(struct v4l2_subdev *sd, struct v4l2_subdev_fh *fh,
+ struct v4l2_subdev_format *fmt)
+{
+ struct m5mols_info *info = to_m5mols(sd);
+ struct v4l2_mbus_framefmt *format = &fmt->format;
+ struct v4l2_mbus_framefmt *sfmt;
+ enum m5mols_restype type;
+ u32 resolution = 0;
+ int ret;
+
+ if (fmt->pad != 0)
+ return -EINVAL;
+
+ ret = __find_resolution(sd, format, &type, &resolution);
+ if (ret < 0)
+ return ret;
+
+ sfmt = __find_format(info, fh, fmt->which, type);
+ if (!sfmt)
+ return 0;
+
+ *sfmt = m5mols_default_ffmt[type];
+ sfmt->width = format->width;
+ sfmt->height = format->height;
+
+ if (fmt->which == V4L2_SUBDEV_FORMAT_ACTIVE) {
+ info->resolution = resolution;
+ info->code = format->code;
+ info->res_type = type;
+ }
+
+ return 0;
+}
+
+static int m5mols_enum_mbus_code(struct v4l2_subdev *sd,
+ struct v4l2_subdev_fh *fh,
+ struct v4l2_subdev_mbus_code_enum *code)
+{
+ if (!code || code->index >= SIZE_DEFAULT_FFMT)
+ return -EINVAL;
+
+ code->code = m5mols_default_ffmt[code->index].code;
+
+ return 0;
+}
+
+static struct v4l2_subdev_pad_ops m5mols_pad_ops = {
+ .enum_mbus_code = m5mols_enum_mbus_code,
+ .get_fmt = m5mols_get_fmt,
+ .set_fmt = m5mols_set_fmt,
+};
+
+/**
+ * m5mols_sync_controls - Apply default scene mode and the current controls
+ *
+ * This is used only streaming for syncing between v4l2_ctrl framework and
+ * m5mols's controls. First, do the scenemode to the sensor, then call
+ * v4l2_ctrl_handler_setup. It can be same between some commands and
+ * the scenemode's in the default v4l2_ctrls. But, such commands of control
+ * should be prior to the scenemode's one.
+ */
+int m5mols_sync_controls(struct m5mols_info *info)
+{
+ int ret = -EINVAL;
+
+ if (!is_ctrl_synced(info)) {
+ ret = m5mols_do_scenemode(info, REG_SCENE_NORMAL);
+ if (ret)
+ return ret;
+
+ v4l2_ctrl_handler_setup(&info->handle);
+ info->ctrl_sync = true;
+ }
+
+ return ret;
+}
+
+/**
+ * m5mols_start_monitor - Start the monitor mode
+ *
+ * Before applying the controls setup the resolution and frame rate
+ * in PARAMETER mode, and then switch over to MONITOR mode.
+ */
+static int m5mols_start_monitor(struct m5mols_info *info)
+{
+ struct v4l2_subdev *sd = &info->sd;
+ int ret;
+
+ ret = m5mols_mode(info, REG_PARAMETER);
+ if (!ret)
+ ret = m5mols_write(sd, PARM_MON_SIZE, info->resolution);
+ if (!ret)
+ ret = m5mols_write(sd, PARM_MON_FPS, REG_FPS_30);
+ if (!ret)
+ ret = m5mols_mode(info, REG_MONITOR);
+ if (!ret)
+ ret = m5mols_sync_controls(info);
+
+ return ret;
+}
+
+static int m5mols_s_stream(struct v4l2_subdev *sd, int enable)
+{
+ struct m5mols_info *info = to_m5mols(sd);
+
+ if (enable) {
+ int ret = -EINVAL;
+
+ if (is_code(info->code, M5MOLS_RESTYPE_MONITOR))
+ ret = m5mols_start_monitor(info);
+ if (is_code(info->code, M5MOLS_RESTYPE_CAPTURE))
+ ret = m5mols_start_capture(info);
+
+ return ret;
+ }
+
+ return m5mols_mode(info, REG_PARAMETER);
+}
+
+static const struct v4l2_subdev_video_ops m5mols_video_ops = {
+ .s_stream = m5mols_s_stream,
+};
+
+static int m5mols_s_ctrl(struct v4l2_ctrl *ctrl)
+{
+ struct v4l2_subdev *sd = to_sd(ctrl);
+ struct m5mols_info *info = to_m5mols(sd);
+ int ret;
+
+ info->mode_save = info->mode;
+
+ ret = m5mols_mode(info, REG_PARAMETER);
+ if (!ret)
+ ret = m5mols_set_ctrl(ctrl);
+ if (!ret)
+ ret = m5mols_mode(info, info->mode_save);
+
+ return ret;
+}
+
+static const struct v4l2_ctrl_ops m5mols_ctrl_ops = {
+ .s_ctrl = m5mols_s_ctrl,
+};
+
+static int m5mols_sensor_power(struct m5mols_info *info, bool enable)
+{
+ struct v4l2_subdev *sd = &info->sd;
+ struct i2c_client *client = v4l2_get_subdevdata(sd);
+ const struct m5mols_platform_data *pdata = info->pdata;
+ int ret;
+
+ if (enable) {
+ if (is_powered(info))
+ return 0;
+
+ if (info->set_power) {
+ ret = info->set_power(&client->dev, 1);
+ if (ret)
+ return ret;
+ }
+
+ ret = regulator_bulk_enable(ARRAY_SIZE(supplies), supplies);
+ if (ret) {
+ info->set_power(&client->dev, 0);
+ return ret;
+ }
+
+ gpio_set_value(pdata->gpio_reset, !pdata->reset_polarity);
+ usleep_range(1000, 1000);
+ info->power = true;
+
+ return ret;
+ }
+
+ if (!is_powered(info))
+ return 0;
+
+ ret = regulator_bulk_disable(ARRAY_SIZE(supplies), supplies);
+ if (ret)
+ return ret;
+
+ if (info->set_power)
+ info->set_power(&client->dev, 0);
+
+ gpio_set_value(pdata->gpio_reset, pdata->reset_polarity);
+ usleep_range(1000, 1000);
+ info->power = false;
+
+ return ret;
+}
+
+/* m5mols_update_fw - optional firmware update routine */
+int __attribute__ ((weak)) m5mols_update_fw(struct v4l2_subdev *sd,
+ int (*set_power)(struct m5mols_info *, bool))
+{
+ return 0;
+}
+
+/**
+ * m5mols_sensor_armboot - Booting M-5MOLS internal ARM core.
+ *
+ * Booting internal ARM core makes the M-5MOLS is ready for getting commands
+ * with I2C. It's the first thing to be done after it powered up. It must wait
+ * at least 520ms recommended by M-5MOLS datasheet, after executing arm booting.
+ */
+static int m5mols_sensor_armboot(struct v4l2_subdev *sd)
+{
+ int ret;
+
+ ret = m5mols_write(sd, FLASH_CAM_START, REG_START_ARM_BOOT);
+ if (ret < 0)
+ return ret;
+
+ msleep(520);
+
+ ret = m5mols_get_version(sd);
+ if (!ret)
+ ret = m5mols_update_fw(sd, m5mols_sensor_power);
+ if (ret)
+ return ret;
+
+ v4l2_dbg(1, m5mols_debug, sd, "Success ARM Booting\n");
+
+ ret = m5mols_write(sd, PARM_INTERFACE, REG_INTERFACE_MIPI);
+ if (!ret)
+ ret = m5mols_enable_interrupt(sd, REG_INT_AF);
+
+ return ret;
+}
+
+static int m5mols_init_controls(struct m5mols_info *info)
+{
+ struct v4l2_subdev *sd = &info->sd;
+ u16 max_exposure;
+ u16 step_zoom;
+ int ret;
+
+ /* Determine value's range & step of controls for various FW version */
+ ret = m5mols_read(sd, AE_MAX_GAIN_MON, (u32 *)&max_exposure);
+ if (!ret)
+ step_zoom = is_manufacturer(info, REG_SAMSUNG_OPTICS) ? 31 : 1;
+ if (ret)
+ return ret;
+
+ v4l2_ctrl_handler_init(&info->handle, 6);
+ info->autowb = v4l2_ctrl_new_std(&info->handle,
+ &m5mols_ctrl_ops, V4L2_CID_AUTO_WHITE_BALANCE,
+ 0, 1, 1, 0);
+ info->saturation = v4l2_ctrl_new_std(&info->handle,
+ &m5mols_ctrl_ops, V4L2_CID_SATURATION,
+ 1, 5, 1, 3);
+ info->zoom = v4l2_ctrl_new_std(&info->handle,
+ &m5mols_ctrl_ops, V4L2_CID_ZOOM_ABSOLUTE,
+ 1, 70, step_zoom, 1);
+ info->exposure = v4l2_ctrl_new_std(&info->handle,
+ &m5mols_ctrl_ops, V4L2_CID_EXPOSURE,
+ 0, max_exposure, 1, (int)max_exposure/2);
+ info->colorfx = v4l2_ctrl_new_std_menu(&info->handle,
+ &m5mols_ctrl_ops, V4L2_CID_COLORFX,
+ 4, (1 << V4L2_COLORFX_BW), V4L2_COLORFX_NONE);
+ info->autoexposure = v4l2_ctrl_new_std_menu(&info->handle,
+ &m5mols_ctrl_ops, V4L2_CID_EXPOSURE_AUTO,
+ 1, 0, V4L2_EXPOSURE_MANUAL);
+
+ sd->ctrl_handler = &info->handle;
+ if (info->handle.error) {
+ v4l2_err(sd, "Failed to initialize controls: %d\n", ret);
+ v4l2_ctrl_handler_free(&info->handle);
+ return info->handle.error;
+ }
+
+ v4l2_ctrl_cluster(2, &info->autoexposure);
+
+ return 0;
+}
+
+/**
+ * m5mols_s_power - Main sensor power control function
+ *
+ * To prevent breaking the lens when the sensor is powered off the Soft-Landing
+ * algorithm is called where available. The Soft-Landing algorithm availability
+ * dependends on the firmware provider.
+ */
+static int m5mols_s_power(struct v4l2_subdev *sd, int on)
+{
+ struct m5mols_info *info = to_m5mols(sd);
+ int ret;
+
+ if (on) {
+ ret = m5mols_sensor_power(info, true);
+ if (!ret)
+ ret = m5mols_sensor_armboot(sd);
+ if (!ret)
+ ret = m5mols_init_controls(info);
+ if (ret)
+ return ret;
+
+ info->ffmt[M5MOLS_RESTYPE_MONITOR] =
+ m5mols_default_ffmt[M5MOLS_RESTYPE_MONITOR];
+ info->ffmt[M5MOLS_RESTYPE_CAPTURE] =
+ m5mols_default_ffmt[M5MOLS_RESTYPE_CAPTURE];
+ return ret;
+ }
+
+ if (is_manufacturer(info, REG_SAMSUNG_TECHWIN)) {
+ ret = m5mols_mode(info, REG_MONITOR);
+ if (!ret)
+ ret = m5mols_write(sd, AF_EXECUTE, REG_AF_STOP);
+ if (!ret)
+ ret = m5mols_write(sd, AF_MODE, REG_AF_POWEROFF);
+ if (!ret)
+ ret = m5mols_busy(sd, CAT_SYSTEM, CAT0_STATUS,
+ REG_AF_IDLE);
+ if (!ret)
+ v4l2_info(sd, "Success soft-landing lens\n");
+ }
+
+ ret = m5mols_sensor_power(info, false);
+ if (!ret) {
+ v4l2_ctrl_handler_free(&info->handle);
+ info->ctrl_sync = false;
+ }
+
+ return ret;
+}
+
+static int m5mols_log_status(struct v4l2_subdev *sd)
+{
+ struct m5mols_info *info = to_m5mols(sd);
+
+ v4l2_ctrl_handler_log_status(&info->handle, sd->name);
+
+ return 0;
+}
+
+static const struct v4l2_subdev_core_ops m5mols_core_ops = {
+ .s_power = m5mols_s_power,
+ .g_ctrl = v4l2_subdev_g_ctrl,
+ .s_ctrl = v4l2_subdev_s_ctrl,
+ .queryctrl = v4l2_subdev_queryctrl,
+ .querymenu = v4l2_subdev_querymenu,
+ .g_ext_ctrls = v4l2_subdev_g_ext_ctrls,
+ .try_ext_ctrls = v4l2_subdev_try_ext_ctrls,
+ .s_ext_ctrls = v4l2_subdev_s_ext_ctrls,
+ .log_status = m5mols_log_status,
+};
+
+static const struct v4l2_subdev_ops m5mols_ops = {
+ .core = &m5mols_core_ops,
+ .pad = &m5mols_pad_ops,
+ .video = &m5mols_video_ops,
+};
+
+static void m5mols_irq_work(struct work_struct *work)
+{
+ struct m5mols_info *info =
+ container_of(work, struct m5mols_info, work_irq);
+ struct v4l2_subdev *sd = &info->sd;
+ u32 reg;
+ int ret;
+
+ if (!is_powered(info) ||
+ m5mols_read(sd, SYSTEM_INT_FACTOR, &info->interrupt))
+ return;
+
+ switch (info->interrupt & REG_INT_MASK) {
+ case REG_INT_AF:
+ if (!is_available_af(info))
+ break;
+ ret = m5mols_read(sd, AF_STATUS, ®);
+ v4l2_dbg(2, m5mols_debug, sd, "AF %s\n",
+ reg == REG_AF_FAIL ? "Failed" :
+ reg == REG_AF_SUCCESS ? "Success" :
+ reg == REG_AF_IDLE ? "Idle" : "Busy");
+ break;
+ case REG_INT_CAPTURE:
+ if (!test_and_set_bit(ST_CAPT_IRQ, &info->flags))
+ wake_up_interruptible(&info->irq_waitq);
+
+ v4l2_dbg(2, m5mols_debug, sd, "CAPTURE\n");
+ break;
+ default:
+ v4l2_dbg(2, m5mols_debug, sd, "Undefined: %02x\n", reg);
+ break;
+ };
+}
+
+static irqreturn_t m5mols_irq_handler(int irq, void *data)
+{
+ struct v4l2_subdev *sd = data;
+ struct m5mols_info *info = to_m5mols(sd);
+
+ schedule_work(&info->work_irq);
+
+ return IRQ_HANDLED;
+}
+
+static int __devinit m5mols_probe(struct i2c_client *client,
+ const struct i2c_device_id *id)
+{
+ const struct m5mols_platform_data *pdata = client->dev.platform_data;
+ struct m5mols_info *info;
+ struct v4l2_subdev *sd;
+ int ret;
+
+ if (pdata == NULL) {
+ dev_err(&client->dev, "No platform data\n");
+ return -EINVAL;
+ }
+
+ if (!gpio_is_valid(pdata->gpio_reset)) {
+ dev_err(&client->dev, "No valid RESET GPIO specified\n");
+ return -EINVAL;
+ }
+
+ if (!pdata->irq) {
+ dev_err(&client->dev, "Interrupt not assigned\n");
+ return -EINVAL;
+ }
+
+ info = kzalloc(sizeof(struct m5mols_info), GFP_KERNEL);
+ if (!info)
+ return -ENOMEM;
+
+ info->pdata = pdata;
+ info->set_power = pdata->set_power;
+
+ ret = gpio_request(pdata->gpio_reset, "M5MOLS_NRST");
+ if (ret) {
+ dev_err(&client->dev, "Failed to request gpio: %d\n", ret);
+ goto out_free;
+ }
+ gpio_direction_output(pdata->gpio_reset, pdata->reset_polarity);
+
+ ret = regulator_bulk_get(&client->dev, ARRAY_SIZE(supplies), supplies);
+ if (ret) {
+ dev_err(&client->dev, "Failed to get regulators: %d\n", ret);
+ goto out_gpio;
+ }
+
+ sd = &info->sd;
+ strlcpy(sd->name, MODULE_NAME, sizeof(sd->name));
+ v4l2_i2c_subdev_init(sd, client, &m5mols_ops);
+
+ info->pad.flags = MEDIA_PAD_FL_SOURCE;
+ ret = media_entity_init(&sd->entity, 1, &info->pad, 0);
+ if (ret < 0)
+ goto out_reg;
+ sd->entity.type = MEDIA_ENT_T_V4L2_SUBDEV_SENSOR;
+
+ init_waitqueue_head(&info->irq_waitq);
+ INIT_WORK(&info->work_irq, m5mols_irq_work);
+ ret = request_irq(pdata->irq, m5mols_irq_handler,
+ IRQF_TRIGGER_RISING, MODULE_NAME, sd);
+ if (ret) {
+ dev_err(&client->dev, "Interrupt request failed: %d\n", ret);
+ goto out_me;
+ }
+ info->res_type = M5MOLS_RESTYPE_MONITOR;
+ return 0;
+out_me:
+ media_entity_cleanup(&sd->entity);
+out_reg:
+ regulator_bulk_free(ARRAY_SIZE(supplies), supplies);
+out_gpio:
+ gpio_free(pdata->gpio_reset);
+out_free:
+ kfree(info);
+ return ret;
+}
+
+static int __devexit m5mols_remove(struct i2c_client *client)
+{
+ struct v4l2_subdev *sd = i2c_get_clientdata(client);
+ struct m5mols_info *info = to_m5mols(sd);
+
+ v4l2_device_unregister_subdev(sd);
+ free_irq(info->pdata->irq, sd);
+
+ regulator_bulk_free(ARRAY_SIZE(supplies), supplies);
+ gpio_free(info->pdata->gpio_reset);
+ media_entity_cleanup(&sd->entity);
+ kfree(info);
+ return 0;
+}
+
+static const struct i2c_device_id m5mols_id[] = {
+ { MODULE_NAME, 0 },
+ { },
+};
+MODULE_DEVICE_TABLE(i2c, m5mols_id);
+
+static struct i2c_driver m5mols_i2c_driver = {
+ .driver = {
+ .name = MODULE_NAME,
+ },
+ .probe = m5mols_probe,
+ .remove = __devexit_p(m5mols_remove),
+ .id_table = m5mols_id,
+};
+
+static int __init m5mols_mod_init(void)
+{
+ return i2c_add_driver(&m5mols_i2c_driver);
+}
+
+static void __exit m5mols_mod_exit(void)
+{
+ i2c_del_driver(&m5mols_i2c_driver);
+}
+
+module_init(m5mols_mod_init);
+module_exit(m5mols_mod_exit);
+
+MODULE_AUTHOR("HeungJun Kim <riverful.kim@samsung.com>");
+MODULE_AUTHOR("Dongsoo Kim <dongsoo45.kim@samsung.com>");
+MODULE_DESCRIPTION("Fujitsu M-5MOLS 8M Pixel camera driver");
+MODULE_LICENSE("GPL");
diff --git a/drivers/media/video/m5mols/m5mols_reg.h b/drivers/media/video/m5mols/m5mols_reg.h
new file mode 100644
index 0000000..b83e36f
--- /dev/null
+++ b/drivers/media/video/m5mols/m5mols_reg.h
@@ -0,0 +1,399 @@
+/*
+ * Register map for M-5MOLS 8M Pixel camera sensor with ISP
+ *
+ * Copyright (C) 2011 Samsung Electronics Co., Ltd.
+ * Author: HeungJun Kim, riverful.kim@samsung.com
+ *
+ * Copyright (C) 2009 Samsung Electronics Co., Ltd.
+ * Author: Dongsoo Nathaniel Kim, dongsoo45.kim@samsung.com
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#ifndef M5MOLS_REG_H
+#define M5MOLS_REG_H
+
+#define M5MOLS_I2C_MAX_SIZE 4
+#define M5MOLS_BYTE_READ 0x01
+#define M5MOLS_BYTE_WRITE 0x02
+
+#define I2C_CATEGORY(__cat) ((__cat >> 16) & 0xff)
+#define I2C_COMMAND(__comm) ((__comm >> 8) & 0xff)
+#define I2C_SIZE(__reg_s) ((__reg_s) & 0xff)
+#define I2C_REG(__cat, __cmd, __reg_s) ((__cat << 16) | (__cmd << 8) | __reg_s)
+
+/*
+ * Category section register
+ *
+ * The category means set including relevant command of M-5MOLS.
+ */
+#define CAT_SYSTEM 0x00
+#define CAT_PARAM 0x01
+#define CAT_MONITOR 0x02
+#define CAT_AE 0x03
+#define CAT_WB 0x06
+#define CAT_EXIF 0x07
+#define CAT_FD 0x09
+#define CAT_LENS 0x0a
+#define CAT_CAPT_PARM 0x0b
+#define CAT_CAPT_CTRL 0x0c
+#define CAT_FLASH 0x0f /* related to FW, revisions, booting */
+
+/*
+ * Category 0 - SYSTEM mode
+ *
+ * The SYSTEM mode in the M-5MOLS means area available to handle with the whole
+ * & all-round system of sensor. It deals with version/interrupt/setting mode &
+ * even sensor's status. Especially, the M-5MOLS sensor with ISP varies by
+ * packaging & manufacturer, even the customer and project code. And the
+ * function details may vary among them. The version information helps to
+ * determine what methods shall be used in the driver.
+ *
+ * There is many registers between customer version address and awb one. For
+ * more specific contents, see definition if file m5mols.h.
+ */
+#define CAT0_VER_CUSTOMER 0x00 /* customer version */
+#define CAT0_VER_AWB 0x09 /* Auto WB version */
+#define CAT0_VER_STRING 0x0a /* string including M-5MOLS */
+#define CAT0_SYSMODE 0x0b /* SYSTEM mode register */
+#define CAT0_STATUS 0x0c /* SYSTEM mode status register */
+#define CAT0_INT_FACTOR 0x10 /* interrupt pending register */
+#define CAT0_INT_ENABLE 0x11 /* interrupt enable register */
+
+#define SYSTEM_SYSMODE I2C_REG(CAT_SYSTEM, CAT0_SYSMODE, 1)
+#define REG_SYSINIT 0x00 /* SYSTEM mode */
+#define REG_PARAMETER 0x01 /* PARAMETER mode */
+#define REG_MONITOR 0x02 /* MONITOR mode */
+#define REG_CAPTURE 0x03 /* CAPTURE mode */
+
+#define SYSTEM_CMD(__cmd) I2C_REG(CAT_SYSTEM, cmd, 1)
+#define SYSTEM_VER_STRING I2C_REG(CAT_SYSTEM, CAT0_VER_STRING, 1)
+#define REG_SAMSUNG_ELECTRO "SE" /* Samsung Electro-Mechanics */
+#define REG_SAMSUNG_OPTICS "OP" /* Samsung Fiber-Optics */
+#define REG_SAMSUNG_TECHWIN "TB" /* Samsung Techwin */
+
+#define SYSTEM_INT_FACTOR I2C_REG(CAT_SYSTEM, CAT0_INT_FACTOR, 1)
+#define SYSTEM_INT_ENABLE I2C_REG(CAT_SYSTEM, CAT0_INT_ENABLE, 1)
+#define REG_INT_MODE (1 << 0)
+#define REG_INT_AF (1 << 1)
+#define REG_INT_ZOOM (1 << 2)
+#define REG_INT_CAPTURE (1 << 3)
+#define REG_INT_FRAMESYNC (1 << 4)
+#define REG_INT_FD (1 << 5)
+#define REG_INT_LENS_INIT (1 << 6)
+#define REG_INT_SOUND (1 << 7)
+#define REG_INT_MASK 0x0f
+
+/*
+ * category 1 - PARAMETER mode
+ *
+ * This category supports function of camera features of M-5MOLS. It means we
+ * can handle with preview(MONITOR) resolution size/frame per second/interface
+ * between the sensor and the Application Processor/even the image effect.
+ */
+#define CAT1_DATA_INTERFACE 0x00 /* interface between sensor and AP */
+#define CAT1_MONITOR_SIZE 0x01 /* resolution at the MONITOR mode */
+#define CAT1_MONITOR_FPS 0x02 /* frame per second at this mode */
+#define CAT1_EFFECT 0x0b /* image effects */
+
+#define PARM_MON_SIZE I2C_REG(CAT_PARAM, CAT1_MONITOR_SIZE, 1)
+
+#define PARM_MON_FPS I2C_REG(CAT_PARAM, CAT1_MONITOR_FPS, 1)
+#define REG_FPS_30 0x02
+
+#define PARM_INTERFACE I2C_REG(CAT_PARAM, CAT1_DATA_INTERFACE, 1)
+#define REG_INTERFACE_MIPI 0x02
+
+#define PARM_EFFECT I2C_REG(CAT_PARAM, CAT1_EFFECT, 1)
+#define REG_EFFECT_OFF 0x00
+#define REG_EFFECT_NEGA 0x01
+#define REG_EFFECT_EMBOSS 0x06
+#define REG_EFFECT_OUTLINE 0x07
+#define REG_EFFECT_WATERCOLOR 0x08
+
+/*
+ * Category 2 - MONITOR mode
+ *
+ * The MONITOR mode is same as preview mode as we said. The M-5MOLS has another
+ * mode named "Preview", but this preview mode is used at the case specific
+ * vider-recording mode. This mmode supports only YUYV format. On the other
+ * hand, the JPEG & RAW formats is supports by CAPTURE mode. And, there are
+ * another options like zoom/color effect(different with effect in PARAMETER
+ * mode)/anti hand shaking algorithm.
+ */
+#define CAT2_ZOOM 0x01 /* set the zoom position & execute */
+#define CAT2_ZOOM_STEP 0x03 /* set the zoom step */
+#define CAT2_CFIXB 0x09 /* CB value for color effect */
+#define CAT2_CFIXR 0x0a /* CR value for color effect */
+#define CAT2_COLOR_EFFECT 0x0b /* set on/off of color effect */
+#define CAT2_CHROMA_LVL 0x0f /* set chroma level */
+#define CAT2_CHROMA_EN 0x10 /* set on/off of choroma */
+#define CAT2_EDGE_LVL 0x11 /* set sharpness level */
+#define CAT2_EDGE_EN 0x12 /* set on/off sharpness */
+#define CAT2_TONE_CTL 0x25 /* set tone color(contrast) */
+
+#define MON_ZOOM I2C_REG(CAT_MONITOR, CAT2_ZOOM, 1)
+
+#define MON_CFIXR I2C_REG(CAT_MONITOR, CAT2_CFIXR, 1)
+#define MON_CFIXB I2C_REG(CAT_MONITOR, CAT2_CFIXB, 1)
+#define REG_CFIXB_SEPIA 0xd8
+#define REG_CFIXR_SEPIA 0x18
+
+#define MON_EFFECT I2C_REG(CAT_MONITOR, CAT2_COLOR_EFFECT, 1)
+#define REG_COLOR_EFFECT_OFF 0x00
+#define REG_COLOR_EFFECT_ON 0x01
+
+#define MON_CHROMA_EN I2C_REG(CAT_MONITOR, CAT2_CHROMA_EN, 1)
+#define MON_CHROMA_LVL I2C_REG(CAT_MONITOR, CAT2_CHROMA_LVL, 1)
+#define REG_CHROMA_OFF 0x00
+#define REG_CHROMA_ON 0x01
+
+#define MON_EDGE_EN I2C_REG(CAT_MONITOR, CAT2_EDGE_EN, 1)
+#define MON_EDGE_LVL I2C_REG(CAT_MONITOR, CAT2_EDGE_LVL, 1)
+#define REG_EDGE_OFF 0x00
+#define REG_EDGE_ON 0x01
+
+#define MON_TONE_CTL I2C_REG(CAT_MONITOR, CAT2_TONE_CTL, 1)
+
+/*
+ * Category 3 - Auto Exposure
+ *
+ * The M-5MOLS exposure capbility is detailed as which is similar to digital
+ * camera. This category supports AE locking/various AE mode(range of exposure)
+ * /ISO/flickering/EV bias/shutter/meteoring, and anything else. And the
+ * maximum/minimum exposure gain value depending on M-5MOLS firmware, may be
+ * different. So, this category also provide getting the max/min values. And,
+ * each MONITOR and CAPTURE mode has each gain/shutter/max exposure values.
+ */
+#define CAT3_AE_LOCK 0x00 /* locking Auto exposure */
+#define CAT3_AE_MODE 0x01 /* set AE mode, mode means range */
+#define CAT3_ISO 0x05 /* set ISO */
+#define CAT3_EV_PRESET_MONITOR 0x0a /* EV(scenemode) preset for MONITOR */
+#define CAT3_EV_PRESET_CAPTURE 0x0b /* EV(scenemode) preset for CAPTURE */
+#define CAT3_MANUAL_GAIN_MON 0x12 /* meteoring value for the MONITOR */
+#define CAT3_MAX_GAIN_MON 0x1a /* max gain value for the MONITOR */
+#define CAT3_MANUAL_GAIN_CAP 0x26 /* meteoring value for the CAPTURE */
+#define CAT3_AE_INDEX 0x38 /* AE index */
+
+#define AE_LOCK I2C_REG(CAT_AE, CAT3_AE_LOCK, 1)
+#define REG_AE_UNLOCK 0x00
+#define REG_AE_LOCK 0x01
+
+#define AE_MODE I2C_REG(CAT_AE, CAT3_AE_MODE, 1)
+#define REG_AE_OFF 0x00 /* AE off */
+#define REG_AE_ALL 0x01 /* calc AE in all block integral */
+#define REG_AE_CENTER 0x03 /* calc AE in center weighted */
+#define REG_AE_SPOT 0x06 /* calc AE in specific spot */
+
+#define AE_ISO I2C_REG(CAT_AE, CAT3_ISO, 1)
+#define REG_ISO_AUTO 0x00
+#define REG_ISO_50 0x01
+#define REG_ISO_100 0x02
+#define REG_ISO_200 0x03
+#define REG_ISO_400 0x04
+#define REG_ISO_800 0x05
+
+#define AE_EV_PRESET_MONITOR I2C_REG(CAT_AE, CAT3_EV_PRESET_MONITOR, 1)
+#define AE_EV_PRESET_CAPTURE I2C_REG(CAT_AE, CAT3_EV_PRESET_CAPTURE, 1)
+#define REG_SCENE_NORMAL 0x00
+#define REG_SCENE_PORTRAIT 0x01
+#define REG_SCENE_LANDSCAPE 0x02
+#define REG_SCENE_SPORTS 0x03
+#define REG_SCENE_PARTY_INDOOR 0x04
+#define REG_SCENE_BEACH_SNOW 0x05
+#define REG_SCENE_SUNSET 0x06
+#define REG_SCENE_DAWN_DUSK 0x07
+#define REG_SCENE_FALL 0x08
+#define REG_SCENE_NIGHT 0x09
+#define REG_SCENE_AGAINST_LIGHT 0x0a
+#define REG_SCENE_FIRE 0x0b
+#define REG_SCENE_TEXT 0x0c
+#define REG_SCENE_CANDLE 0x0d
+
+#define AE_MAN_GAIN_MON I2C_REG(CAT_AE, CAT3_MANUAL_GAIN_MON, 2)
+#define AE_MAX_GAIN_MON I2C_REG(CAT_AE, CAT3_MAX_GAIN_MON, 2)
+#define AE_MAN_GAIN_CAP I2C_REG(CAT_AE, CAT3_MANUAL_GAIN_CAP, 2)
+
+#define AE_INDEX I2C_REG(CAT_AE, CAT3_AE_INDEX, 1)
+#define REG_AE_INDEX_20_NEG 0x00
+#define REG_AE_INDEX_15_NEG 0x01
+#define REG_AE_INDEX_10_NEG 0x02
+#define REG_AE_INDEX_05_NEG 0x03
+#define REG_AE_INDEX_00 0x04
+#define REG_AE_INDEX_05_POS 0x05
+#define REG_AE_INDEX_10_POS 0x06
+#define REG_AE_INDEX_15_POS 0x07
+#define REG_AE_INDEX_20_POS 0x08
+
+/*
+ * Category 6 - White Balance
+ *
+ * This category provide AWB locking/mode/preset/speed/gain bias, etc.
+ */
+#define CAT6_AWB_LOCK 0x00 /* locking Auto Whitebalance */
+#define CAT6_AWB_MODE 0x02 /* set Auto or Manual */
+#define CAT6_AWB_MANUAL 0x03 /* set Manual(preset) value */
+
+#define AWB_LOCK I2C_REG(CAT_WB, CAT6_AWB_LOCK, 1)
+#define REG_AWB_UNLOCK 0x00
+#define REG_AWB_LOCK 0x01
+
+#define AWB_MODE I2C_REG(CAT_WB, CAT6_AWB_MODE, 1)
+#define REG_AWB_AUTO 0x01 /* AWB off */
+#define REG_AWB_PRESET 0x02 /* AWB preset */
+
+#define AWB_MANUAL I2C_REG(CAT_WB, CAT6_AWB_MANUAL, 1)
+#define REG_AWB_INCANDESCENT 0x01
+#define REG_AWB_FLUORESCENT_1 0x02
+#define REG_AWB_FLUORESCENT_2 0x03
+#define REG_AWB_DAYLIGHT 0x04
+#define REG_AWB_CLOUDY 0x05
+#define REG_AWB_SHADE 0x06
+#define REG_AWB_HORIZON 0x07
+#define REG_AWB_LEDLIGHT 0x09
+
+/*
+ * Category 7 - EXIF information
+ */
+#define CAT7_INFO_EXPTIME_NU 0x00
+#define CAT7_INFO_EXPTIME_DE 0x04
+#define CAT7_INFO_TV_NU 0x08
+#define CAT7_INFO_TV_DE 0x0c
+#define CAT7_INFO_AV_NU 0x10
+#define CAT7_INFO_AV_DE 0x14
+#define CAT7_INFO_BV_NU 0x18
+#define CAT7_INFO_BV_DE 0x1c
+#define CAT7_INFO_EBV_NU 0x20
+#define CAT7_INFO_EBV_DE 0x24
+#define CAT7_INFO_ISO 0x28
+#define CAT7_INFO_FLASH 0x2a
+#define CAT7_INFO_SDR 0x2c
+#define CAT7_INFO_QVAL 0x2e
+
+#define EXIF_INFO_EXPTIME_NU I2C_REG(CAT_EXIF, CAT7_INFO_EXPTIME_NU, 4)
+#define EXIF_INFO_EXPTIME_DE I2C_REG(CAT_EXIF, CAT7_INFO_EXPTIME_DE, 4)
+#define EXIF_INFO_TV_NU I2C_REG(CAT_EXIF, CAT7_INFO_TV_NU, 4)
+#define EXIF_INFO_TV_DE I2C_REG(CAT_EXIF, CAT7_INFO_TV_DE, 4)
+#define EXIF_INFO_AV_NU I2C_REG(CAT_EXIF, CAT7_INFO_AV_NU, 4)
+#define EXIF_INFO_AV_DE I2C_REG(CAT_EXIF, CAT7_INFO_AV_DE, 4)
+#define EXIF_INFO_BV_NU I2C_REG(CAT_EXIF, CAT7_INFO_BV_NU, 4)
+#define EXIF_INFO_BV_DE I2C_REG(CAT_EXIF, CAT7_INFO_BV_DE, 4)
+#define EXIF_INFO_EBV_NU I2C_REG(CAT_EXIF, CAT7_INFO_EBV_NU, 4)
+#define EXIF_INFO_EBV_DE I2C_REG(CAT_EXIF, CAT7_INFO_EBV_DE, 4)
+#define EXIF_INFO_ISO I2C_REG(CAT_EXIF, CAT7_INFO_ISO, 2)
+#define EXIF_INFO_FLASH I2C_REG(CAT_EXIF, CAT7_INFO_FLASH, 2)
+#define EXIF_INFO_SDR I2C_REG(CAT_EXIF, CAT7_INFO_SDR, 2)
+#define EXIF_INFO_QVAL I2C_REG(CAT_EXIF, CAT7_INFO_QVAL, 2)
+
+/*
+ * Category 9 - Face Detection
+ */
+#define CAT9_FD_CTL 0x00
+
+#define FD_CTL I2C_REG(CAT_FD, CAT9_FD_CTL, 1)
+#define BIT_FD_EN 0
+#define BIT_FD_DRAW_FACE_FRAME 4
+#define BIT_FD_DRAW_SMILE_LVL 6
+#define REG_FD(shift) (1 << shift)
+#define REG_FD_OFF 0x0
+
+/*
+ * Category A - Lens Parameter
+ */
+#define CATA_AF_MODE 0x01
+#define CATA_AF_EXECUTE 0x02
+#define CATA_AF_STATUS 0x03
+#define CATA_AF_VERSION 0x0a
+
+#define AF_MODE I2C_REG(CAT_LENS, CATA_AF_MODE, 1)
+#define REG_AF_NORMAL 0x00 /* Normal AF, one time */
+#define REG_AF_MACRO 0x01 /* Macro AF, one time */
+#define REG_AF_POWEROFF 0x07
+
+#define AF_EXECUTE I2C_REG(CAT_LENS, CATA_AF_EXECUTE, 1)
+#define REG_AF_STOP 0x00
+#define REG_AF_EXE_AUTO 0x01
+#define REG_AF_EXE_CAF 0x02
+
+#define AF_STATUS I2C_REG(CAT_LENS, CATA_AF_STATUS, 1)
+#define REG_AF_FAIL 0x00
+#define REG_AF_SUCCESS 0x02
+#define REG_AF_IDLE 0x04
+#define REG_AF_BUSY 0x05
+
+#define AF_VERSION I2C_REG(CAT_LENS, CATA_AF_VERSION, 1)
+
+/*
+ * Category B - CAPTURE Parameter
+ */
+#define CATB_YUVOUT_MAIN 0x00
+#define CATB_MAIN_IMAGE_SIZE 0x01
+#define CATB_MCC_MODE 0x1d
+#define CATB_WDR_EN 0x2c
+#define CATB_LIGHT_CTRL 0x40
+#define CATB_FLASH_CTRL 0x41
+
+#define CAPP_YUVOUT_MAIN I2C_REG(CAT_CAPT_PARM, CATB_YUVOUT_MAIN, 1)
+#define REG_YUV422 0x00
+#define REG_BAYER10 0x05
+#define REG_BAYER8 0x06
+#define REG_JPEG 0x10
+
+#define CAPP_MAIN_IMAGE_SIZE I2C_REG(CAT_CAPT_PARM, CATB_MAIN_IMAGE_SIZE, 1)
+
+#define CAPP_MCC_MODE I2C_REG(CAT_CAPT_PARM, CATB_MCC_MODE, 1)
+#define REG_MCC_OFF 0x00
+#define REG_MCC_NORMAL 0x01
+
+#define CAPP_WDR_EN I2C_REG(CAT_CAPT_PARM, CATB_WDR_EN, 1)
+#define REG_WDR_OFF 0x00
+#define REG_WDR_ON 0x01
+#define REG_WDR_AUTO 0x02
+
+#define CAPP_LIGHT_CTRL I2C_REG(CAT_CAPT_PARM, CATB_LIGHT_CTRL, 1)
+#define REG_LIGHT_OFF 0x00
+#define REG_LIGHT_ON 0x01
+#define REG_LIGHT_AUTO 0x02
+
+#define CAPP_FLASH_CTRL I2C_REG(CAT_CAPT_PARM, CATB_FLASH_CTRL, 1)
+#define REG_FLASH_OFF 0x00
+#define REG_FLASH_ON 0x01
+#define REG_FLASH_AUTO 0x02
+
+/*
+ * Category C - CAPTURE Control
+ */
+#define CATC_CAP_MODE 0x00
+#define CATC_CAP_SEL_FRAME 0x06 /* It determines Single or Multi */
+#define CATC_CAP_START 0x09
+#define CATC_CAP_IMAGE_SIZE 0x0d
+#define CATC_CAP_THUMB_SIZE 0x11
+
+#define CAPC_MODE I2C_REG(CAT_CAPT_CTRL, CATC_CAP_MODE, 1)
+#define REG_CAP_NONE 0x00
+#define REG_CAP_ANTI_SHAKE 0x02
+
+#define CAPC_SEL_FRAME I2C_REG(CAT_CAPT_CTRL, CATC_CAP_SEL_FRAME, 1)
+
+#define CAPC_START I2C_REG(CAT_CAPT_CTRL, CATC_CAP_START, 1)
+#define REG_CAP_START_MAIN 0x01
+#define REG_CAP_START_THUMB 0x03
+
+#define CAPC_IMAGE_SIZE I2C_REG(CAT_CAPT_CTRL, CATC_CAP_IMAGE_SIZE, 1)
+#define CAPC_THUMB_SIZE I2C_REG(CAT_CAPT_CTRL, CATC_CAP_THUMB_SIZE, 1)
+
+/*
+ * Category F - Flash
+ *
+ * This mode provides functions about internal flash stuff and system startup.
+ */
+#define CATF_CAM_START 0x12 /* It starts internal ARM core booting
+ * after power-up */
+
+#define FLASH_CAM_START I2C_REG(CAT_FLASH, CATF_CAM_START, 1)
+#define REG_START_ARM_BOOT 0x01
+
+#endif /* M5MOLS_REG_H */
diff --git a/include/media/m5mols.h b/include/media/m5mols.h
new file mode 100644
index 0000000..2d7e7ca
--- /dev/null
+++ b/include/media/m5mols.h
@@ -0,0 +1,35 @@
+/*
+ * Driver header for M-5MOLS 8M Pixel camera sensor with ISP
+ *
+ * Copyright (C) 2011 Samsung Electronics Co., Ltd.
+ * Author: HeungJun Kim, riverful.kim@samsung.com
+ *
+ * Copyright (C) 2009 Samsung Electronics Co., Ltd.
+ * Author: Dongsoo Nathaniel Kim, dongsoo45.kim@samsung.com
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#ifndef MEDIA_M5MOLS_H
+#define MEDIA_M5MOLS_H
+
+/**
+ * struct m5mols_platform_data - platform data for M-5MOLS driver
+ * @irq: GPIO getting the irq pin of M-5MOLS
+ * @gpio_reset: GPIO driving the reset pin of M-5MOLS
+ * @reset_polarity: active state for gpio_rst pin, 0 or 1
+ * @set_power: an additional callback to the board setup code
+ * to be called after enabling and before disabling
+ * the sensor's supply regulators
+ */
+struct m5mols_platform_data {
+ int irq;
+ int gpio_reset;
+ u8 reset_polarity;
+ int (*set_power)(struct device *dev, int on);
+};
+
+#endif /* MEDIA_M5MOLS_H */