Gitiles
Code Review Sign In
gerrit-public.fairphone.software / kernel / msm-4.19 / c0b458a9463bd6be165374a8e9e3235800ee132e / . / drivers / net / wireless / realtek / rtlwifi / rtl8723ae / pwrseq.h
blob: e6c3aac3e9fd1004ac9488517f1227242bc1d193 [file] [log] [blame]
/******************************************************************************
*
* Copyright(c) 2009-2012 Realtek Corporation.
*
* This program is free software; you can redistribute it and/or modify it
* under the terms of version 2 of the GNU General Public License as
* published by the Free Software Foundation.
*
* This program is distributed in the hope that it will be useful, but WITHOUT
* ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
* FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
* more details.
*
* The full GNU General Public License is included in this distribution in the
* file called LICENSE.
*
* Contact Information:
* wlanfae <wlanfae@realtek.com>
* Realtek Corporation, No. 2, Innovation Road II, Hsinchu Science Park,
* Hsinchu 300, Taiwan.
*
* Larry Finger <Larry.Finger@lwfinger.net>
*
*****************************************************************************/
#ifndef __RTL8723E_PWRSEQ_H__
#define __RTL8723E_PWRSEQ_H__
#include "../pwrseqcmd.h"
/*
* Check document WM-20110607-Paul-RTL8723A_Power_Architecture-R02.vsd
* There are 6 HW Power States:
* 0: POFF--Power Off
* 1: PDN--Power Down
* 2: CARDEMU--Card Emulation
* 3: ACT--Active Mode
* 4: LPS--Low Power State
* 5: SUS--Suspend
*
* The transision from different states are defined below
* TRANS_CARDEMU_TO_ACT
* TRANS_ACT_TO_CARDEMU
* TRANS_CARDEMU_TO_SUS
* TRANS_SUS_TO_CARDEMU
* TRANS_CARDEMU_TO_PDN
* TRANS_ACT_TO_LPS
* TRANS_LPS_TO_ACT
*
* TRANS_END
*/
#define RTL8723A_TRANS_CARDEMU_TO_ACT_STEPS 10
#define RTL8723A_TRANS_ACT_TO_CARDEMU_STEPS 10
#define RTL8723A_TRANS_CARDEMU_TO_SUS_STEPS 10
#define RTL8723A_TRANS_SUS_TO_CARDEMU_STEPS 10
#define RTL8723A_TRANS_CARDEMU_TO_PDN_STEPS 10
#define RTL8723A_TRANS_PDN_TO_CARDEMU_STEPS 10
#define RTL8723A_TRANS_ACT_TO_LPS_STEPS 15
#define RTL8723A_TRANS_LPS_TO_ACT_STEPS 15
#define RTL8723A_TRANS_END_STEPS 1
/* format */
/* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }*/
#define RTL8723A_TRANS_CARDEMU_TO_ACT \
/* disable SW LPS 0x04[10]=0*/ \
{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\
PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(2), 0},\
/* wait till 0x04[17] = 1 power ready*/ \
{0x0006, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\
PWR_BASEADDR_MAC, PWR_CMD_POLLING, BIT(1), BIT(1)},\
/* release WLON reset 0x04[16]=1*/ \
{0x0006, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\
PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(0), BIT(0)},\
/* disable HWPDN 0x04[15]=0*/ \
{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\
PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(7), 0},\
/* disable WL suspend*/ \
{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\
PWR_BASEADDR_MAC, PWR_CMD_WRITE, (BIT(4)|BIT(3)), 0},\
/* polling until return 0*/ \
{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\
PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(0), BIT(0)},\
{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\
PWR_BASEADDR_MAC, PWR_CMD_POLLING, BIT(0), 0},
/* format */
/* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, */
#define RTL8723A_TRANS_ACT_TO_CARDEMU \
/*0x1F[7:0] = 0 turn off RF*/ \
{0x001F, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\
PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0}, \
{0x004E, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\
PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(7), 0},\
{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\
PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(1), BIT(1)}, \
{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\
PWR_BASEADDR_MAC, PWR_CMD_POLLING, BIT(1), 0},
/* format */
/* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value },*/
#define RTL8723A_TRANS_CARDEMU_TO_SUS \
/*0x04[12:11] = 2b'11 enable WL suspend for PCIe*/ \
{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK,\
PWR_BASEADDR_MAC, PWR_CMD_WRITE, \
BIT(4)|BIT(3), (BIT(4)|BIT(3))},\
/*0x04[12:11] = 2b'01 enable WL suspend*/ \
{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK| \
PWR_INTF_SDIO_MSK,\
PWR_BASEADDR_MAC, \
PWR_CMD_WRITE, \
BIT(3)|BIT(4), BIT(3)}, \
/*0x04[12:11] = 2b'11 enable WL suspend for PCIe*/ \
{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \
PWR_INTF_PCI_MSK, PWR_BASEADDR_MAC, \
PWR_CMD_WRITE, BIT(3)|BIT(4), \
BIT(3)|BIT(4)}, \
/*Set SDIO suspend local register*/ \
{0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \
PWR_INTF_SDIO_MSK, PWR_BASEADDR_SDIO,\
PWR_CMD_WRITE, BIT(0), BIT(0)}, \
/*wait power state to suspend*/ \
{0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \
PWR_INTF_SDIO_MSK, PWR_BASEADDR_SDIO,\
PWR_CMD_POLLING, BIT(1), 0},
/* format */
/* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, */
#define RTL8723A_TRANS_SUS_TO_CARDEMU \
/*Set SDIO suspend local register*/ \
{0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,\
PWR_BASEADDR_SDIO, PWR_CMD_WRITE, BIT(0), 0},\
/*wait power state to suspend*/ \
{0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,\
PWR_BASEADDR_SDIO, PWR_CMD_POLLING, BIT(1), BIT(1)},\
/*0x04[12:11] = 2b'00 disable WL suspend*/ \
{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\
PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(3)|BIT(4), 0},
/* format */
/* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, */
#define RTL8723A_TRANS_CARDEMU_TO_CARDDIS \
/*0x04[12:11] = 2b'01 enable WL suspend*/ \
{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \
PWR_INTF_USB_MSK|PWR_INTF_SDIO_MSK, \
PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(3)|BIT(4), BIT(3)}, \
/*0x04[10] = 1, enable SW LPS*/ \
{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \
PWR_INTF_PCI_MSK, PWR_BASEADDR_MAC,\
PWR_CMD_WRITE, BIT(2), BIT(2)}, \
/*Set SDIO suspend local register*/ \
{0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \
PWR_INTF_SDIO_MSK, PWR_BASEADDR_SDIO,\
PWR_CMD_WRITE, BIT(0), BIT(0)}, \
/*wait power state to suspend*/ \
{0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \
PWR_INTF_SDIO_MSK, PWR_BASEADDR_SDIO,\
PWR_CMD_POLLING, BIT(1), 0},
/* format */
/* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, */
#define RTL8723A_TRANS_CARDDIS_TO_CARDEMU\
/*Set SDIO suspend local register*/ \
{0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \
PWR_INTF_SDIO_MSK, PWR_BASEADDR_SDIO,\
PWR_CMD_WRITE, BIT(0), 0}, \
/*wait power state to suspend*/ \
{0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \
PWR_INTF_SDIO_MSK, PWR_BASEADDR_SDIO,\
PWR_CMD_POLLING, BIT(1), BIT(1)},\
/*0x04[12:11] = 2b'00 disable WL suspend*/ \
{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \
PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC,\
PWR_CMD_WRITE, BIT(3)|BIT(4), 0},\
/*PCIe DMA start*/ \
{0x0301, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \
PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC,\
PWR_CMD_WRITE, 0xFF, 0},
/* format */
/* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, */
#define RTL8723A_TRANS_CARDEMU_TO_PDN \
{0x0006, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \
PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC,\
PWR_CMD_WRITE, BIT(0), 0},/* 0x04[16] = 0*/\
{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \
PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC,\
PWR_CMD_WRITE, BIT(7), BIT(7)},/* 0x04[15] = 1*/
/* format */
/* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, */
#define RTL8723A_TRANS_PDN_TO_CARDEMU \
{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \
PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC,\
PWR_CMD_WRITE, BIT(7), 0},/* 0x04[15] = 0*/
/* format */
/* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, */
#define RTL8723A_TRANS_ACT_TO_LPS \
{0x0301, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \
PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC,\
PWR_CMD_WRITE, 0xFF, 0xFF},/*PCIe DMA stop*/ \
{0x0522, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \
PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC,\
PWR_CMD_WRITE, 0xFF, 0x7F},/*Tx Pause*/ \
/*Should be zero if no packet is transmitting*/ \
{0x05F8, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \
PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC,\
PWR_CMD_POLLING, 0xFF, 0},\
/*Should be zero if no packet is transmitting*/ \
{0x05F9, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \
PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC,\
PWR_CMD_POLLING, 0xFF, 0},\
/*Should be zero if no packet is transmitting*/ \
{0x05FA, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \
PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC,\
PWR_CMD_POLLING, 0xFF, 0},\
/*Should be zero if no packet is transmitting*/ \
{0x05FB, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \
PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC,\
PWR_CMD_POLLING, 0xFF, 0},\
/*CCK and OFDM are disabled,and clock are gated*/ \
{0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \
PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC,\
PWR_CMD_WRITE, BIT(0), 0},\
{0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \
PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC,\
PWR_CMD_DELAY, 0, PWRSEQ_DELAY_US},/*Delay 1us*/\
{0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \
PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC,\
PWR_CMD_WRITE, BIT(1), 0},/*Whole BB is reset*/ \
{0x0100, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \
PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC,\
PWR_CMD_WRITE, 0xFF, 0x3F},/*Reset MAC TRX*/ \
{0x0101, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \
PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC,\
PWR_CMD_WRITE, BIT(1), 0},/*check if removed later*/ \
/*Respond TxOK to scheduler*/ \
{0x0553, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \
PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC,\
PWR_CMD_WRITE, BIT(5), BIT(5)},\
#define RTL8723A_TRANS_LPS_TO_ACT\
/* format */ \
/* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, */ \
{0x0080, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \
PWR_INTF_SDIO_MSK, PWR_BASEADDR_SDIO,\
PWR_CMD_WRITE, 0xFF, 0x84}, /*SDIO RPWM*/\
{0xFE58, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \
PWR_INTF_USB_MSK, PWR_BASEADDR_MAC,\
PWR_CMD_WRITE, 0xFF, 0x84}, /*USB RPWM*/\
{0x0361, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \
PWR_INTF_PCI_MSK, PWR_BASEADDR_MAC,\
PWR_CMD_WRITE, 0xFF, 0x84}, /*PCIe RPWM*/\
{0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \
PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC,\
PWR_CMD_DELAY, 0, PWRSEQ_DELAY_MS}, /*Delay*/\
/*. 0x08[4] = 0 switch TSF to 40M*/\
{0x0008, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \
PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC,\
PWR_CMD_WRITE, BIT(4), 0}, \
/*Polling 0x109[7]=0 TSF in 40M*/\
{0x0109, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \
PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC,\
PWR_CMD_POLLING, BIT(7), 0}, \
/*. 0x29[7:6] = 2b'00 enable BB clock*/\
{0x0029, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \
PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC,\
PWR_CMD_WRITE, BIT(6)|BIT(7), 0},\
/*. 0x101[1] = 1*/\
{0x0101, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \
PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC,\
PWR_CMD_WRITE, BIT(1), BIT(1)},\
/*. 0x100[7:0] = 0xFF enable WMAC TRX*/\
{0x0100, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \
PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC,\
PWR_CMD_WRITE, 0xFF, 0xFF},\
/*. 0x02[1:0] = 2b'11 enable BB macro*/\
{0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \
PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC,\
PWR_CMD_WRITE, BIT(1)|BIT(0), BIT(1)|BIT(0)},\
{0x0522, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \
PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC,\
PWR_CMD_WRITE, 0xFF, 0}, /*. 0x522 = 0*/
/* format */
/* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, */
#define RTL8723A_TRANS_END \
{0xFFFF, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\
0, PWR_CMD_END, 0, 0}
extern struct wlan_pwr_cfg rtl8723A_power_on_flow
[RTL8723A_TRANS_CARDEMU_TO_ACT_STEPS +
RTL8723A_TRANS_END_STEPS];
extern struct wlan_pwr_cfg rtl8723A_radio_off_flow
[RTL8723A_TRANS_ACT_TO_CARDEMU_STEPS +
RTL8723A_TRANS_END_STEPS];
extern struct wlan_pwr_cfg rtl8723A_card_disable_flow
[RTL8723A_TRANS_ACT_TO_CARDEMU_STEPS +
RTL8723A_TRANS_CARDEMU_TO_PDN_STEPS +
RTL8723A_TRANS_END_STEPS];
extern struct wlan_pwr_cfg rtl8723A_card_enable_flow
[RTL8723A_TRANS_ACT_TO_CARDEMU_STEPS +
RTL8723A_TRANS_CARDEMU_TO_PDN_STEPS +
RTL8723A_TRANS_END_STEPS];
extern struct wlan_pwr_cfg rtl8723A_suspend_flow
[RTL8723A_TRANS_ACT_TO_CARDEMU_STEPS +
RTL8723A_TRANS_CARDEMU_TO_SUS_STEPS +
RTL8723A_TRANS_END_STEPS];
extern struct wlan_pwr_cfg rtl8723A_resume_flow
[RTL8723A_TRANS_ACT_TO_CARDEMU_STEPS +
RTL8723A_TRANS_CARDEMU_TO_SUS_STEPS +
RTL8723A_TRANS_END_STEPS];
extern struct wlan_pwr_cfg rtl8723A_hwpdn_flow
[RTL8723A_TRANS_ACT_TO_CARDEMU_STEPS +
RTL8723A_TRANS_CARDEMU_TO_PDN_STEPS +
RTL8723A_TRANS_END_STEPS];
extern struct wlan_pwr_cfg rtl8723A_enter_lps_flow
[RTL8723A_TRANS_ACT_TO_LPS_STEPS + RTL8723A_TRANS_END_STEPS];
extern struct wlan_pwr_cfg rtl8723A_leave_lps_flow
[RTL8723A_TRANS_LPS_TO_ACT_STEPS + RTL8723A_TRANS_END_STEPS];
/* RTL8723 Power Configuration CMDs for PCIe interface */
#define Rtl8723_NIC_PWR_ON_FLOW rtl8723A_power_on_flow
#define Rtl8723_NIC_RF_OFF_FLOW rtl8723A_radio_off_flow
#define Rtl8723_NIC_DISABLE_FLOW rtl8723A_card_disable_flow
#define Rtl8723_NIC_ENABLE_FLOW rtl8723A_card_enable_flow
#define Rtl8723_NIC_SUSPEND_FLOW rtl8723A_suspend_flow
#define Rtl8723_NIC_RESUME_FLOW rtl8723A_resume_flow
#define Rtl8723_NIC_PDN_FLOW rtl8723A_hwpdn_flow
#define Rtl8723_NIC_LPS_ENTER_FLOW rtl8723A_enter_lps_flow
#define Rtl8723_NIC_LPS_LEAVE_FLOW rtl8723A_leave_lps_flow
#endif