Merge tag 'armsoc-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups from Kevin Hilman:
"A relatively small setup of cleanups this time around, and similar to
last time the bulk of it is removal of legacy board support:
- OMAP: removal of legacy (non-DT) booting for several platforms
- i.MX: remove some legacy board files"
* tag 'armsoc-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (36 commits)
ARM: fix EFM32 build breakage caused by cpu_resume_arm
ARM: 8389/1: Add cpu_resume_arm() for firmwares that resume in ARM state
ARM: v7 setup function should invalidate L1 cache
mach-omap2: Remove use of deprecated marco, PTR_RET in devices.c
ARM: OMAP2+: Remove calls to deprecacted marco,PTR_RET in the files,fb.c and pmu.c
ARM: OMAP2+: Constify irq_domain_ops
ARM: OMAP2+: use symbolic defines for console loglevels instead of numbers
ARM: at91: remove useless Makefile.boot
ARM: at91: remove at91rm9200_sdramc.h
ARM: at91: remove mach/at91_ramc.h and mach/at91rm9200_mc.h
ARM: at91/pm: use the atmel-mc syscon defines
pcmcia: at91_cf: Use syscon to configure the MC/smc
ARM: at91: declare the at91rm9200 memory controller as a syscon
mfd: syscon: Add Atmel MC (Memory Controller) registers definition
ARM: at91: drop sam9_smc.c
ata: at91: use syscon to configure the smc
ARM: ux500: delete static resource defines
ARM: ux500: rename ux500_map_io
ARM: ux500: look up PRCMU resource from DT
ARM: ux500: kill off L2CC static map
...
diff --git a/Documentation/devicetree/bindings/arm/atmel-at91.txt b/Documentation/devicetree/bindings/arm/atmel-at91.txt
index 2e99b5b..424ac8c 100644
--- a/Documentation/devicetree/bindings/arm/atmel-at91.txt
+++ b/Documentation/devicetree/bindings/arm/atmel-at91.txt
@@ -98,7 +98,7 @@
};
RAMC SDRAM/DDR Controller required properties:
-- compatible: Should be "atmel,at91rm9200-sdramc",
+- compatible: Should be "atmel,at91rm9200-sdramc", "syscon"
"atmel,at91sam9260-sdramc",
"atmel,at91sam9g45-ddramc",
"atmel,sama5d3-ddramc",
diff --git a/Documentation/devicetree/bindings/fuse/nvidia,tegra20-fuse.txt b/Documentation/devicetree/bindings/fuse/nvidia,tegra20-fuse.txt
index 23e1d31..41372d4 100644
--- a/Documentation/devicetree/bindings/fuse/nvidia,tegra20-fuse.txt
+++ b/Documentation/devicetree/bindings/fuse/nvidia,tegra20-fuse.txt
@@ -29,7 +29,7 @@
fuse@7000f800 {
compatible = "nvidia,tegra20-efuse";
- reg = <0x7000F800 0x400>,
+ reg = <0x7000f800 0x400>,
<0x70000000 0x400>;
clocks = <&tegra_car TEGRA20_CLK_FUSE>;
clock-names = "fuse";
diff --git a/arch/arm/boot/dts/at91rm9200.dtsi b/arch/arm/boot/dts/at91rm9200.dtsi
index 4fb333b..6d0fa9b 100644
--- a/arch/arm/boot/dts/at91rm9200.dtsi
+++ b/arch/arm/boot/dts/at91rm9200.dtsi
@@ -92,7 +92,7 @@
};
ramc0: ramc@ffffff00 {
- compatible = "atmel,at91rm9200-sdramc";
+ compatible = "atmel,at91rm9200-sdramc", "syscon";
reg = <0xffffff00 0x100>;
};
diff --git a/arch/arm/boot/dts/exynos5260-xyref5260.dts b/arch/arm/boot/dts/exynos5260-xyref5260.dts
index a803b60..3daef94 100644
--- a/arch/arm/boot/dts/exynos5260-xyref5260.dts
+++ b/arch/arm/boot/dts/exynos5260-xyref5260.dts
@@ -70,7 +70,7 @@
broken-cd;
bypass-smu;
cap-mmc-highspeed;
- supports-hs200-mode; /* 200 Mhz */
+ supports-hs200-mode; /* 200 MHz */
card-detect-delay = <200>;
samsung,dw-mshc-ciu-div = <3>;
samsung,dw-mshc-sdr-timing = <0 4>;
diff --git a/arch/arm/boot/dts/omap3-cm-t3517.dts b/arch/arm/boot/dts/omap3-cm-t3517.dts
index f5b5a1d..53ae04f 100644
--- a/arch/arm/boot/dts/omap3-cm-t3517.dts
+++ b/arch/arm/boot/dts/omap3-cm-t3517.dts
@@ -66,7 +66,7 @@
otg_drv_vbus: pinmux_otg_drv_vbus {
pinctrl-single,pins = <
- OMAP3_CORE1_IOPAD(0x2210, PIN_INPUT_PULLDOWN | MUX_MODE0) /* rmii_50Mhz_clk.usb0_drvvbus */
+ OMAP3_CORE1_IOPAD(0x2210, PIN_INPUT_PULLDOWN | MUX_MODE0) /* rmii_50MHz_clk.usb0_drvvbus */
>;
};
diff --git a/arch/arm/boot/dts/tegra124.dtsi b/arch/arm/boot/dts/tegra124.dtsi
index 13cc7ca..4db9be0 100644
--- a/arch/arm/boot/dts/tegra124.dtsi
+++ b/arch/arm/boot/dts/tegra124.dtsi
@@ -300,7 +300,7 @@
apbmisc@0,70000800 {
compatible = "nvidia,tegra124-apbmisc", "nvidia,tegra20-apbmisc";
reg = <0x0 0x70000800 0x0 0x64>, /* Chip revision */
- <0x0 0x7000E864 0x0 0x04>; /* Strapping options */
+ <0x0 0x7000e864 0x0 0x04>; /* Strapping options */
};
pinmux: pinmux@0,70000868 {
diff --git a/arch/arm/boot/dts/tegra20.dtsi b/arch/arm/boot/dts/tegra20.dtsi
index adf6b04..f444b67 100644
--- a/arch/arm/boot/dts/tegra20.dtsi
+++ b/arch/arm/boot/dts/tegra20.dtsi
@@ -563,7 +563,7 @@
fuse@7000f800 {
compatible = "nvidia,tegra20-efuse";
- reg = <0x7000F800 0x400>;
+ reg = <0x7000f800 0x400>;
clocks = <&tegra_car TEGRA20_CLK_FUSE>;
clock-names = "fuse";
resets = <&tegra_car 39>;
diff --git a/arch/arm/include/asm/suspend.h b/arch/arm/include/asm/suspend.h
index cd20029..6c7182f 100644
--- a/arch/arm/include/asm/suspend.h
+++ b/arch/arm/include/asm/suspend.h
@@ -7,6 +7,7 @@
};
extern void cpu_resume(void);
+extern void cpu_resume_arm(void);
extern int cpu_suspend(unsigned long, int (*)(unsigned long));
#endif
diff --git a/arch/arm/kernel/sleep.S b/arch/arm/kernel/sleep.S
index 7d37bfc..6060dbc 100644
--- a/arch/arm/kernel/sleep.S
+++ b/arch/arm/kernel/sleep.S
@@ -118,6 +118,16 @@
.text
.align
+
+#ifdef CONFIG_MMU
+ .arm
+ENTRY(cpu_resume_arm)
+ THUMB( adr r9, BSYM(1f) ) @ Kernel is entered in ARM.
+ THUMB( bx r9 ) @ If this is a Thumb-2 kernel,
+ THUMB( .thumb ) @ switch to Thumb now.
+ THUMB(1: )
+#endif
+
ENTRY(cpu_resume)
ARM_BE8(setend be) @ ensure we are in BE mode
#ifdef CONFIG_ARM_VIRT_EXT
@@ -150,6 +160,10 @@
THUMB( bx r3 )
ENDPROC(cpu_resume)
+#ifdef CONFIG_MMU
+ENDPROC(cpu_resume_arm)
+#endif
+
.align 2
_sleep_save_sp:
.long sleep_save_sp - .
diff --git a/arch/arm/mach-at91/Makefile b/arch/arm/mach-at91/Makefile
index 4fa8b45..c5bbf8b 100644
--- a/arch/arm/mach-at91/Makefile
+++ b/arch/arm/mach-at91/Makefile
@@ -1,13 +1,8 @@
#
# Makefile for the linux kernel.
#
-ccflags-$(CONFIG_ARCH_MULTIPLATFORM) := -I$(srctree)/$(src)/include
-asflags-$(CONFIG_ARCH_MULTIPLATFORM) := -I$(srctree)/$(src)/include
-
obj-y := soc.o
-obj-$(CONFIG_SOC_AT91SAM9) += sam9_smc.o
-
# CPU-specific support
obj-$(CONFIG_SOC_AT91RM9200) += at91rm9200.o
obj-$(CONFIG_SOC_AT91SAM9) += at91sam9.o
diff --git a/arch/arm/mach-at91/Makefile.boot b/arch/arm/mach-at91/Makefile.boot
deleted file mode 100644
index 29ed0fa..0000000
--- a/arch/arm/mach-at91/Makefile.boot
+++ /dev/null
@@ -1,8 +0,0 @@
-# Note: the following conditions must always be true:
-# ZRELADDR == virt_to_phys(TEXTADDR)
-# PARAMS_PHYS must be within 4MB of ZRELADDR
-# INITRD_PHYS must be in RAM
-
- zreladdr-y += 0x20008000
-params_phys-y := 0x20000100
-initrd_phys-y := 0x20410000
diff --git a/arch/arm/mach-at91/include/mach/at91_ramc.h b/arch/arm/mach-at91/include/mach/at91_ramc.h
deleted file mode 100644
index 493bc48..0000000
--- a/arch/arm/mach-at91/include/mach/at91_ramc.h
+++ /dev/null
@@ -1,28 +0,0 @@
-/*
- * Header file for the Atmel RAM Controller
- *
- * Copyright (C) 2011 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
- *
- * Under GPLv2 only
- */
-
-#ifndef __AT91_RAMC_H__
-#define __AT91_RAMC_H__
-
-#ifndef __ASSEMBLY__
-extern void __iomem *at91_ramc_base[];
-
-#define at91_ramc_read(id, field) \
- __raw_readl(at91_ramc_base[id] + field)
-
-#define at91_ramc_write(id, field, value) \
- __raw_writel(value, at91_ramc_base[id] + field)
-#else
-.extern at91_ramc_base
-#endif
-
-#include <soc/at91/at91rm9200_sdramc.h>
-#include <soc/at91/at91sam9_ddrsdr.h>
-#include <soc/at91/at91sam9_sdramc.h>
-
-#endif /* __AT91_RAMC_H__ */
diff --git a/arch/arm/mach-at91/include/mach/at91rm9200_mc.h b/arch/arm/mach-at91/include/mach/at91rm9200_mc.h
deleted file mode 100644
index aeaadfb..0000000
--- a/arch/arm/mach-at91/include/mach/at91rm9200_mc.h
+++ /dev/null
@@ -1,116 +0,0 @@
-/*
- * arch/arm/mach-at91/include/mach/at91rm9200_mc.h
- *
- * Copyright (C) 2005 Ivan Kokshaysky
- * Copyright (C) SAN People
- *
- * Memory Controllers (MC, EBI, SMC, SDRAMC, BFC) - System peripherals registers.
- * Based on AT91RM9200 datasheet revision E.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- */
-
-#ifndef AT91RM9200_MC_H
-#define AT91RM9200_MC_H
-
-/* Memory Controller */
-#define AT91_MC_RCR 0x00 /* MC Remap Control Register */
-#define AT91_MC_RCB (1 << 0) /* Remap Command Bit */
-
-#define AT91_MC_ASR 0x04 /* MC Abort Status Register */
-#define AT91_MC_UNADD (1 << 0) /* Undefined Address Abort Status */
-#define AT91_MC_MISADD (1 << 1) /* Misaligned Address Abort Status */
-#define AT91_MC_ABTSZ (3 << 8) /* Abort Size Status */
-#define AT91_MC_ABTSZ_BYTE (0 << 8)
-#define AT91_MC_ABTSZ_HALFWORD (1 << 8)
-#define AT91_MC_ABTSZ_WORD (2 << 8)
-#define AT91_MC_ABTTYP (3 << 10) /* Abort Type Status */
-#define AT91_MC_ABTTYP_DATAREAD (0 << 10)
-#define AT91_MC_ABTTYP_DATAWRITE (1 << 10)
-#define AT91_MC_ABTTYP_FETCH (2 << 10)
-#define AT91_MC_MST0 (1 << 16) /* ARM920T Abort Source */
-#define AT91_MC_MST1 (1 << 17) /* PDC Abort Source */
-#define AT91_MC_MST2 (1 << 18) /* UHP Abort Source */
-#define AT91_MC_MST3 (1 << 19) /* EMAC Abort Source */
-#define AT91_MC_SVMST0 (1 << 24) /* Saved ARM920T Abort Source */
-#define AT91_MC_SVMST1 (1 << 25) /* Saved PDC Abort Source */
-#define AT91_MC_SVMST2 (1 << 26) /* Saved UHP Abort Source */
-#define AT91_MC_SVMST3 (1 << 27) /* Saved EMAC Abort Source */
-
-#define AT91_MC_AASR 0x08 /* MC Abort Address Status Register */
-
-#define AT91_MC_MPR 0x0c /* MC Master Priority Register */
-#define AT91_MPR_MSTP0 (7 << 0) /* ARM920T Priority */
-#define AT91_MPR_MSTP1 (7 << 4) /* PDC Priority */
-#define AT91_MPR_MSTP2 (7 << 8) /* UHP Priority */
-#define AT91_MPR_MSTP3 (7 << 12) /* EMAC Priority */
-
-/* External Bus Interface (EBI) registers */
-#define AT91_EBI_CSA 0x60 /* Chip Select Assignment Register */
-#define AT91_EBI_CS0A (1 << 0) /* Chip Select 0 Assignment */
-#define AT91_EBI_CS0A_SMC (0 << 0)
-#define AT91_EBI_CS0A_BFC (1 << 0)
-#define AT91_EBI_CS1A (1 << 1) /* Chip Select 1 Assignment */
-#define AT91_EBI_CS1A_SMC (0 << 1)
-#define AT91_EBI_CS1A_SDRAMC (1 << 1)
-#define AT91_EBI_CS3A (1 << 3) /* Chip Select 2 Assignment */
-#define AT91_EBI_CS3A_SMC (0 << 3)
-#define AT91_EBI_CS3A_SMC_SMARTMEDIA (1 << 3)
-#define AT91_EBI_CS4A (1 << 4) /* Chip Select 3 Assignment */
-#define AT91_EBI_CS4A_SMC (0 << 4)
-#define AT91_EBI_CS4A_SMC_COMPACTFLASH (1 << 4)
-#define AT91_EBI_CFGR (AT91_MC + 0x64) /* Configuration Register */
-#define AT91_EBI_DBPUC (1 << 0) /* Data Bus Pull-Up Configuration */
-
-/* Static Memory Controller (SMC) registers */
-#define AT91_SMC_CSR(n) (0x70 + ((n) * 4)) /* SMC Chip Select Register */
-#define AT91_SMC_NWS (0x7f << 0) /* Number of Wait States */
-#define AT91_SMC_NWS_(x) ((x) << 0)
-#define AT91_SMC_WSEN (1 << 7) /* Wait State Enable */
-#define AT91_SMC_TDF (0xf << 8) /* Data Float Time */
-#define AT91_SMC_TDF_(x) ((x) << 8)
-#define AT91_SMC_BAT (1 << 12) /* Byte Access Type */
-#define AT91_SMC_DBW (3 << 13) /* Data Bus Width */
-#define AT91_SMC_DBW_16 (1 << 13)
-#define AT91_SMC_DBW_8 (2 << 13)
-#define AT91_SMC_DPR (1 << 15) /* Data Read Protocol */
-#define AT91_SMC_ACSS (3 << 16) /* Address to Chip Select Setup */
-#define AT91_SMC_ACSS_STD (0 << 16)
-#define AT91_SMC_ACSS_1 (1 << 16)
-#define AT91_SMC_ACSS_2 (2 << 16)
-#define AT91_SMC_ACSS_3 (3 << 16)
-#define AT91_SMC_RWSETUP (7 << 24) /* Read & Write Signal Time Setup */
-#define AT91_SMC_RWSETUP_(x) ((x) << 24)
-#define AT91_SMC_RWHOLD (7 << 28) /* Read & Write Signal Hold Time */
-#define AT91_SMC_RWHOLD_(x) ((x) << 28)
-
-/* Burst Flash Controller register */
-#define AT91_BFC_MR 0xc0 /* Mode Register */
-#define AT91_BFC_BFCOM (3 << 0) /* Burst Flash Controller Operating Mode */
-#define AT91_BFC_BFCOM_DISABLED (0 << 0)
-#define AT91_BFC_BFCOM_ASYNC (1 << 0)
-#define AT91_BFC_BFCOM_BURST (2 << 0)
-#define AT91_BFC_BFCC (3 << 2) /* Burst Flash Controller Clock */
-#define AT91_BFC_BFCC_MCK (1 << 2)
-#define AT91_BFC_BFCC_DIV2 (2 << 2)
-#define AT91_BFC_BFCC_DIV4 (3 << 2)
-#define AT91_BFC_AVL (0xf << 4) /* Address Valid Latency */
-#define AT91_BFC_PAGES (7 << 8) /* Page Size */
-#define AT91_BFC_PAGES_NO_PAGE (0 << 8)
-#define AT91_BFC_PAGES_16 (1 << 8)
-#define AT91_BFC_PAGES_32 (2 << 8)
-#define AT91_BFC_PAGES_64 (3 << 8)
-#define AT91_BFC_PAGES_128 (4 << 8)
-#define AT91_BFC_PAGES_256 (5 << 8)
-#define AT91_BFC_PAGES_512 (6 << 8)
-#define AT91_BFC_PAGES_1024 (7 << 8)
-#define AT91_BFC_OEL (3 << 12) /* Output Enable Latency */
-#define AT91_BFC_BAAEN (1 << 16) /* Burst Address Advance Enable */
-#define AT91_BFC_BFOEH (1 << 17) /* Burst Flash Output Enable Handling */
-#define AT91_BFC_MUXEN (1 << 18) /* Multiplexed Bus Enable */
-#define AT91_BFC_RDYEN (1 << 19) /* Ready Enable Mode */
-
-#endif
diff --git a/arch/arm/mach-at91/include/mach/at91sam9_smc.h b/arch/arm/mach-at91/include/mach/at91sam9_smc.h
deleted file mode 100644
index ff54a0c..0000000
--- a/arch/arm/mach-at91/include/mach/at91sam9_smc.h
+++ /dev/null
@@ -1,98 +0,0 @@
-/*
- * arch/arm/mach-at91/include/mach/at91sam9_smc.h
- *
- * Copyright (C) 2007 Andrew Victor
- * Copyright (C) 2007 Atmel Corporation.
- *
- * Static Memory Controllers (SMC) - System peripherals registers.
- * Based on AT91SAM9261 datasheet revision D.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- */
-
-#ifndef AT91SAM9_SMC_H
-#define AT91SAM9_SMC_H
-
-#ifndef __ASSEMBLY__
-struct sam9_smc_config {
- /* Setup register */
- u8 ncs_read_setup;
- u8 nrd_setup;
- u8 ncs_write_setup;
- u8 nwe_setup;
-
- /* Pulse register */
- u8 ncs_read_pulse;
- u8 nrd_pulse;
- u8 ncs_write_pulse;
- u8 nwe_pulse;
-
- /* Cycle register */
- u16 read_cycle;
- u16 write_cycle;
-
- /* Mode register */
- u32 mode;
- u8 tdf_cycles:4;
-};
-
-extern void sam9_smc_configure(int id, int cs, struct sam9_smc_config *config);
-extern void sam9_smc_read(int id, int cs, struct sam9_smc_config *config);
-extern void sam9_smc_read_mode(int id, int cs, struct sam9_smc_config *config);
-extern void sam9_smc_write_mode(int id, int cs, struct sam9_smc_config *config);
-#endif
-
-#define AT91_SMC_SETUP 0x00 /* Setup Register for CS n */
-#define AT91_SMC_NWESETUP (0x3f << 0) /* NWE Setup Length */
-#define AT91_SMC_NWESETUP_(x) ((x) << 0)
-#define AT91_SMC_NCS_WRSETUP (0x3f << 8) /* NCS Setup Length in Write Access */
-#define AT91_SMC_NCS_WRSETUP_(x) ((x) << 8)
-#define AT91_SMC_NRDSETUP (0x3f << 16) /* NRD Setup Length */
-#define AT91_SMC_NRDSETUP_(x) ((x) << 16)
-#define AT91_SMC_NCS_RDSETUP (0x3f << 24) /* NCS Setup Length in Read Access */
-#define AT91_SMC_NCS_RDSETUP_(x) ((x) << 24)
-
-#define AT91_SMC_PULSE 0x04 /* Pulse Register for CS n */
-#define AT91_SMC_NWEPULSE (0x7f << 0) /* NWE Pulse Length */
-#define AT91_SMC_NWEPULSE_(x) ((x) << 0)
-#define AT91_SMC_NCS_WRPULSE (0x7f << 8) /* NCS Pulse Length in Write Access */
-#define AT91_SMC_NCS_WRPULSE_(x)((x) << 8)
-#define AT91_SMC_NRDPULSE (0x7f << 16) /* NRD Pulse Length */
-#define AT91_SMC_NRDPULSE_(x) ((x) << 16)
-#define AT91_SMC_NCS_RDPULSE (0x7f << 24) /* NCS Pulse Length in Read Access */
-#define AT91_SMC_NCS_RDPULSE_(x)((x) << 24)
-
-#define AT91_SMC_CYCLE 0x08 /* Cycle Register for CS n */
-#define AT91_SMC_NWECYCLE (0x1ff << 0 ) /* Total Write Cycle Length */
-#define AT91_SMC_NWECYCLE_(x) ((x) << 0)
-#define AT91_SMC_NRDCYCLE (0x1ff << 16) /* Total Read Cycle Length */
-#define AT91_SMC_NRDCYCLE_(x) ((x) << 16)
-
-#define AT91_SMC_MODE 0x0c /* Mode Register for CS n */
-#define AT91_SMC_READMODE (1 << 0) /* Read Mode */
-#define AT91_SMC_WRITEMODE (1 << 1) /* Write Mode */
-#define AT91_SMC_EXNWMODE (3 << 4) /* NWAIT Mode */
-#define AT91_SMC_EXNWMODE_DISABLE (0 << 4)
-#define AT91_SMC_EXNWMODE_FROZEN (2 << 4)
-#define AT91_SMC_EXNWMODE_READY (3 << 4)
-#define AT91_SMC_BAT (1 << 8) /* Byte Access Type */
-#define AT91_SMC_BAT_SELECT (0 << 8)
-#define AT91_SMC_BAT_WRITE (1 << 8)
-#define AT91_SMC_DBW (3 << 12) /* Data Bus Width */
-#define AT91_SMC_DBW_8 (0 << 12)
-#define AT91_SMC_DBW_16 (1 << 12)
-#define AT91_SMC_DBW_32 (2 << 12)
-#define AT91_SMC_TDF (0xf << 16) /* Data Float Time. */
-#define AT91_SMC_TDF_(x) ((x) << 16)
-#define AT91_SMC_TDFMODE (1 << 20) /* TDF Optimization - Enabled */
-#define AT91_SMC_PMEN (1 << 24) /* Page Mode Enabled */
-#define AT91_SMC_PS (3 << 28) /* Page Size */
-#define AT91_SMC_PS_4 (0 << 28)
-#define AT91_SMC_PS_8 (1 << 28)
-#define AT91_SMC_PS_16 (2 << 28)
-#define AT91_SMC_PS_32 (3 << 28)
-
-#endif
diff --git a/arch/arm/mach-at91/pm.c b/arch/arm/mach-at91/pm.c
index 5062699..1e18476 100644
--- a/arch/arm/mach-at91/pm.c
+++ b/arch/arm/mach-at91/pm.c
@@ -233,7 +233,7 @@
*/
static void at91rm9200_standby(void)
{
- u32 lpr = at91_ramc_read(0, AT91RM9200_SDRAMC_LPR);
+ u32 lpr = at91_ramc_read(0, AT91_MC_SDRAMC_LPR);
asm volatile(
"b 1f\n\t"
@@ -244,8 +244,8 @@
" mcr p15, 0, %0, c7, c0, 4\n\t"
" str %5, [%1, %2]"
:
- : "r" (0), "r" (at91_ramc_base[0]), "r" (AT91RM9200_SDRAMC_LPR),
- "r" (1), "r" (AT91RM9200_SDRAMC_SRR),
+ : "r" (0), "r" (at91_ramc_base[0]), "r" (AT91_MC_SDRAMC_LPR),
+ "r" (1), "r" (AT91_MC_SDRAMC_SRR),
"r" (lpr));
}
@@ -414,7 +414,7 @@
/*
* AT91RM9200 SDRAM low-power mode cannot be used with self-refresh.
*/
- at91_ramc_write(0, AT91RM9200_SDRAMC_LPR, 0);
+ at91_ramc_write(0, AT91_MC_SDRAMC_LPR, 0);
at91_pm_data.uhp_udp_mask = AT91RM9200_PMC_UHP | AT91RM9200_PMC_UDP;
at91_pm_data.memctrl = AT91_MEMCTRL_MC;
diff --git a/arch/arm/mach-at91/pm.h b/arch/arm/mach-at91/pm.h
index ecd875a..3fcf881 100644
--- a/arch/arm/mach-at91/pm.h
+++ b/arch/arm/mach-at91/pm.h
@@ -13,7 +13,19 @@
#include <asm/proc-fns.h>
-#include <mach/at91_ramc.h>
+#include <linux/mfd/syscon/atmel-mc.h>
+#include <soc/at91/at91sam9_ddrsdr.h>
+#include <soc/at91/at91sam9_sdramc.h>
+
+#ifndef __ASSEMBLY__
+extern void __iomem *at91_ramc_base[];
+
+#define at91_ramc_read(id, field) \
+ __raw_readl(at91_ramc_base[id] + field)
+
+#define at91_ramc_write(id, field, value) \
+ __raw_writel(value, at91_ramc_base[id] + field)
+#endif
#define AT91_MEMCTRL_MC 0
#define AT91_MEMCTRL_SDRAMC 1
diff --git a/arch/arm/mach-at91/pm_suspend.S b/arch/arm/mach-at91/pm_suspend.S
index bd22b2c..0d95f48 100644
--- a/arch/arm/mach-at91/pm_suspend.S
+++ b/arch/arm/mach-at91/pm_suspend.S
@@ -13,7 +13,6 @@
*/
#include <linux/linkage.h>
#include <linux/clk/at91_pmc.h>
-#include <mach/at91_ramc.h>
#include "pm.h"
#define SRAMC_SELF_FRESH_ACTIVE 0x01
@@ -216,7 +215,7 @@
/* Active SDRAM self-refresh mode */
mov r3, #1
- str r3, [r2, #AT91RM9200_SDRAMC_SRR]
+ str r3, [r2, #AT91_MC_SDRAMC_SRR]
b exit_sramc_sf
ddrc_sf:
diff --git a/arch/arm/mach-at91/sam9_smc.c b/arch/arm/mach-at91/sam9_smc.c
deleted file mode 100644
index 826315a..0000000
--- a/arch/arm/mach-at91/sam9_smc.c
+++ /dev/null
@@ -1,136 +0,0 @@
-/*
- * linux/arch/arm/mach-at91/sam9_smc.c
- *
- * Copyright (C) 2008 Andrew Victor
- * Copyright (C) 2011 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-
-#include <linux/module.h>
-#include <linux/io.h>
-#include <linux/of.h>
-#include <linux/of_address.h>
-
-#include <mach/at91sam9_smc.h>
-
-#include "sam9_smc.h"
-
-
-#define AT91_SMC_CS(id, n) (smc_base_addr[id] + ((n) * 0x10))
-
-static void __iomem *smc_base_addr[2];
-
-static void sam9_smc_cs_write_mode(void __iomem *base,
- struct sam9_smc_config *config)
-{
- __raw_writel(config->mode
- | AT91_SMC_TDF_(config->tdf_cycles),
- base + AT91_SMC_MODE);
-}
-
-void sam9_smc_write_mode(int id, int cs,
- struct sam9_smc_config *config)
-{
- sam9_smc_cs_write_mode(AT91_SMC_CS(id, cs), config);
-}
-EXPORT_SYMBOL_GPL(sam9_smc_write_mode);
-
-static void sam9_smc_cs_configure(void __iomem *base,
- struct sam9_smc_config *config)
-{
-
- /* Setup register */
- __raw_writel(AT91_SMC_NWESETUP_(config->nwe_setup)
- | AT91_SMC_NCS_WRSETUP_(config->ncs_write_setup)
- | AT91_SMC_NRDSETUP_(config->nrd_setup)
- | AT91_SMC_NCS_RDSETUP_(config->ncs_read_setup),
- base + AT91_SMC_SETUP);
-
- /* Pulse register */
- __raw_writel(AT91_SMC_NWEPULSE_(config->nwe_pulse)
- | AT91_SMC_NCS_WRPULSE_(config->ncs_write_pulse)
- | AT91_SMC_NRDPULSE_(config->nrd_pulse)
- | AT91_SMC_NCS_RDPULSE_(config->ncs_read_pulse),
- base + AT91_SMC_PULSE);
-
- /* Cycle register */
- __raw_writel(AT91_SMC_NWECYCLE_(config->write_cycle)
- | AT91_SMC_NRDCYCLE_(config->read_cycle),
- base + AT91_SMC_CYCLE);
-
- /* Mode register */
- sam9_smc_cs_write_mode(base, config);
-}
-
-void sam9_smc_configure(int id, int cs,
- struct sam9_smc_config *config)
-{
- sam9_smc_cs_configure(AT91_SMC_CS(id, cs), config);
-}
-EXPORT_SYMBOL_GPL(sam9_smc_configure);
-
-static void sam9_smc_cs_read_mode(void __iomem *base,
- struct sam9_smc_config *config)
-{
- u32 val = __raw_readl(base + AT91_SMC_MODE);
-
- config->mode = (val & ~AT91_SMC_NWECYCLE);
- config->tdf_cycles = (val & AT91_SMC_NWECYCLE) >> 16 ;
-}
-
-void sam9_smc_read_mode(int id, int cs,
- struct sam9_smc_config *config)
-{
- sam9_smc_cs_read_mode(AT91_SMC_CS(id, cs), config);
-}
-EXPORT_SYMBOL_GPL(sam9_smc_read_mode);
-
-static void sam9_smc_cs_read(void __iomem *base,
- struct sam9_smc_config *config)
-{
- u32 val;
-
- /* Setup register */
- val = __raw_readl(base + AT91_SMC_SETUP);
-
- config->nwe_setup = val & AT91_SMC_NWESETUP;
- config->ncs_write_setup = (val & AT91_SMC_NCS_WRSETUP) >> 8;
- config->nrd_setup = (val & AT91_SMC_NRDSETUP) >> 16;
- config->ncs_read_setup = (val & AT91_SMC_NCS_RDSETUP) >> 24;
-
- /* Pulse register */
- val = __raw_readl(base + AT91_SMC_PULSE);
-
- config->nwe_pulse = val & AT91_SMC_NWEPULSE;
- config->ncs_write_pulse = (val & AT91_SMC_NCS_WRPULSE) >> 8;
- config->nrd_pulse = (val & AT91_SMC_NRDPULSE) >> 16;
- config->ncs_read_pulse = (val & AT91_SMC_NCS_RDPULSE) >> 24;
-
- /* Cycle register */
- val = __raw_readl(base + AT91_SMC_CYCLE);
-
- config->write_cycle = val & AT91_SMC_NWECYCLE;
- config->read_cycle = (val & AT91_SMC_NRDCYCLE) >> 16;
-
- /* Mode register */
- sam9_smc_cs_read_mode(base, config);
-}
-
-void sam9_smc_read(int id, int cs, struct sam9_smc_config *config)
-{
- sam9_smc_cs_read(AT91_SMC_CS(id, cs), config);
-}
-
-void __init at91sam9_ioremap_smc(int id, u32 addr)
-{
- if (id > 1) {
- pr_warn("%s: id > 2\n", __func__);
- return;
- }
- smc_base_addr[id] = ioremap(addr, 512);
- if (!smc_base_addr[id])
- pr_warn("Impossible to ioremap smc.%d 0x%x\n", id, addr);
-}
diff --git a/arch/arm/mach-at91/sam9_smc.h b/arch/arm/mach-at91/sam9_smc.h
deleted file mode 100644
index 3e52dcd4..0000000
--- a/arch/arm/mach-at91/sam9_smc.h
+++ /dev/null
@@ -1,11 +0,0 @@
-/*
- * linux/arch/arm/mach-at91/sam9_smc.
- *
- * Copyright (C) 2008 Andrew Victor
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-
-extern void __init at91sam9_ioremap_smc(int id, u32 addr);
diff --git a/arch/arm/mach-bcm/Makefile b/arch/arm/mach-bcm/Makefile
index 4c38674..54d274d 100644
--- a/arch/arm/mach-bcm/Makefile
+++ b/arch/arm/mach-bcm/Makefile
@@ -43,5 +43,5 @@
ifeq ($(CONFIG_ARCH_BRCMSTB),y)
CFLAGS_platsmp-brcmstb.o += -march=armv7-a
obj-y += brcmstb.o
-obj-$(CONFIG_SMP) += headsmp-brcmstb.o platsmp-brcmstb.o
+obj-$(CONFIG_SMP) += platsmp-brcmstb.o
endif
diff --git a/arch/arm/mach-bcm/brcmstb.h b/arch/arm/mach-bcm/brcmstb.h
deleted file mode 100644
index ec0c3d1..0000000
--- a/arch/arm/mach-bcm/brcmstb.h
+++ /dev/null
@@ -1,19 +0,0 @@
-/*
- * Copyright (C) 2013-2014 Broadcom Corporation
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation version 2.
- *
- * This program is distributed "as is" WITHOUT ANY WARRANTY of any
- * kind, whether express or implied; without even the implied warranty
- * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- */
-
-#ifndef __BRCMSTB_H__
-#define __BRCMSTB_H__
-
-void brcmstb_secondary_startup(void);
-
-#endif /* __BRCMSTB_H__ */
diff --git a/arch/arm/mach-bcm/headsmp-brcmstb.S b/arch/arm/mach-bcm/headsmp-brcmstb.S
deleted file mode 100644
index 199c1ea..0000000
--- a/arch/arm/mach-bcm/headsmp-brcmstb.S
+++ /dev/null
@@ -1,33 +0,0 @@
-/*
- * SMP boot code for secondary CPUs
- * Based on arch/arm/mach-tegra/headsmp.S
- *
- * Copyright (C) 2010 NVIDIA, Inc.
- * Copyright (C) 2013-2014 Broadcom Corporation
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation version 2.
- *
- * This program is distributed "as is" WITHOUT ANY WARRANTY of any
- * kind, whether express or implied; without even the implied warranty
- * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- */
-
-#include <asm/assembler.h>
-#include <linux/linkage.h>
-#include <linux/init.h>
-
- .section ".text.head", "ax"
-
-ENTRY(brcmstb_secondary_startup)
- /*
- * Ensure CPU is in a sane state by disabling all IRQs and switching
- * into SVC mode.
- */
- setmode PSR_I_BIT | PSR_F_BIT | SVC_MODE, r0
-
- bl v7_invalidate_l1
- b secondary_startup
-ENDPROC(brcmstb_secondary_startup)
diff --git a/arch/arm/mach-bcm/platsmp-brcmstb.c b/arch/arm/mach-bcm/platsmp-brcmstb.c
index e209e6f..44d6bddf 100644
--- a/arch/arm/mach-bcm/platsmp-brcmstb.c
+++ b/arch/arm/mach-bcm/platsmp-brcmstb.c
@@ -30,8 +30,6 @@
#include <asm/mach-types.h>
#include <asm/smp_plat.h>
-#include "brcmstb.h"
-
enum {
ZONE_MAN_CLKEN_MASK = BIT(0),
ZONE_MAN_RESET_CNTL_MASK = BIT(1),
@@ -153,7 +151,7 @@
* Set the reset vector to point to the secondary_startup
* routine
*/
- cpu_set_boot_addr(cpu, virt_to_phys(brcmstb_secondary_startup));
+ cpu_set_boot_addr(cpu, virt_to_phys(secondary_startup));
/* Unhalt the cpu */
cpu_rst_cfg_set(cpu, 0);
diff --git a/arch/arm/mach-berlin/headsmp.S b/arch/arm/mach-berlin/headsmp.S
index 4a4c56a..dc82a34 100644
--- a/arch/arm/mach-berlin/headsmp.S
+++ b/arch/arm/mach-berlin/headsmp.S
@@ -12,12 +12,6 @@
#include <linux/init.h>
#include <asm/assembler.h>
-ENTRY(berlin_secondary_startup)
- ARM_BE8(setend be)
- bl v7_invalidate_l1
- b secondary_startup
-ENDPROC(berlin_secondary_startup)
-
/*
* If the following instruction is set in the reset exception vector, CPUs
* will fetch the value of the software reset address vector when being
diff --git a/arch/arm/mach-berlin/platsmp.c b/arch/arm/mach-berlin/platsmp.c
index 702e798..34a3753 100644
--- a/arch/arm/mach-berlin/platsmp.c
+++ b/arch/arm/mach-berlin/platsmp.c
@@ -22,7 +22,6 @@
#define RESET_VECT 0x00
#define SW_RESET_ADDR 0x94
-extern void berlin_secondary_startup(void);
extern u32 boot_inst;
static void __iomem *cpu_ctrl;
@@ -85,7 +84,7 @@
* Write the secondary startup address into the SW reset address
* vector. This is used by boot_inst.
*/
- writel(virt_to_phys(berlin_secondary_startup), vectors_base + SW_RESET_ADDR);
+ writel(virt_to_phys(secondary_startup), vectors_base + SW_RESET_ADDR);
iounmap(vectors_base);
unmap_scu:
diff --git a/arch/arm/mach-davinci/include/mach/da8xx.h b/arch/arm/mach-davinci/include/mach/da8xx.h
index 39e58b4..f9f9713 100644
--- a/arch/arm/mach-davinci/include/mach/da8xx.h
+++ b/arch/arm/mach-davinci/include/mach/da8xx.h
@@ -36,7 +36,7 @@
/*
* If the DA850/OMAP-L138/AM18x SoC on board is of a higher speed grade
- * (than the regular 300Mhz variant), the board code should set this up
+ * (than the regular 300MHz variant), the board code should set this up
* with the supported speed before calling da850_register_cpufreq().
*/
extern unsigned int da850_max_speed;
diff --git a/arch/arm/mach-hisi/Makefile b/arch/arm/mach-hisi/Makefile
index 6b7b303..659db19 100644
--- a/arch/arm/mach-hisi/Makefile
+++ b/arch/arm/mach-hisi/Makefile
@@ -6,4 +6,4 @@
obj-y += hisilicon.o
obj-$(CONFIG_MCPM) += platmcpm.o
-obj-$(CONFIG_SMP) += platsmp.o hotplug.o headsmp.o
+obj-$(CONFIG_SMP) += platsmp.o hotplug.o
diff --git a/arch/arm/mach-hisi/core.h b/arch/arm/mach-hisi/core.h
index 92a682d..c7648ef 100644
--- a/arch/arm/mach-hisi/core.h
+++ b/arch/arm/mach-hisi/core.h
@@ -12,7 +12,6 @@
extern int hi3xxx_cpu_kill(unsigned int cpu);
extern void hi3xxx_set_cpu(int cpu, bool enable);
-extern void hisi_secondary_startup(void);
extern struct smp_operations hix5hd2_smp_ops;
extern void hix5hd2_set_cpu(int cpu, bool enable);
extern void hix5hd2_cpu_die(unsigned int cpu);
diff --git a/arch/arm/mach-hisi/headsmp.S b/arch/arm/mach-hisi/headsmp.S
deleted file mode 100644
index 81e35b1..0000000
--- a/arch/arm/mach-hisi/headsmp.S
+++ /dev/null
@@ -1,16 +0,0 @@
-/*
- * Copyright (c) 2014 Hisilicon Limited.
- * Copyright (c) 2014 Linaro Ltd.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-#include <linux/linkage.h>
-#include <linux/init.h>
-
- __CPUINIT
-
-ENTRY(hisi_secondary_startup)
- bl v7_invalidate_l1
- b secondary_startup
diff --git a/arch/arm/mach-hisi/platsmp.c b/arch/arm/mach-hisi/platsmp.c
index 8880c8e..5174412 100644
--- a/arch/arm/mach-hisi/platsmp.c
+++ b/arch/arm/mach-hisi/platsmp.c
@@ -118,7 +118,7 @@
{
phys_addr_t jumpaddr;
- jumpaddr = virt_to_phys(hisi_secondary_startup);
+ jumpaddr = virt_to_phys(secondary_startup);
hix5hd2_set_scu_boot_addr(HIX5HD2_BOOT_ADDRESS, jumpaddr);
hix5hd2_set_cpu(cpu, true);
arch_send_wakeup_ipi_mask(cpumask_of(cpu));
@@ -156,7 +156,7 @@
struct device_node *node;
- jumpaddr = virt_to_phys(hisi_secondary_startup);
+ jumpaddr = virt_to_phys(secondary_startup);
hip01_set_boot_addr(HIP01_BOOT_ADDRESS, jumpaddr);
node = of_find_compatible_node(NULL, NULL, "hisilicon,hip01-sysctrl");
diff --git a/arch/arm/mach-imx/Kconfig b/arch/arm/mach-imx/Kconfig
index 3a3d3e9..388232c 100644
--- a/arch/arm/mach-imx/Kconfig
+++ b/arch/arm/mach-imx/Kconfig
@@ -444,40 +444,6 @@
Include support for MX35PDK platform. This includes specific
configurations for the board and its peripherals.
-config MACH_EUKREA_CPUIMX35SD
- bool "Support Eukrea CPUIMX35 Platform"
- select IMX_HAVE_PLATFORM_FLEXCAN
- select IMX_HAVE_PLATFORM_FSL_USB2_UDC
- select IMX_HAVE_PLATFORM_IMX2_WDT
- select IMX_HAVE_PLATFORM_IMX_I2C
- select IMX_HAVE_PLATFORM_IMX_UART
- select IMX_HAVE_PLATFORM_MXC_EHCI
- select IMX_HAVE_PLATFORM_MXC_NAND
- select IMX_HAVE_PLATFORM_SDHCI_ESDHC_IMX
- select USB_ULPI_VIEWPORT if USB_ULPI
- select SOC_IMX35
- help
- Include support for Eukrea CPUIMX35 platform. This includes
- specific configurations for the board and its peripherals.
-
-choice
- prompt "Baseboard"
- depends on MACH_EUKREA_CPUIMX35SD
- default MACH_EUKREA_MBIMXSD35_BASEBOARD
-
-config MACH_EUKREA_MBIMXSD35_BASEBOARD
- bool "Eukrea MBIMXSD development board"
- select IMX_HAVE_PLATFORM_GPIO_KEYS
- select IMX_HAVE_PLATFORM_IMX_SSI
- select IMX_HAVE_PLATFORM_IPU_CORE
- select IMX_HAVE_PLATFORM_SPI_IMX
- select LEDS_GPIO_REGISTER
- help
- This adds board specific devices that can be found on Eukrea's
- MBIMXSD evaluation board.
-
-endchoice
-
config MACH_VPR200
bool "Support VPR200 platform"
select IMX_HAVE_PLATFORM_FSL_USB2_UDC
diff --git a/arch/arm/mach-imx/Makefile b/arch/arm/mach-imx/Makefile
index 3244cf1..eed6098 100644
--- a/arch/arm/mach-imx/Makefile
+++ b/arch/arm/mach-imx/Makefile
@@ -73,8 +73,6 @@
# i.MX35 based machines
obj-$(CONFIG_MACH_PCM043) += mach-pcm043.o
obj-$(CONFIG_MACH_MX35_3DS) += mach-mx35_3ds.o
-obj-$(CONFIG_MACH_EUKREA_CPUIMX35SD) += mach-cpuimx35.o
-obj-$(CONFIG_MACH_EUKREA_MBIMXSD35_BASEBOARD) += eukrea_mbimxsd35-baseboard.o
obj-$(CONFIG_MACH_VPR200) += mach-vpr200.o
obj-$(CONFIG_MACH_IMX35_DT) += imx35-dt.o
diff --git a/arch/arm/mach-imx/clk-imx6sx.c b/arch/arm/mach-imx/clk-imx6sx.c
index 5a3e5a1..87c5b09 100644
--- a/arch/arm/mach-imx/clk-imx6sx.c
+++ b/arch/arm/mach-imx/clk-imx6sx.c
@@ -216,7 +216,7 @@
clks[IMX6SX_CLK_USBPHY1_GATE] = imx_clk_gate("usbphy1_gate", "dummy", base + 0x10, 6);
clks[IMX6SX_CLK_USBPHY2_GATE] = imx_clk_gate("usbphy2_gate", "dummy", base + 0x20, 6);
- /* FIXME 100Mhz is used for pcie ref for all imx6 pcie, excepted imx6q */
+ /* FIXME 100MHz is used for pcie ref for all imx6 pcie, excepted imx6q */
clks[IMX6SX_CLK_PCIE_REF] = imx_clk_fixed_factor("pcie_ref", "pll6_enet", 1, 5);
clks[IMX6SX_CLK_PCIE_REF_125M] = imx_clk_gate("pcie_ref_125m", "pcie_ref", base + 0xe0, 19);
@@ -520,7 +520,7 @@
pr_err("Failed to set pcie parent clk.\n");
/*
- * Init enet system AHB clock, set to 200Mhz
+ * Init enet system AHB clock, set to 200MHz
* pll2_pfd2_396m-> ENET_PODF-> ENET_AHB
*/
clk_set_parent(clks[IMX6SX_CLK_ENET_PRE_SEL], clks[IMX6SX_CLK_PLL2_PFD2]);
diff --git a/arch/arm/mach-imx/eukrea_mbimxsd35-baseboard.c b/arch/arm/mach-imx/eukrea_mbimxsd35-baseboard.c
deleted file mode 100644
index 6edc940..0000000
--- a/arch/arm/mach-imx/eukrea_mbimxsd35-baseboard.c
+++ /dev/null
@@ -1,318 +0,0 @@
-/*
- * Copyright (C) 2010 Eric Benard - eric@eukrea.com
- *
- * Based on pcm970-baseboard.c which is :
- * Copyright (C) 2008 Juergen Beisert (kernel@pengutronix.de)
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License
- * as published by the Free Software Foundation; either version 2
- * of the License, or (at your option) any later version.
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
- * MA 02110-1301, USA.
- */
-
-#include <linux/types.h>
-#include <linux/init.h>
-
-#include <linux/gpio.h>
-#include <linux/interrupt.h>
-#include <linux/leds.h>
-#include <linux/platform_device.h>
-#include <linux/input.h>
-#include <linux/spi/spi.h>
-#include <video/platform_lcd.h>
-#include <linux/i2c.h>
-
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-#include <asm/mach/time.h>
-#include <asm/mach/map.h>
-
-#include "common.h"
-#include "devices-imx35.h"
-#include "hardware.h"
-#include "iomux-mx35.h"
-
-static const struct fb_videomode fb_modedb[] = {
- {
- .name = "CMO-QVGA",
- .refresh = 60,
- .xres = 320,
- .yres = 240,
- .pixclock = KHZ2PICOS(6500),
- .left_margin = 68,
- .right_margin = 20,
- .upper_margin = 15,
- .lower_margin = 4,
- .hsync_len = 30,
- .vsync_len = 3,
- .sync = 0,
- .vmode = FB_VMODE_NONINTERLACED,
- .flag = 0,
- },
- {
- .name = "DVI-VGA",
- .refresh = 60,
- .xres = 640,
- .yres = 480,
- .pixclock = 32000,
- .left_margin = 100,
- .right_margin = 100,
- .upper_margin = 7,
- .lower_margin = 100,
- .hsync_len = 7,
- .vsync_len = 7,
- .sync = FB_SYNC_VERT_HIGH_ACT | FB_SYNC_HOR_HIGH_ACT |
- FB_SYNC_OE_ACT_HIGH | FB_SYNC_CLK_INVERT,
- .vmode = FB_VMODE_NONINTERLACED,
- .flag = 0,
- },
- {
- .name = "DVI-SVGA",
- .refresh = 60,
- .xres = 800,
- .yres = 600,
- .pixclock = 25000,
- .left_margin = 75,
- .right_margin = 75,
- .upper_margin = 7,
- .lower_margin = 75,
- .hsync_len = 7,
- .vsync_len = 7,
- .sync = FB_SYNC_VERT_HIGH_ACT | FB_SYNC_HOR_HIGH_ACT |
- FB_SYNC_OE_ACT_HIGH | FB_SYNC_CLK_INVERT,
- .vmode = FB_VMODE_NONINTERLACED,
- .flag = 0,
- },
-};
-
-static struct mx3fb_platform_data mx3fb_pdata __initdata = {
- .name = "CMO-QVGA",
- .mode = fb_modedb,
- .num_modes = ARRAY_SIZE(fb_modedb),
-};
-
-static const iomux_v3_cfg_t eukrea_mbimxsd_pads[] __initconst = {
- /* LCD */
- MX35_PAD_LD0__IPU_DISPB_DAT_0,
- MX35_PAD_LD1__IPU_DISPB_DAT_1,
- MX35_PAD_LD2__IPU_DISPB_DAT_2,
- MX35_PAD_LD3__IPU_DISPB_DAT_3,
- MX35_PAD_LD4__IPU_DISPB_DAT_4,
- MX35_PAD_LD5__IPU_DISPB_DAT_5,
- MX35_PAD_LD6__IPU_DISPB_DAT_6,
- MX35_PAD_LD7__IPU_DISPB_DAT_7,
- MX35_PAD_LD8__IPU_DISPB_DAT_8,
- MX35_PAD_LD9__IPU_DISPB_DAT_9,
- MX35_PAD_LD10__IPU_DISPB_DAT_10,
- MX35_PAD_LD11__IPU_DISPB_DAT_11,
- MX35_PAD_LD12__IPU_DISPB_DAT_12,
- MX35_PAD_LD13__IPU_DISPB_DAT_13,
- MX35_PAD_LD14__IPU_DISPB_DAT_14,
- MX35_PAD_LD15__IPU_DISPB_DAT_15,
- MX35_PAD_LD16__IPU_DISPB_DAT_16,
- MX35_PAD_LD17__IPU_DISPB_DAT_17,
- MX35_PAD_D3_HSYNC__IPU_DISPB_D3_HSYNC,
- MX35_PAD_D3_FPSHIFT__IPU_DISPB_D3_CLK,
- MX35_PAD_D3_DRDY__IPU_DISPB_D3_DRDY,
- MX35_PAD_D3_VSYNC__IPU_DISPB_D3_VSYNC,
- /* Backlight */
- MX35_PAD_CONTRAST__IPU_DISPB_CONTR,
- /* LCD_PWR */
- MX35_PAD_D3_CLS__GPIO1_4,
- /* LED */
- MX35_PAD_LD23__GPIO3_29,
- /* SWITCH */
- MX35_PAD_LD19__GPIO3_25,
- /* UART2 */
- MX35_PAD_CTS2__UART2_CTS,
- MX35_PAD_RTS2__UART2_RTS,
- MX35_PAD_TXD2__UART2_TXD_MUX,
- MX35_PAD_RXD2__UART2_RXD_MUX,
- /* I2S */
- MX35_PAD_STXFS4__AUDMUX_AUD4_TXFS,
- MX35_PAD_STXD4__AUDMUX_AUD4_TXD,
- MX35_PAD_SRXD4__AUDMUX_AUD4_RXD,
- MX35_PAD_SCK4__AUDMUX_AUD4_TXC,
- /* CAN2 */
- MX35_PAD_TX5_RX0__CAN2_TXCAN,
- MX35_PAD_TX4_RX1__CAN2_RXCAN,
- /* SDCARD */
- MX35_PAD_SD1_CMD__ESDHC1_CMD,
- MX35_PAD_SD1_CLK__ESDHC1_CLK,
- MX35_PAD_SD1_DATA0__ESDHC1_DAT0,
- MX35_PAD_SD1_DATA1__ESDHC1_DAT1,
- MX35_PAD_SD1_DATA2__ESDHC1_DAT2,
- MX35_PAD_SD1_DATA3__ESDHC1_DAT3,
- /* SD1 CD */
- MX35_PAD_LD18__GPIO3_24,
- /* SPI */
- MX35_PAD_CSPI1_MOSI__CSPI1_MOSI,
- MX35_PAD_CSPI1_MISO__CSPI1_MISO,
- MX35_PAD_CSPI1_SS0__GPIO1_18,
- MX35_PAD_CSPI1_SS1__GPIO1_19,
- MX35_PAD_CSPI1_SCLK__CSPI1_SCLK,
- MX35_PAD_CSPI1_SPI_RDY__GPIO3_5,
-};
-
-#define GPIO_LED1 IMX_GPIO_NR(3, 29)
-#define GPIO_SWITCH1 IMX_GPIO_NR(3, 25)
-#define GPIO_LCDPWR IMX_GPIO_NR(1, 4)
-#define GPIO_SD1CD IMX_GPIO_NR(3, 24)
-#define GPIO_SPI1_SS0 IMX_GPIO_NR(1, 18)
-#define GPIO_SPI1_SS1 IMX_GPIO_NR(1, 19)
-#define GPIO_SPI1_IRQ IMX_GPIO_NR(3, 5)
-
-static void eukrea_mbimxsd_lcd_power_set(struct plat_lcd_data *pd,
- unsigned int power)
-{
- if (power)
- gpio_direction_output(GPIO_LCDPWR, 1);
- else
- gpio_direction_output(GPIO_LCDPWR, 0);
-}
-
-static struct plat_lcd_data eukrea_mbimxsd_lcd_power_data = {
- .set_power = eukrea_mbimxsd_lcd_power_set,
-};
-
-static struct platform_device eukrea_mbimxsd_lcd_powerdev = {
- .name = "platform-lcd",
- .dev.platform_data = &eukrea_mbimxsd_lcd_power_data,
-};
-
-static struct gpio_led eukrea_mbimxsd_leds[] = {
- {
- .name = "led1",
- .default_trigger = "heartbeat",
- .active_low = 1,
- .gpio = GPIO_LED1,
- },
-};
-
-static const struct gpio_led_platform_data
- eukrea_mbimxsd_led_info __initconst = {
- .leds = eukrea_mbimxsd_leds,
- .num_leds = ARRAY_SIZE(eukrea_mbimxsd_leds),
-};
-
-static struct gpio_keys_button eukrea_mbimxsd_gpio_buttons[] = {
- {
- .gpio = GPIO_SWITCH1,
- .code = BTN_0,
- .desc = "BP1",
- .active_low = 1,
- .wakeup = 1,
- },
-};
-
-static const struct gpio_keys_platform_data
- eukrea_mbimxsd_button_data __initconst = {
- .buttons = eukrea_mbimxsd_gpio_buttons,
- .nbuttons = ARRAY_SIZE(eukrea_mbimxsd_gpio_buttons),
-};
-
-static struct platform_device *platform_devices[] __initdata = {
- &eukrea_mbimxsd_lcd_powerdev,
-};
-
-static const struct imxuart_platform_data uart_pdata __initconst = {
- .flags = IMXUART_HAVE_RTSCTS,
-};
-
-static struct i2c_board_info eukrea_mbimxsd_i2c_devices[] = {
- {
- I2C_BOARD_INFO("tlv320aic23", 0x1a),
- },
-};
-
-static const
-struct imx_ssi_platform_data eukrea_mbimxsd_ssi_pdata __initconst = {
- .flags = IMX_SSI_SYN | IMX_SSI_NET | IMX_SSI_USE_I2S_SLAVE,
-};
-
-static struct esdhc_platform_data sd1_pdata = {
- .cd_gpio = GPIO_SD1CD,
- .cd_type = ESDHC_CD_GPIO,
- .wp_type = ESDHC_WP_NONE,
-};
-
-static struct spi_board_info eukrea_mbimxsd35_spi_board_info[] __initdata = {
- {
- .modalias = "spidev",
- .max_speed_hz = 20000000,
- .bus_num = 0,
- .chip_select = 0,
- .mode = SPI_MODE_0,
- },
- {
- .modalias = "spidev",
- .max_speed_hz = 20000000,
- .bus_num = 0,
- .chip_select = 1,
- .mode = SPI_MODE_0,
- },
-};
-
-static int eukrea_mbimxsd35_spi_cs[] = {GPIO_SPI1_SS0, GPIO_SPI1_SS1};
-
-static const struct spi_imx_master eukrea_mbimxsd35_spi0_data __initconst = {
- .chipselect = eukrea_mbimxsd35_spi_cs,
- .num_chipselect = ARRAY_SIZE(eukrea_mbimxsd35_spi_cs),
-};
-
-/*
- * system init for baseboard usage. Will be called by cpuimx35 init.
- *
- * Add platform devices present on this baseboard and init
- * them from CPU side as far as required to use them later on
- */
-void __init eukrea_mbimxsd35_baseboard_init(void)
-{
- if (mxc_iomux_v3_setup_multiple_pads(eukrea_mbimxsd_pads,
- ARRAY_SIZE(eukrea_mbimxsd_pads)))
- printk(KERN_ERR "error setting mbimxsd pads !\n");
-
- imx35_add_imx_uart1(&uart_pdata);
- imx35_add_ipu_core();
- imx35_add_mx3_sdc_fb(&mx3fb_pdata);
-
- imx35_add_imx_ssi(0, &eukrea_mbimxsd_ssi_pdata);
-
- imx35_add_flexcan1();
- imx35_add_sdhci_esdhc_imx(0, &sd1_pdata);
-
- gpio_request(GPIO_LED1, "LED1");
- gpio_direction_output(GPIO_LED1, 1);
- gpio_free(GPIO_LED1);
-
- gpio_request(GPIO_SWITCH1, "SWITCH1");
- gpio_direction_input(GPIO_SWITCH1);
- gpio_free(GPIO_SWITCH1);
-
- gpio_request(GPIO_LCDPWR, "LCDPWR");
- gpio_direction_output(GPIO_LCDPWR, 1);
-
- i2c_register_board_info(0, eukrea_mbimxsd_i2c_devices,
- ARRAY_SIZE(eukrea_mbimxsd_i2c_devices));
-
- gpio_request(GPIO_SPI1_IRQ, "SPI1_IRQ");
- gpio_direction_input(GPIO_SPI1_IRQ);
- gpio_free(GPIO_SPI1_IRQ);
- imx35_add_spi_imx0(&eukrea_mbimxsd35_spi0_data);
- spi_register_board_info(eukrea_mbimxsd35_spi_board_info,
- ARRAY_SIZE(eukrea_mbimxsd35_spi_board_info));
-
- platform_add_devices(platform_devices, ARRAY_SIZE(platform_devices));
- gpio_led_register_device(-1, &eukrea_mbimxsd_led_info);
- imx_add_gpio_keys(&eukrea_mbimxsd_button_data);
- imx_add_platform_device("eukrea_tlv320", 0, NULL, 0, NULL, 0);
-}
diff --git a/arch/arm/mach-imx/gpc.c b/arch/arm/mach-imx/gpc.c
index 6d0893a..0ea77ed 100644
--- a/arch/arm/mach-imx/gpc.c
+++ b/arch/arm/mach-imx/gpc.c
@@ -474,7 +474,6 @@
static struct platform_driver imx_gpc_driver = {
.driver = {
.name = "imx-gpc",
- .owner = THIS_MODULE,
.of_match_table = imx_gpc_dt_ids,
},
.probe = imx_gpc_probe,
diff --git a/arch/arm/mach-imx/headsmp.S b/arch/arm/mach-imx/headsmp.S
index de5047c..b5e9768 100644
--- a/arch/arm/mach-imx/headsmp.S
+++ b/arch/arm/mach-imx/headsmp.S
@@ -25,7 +25,6 @@
.endm
ENTRY(v7_secondary_startup)
- bl v7_invalidate_l1
set_diag_reg
b secondary_startup
ENDPROC(v7_secondary_startup)
diff --git a/arch/arm/mach-imx/mach-cpuimx35.c b/arch/arm/mach-imx/mach-cpuimx35.c
deleted file mode 100644
index 922ffd6..0000000
--- a/arch/arm/mach-imx/mach-cpuimx35.c
+++ /dev/null
@@ -1,206 +0,0 @@
-/*
- * Copyright (C) 2010 Eric Benard - eric@eukrea.com
- * Copyright (C) 2009 Sascha Hauer, Pengutronix
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
- */
-
-#include <linux/types.h>
-#include <linux/init.h>
-
-#include <linux/platform_device.h>
-#include <linux/mtd/physmap.h>
-#include <linux/memory.h>
-#include <linux/gpio.h>
-#include <linux/interrupt.h>
-#include <linux/delay.h>
-#include <linux/i2c.h>
-#include <linux/i2c/tsc2007.h>
-#include <linux/usb/otg.h>
-#include <linux/usb/ulpi.h>
-#include <linux/i2c-gpio.h>
-
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-#include <asm/mach/time.h>
-#include <asm/mach/map.h>
-
-#include "common.h"
-#include "devices-imx35.h"
-#include "ehci.h"
-#include "eukrea-baseboards.h"
-#include "hardware.h"
-#include "iomux-mx35.h"
-
-static const struct imxuart_platform_data uart_pdata __initconst = {
- .flags = IMXUART_HAVE_RTSCTS,
-};
-
-static const struct imxi2c_platform_data
- eukrea_cpuimx35_i2c0_data __initconst = {
- .bitrate = 100000,
-};
-
-#define TSC2007_IRQGPIO IMX_GPIO_NR(3, 2)
-static int tsc2007_get_pendown_state(struct device *dev)
-{
- return !gpio_get_value(TSC2007_IRQGPIO);
-}
-
-static struct tsc2007_platform_data tsc2007_info = {
- .model = 2007,
- .x_plate_ohms = 180,
- .get_pendown_state = tsc2007_get_pendown_state,
-};
-
-static struct i2c_board_info eukrea_cpuimx35_i2c_devices[] = {
- {
- I2C_BOARD_INFO("pcf8563", 0x51),
- }, {
- I2C_BOARD_INFO("tsc2007", 0x48),
- .platform_data = &tsc2007_info,
- /* irq number is run-time assigned */
- },
-};
-
-static const iomux_v3_cfg_t eukrea_cpuimx35_pads[] __initconst = {
- /* UART1 */
- MX35_PAD_CTS1__UART1_CTS,
- MX35_PAD_RTS1__UART1_RTS,
- MX35_PAD_TXD1__UART1_TXD_MUX,
- MX35_PAD_RXD1__UART1_RXD_MUX,
- /* FEC */
- MX35_PAD_FEC_TX_CLK__FEC_TX_CLK,
- MX35_PAD_FEC_RX_CLK__FEC_RX_CLK,
- MX35_PAD_FEC_RX_DV__FEC_RX_DV,
- MX35_PAD_FEC_COL__FEC_COL,
- MX35_PAD_FEC_RDATA0__FEC_RDATA_0,
- MX35_PAD_FEC_TDATA0__FEC_TDATA_0,
- MX35_PAD_FEC_TX_EN__FEC_TX_EN,
- MX35_PAD_FEC_MDC__FEC_MDC,
- MX35_PAD_FEC_MDIO__FEC_MDIO,
- MX35_PAD_FEC_TX_ERR__FEC_TX_ERR,
- MX35_PAD_FEC_RX_ERR__FEC_RX_ERR,
- MX35_PAD_FEC_CRS__FEC_CRS,
- MX35_PAD_FEC_RDATA1__FEC_RDATA_1,
- MX35_PAD_FEC_TDATA1__FEC_TDATA_1,
- MX35_PAD_FEC_RDATA2__FEC_RDATA_2,
- MX35_PAD_FEC_TDATA2__FEC_TDATA_2,
- MX35_PAD_FEC_RDATA3__FEC_RDATA_3,
- MX35_PAD_FEC_TDATA3__FEC_TDATA_3,
- /* I2C1 */
- MX35_PAD_I2C1_CLK__I2C1_SCL,
- MX35_PAD_I2C1_DAT__I2C1_SDA,
- /* TSC2007 IRQ */
- MX35_PAD_ATA_DA2__GPIO3_2,
-};
-
-static const struct mxc_nand_platform_data
- eukrea_cpuimx35_nand_board_info __initconst = {
- .width = 1,
- .hw_ecc = 1,
- .flash_bbt = 1,
-};
-
-static int eukrea_cpuimx35_otg_init(struct platform_device *pdev)
-{
- return mx35_initialize_usb_hw(pdev->id, MXC_EHCI_INTERFACE_DIFF_UNI);
-}
-
-static const struct mxc_usbh_platform_data otg_pdata __initconst = {
- .init = eukrea_cpuimx35_otg_init,
- .portsc = MXC_EHCI_MODE_UTMI,
-};
-
-static int eukrea_cpuimx35_usbh1_init(struct platform_device *pdev)
-{
- return mx35_initialize_usb_hw(pdev->id, MXC_EHCI_INTERFACE_SINGLE_UNI |
- MXC_EHCI_INTERNAL_PHY | MXC_EHCI_IPPUE_DOWN);
-}
-
-static const struct mxc_usbh_platform_data usbh1_pdata __initconst = {
- .init = eukrea_cpuimx35_usbh1_init,
- .portsc = MXC_EHCI_MODE_SERIAL,
-};
-
-static const struct fsl_usb2_platform_data otg_device_pdata __initconst = {
- .operating_mode = FSL_USB2_DR_DEVICE,
- .phy_mode = FSL_USB2_PHY_UTMI,
- .workaround = FLS_USB2_WORKAROUND_ENGCM09152,
-};
-
-static bool otg_mode_host __initdata;
-
-static int __init eukrea_cpuimx35_otg_mode(char *options)
-{
- if (!strcmp(options, "host"))
- otg_mode_host = true;
- else if (!strcmp(options, "device"))
- otg_mode_host = false;
- else
- pr_info("otg_mode neither \"host\" nor \"device\". "
- "Defaulting to device\n");
- return 1;
-}
-__setup("otg_mode=", eukrea_cpuimx35_otg_mode);
-
-/*
- * Board specific initialization.
- */
-static void __init eukrea_cpuimx35_init(void)
-{
- imx35_soc_init();
-
- mxc_iomux_v3_setup_multiple_pads(eukrea_cpuimx35_pads,
- ARRAY_SIZE(eukrea_cpuimx35_pads));
-
- imx35_add_fec(NULL);
- imx35_add_imx2_wdt();
-
- imx35_add_imx_uart0(&uart_pdata);
- imx35_add_mxc_nand(&eukrea_cpuimx35_nand_board_info);
-
- eukrea_cpuimx35_i2c_devices[1].irq = gpio_to_irq(TSC2007_IRQGPIO);
- i2c_register_board_info(0, eukrea_cpuimx35_i2c_devices,
- ARRAY_SIZE(eukrea_cpuimx35_i2c_devices));
- imx35_add_imx_i2c0(&eukrea_cpuimx35_i2c0_data);
-
- if (otg_mode_host)
- imx35_add_mxc_ehci_otg(&otg_pdata);
- else
- imx35_add_fsl_usb2_udc(&otg_device_pdata);
-
- imx35_add_mxc_ehci_hs(&usbh1_pdata);
-
-#ifdef CONFIG_MACH_EUKREA_MBIMXSD35_BASEBOARD
- eukrea_mbimxsd35_baseboard_init();
-#endif
-}
-
-static void __init eukrea_cpuimx35_timer_init(void)
-{
- mx35_clocks_init();
-}
-
-MACHINE_START(EUKREA_CPUIMX35SD, "Eukrea CPUIMX35")
- /* Maintainer: Eukrea Electromatique */
- .atag_offset = 0x100,
- .map_io = mx35_map_io,
- .init_early = imx35_init_early,
- .init_irq = mx35_init_irq,
- .init_time = eukrea_cpuimx35_timer_init,
- .init_machine = eukrea_cpuimx35_init,
- .restart = mxc_restart,
-MACHINE_END
diff --git a/arch/arm/mach-iop13xx/include/mach/time.h b/arch/arm/mach-iop13xx/include/mach/time.h
index 15bc9bb..c871e68 100644
--- a/arch/arm/mach-iop13xx/include/mach/time.h
+++ b/arch/arm/mach-iop13xx/include/mach/time.h
@@ -42,7 +42,7 @@
case IOP13XX_CORE_FREQ_1200:
return 1200000000;
default:
- printk("%s: warning unknown frequency, defaulting to 800Mhz\n",
+ printk("%s: warning unknown frequency, defaulting to 800MHz\n",
__func__);
}
diff --git a/arch/arm/mach-ixp4xx/include/mach/platform.h b/arch/arm/mach-ixp4xx/include/mach/platform.h
index 75c4c65..34b3d3f 100644
--- a/arch/arm/mach-ixp4xx/include/mach/platform.h
+++ b/arch/arm/mach-ixp4xx/include/mach/platform.h
@@ -74,7 +74,7 @@
/*
* Clock Speed Definitions.
*/
-#define IXP4XX_PERIPHERAL_BUS_CLOCK (66) /* 66Mhzi APB BUS */
+#define IXP4XX_PERIPHERAL_BUS_CLOCK (66) /* 66MHzi APB BUS */
#define IXP4XX_UART_XTAL 14745600
/*
diff --git a/arch/arm/mach-ks8695/include/mach/hardware.h b/arch/arm/mach-ks8695/include/mach/hardware.h
index 5090338..959c748 100644
--- a/arch/arm/mach-ks8695/include/mach/hardware.h
+++ b/arch/arm/mach-ks8695/include/mach/hardware.h
@@ -17,7 +17,7 @@
#include <asm/sizes.h>
/*
- * Clocks are derived from MCLK, which is 25Mhz
+ * Clocks are derived from MCLK, which is 25MHz
*/
#define KS8695_CLOCK_RATE 25000000
diff --git a/arch/arm/mach-mvebu/headsmp-a9.S b/arch/arm/mach-mvebu/headsmp-a9.S
index 08d5ed4..48e4c4b 100644
--- a/arch/arm/mach-mvebu/headsmp-a9.S
+++ b/arch/arm/mach-mvebu/headsmp-a9.S
@@ -21,7 +21,6 @@
ENTRY(mvebu_cortex_a9_secondary_startup)
ARM_BE8(setend be)
- bl v7_invalidate_l1
bl armada_38x_scu_power_up
b secondary_startup
ENDPROC(mvebu_cortex_a9_secondary_startup)
diff --git a/arch/arm/mach-omap2/Kconfig b/arch/arm/mach-omap2/Kconfig
index 6468f15..ecc04ff 100644
--- a/arch/arm/mach-omap2/Kconfig
+++ b/arch/arm/mach-omap2/Kconfig
@@ -171,12 +171,6 @@
depends on ARCH_OMAP2 && SOC_OMAP2420
default y if MACH_NOKIA_N8X0
-config MACH_OMAP3_BEAGLE
- bool "OMAP3 BEAGLE board"
- depends on ARCH_OMAP3
- default y
- select OMAP_PACKAGE_CBB
-
config MACH_OMAP_LDP
bool "OMAP3 LDP board"
depends on ARCH_OMAP3
@@ -203,12 +197,6 @@
for full description please see the products webpage at
http://www.logicpd.com/products/development-kits/zoom-omap35x-torpedo-development-kit
-config MACH_OVERO
- bool "Gumstix Overo board"
- depends on ARCH_OMAP3
- default y
- select OMAP_PACKAGE_CBB
-
config MACH_OMAP3517EVM
bool "OMAP3517/ AM3517 EVM board"
depends on ARCH_OMAP3
@@ -240,16 +228,6 @@
default y
select OMAP_PACKAGE_CBB
-config MACH_CM_T35
- bool "CompuLab CM-T35/CM-T3730 modules"
- depends on ARCH_OMAP3
- default y
- select MACH_CM_T3730
- select OMAP_PACKAGE_CUS
-
-config MACH_CM_T3730
- bool
-
config OMAP3_SDRC_AC_TIMING
bool "Enable SDRC AC timing register changes"
depends on ARCH_OMAP3
diff --git a/arch/arm/mach-omap2/Makefile b/arch/arm/mach-omap2/Makefile
index ec002bd..f1a68c6 100644
--- a/arch/arm/mach-omap2/Makefile
+++ b/arch/arm/mach-omap2/Makefile
@@ -242,17 +242,14 @@
# Specific board support
obj-$(CONFIG_MACH_OMAP_GENERIC) += board-generic.o pdata-quirks.o
-obj-$(CONFIG_MACH_OMAP3_BEAGLE) += board-omap3beagle.o
obj-$(CONFIG_MACH_OMAP_LDP) += board-ldp.o
obj-$(CONFIG_MACH_OMAP3530_LV_SOM) += board-omap3logic.o
obj-$(CONFIG_MACH_OMAP3_TORPEDO) += board-omap3logic.o
-obj-$(CONFIG_MACH_OVERO) += board-overo.o
obj-$(CONFIG_MACH_OMAP3_PANDORA) += board-omap3pandora.o
obj-$(CONFIG_MACH_NOKIA_N8X0) += board-n8x0.o
obj-$(CONFIG_MACH_NOKIA_RX51) += board-rx51.o sdram-nokia.o
obj-$(CONFIG_MACH_NOKIA_RX51) += board-rx51-peripherals.o
obj-$(CONFIG_MACH_NOKIA_RX51) += board-rx51-video.o
-obj-$(CONFIG_MACH_CM_T35) += board-cm-t35.o
# Platform specific device init code
diff --git a/arch/arm/mach-omap2/board-cm-t35.c b/arch/arm/mach-omap2/board-cm-t35.c
deleted file mode 100644
index b5dfbc1..0000000
--- a/arch/arm/mach-omap2/board-cm-t35.c
+++ /dev/null
@@ -1,769 +0,0 @@
-/*
- * CompuLab CM-T35/CM-T3730 modules support
- *
- * Copyright (C) 2009-2011 CompuLab, Ltd.
- * Authors: Mike Rapoport <mike@compulab.co.il>
- * Igor Grinberg <grinberg@compulab.co.il>
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License
- * version 2 as published by the Free Software Foundation.
- *
- * This program is distributed in the hope that it will be useful, but
- * WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
- * General Public License for more details.
- *
- */
-
-#include <linux/clk-provider.h>
-#include <linux/clkdev.h>
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/platform_device.h>
-#include <linux/input.h>
-#include <linux/input/matrix_keypad.h>
-#include <linux/delay.h>
-#include <linux/gpio.h>
-#include <linux/omap-gpmc.h>
-#include <linux/platform_data/gpio-omap.h>
-
-#include <linux/platform_data/at24.h>
-#include <linux/i2c/twl.h>
-#include <linux/regulator/fixed.h>
-#include <linux/regulator/machine.h>
-#include <linux/mmc/host.h>
-#include <linux/usb/phy.h>
-
-#include <linux/spi/spi.h>
-#include <linux/spi/tdo24m.h>
-
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-#include <asm/mach/map.h>
-
-#include <linux/platform_data/mtd-nand-omap2.h>
-#include <video/omapdss.h>
-#include <video/omap-panel-data.h>
-#include <linux/platform_data/spi-omap2-mcspi.h>
-
-#include "common.h"
-#include "mux.h"
-#include "sdram-micron-mt46h32m32lf-6.h"
-#include "hsmmc.h"
-#include "common-board-devices.h"
-
-#define CM_T35_GPIO_PENDOWN 57
-#define SB_T35_USB_HUB_RESET_GPIO 167
-
-#define CM_T35_SMSC911X_CS 5
-#define CM_T35_SMSC911X_GPIO 163
-#define SB_T35_SMSC911X_CS 4
-#define SB_T35_SMSC911X_GPIO 65
-
-#if defined(CONFIG_SMSC911X) || defined(CONFIG_SMSC911X_MODULE)
-#include <linux/smsc911x.h>
-#include "gpmc-smsc911x.h"
-
-static struct omap_smsc911x_platform_data cm_t35_smsc911x_cfg = {
- .id = 0,
- .cs = CM_T35_SMSC911X_CS,
- .gpio_irq = CM_T35_SMSC911X_GPIO,
- .gpio_reset = -EINVAL,
- .flags = SMSC911X_USE_32BIT | SMSC911X_SAVE_MAC_ADDRESS,
-};
-
-static struct omap_smsc911x_platform_data sb_t35_smsc911x_cfg = {
- .id = 1,
- .cs = SB_T35_SMSC911X_CS,
- .gpio_irq = SB_T35_SMSC911X_GPIO,
- .gpio_reset = -EINVAL,
- .flags = SMSC911X_USE_32BIT | SMSC911X_SAVE_MAC_ADDRESS,
-};
-
-static struct regulator_consumer_supply cm_t35_smsc911x_supplies[] = {
- REGULATOR_SUPPLY("vddvario", "smsc911x.0"),
- REGULATOR_SUPPLY("vdd33a", "smsc911x.0"),
-};
-
-static struct regulator_consumer_supply sb_t35_smsc911x_supplies[] = {
- REGULATOR_SUPPLY("vddvario", "smsc911x.1"),
- REGULATOR_SUPPLY("vdd33a", "smsc911x.1"),
-};
-
-static void __init cm_t35_init_ethernet(void)
-{
- regulator_register_fixed(0, cm_t35_smsc911x_supplies,
- ARRAY_SIZE(cm_t35_smsc911x_supplies));
- regulator_register_fixed(1, sb_t35_smsc911x_supplies,
- ARRAY_SIZE(sb_t35_smsc911x_supplies));
-
- gpmc_smsc911x_init(&cm_t35_smsc911x_cfg);
- gpmc_smsc911x_init(&sb_t35_smsc911x_cfg);
-}
-#else
-static inline void __init cm_t35_init_ethernet(void) { return; }
-#endif
-
-#if defined(CONFIG_LEDS_GPIO) || defined(CONFIG_LEDS_GPIO_MODULE)
-#include <linux/leds.h>
-
-static struct gpio_led cm_t35_leds[] = {
- [0] = {
- .gpio = 186,
- .name = "cm-t35:green",
- .default_trigger = "heartbeat",
- .active_low = 0,
- },
-};
-
-static struct gpio_led_platform_data cm_t35_led_pdata = {
- .num_leds = ARRAY_SIZE(cm_t35_leds),
- .leds = cm_t35_leds,
-};
-
-static struct platform_device cm_t35_led_device = {
- .name = "leds-gpio",
- .id = -1,
- .dev = {
- .platform_data = &cm_t35_led_pdata,
- },
-};
-
-static void __init cm_t35_init_led(void)
-{
- platform_device_register(&cm_t35_led_device);
-}
-#else
-static inline void cm_t35_init_led(void) {}
-#endif
-
-#if defined(CONFIG_MTD_NAND_OMAP2) || defined(CONFIG_MTD_NAND_OMAP2_MODULE)
-#include <linux/mtd/mtd.h>
-#include <linux/mtd/nand.h>
-#include <linux/mtd/partitions.h>
-
-static struct mtd_partition cm_t35_nand_partitions[] = {
- {
- .name = "xloader",
- .offset = 0, /* Offset = 0x00000 */
- .size = 4 * NAND_BLOCK_SIZE,
- .mask_flags = MTD_WRITEABLE
- },
- {
- .name = "uboot",
- .offset = MTDPART_OFS_APPEND, /* Offset = 0x80000 */
- .size = 15 * NAND_BLOCK_SIZE,
- },
- {
- .name = "uboot environment",
- .offset = MTDPART_OFS_APPEND, /* Offset = 0x260000 */
- .size = 2 * NAND_BLOCK_SIZE,
- },
- {
- .name = "linux",
- .offset = MTDPART_OFS_APPEND, /* Offset = 0x2A0000 */
- .size = 32 * NAND_BLOCK_SIZE,
- },
- {
- .name = "rootfs",
- .offset = MTDPART_OFS_APPEND, /* Offset = 0x6A0000 */
- .size = MTDPART_SIZ_FULL,
- },
-};
-
-static struct omap_nand_platform_data cm_t35_nand_data = {
- .parts = cm_t35_nand_partitions,
- .nr_parts = ARRAY_SIZE(cm_t35_nand_partitions),
- .cs = 0,
-};
-
-static void __init cm_t35_init_nand(void)
-{
- if (gpmc_nand_init(&cm_t35_nand_data, NULL) < 0)
- pr_err("CM-T35: Unable to register NAND device\n");
-}
-#else
-static inline void cm_t35_init_nand(void) {}
-#endif
-
-#define CM_T35_LCD_EN_GPIO 157
-#define CM_T35_LCD_BL_GPIO 58
-#define CM_T35_DVI_EN_GPIO 54
-
-static const struct display_timing cm_t35_lcd_videomode = {
- .pixelclock = { 0, 26000000, 0 },
-
- .hactive = { 0, 480, 0 },
- .hfront_porch = { 0, 104, 0 },
- .hback_porch = { 0, 8, 0 },
- .hsync_len = { 0, 8, 0 },
-
- .vactive = { 0, 640, 0 },
- .vfront_porch = { 0, 4, 0 },
- .vback_porch = { 0, 2, 0 },
- .vsync_len = { 0, 2, 0 },
-
- .flags = DISPLAY_FLAGS_HSYNC_LOW | DISPLAY_FLAGS_VSYNC_LOW |
- DISPLAY_FLAGS_DE_HIGH | DISPLAY_FLAGS_PIXDATA_NEGEDGE,
-};
-
-static struct panel_dpi_platform_data cm_t35_lcd_pdata = {
- .name = "lcd",
- .source = "dpi.0",
-
- .data_lines = 18,
-
- .display_timing = &cm_t35_lcd_videomode,
-
- .enable_gpio = -1,
- .backlight_gpio = CM_T35_LCD_BL_GPIO,
-};
-
-static struct platform_device cm_t35_lcd_device = {
- .name = "panel-dpi",
- .id = 0,
- .dev.platform_data = &cm_t35_lcd_pdata,
-};
-
-static struct connector_dvi_platform_data cm_t35_dvi_connector_pdata = {
- .name = "dvi",
- .source = "tfp410.0",
- .i2c_bus_num = -1,
-};
-
-static struct platform_device cm_t35_dvi_connector_device = {
- .name = "connector-dvi",
- .id = 0,
- .dev.platform_data = &cm_t35_dvi_connector_pdata,
-};
-
-static struct encoder_tfp410_platform_data cm_t35_tfp410_pdata = {
- .name = "tfp410.0",
- .source = "dpi.0",
- .data_lines = 24,
- .power_down_gpio = CM_T35_DVI_EN_GPIO,
-};
-
-static struct platform_device cm_t35_tfp410_device = {
- .name = "tfp410",
- .id = 0,
- .dev.platform_data = &cm_t35_tfp410_pdata,
-};
-
-static struct connector_atv_platform_data cm_t35_tv_pdata = {
- .name = "tv",
- .source = "venc.0",
- .connector_type = OMAP_DSS_VENC_TYPE_SVIDEO,
- .invert_polarity = false,
-};
-
-static struct platform_device cm_t35_tv_connector_device = {
- .name = "connector-analog-tv",
- .id = 0,
- .dev.platform_data = &cm_t35_tv_pdata,
-};
-
-static struct omap_dss_board_info cm_t35_dss_data = {
- .default_display_name = "dvi",
-};
-
-static struct omap2_mcspi_device_config tdo24m_mcspi_config = {
- .turbo_mode = 0,
-};
-
-static struct tdo24m_platform_data tdo24m_config = {
- .model = TDO35S,
-};
-
-static struct spi_board_info cm_t35_lcd_spi_board_info[] __initdata = {
- {
- .modalias = "tdo24m",
- .bus_num = 4,
- .chip_select = 0,
- .max_speed_hz = 1000000,
- .controller_data = &tdo24m_mcspi_config,
- .platform_data = &tdo24m_config,
- },
-};
-
-static void __init cm_t35_init_display(void)
-{
- int err;
-
- spi_register_board_info(cm_t35_lcd_spi_board_info,
- ARRAY_SIZE(cm_t35_lcd_spi_board_info));
-
-
- err = gpio_request_one(CM_T35_LCD_EN_GPIO, GPIOF_OUT_INIT_LOW,
- "lcd bl enable");
- if (err) {
- pr_err("CM-T35: failed to request LCD EN GPIO\n");
- return;
- }
-
- msleep(50);
- gpio_set_value(CM_T35_LCD_EN_GPIO, 1);
-
- err = omap_display_init(&cm_t35_dss_data);
- if (err) {
- pr_err("CM-T35: failed to register DSS device\n");
- gpio_free(CM_T35_LCD_EN_GPIO);
- }
-
- platform_device_register(&cm_t35_tfp410_device);
- platform_device_register(&cm_t35_dvi_connector_device);
- platform_device_register(&cm_t35_lcd_device);
- platform_device_register(&cm_t35_tv_connector_device);
-}
-
-static struct regulator_consumer_supply cm_t35_vmmc1_supply[] = {
- REGULATOR_SUPPLY("vmmc", "omap_hsmmc.0"),
-};
-
-static struct regulator_consumer_supply cm_t35_vsim_supply[] = {
- REGULATOR_SUPPLY("vmmc_aux", "omap_hsmmc.0"),
-};
-
-static struct regulator_consumer_supply cm_t35_vio_supplies[] = {
- REGULATOR_SUPPLY("vcc", "spi1.0"),
- REGULATOR_SUPPLY("vdds_dsi", "omapdss"),
- REGULATOR_SUPPLY("vdds_dsi", "omapdss_dpi.0"),
- REGULATOR_SUPPLY("vdds_dsi", "omapdss_dsi.0"),
-};
-
-/* VMMC1 for MMC1 pins CMD, CLK, DAT0..DAT3 (20 mA, plus card == max 220 mA) */
-static struct regulator_init_data cm_t35_vmmc1 = {
- .constraints = {
- .min_uV = 1850000,
- .max_uV = 3150000,
- .valid_modes_mask = REGULATOR_MODE_NORMAL
- | REGULATOR_MODE_STANDBY,
- .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE
- | REGULATOR_CHANGE_MODE
- | REGULATOR_CHANGE_STATUS,
- },
- .num_consumer_supplies = ARRAY_SIZE(cm_t35_vmmc1_supply),
- .consumer_supplies = cm_t35_vmmc1_supply,
-};
-
-/* VSIM for MMC1 pins DAT4..DAT7 (2 mA, plus card == max 50 mA) */
-static struct regulator_init_data cm_t35_vsim = {
- .constraints = {
- .min_uV = 1800000,
- .max_uV = 3000000,
- .valid_modes_mask = REGULATOR_MODE_NORMAL
- | REGULATOR_MODE_STANDBY,
- .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE
- | REGULATOR_CHANGE_MODE
- | REGULATOR_CHANGE_STATUS,
- },
- .num_consumer_supplies = ARRAY_SIZE(cm_t35_vsim_supply),
- .consumer_supplies = cm_t35_vsim_supply,
-};
-
-static struct regulator_init_data cm_t35_vio = {
- .constraints = {
- .min_uV = 1800000,
- .max_uV = 1800000,
- .apply_uV = true,
- .valid_modes_mask = REGULATOR_MODE_NORMAL
- | REGULATOR_MODE_STANDBY,
- .valid_ops_mask = REGULATOR_CHANGE_MODE,
- },
- .num_consumer_supplies = ARRAY_SIZE(cm_t35_vio_supplies),
- .consumer_supplies = cm_t35_vio_supplies,
-};
-
-static uint32_t cm_t35_keymap[] = {
- KEY(0, 0, KEY_A), KEY(0, 1, KEY_B), KEY(0, 2, KEY_LEFT),
- KEY(1, 0, KEY_UP), KEY(1, 1, KEY_ENTER), KEY(1, 2, KEY_DOWN),
- KEY(2, 0, KEY_RIGHT), KEY(2, 1, KEY_C), KEY(2, 2, KEY_D),
-};
-
-static struct matrix_keymap_data cm_t35_keymap_data = {
- .keymap = cm_t35_keymap,
- .keymap_size = ARRAY_SIZE(cm_t35_keymap),
-};
-
-static struct twl4030_keypad_data cm_t35_kp_data = {
- .keymap_data = &cm_t35_keymap_data,
- .rows = 3,
- .cols = 3,
- .rep = 1,
-};
-
-static struct omap2_hsmmc_info mmc[] = {
- {
- .mmc = 1,
- .caps = MMC_CAP_4_BIT_DATA,
- .gpio_cd = -EINVAL,
- .gpio_wp = -EINVAL,
- .deferred = true,
- },
- {
- .mmc = 2,
- .caps = MMC_CAP_4_BIT_DATA,
- .transceiver = 1,
- .gpio_cd = -EINVAL,
- .gpio_wp = -EINVAL,
- .ocr_mask = 0x00100000, /* 3.3V */
- },
- {} /* Terminator */
-};
-
-static struct usbhs_phy_data phy_data[] __initdata = {
- {
- .port = 1,
- .reset_gpio = OMAP_MAX_GPIO_LINES + 6,
- .vcc_gpio = -EINVAL,
- },
- {
- .port = 2,
- .reset_gpio = OMAP_MAX_GPIO_LINES + 7,
- .vcc_gpio = -EINVAL,
- },
-};
-
-static struct usbhs_omap_platform_data usbhs_bdata __initdata = {
- .port_mode[0] = OMAP_EHCI_PORT_MODE_PHY,
- .port_mode[1] = OMAP_EHCI_PORT_MODE_PHY,
-};
-
-static void __init cm_t35_init_usbh(void)
-{
- int err;
-
- err = gpio_request_one(SB_T35_USB_HUB_RESET_GPIO,
- GPIOF_OUT_INIT_LOW, "usb hub rst");
- if (err) {
- pr_err("SB-T35: usb hub rst gpio request failed: %d\n", err);
- } else {
- udelay(10);
- gpio_set_value(SB_T35_USB_HUB_RESET_GPIO, 1);
- msleep(1);
- }
-
- usbhs_init_phys(phy_data, ARRAY_SIZE(phy_data));
- usbhs_init(&usbhs_bdata);
-}
-
-static int cm_t35_twl_gpio_setup(struct device *dev, unsigned gpio,
- unsigned ngpio)
-{
- int wlan_rst = gpio + 2;
-
- if (gpio_request_one(wlan_rst, GPIOF_OUT_INIT_HIGH, "WLAN RST") == 0) {
- gpio_export(wlan_rst, 0);
- udelay(10);
- gpio_set_value_cansleep(wlan_rst, 0);
- udelay(10);
- gpio_set_value_cansleep(wlan_rst, 1);
- } else {
- pr_err("CM-T35: could not obtain gpio for WiFi reset\n");
- }
-
- /* gpio + 0 is "mmc0_cd" (input/IRQ) */
- mmc[0].gpio_cd = gpio + 0;
- omap_hsmmc_late_init(mmc);
-
- return 0;
-}
-
-static struct twl4030_gpio_platform_data cm_t35_gpio_data = {
- .setup = cm_t35_twl_gpio_setup,
-};
-
-static struct twl4030_power_data cm_t35_power_data = {
- .use_poweroff = true,
-};
-
-static struct twl4030_platform_data cm_t35_twldata = {
- /* platform_data for children goes here */
- .keypad = &cm_t35_kp_data,
- .gpio = &cm_t35_gpio_data,
- .vmmc1 = &cm_t35_vmmc1,
- .vsim = &cm_t35_vsim,
- .vio = &cm_t35_vio,
- .power = &cm_t35_power_data,
-};
-
-#if defined(CONFIG_VIDEO_OMAP3) || defined(CONFIG_VIDEO_OMAP3_MODULE)
-#include <media/omap3isp.h>
-#include "devices.h"
-
-static struct isp_platform_subdev cm_t35_isp_subdevs[] = {
- {
- .board_info = &(struct i2c_board_info){
- I2C_BOARD_INFO("mt9t001", 0x5d)
- },
- .i2c_adapter_id = 3,
- .bus = &(struct isp_bus_cfg){
- .interface = ISP_INTERFACE_PARALLEL,
- .bus = {
- .parallel = {
- .clk_pol = 1,
- },
- },
- },
- },
- {
- .board_info = &(struct i2c_board_info){
- I2C_BOARD_INFO("tvp5150", 0x5c),
- },
- .i2c_adapter_id = 3,
- .bus = &(struct isp_bus_cfg){
- .interface = ISP_INTERFACE_PARALLEL,
- .bus = {
- .parallel = {
- .clk_pol = 0,
- },
- },
- },
- },
- { 0 },
-};
-
-static struct isp_platform_data cm_t35_isp_pdata = {
- .subdevs = cm_t35_isp_subdevs,
-};
-
-static struct regulator_consumer_supply cm_t35_camera_supplies[] = {
- REGULATOR_SUPPLY("vaa", "3-005d"),
- REGULATOR_SUPPLY("vdd", "3-005d"),
-};
-
-static void __init cm_t35_init_camera(void)
-{
- struct clk *clk;
-
- clk = clk_register_fixed_rate(NULL, "mt9t001-clkin", NULL, CLK_IS_ROOT,
- 48000000);
- clk_register_clkdev(clk, NULL, "3-005d");
-
- regulator_register_fixed(2, cm_t35_camera_supplies,
- ARRAY_SIZE(cm_t35_camera_supplies));
-
- if (omap3_init_camera(&cm_t35_isp_pdata) < 0)
- pr_warn("CM-T3x: Failed registering camera device!\n");
-}
-
-#else
-static inline void cm_t35_init_camera(void) {}
-#endif /* CONFIG_VIDEO_OMAP3 */
-
-static void __init cm_t35_init_i2c(void)
-{
- omap3_pmic_get_config(&cm_t35_twldata, TWL_COMMON_PDATA_USB,
- TWL_COMMON_REGULATOR_VDAC |
- TWL_COMMON_PDATA_AUDIO);
-
- omap3_pmic_init("tps65930", &cm_t35_twldata);
-
- omap_register_i2c_bus(3, 400, NULL, 0);
-}
-
-#ifdef CONFIG_OMAP_MUX
-static struct omap_board_mux board_mux[] __initdata = {
- /* nCS and IRQ for CM-T35 ethernet */
- OMAP3_MUX(GPMC_NCS5, OMAP_MUX_MODE0),
- OMAP3_MUX(UART3_CTS_RCTX, OMAP_MUX_MODE4 | OMAP_PIN_INPUT_PULLUP),
-
- /* nCS and IRQ for SB-T35 ethernet */
- OMAP3_MUX(GPMC_NCS4, OMAP_MUX_MODE0),
- OMAP3_MUX(GPMC_WAIT3, OMAP_MUX_MODE4 | OMAP_PIN_INPUT_PULLUP),
-
- /* PENDOWN GPIO */
- OMAP3_MUX(GPMC_NCS6, OMAP_MUX_MODE4 | OMAP_PIN_INPUT),
-
- /* mUSB */
- OMAP3_MUX(HSUSB0_CLK, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
- OMAP3_MUX(HSUSB0_STP, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(HSUSB0_DIR, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
- OMAP3_MUX(HSUSB0_NXT, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
- OMAP3_MUX(HSUSB0_DATA0, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
- OMAP3_MUX(HSUSB0_DATA1, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
- OMAP3_MUX(HSUSB0_DATA2, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
- OMAP3_MUX(HSUSB0_DATA3, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
- OMAP3_MUX(HSUSB0_DATA4, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
- OMAP3_MUX(HSUSB0_DATA5, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
- OMAP3_MUX(HSUSB0_DATA6, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
- OMAP3_MUX(HSUSB0_DATA7, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
-
- /* MMC 2 */
- OMAP3_MUX(SDMMC2_DAT4, OMAP_MUX_MODE1 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(SDMMC2_DAT5, OMAP_MUX_MODE1 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(SDMMC2_DAT6, OMAP_MUX_MODE1 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(SDMMC2_DAT7, OMAP_MUX_MODE1 | OMAP_PIN_INPUT),
-
- /* McSPI 1 */
- OMAP3_MUX(MCSPI1_CLK, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
- OMAP3_MUX(MCSPI1_SIMO, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
- OMAP3_MUX(MCSPI1_SOMI, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
- OMAP3_MUX(MCSPI1_CS0, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLDOWN),
-
- /* McSPI 4 */
- OMAP3_MUX(MCBSP1_CLKR, OMAP_MUX_MODE1 | OMAP_PIN_INPUT),
- OMAP3_MUX(MCBSP1_DX, OMAP_MUX_MODE1 | OMAP_PIN_INPUT),
- OMAP3_MUX(MCBSP1_DR, OMAP_MUX_MODE1 | OMAP_PIN_INPUT),
- OMAP3_MUX(MCBSP1_FSX, OMAP_MUX_MODE1 | OMAP_PIN_INPUT_PULLUP),
-
- /* McBSP 2 */
- OMAP3_MUX(MCBSP2_FSX, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
- OMAP3_MUX(MCBSP2_CLKX, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
- OMAP3_MUX(MCBSP2_DR, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
- OMAP3_MUX(MCBSP2_DX, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
-
- /* serial ports */
- OMAP3_MUX(MCBSP3_CLKX, OMAP_MUX_MODE1 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(MCBSP3_FSX, OMAP_MUX_MODE1 | OMAP_PIN_INPUT),
- OMAP3_MUX(UART1_TX, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(UART1_RX, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
-
- /* common DSS */
- OMAP3_MUX(DSS_PCLK, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(DSS_HSYNC, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(DSS_VSYNC, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(DSS_ACBIAS, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(DSS_DATA6, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(DSS_DATA7, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(DSS_DATA8, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(DSS_DATA9, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(DSS_DATA10, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(DSS_DATA11, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(DSS_DATA12, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(DSS_DATA13, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(DSS_DATA14, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(DSS_DATA15, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(DSS_DATA16, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(DSS_DATA17, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
-
- /* Camera */
- OMAP3_MUX(CAM_HS, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
- OMAP3_MUX(CAM_VS, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
- OMAP3_MUX(CAM_XCLKA, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
- OMAP3_MUX(CAM_PCLK, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
- OMAP3_MUX(CAM_FLD, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
- OMAP3_MUX(CAM_D0, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
- OMAP3_MUX(CAM_D1, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
- OMAP3_MUX(CAM_D2, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
- OMAP3_MUX(CAM_D3, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
- OMAP3_MUX(CAM_D4, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
- OMAP3_MUX(CAM_D5, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
- OMAP3_MUX(CAM_D6, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
- OMAP3_MUX(CAM_D7, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
- OMAP3_MUX(CAM_D8, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLDOWN),
- OMAP3_MUX(CAM_D9, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLDOWN),
- OMAP3_MUX(CAM_STROBE, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
-
- OMAP3_MUX(CAM_D10, OMAP_MUX_MODE4 | OMAP_PIN_INPUT_PULLDOWN),
- OMAP3_MUX(CAM_D11, OMAP_MUX_MODE4 | OMAP_PIN_INPUT_PULLDOWN),
-
- /* display controls */
- OMAP3_MUX(MCBSP1_FSR, OMAP_MUX_MODE4 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(GPMC_NCS7, OMAP_MUX_MODE4 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(GPMC_NCS3, OMAP_MUX_MODE4 | OMAP_PIN_OUTPUT),
-
- /* TPS IRQ */
- OMAP3_MUX(SYS_NIRQ, OMAP_MUX_MODE0 | OMAP_WAKEUP_EN | \
- OMAP_PIN_INPUT_PULLUP),
-
- { .reg_offset = OMAP_MUX_TERMINATOR },
-};
-
-static void __init cm_t3x_common_dss_mux_init(int mux_mode)
-{
- omap_mux_init_signal("dss_data18", mux_mode);
- omap_mux_init_signal("dss_data19", mux_mode);
- omap_mux_init_signal("dss_data20", mux_mode);
- omap_mux_init_signal("dss_data21", mux_mode);
- omap_mux_init_signal("dss_data22", mux_mode);
- omap_mux_init_signal("dss_data23", mux_mode);
-}
-
-static void __init cm_t35_init_mux(void)
-{
- int mux_mode = OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT;
-
- omap_mux_init_signal("dss_data0.dss_data0", mux_mode);
- omap_mux_init_signal("dss_data1.dss_data1", mux_mode);
- omap_mux_init_signal("dss_data2.dss_data2", mux_mode);
- omap_mux_init_signal("dss_data3.dss_data3", mux_mode);
- omap_mux_init_signal("dss_data4.dss_data4", mux_mode);
- omap_mux_init_signal("dss_data5.dss_data5", mux_mode);
- cm_t3x_common_dss_mux_init(mux_mode);
-}
-
-static void __init cm_t3730_init_mux(void)
-{
- int mux_mode = OMAP_MUX_MODE3 | OMAP_PIN_OUTPUT;
-
- omap_mux_init_signal("sys_boot0", mux_mode);
- omap_mux_init_signal("sys_boot1", mux_mode);
- omap_mux_init_signal("sys_boot3", mux_mode);
- omap_mux_init_signal("sys_boot4", mux_mode);
- omap_mux_init_signal("sys_boot5", mux_mode);
- omap_mux_init_signal("sys_boot6", mux_mode);
- cm_t3x_common_dss_mux_init(mux_mode);
-}
-#else
-static inline void cm_t35_init_mux(void) {}
-static inline void cm_t3730_init_mux(void) {}
-#endif
-
-static void __init cm_t3x_common_init(void)
-{
- omap3_mux_init(board_mux, OMAP_PACKAGE_CUS);
- omap_serial_init();
- omap_sdrc_init(mt46h32m32lf6_sdrc_params,
- mt46h32m32lf6_sdrc_params);
- omap_hsmmc_init(mmc);
- cm_t35_init_i2c();
- omap_ads7846_init(1, CM_T35_GPIO_PENDOWN, 0, NULL);
- cm_t35_init_ethernet();
- cm_t35_init_led();
- cm_t35_init_display();
- omap_twl4030_audio_init("cm-t3x", NULL);
-
- usb_bind_phy("musb-hdrc.0.auto", 0, "twl4030_usb");
- usb_musb_init(NULL);
- cm_t35_init_usbh();
- cm_t35_init_camera();
-}
-
-static void __init cm_t35_init(void)
-{
- cm_t3x_common_init();
- cm_t35_init_mux();
- cm_t35_init_nand();
-}
-
-static void __init cm_t3730_init(void)
-{
- cm_t3x_common_init();
- cm_t3730_init_mux();
-}
-
-MACHINE_START(CM_T35, "Compulab CM-T35")
- .atag_offset = 0x100,
- .reserve = omap_reserve,
- .map_io = omap3_map_io,
- .init_early = omap35xx_init_early,
- .init_irq = omap3_init_irq,
- .init_machine = cm_t35_init,
- .init_late = omap35xx_init_late,
- .init_time = omap3_sync32k_timer_init,
- .restart = omap3xxx_restart,
-MACHINE_END
-
-MACHINE_START(CM_T3730, "Compulab CM-T3730")
- .atag_offset = 0x100,
- .reserve = omap_reserve,
- .map_io = omap3_map_io,
- .init_early = omap3630_init_early,
- .init_irq = omap3_init_irq,
- .init_machine = cm_t3730_init,
- .init_late = omap3630_init_late,
- .init_time = omap3_sync32k_timer_init,
- .restart = omap3xxx_restart,
-MACHINE_END
diff --git a/arch/arm/mach-omap2/board-omap3beagle.c b/arch/arm/mach-omap2/board-omap3beagle.c
deleted file mode 100644
index 81de1c6..0000000
--- a/arch/arm/mach-omap2/board-omap3beagle.c
+++ /dev/null
@@ -1,595 +0,0 @@
-/*
- * linux/arch/arm/mach-omap2/board-omap3beagle.c
- *
- * Copyright (C) 2008 Texas Instruments
- *
- * Modified from mach-omap2/board-3430sdp.c
- *
- * Initial code: Syed Mohammed Khasim
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/platform_device.h>
-#include <linux/delay.h>
-#include <linux/err.h>
-#include <linux/clk.h>
-#include <linux/io.h>
-#include <linux/leds.h>
-#include <linux/pwm.h>
-#include <linux/leds_pwm.h>
-#include <linux/gpio.h>
-#include <linux/input.h>
-#include <linux/gpio_keys.h>
-#include <linux/pm_opp.h>
-#include <linux/cpu.h>
-
-#include <linux/mtd/mtd.h>
-#include <linux/mtd/partitions.h>
-#include <linux/mtd/nand.h>
-#include <linux/mmc/host.h>
-#include <linux/usb/phy.h>
-
-#include <linux/regulator/machine.h>
-#include <linux/i2c/twl.h>
-
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-#include <asm/mach/map.h>
-#include <asm/mach/flash.h>
-
-#include <video/omapdss.h>
-#include <video/omap-panel-data.h>
-#include <linux/platform_data/mtd-nand-omap2.h>
-
-#include "common.h"
-#include "omap_device.h"
-#include "gpmc.h"
-#include "soc.h"
-#include "mux.h"
-#include "hsmmc.h"
-#include "pm.h"
-#include "board-flash.h"
-#include "common-board-devices.h"
-
-#define NAND_CS 0
-
-static struct pwm_lookup pwm_lookup[] = {
- /* LEDB -> PMU_STAT */
- PWM_LOOKUP("twl-pwmled", 1, "leds_pwm", "beagleboard::pmu_stat",
- 7812500, PWM_POLARITY_NORMAL),
-};
-
-static struct led_pwm pwm_leds[] = {
- {
- .name = "beagleboard::pmu_stat",
- .max_brightness = 127,
- .pwm_period_ns = 7812500,
- },
-};
-
-static struct led_pwm_platform_data pwm_data = {
- .num_leds = ARRAY_SIZE(pwm_leds),
- .leds = pwm_leds,
-};
-
-static struct platform_device leds_pwm = {
- .name = "leds_pwm",
- .id = -1,
- .dev = {
- .platform_data = &pwm_data,
- },
-};
-
-/*
- * OMAP3 Beagle revision
- * Run time detection of Beagle revision is done by reading GPIO.
- * GPIO ID -
- * AXBX = GPIO173, GPIO172, GPIO171: 1 1 1
- * C1_3 = GPIO173, GPIO172, GPIO171: 1 1 0
- * C4 = GPIO173, GPIO172, GPIO171: 1 0 1
- * XMA/XMB = GPIO173, GPIO172, GPIO171: 0 0 0
- * XMC = GPIO173, GPIO172, GPIO171: 0 1 0
- */
-enum {
- OMAP3BEAGLE_BOARD_UNKN = 0,
- OMAP3BEAGLE_BOARD_AXBX,
- OMAP3BEAGLE_BOARD_C1_3,
- OMAP3BEAGLE_BOARD_C4,
- OMAP3BEAGLE_BOARD_XM,
- OMAP3BEAGLE_BOARD_XMC,
-};
-
-static u8 omap3_beagle_version;
-
-/*
- * Board-specific configuration
- * Defaults to BeagleBoard-xMC
- */
-static struct {
- int mmc1_gpio_wp;
- bool usb_pwr_level; /* 0 - Active Low, 1 - Active High */
- int dvi_pd_gpio;
- int usr_button_gpio;
- int mmc_caps;
-} beagle_config = {
- .mmc1_gpio_wp = -EINVAL,
- .usb_pwr_level = 0,
- .dvi_pd_gpio = -EINVAL,
- .usr_button_gpio = 4,
- .mmc_caps = MMC_CAP_4_BIT_DATA | MMC_CAP_8_BIT_DATA,
-};
-
-static struct gpio omap3_beagle_rev_gpios[] __initdata = {
- { 171, GPIOF_IN, "rev_id_0" },
- { 172, GPIOF_IN, "rev_id_1" },
- { 173, GPIOF_IN, "rev_id_2" },
-};
-
-static void __init omap3_beagle_init_rev(void)
-{
- int ret;
- u16 beagle_rev = 0;
-
- omap_mux_init_gpio(171, OMAP_PIN_INPUT_PULLUP);
- omap_mux_init_gpio(172, OMAP_PIN_INPUT_PULLUP);
- omap_mux_init_gpio(173, OMAP_PIN_INPUT_PULLUP);
-
- ret = gpio_request_array(omap3_beagle_rev_gpios,
- ARRAY_SIZE(omap3_beagle_rev_gpios));
- if (ret < 0) {
- printk(KERN_ERR "Unable to get revision detection GPIO pins\n");
- omap3_beagle_version = OMAP3BEAGLE_BOARD_UNKN;
- return;
- }
-
- beagle_rev = gpio_get_value(171) | (gpio_get_value(172) << 1)
- | (gpio_get_value(173) << 2);
-
- gpio_free_array(omap3_beagle_rev_gpios,
- ARRAY_SIZE(omap3_beagle_rev_gpios));
-
- switch (beagle_rev) {
- case 7:
- printk(KERN_INFO "OMAP3 Beagle Rev: Ax/Bx\n");
- omap3_beagle_version = OMAP3BEAGLE_BOARD_AXBX;
- beagle_config.mmc1_gpio_wp = 29;
- beagle_config.dvi_pd_gpio = 170;
- beagle_config.usr_button_gpio = 7;
- break;
- case 6:
- printk(KERN_INFO "OMAP3 Beagle Rev: C1/C2/C3\n");
- omap3_beagle_version = OMAP3BEAGLE_BOARD_C1_3;
- beagle_config.mmc1_gpio_wp = 23;
- beagle_config.dvi_pd_gpio = 170;
- beagle_config.usr_button_gpio = 7;
- break;
- case 5:
- printk(KERN_INFO "OMAP3 Beagle Rev: C4\n");
- omap3_beagle_version = OMAP3BEAGLE_BOARD_C4;
- beagle_config.mmc1_gpio_wp = 23;
- beagle_config.dvi_pd_gpio = 170;
- beagle_config.usr_button_gpio = 7;
- break;
- case 0:
- printk(KERN_INFO "OMAP3 Beagle Rev: xM Ax/Bx\n");
- omap3_beagle_version = OMAP3BEAGLE_BOARD_XM;
- beagle_config.usb_pwr_level = 1;
- beagle_config.mmc_caps &= ~MMC_CAP_8_BIT_DATA;
- break;
- case 2:
- printk(KERN_INFO "OMAP3 Beagle Rev: xM C\n");
- omap3_beagle_version = OMAP3BEAGLE_BOARD_XMC;
- beagle_config.mmc_caps &= ~MMC_CAP_8_BIT_DATA;
- break;
- default:
- printk(KERN_INFO "OMAP3 Beagle Rev: unknown %hd\n", beagle_rev);
- omap3_beagle_version = OMAP3BEAGLE_BOARD_UNKN;
- }
-}
-
-static struct mtd_partition omap3beagle_nand_partitions[] = {
- /* All the partition sizes are listed in terms of NAND block size */
- {
- .name = "X-Loader",
- .offset = 0,
- .size = 4 * NAND_BLOCK_SIZE,
- .mask_flags = MTD_WRITEABLE, /* force read-only */
- },
- {
- .name = "U-Boot",
- .offset = MTDPART_OFS_APPEND, /* Offset = 0x80000 */
- .size = 15 * NAND_BLOCK_SIZE,
- .mask_flags = MTD_WRITEABLE, /* force read-only */
- },
- {
- .name = "U-Boot Env",
- .offset = MTDPART_OFS_APPEND, /* Offset = 0x260000 */
- .size = 1 * NAND_BLOCK_SIZE,
- },
- {
- .name = "Kernel",
- .offset = MTDPART_OFS_APPEND, /* Offset = 0x280000 */
- .size = 32 * NAND_BLOCK_SIZE,
- },
- {
- .name = "File System",
- .offset = MTDPART_OFS_APPEND, /* Offset = 0x680000 */
- .size = MTDPART_SIZ_FULL,
- },
-};
-
-/* DSS */
-
-static struct connector_dvi_platform_data beagle_dvi_connector_pdata = {
- .name = "dvi",
- .source = "tfp410.0",
- .i2c_bus_num = 3,
-};
-
-static struct platform_device beagle_dvi_connector_device = {
- .name = "connector-dvi",
- .id = 0,
- .dev.platform_data = &beagle_dvi_connector_pdata,
-};
-
-static struct encoder_tfp410_platform_data beagle_tfp410_pdata = {
- .name = "tfp410.0",
- .source = "dpi.0",
- .data_lines = 24,
- .power_down_gpio = -1,
-};
-
-static struct platform_device beagle_tfp410_device = {
- .name = "tfp410",
- .id = 0,
- .dev.platform_data = &beagle_tfp410_pdata,
-};
-
-static struct connector_atv_platform_data beagle_tv_pdata = {
- .name = "tv",
- .source = "venc.0",
- .connector_type = OMAP_DSS_VENC_TYPE_SVIDEO,
- .invert_polarity = false,
-};
-
-static struct platform_device beagle_tv_connector_device = {
- .name = "connector-analog-tv",
- .id = 0,
- .dev.platform_data = &beagle_tv_pdata,
-};
-
-static struct omap_dss_board_info beagle_dss_data = {
- .default_display_name = "dvi",
-};
-
-#include "sdram-micron-mt46h32m32lf-6.h"
-
-static struct omap2_hsmmc_info mmc[] = {
- {
- .mmc = 1,
- .caps = MMC_CAP_4_BIT_DATA,
- .gpio_wp = -EINVAL,
- .deferred = true,
- },
- {} /* Terminator */
-};
-
-static struct regulator_consumer_supply beagle_vmmc1_supply[] = {
- REGULATOR_SUPPLY("vmmc", "omap_hsmmc.0"),
-};
-
-static struct regulator_consumer_supply beagle_vsim_supply[] = {
- REGULATOR_SUPPLY("vmmc_aux", "omap_hsmmc.0"),
-};
-
-static struct gpio_led gpio_leds[];
-
-static struct usbhs_phy_data phy_data[] = {
- {
- .port = 2,
- .reset_gpio = 147,
- .vcc_gpio = -1, /* updated in beagle_twl_gpio_setup */
- .vcc_polarity = 1, /* updated in beagle_twl_gpio_setup */
- },
-};
-
-static int beagle_twl_gpio_setup(struct device *dev,
- unsigned gpio, unsigned ngpio)
-{
- int r;
-
- mmc[0].gpio_wp = beagle_config.mmc1_gpio_wp;
- /* gpio + 0 is "mmc0_cd" (input/IRQ) */
- mmc[0].gpio_cd = gpio + 0;
- omap_hsmmc_late_init(mmc);
-
- /*
- * TWL4030_GPIO_MAX + 0 == ledA, EHCI nEN_USB_PWR (out, XM active
- * high / others active low)
- * DVI reset GPIO is different between beagle revisions
- */
- /* Valid for all -xM revisions */
- if (cpu_is_omap3630()) {
- /*
- * gpio + 1 on Xm controls the TFP410's enable line (active low)
- * gpio + 2 control varies depending on the board rev as below:
- * P7/P8 revisions(prototype): Camera EN
- * A2+ revisions (production): LDO (DVI, serial, led blocks)
- */
- r = gpio_request_one(gpio + 1, GPIOF_OUT_INIT_LOW,
- "nDVI_PWR_EN");
- if (r)
- pr_err("%s: unable to configure nDVI_PWR_EN\n",
- __func__);
-
- beagle_config.dvi_pd_gpio = gpio + 2;
-
- } else {
- /*
- * REVISIT: need ehci-omap hooks for external VBUS
- * power switch and overcurrent detect
- */
- if (gpio_request_one(gpio + 1, GPIOF_IN, "EHCI_nOC"))
- pr_err("%s: unable to configure EHCI_nOC\n", __func__);
- }
- beagle_tfp410_pdata.power_down_gpio = beagle_config.dvi_pd_gpio;
-
- platform_device_register(&beagle_tfp410_device);
- platform_device_register(&beagle_dvi_connector_device);
- platform_device_register(&beagle_tv_connector_device);
-
- /* TWL4030_GPIO_MAX i.e. LED_GPO controls HS USB Port 2 power */
- phy_data[0].vcc_gpio = gpio + TWL4030_GPIO_MAX;
- phy_data[0].vcc_polarity = beagle_config.usb_pwr_level;
-
- usbhs_init_phys(phy_data, ARRAY_SIZE(phy_data));
- return 0;
-}
-
-static struct twl4030_gpio_platform_data beagle_gpio_data = {
- .use_leds = true,
- .pullups = BIT(1),
- .pulldowns = BIT(2) | BIT(6) | BIT(7) | BIT(8) | BIT(13)
- | BIT(15) | BIT(16) | BIT(17),
- .setup = beagle_twl_gpio_setup,
-};
-
-/* VMMC1 for MMC1 pins CMD, CLK, DAT0..DAT3 (20 mA, plus card == max 220 mA) */
-static struct regulator_init_data beagle_vmmc1 = {
- .constraints = {
- .min_uV = 1850000,
- .max_uV = 3150000,
- .valid_modes_mask = REGULATOR_MODE_NORMAL
- | REGULATOR_MODE_STANDBY,
- .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE
- | REGULATOR_CHANGE_MODE
- | REGULATOR_CHANGE_STATUS,
- },
- .num_consumer_supplies = ARRAY_SIZE(beagle_vmmc1_supply),
- .consumer_supplies = beagle_vmmc1_supply,
-};
-
-/* VSIM for MMC1 pins DAT4..DAT7 (2 mA, plus card == max 50 mA) */
-static struct regulator_init_data beagle_vsim = {
- .constraints = {
- .min_uV = 1800000,
- .max_uV = 3000000,
- .valid_modes_mask = REGULATOR_MODE_NORMAL
- | REGULATOR_MODE_STANDBY,
- .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE
- | REGULATOR_CHANGE_MODE
- | REGULATOR_CHANGE_STATUS,
- },
- .num_consumer_supplies = ARRAY_SIZE(beagle_vsim_supply),
- .consumer_supplies = beagle_vsim_supply,
-};
-
-static struct twl4030_platform_data beagle_twldata = {
- /* platform_data for children goes here */
- .gpio = &beagle_gpio_data,
- .vmmc1 = &beagle_vmmc1,
- .vsim = &beagle_vsim,
-};
-
-static struct i2c_board_info __initdata beagle_i2c_eeprom[] = {
- {
- I2C_BOARD_INFO("eeprom", 0x50),
- },
-};
-
-static int __init omap3_beagle_i2c_init(void)
-{
- omap3_pmic_get_config(&beagle_twldata,
- TWL_COMMON_PDATA_USB | TWL_COMMON_PDATA_MADC |
- TWL_COMMON_PDATA_AUDIO,
- TWL_COMMON_REGULATOR_VDAC | TWL_COMMON_REGULATOR_VPLL2);
-
- beagle_twldata.vpll2->constraints.name = "VDVI";
-
- omap3_pmic_init("twl4030", &beagle_twldata);
- /* Bus 3 is attached to the DVI port where devices like the pico DLP
- * projector don't work reliably with 400kHz */
- omap_register_i2c_bus(3, 100, beagle_i2c_eeprom, ARRAY_SIZE(beagle_i2c_eeprom));
- return 0;
-}
-
-static struct gpio_led gpio_leds[] = {
- {
- .name = "beagleboard::usr0",
- .default_trigger = "heartbeat",
- .gpio = 150,
- },
- {
- .name = "beagleboard::usr1",
- .default_trigger = "mmc0",
- .gpio = 149,
- },
-};
-
-static struct gpio_led_platform_data gpio_led_info = {
- .leds = gpio_leds,
- .num_leds = ARRAY_SIZE(gpio_leds),
-};
-
-static struct platform_device leds_gpio = {
- .name = "leds-gpio",
- .id = -1,
- .dev = {
- .platform_data = &gpio_led_info,
- },
-};
-
-static struct gpio_keys_button gpio_buttons[] = {
- {
- .code = BTN_EXTRA,
- /* Dynamically assigned depending on board */
- .gpio = -EINVAL,
- .desc = "user",
- .wakeup = 1,
- },
-};
-
-static struct gpio_keys_platform_data gpio_key_info = {
- .buttons = gpio_buttons,
- .nbuttons = ARRAY_SIZE(gpio_buttons),
-};
-
-static struct platform_device keys_gpio = {
- .name = "gpio-keys",
- .id = -1,
- .dev = {
- .platform_data = &gpio_key_info,
- },
-};
-
-static struct platform_device madc_hwmon = {
- .name = "twl4030_madc_hwmon",
- .id = -1,
-};
-
-static struct platform_device *omap3_beagle_devices[] __initdata = {
- &leds_gpio,
- &keys_gpio,
- &madc_hwmon,
- &leds_pwm,
-};
-
-static struct usbhs_omap_platform_data usbhs_bdata __initdata = {
- .port_mode[1] = OMAP_EHCI_PORT_MODE_PHY,
-};
-
-#ifdef CONFIG_OMAP_MUX
-static struct omap_board_mux board_mux[] __initdata = {
- { .reg_offset = OMAP_MUX_TERMINATOR },
-};
-#endif
-
-static int __init beagle_opp_init(void)
-{
- int r = 0;
-
- if (!machine_is_omap3_beagle())
- return 0;
-
- /* Initialize the omap3 opp table if not already created. */
- r = omap3_opp_init();
- if (r < 0 && (r != -EEXIST)) {
- pr_err("%s: opp default init failed\n", __func__);
- return r;
- }
-
- /* Custom OPP enabled for all xM versions */
- if (cpu_is_omap3630()) {
- struct device *mpu_dev, *iva_dev;
-
- mpu_dev = get_cpu_device(0);
- iva_dev = omap_device_get_by_hwmod_name("iva");
-
- if (!mpu_dev || IS_ERR(iva_dev)) {
- pr_err("%s: Aiee.. no mpu/dsp devices? %p %p\n",
- __func__, mpu_dev, iva_dev);
- return -ENODEV;
- }
- /* Enable MPU 1GHz and lower opps */
- r = dev_pm_opp_enable(mpu_dev, 800000000);
- /* TODO: MPU 1GHz needs SR and ABB */
-
- /* Enable IVA 800MHz and lower opps */
- r |= dev_pm_opp_enable(iva_dev, 660000000);
- /* TODO: DSP 800MHz needs SR and ABB */
- if (r) {
- pr_err("%s: failed to enable higher opp %d\n",
- __func__, r);
- /*
- * Cleanup - disable the higher freqs - we dont care
- * about the results
- */
- dev_pm_opp_disable(mpu_dev, 800000000);
- dev_pm_opp_disable(iva_dev, 660000000);
- }
- }
- return 0;
-}
-omap_device_initcall(beagle_opp_init);
-
-static void __init omap3_beagle_init(void)
-{
- omap3_mux_init(board_mux, OMAP_PACKAGE_CBB);
- omap3_beagle_init_rev();
-
- if (gpio_is_valid(beagle_config.mmc1_gpio_wp))
- omap_mux_init_gpio(beagle_config.mmc1_gpio_wp, OMAP_PIN_INPUT);
- mmc[0].caps = beagle_config.mmc_caps;
- omap_hsmmc_init(mmc);
-
- omap3_beagle_i2c_init();
-
- gpio_buttons[0].gpio = beagle_config.usr_button_gpio;
-
- platform_add_devices(omap3_beagle_devices,
- ARRAY_SIZE(omap3_beagle_devices));
- if (gpio_is_valid(beagle_config.dvi_pd_gpio))
- omap_mux_init_gpio(beagle_config.dvi_pd_gpio, OMAP_PIN_OUTPUT);
- omap_display_init(&beagle_dss_data);
-
- omap_serial_init();
- omap_sdrc_init(mt46h32m32lf6_sdrc_params,
- mt46h32m32lf6_sdrc_params);
-
- usb_bind_phy("musb-hdrc.0.auto", 0, "twl4030_usb");
- usb_musb_init(NULL);
-
- usbhs_init(&usbhs_bdata);
-
- board_nand_init(omap3beagle_nand_partitions,
- ARRAY_SIZE(omap3beagle_nand_partitions), NAND_CS,
- NAND_BUSWIDTH_16, NULL);
- omap_twl4030_audio_init("omap3beagle", NULL);
-
- /* Ensure msecure is mux'd to be able to set the RTC. */
- omap_mux_init_signal("sys_drm_msecure", OMAP_PIN_OFF_OUTPUT_HIGH);
-
- /* Ensure SDRC pins are mux'd for self-refresh */
- omap_mux_init_signal("sdrc_cke0", OMAP_PIN_OUTPUT);
- omap_mux_init_signal("sdrc_cke1", OMAP_PIN_OUTPUT);
-
- pwm_add_table(pwm_lookup, ARRAY_SIZE(pwm_lookup));
-}
-
-MACHINE_START(OMAP3_BEAGLE, "OMAP3 Beagle Board")
- /* Maintainer: Syed Mohammed Khasim - http://beagleboard.org */
- .atag_offset = 0x100,
- .reserve = omap_reserve,
- .map_io = omap3_map_io,
- .init_early = omap3_init_early,
- .init_irq = omap3_init_irq,
- .init_machine = omap3_beagle_init,
- .init_late = omap3_init_late,
- .init_time = omap3_secure_sync32k_timer_init,
- .restart = omap3xxx_restart,
-MACHINE_END
diff --git a/arch/arm/mach-omap2/board-overo.c b/arch/arm/mach-omap2/board-overo.c
deleted file mode 100644
index 2dae6cc..0000000
--- a/arch/arm/mach-omap2/board-overo.c
+++ /dev/null
@@ -1,571 +0,0 @@
-/*
- * board-overo.c (Gumstix Overo)
- *
- * Initial code: Steve Sakoman <steve@sakoman.com>
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License
- * version 2 as published by the Free Software Foundation.
- *
- * This program is distributed in the hope that it will be useful, but
- * WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
- * General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA
- * 02110-1301 USA
- *
- */
-
-#include <linux/clk.h>
-#include <linux/delay.h>
-#include <linux/err.h>
-#include <linux/init.h>
-#include <linux/io.h>
-#include <linux/gpio.h>
-#include <linux/kernel.h>
-#include <linux/platform_device.h>
-#include <linux/i2c/twl.h>
-#include <linux/regulator/machine.h>
-#include <linux/regulator/fixed.h>
-#include <linux/spi/spi.h>
-
-#include <linux/mtd/mtd.h>
-#include <linux/mtd/nand.h>
-#include <linux/mtd/partitions.h>
-#include <linux/mmc/host.h>
-#include <linux/usb/phy.h>
-
-#include <linux/platform_data/mtd-nand-omap2.h>
-#include <linux/platform_data/spi-omap2-mcspi.h>
-
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-#include <asm/mach/flash.h>
-#include <asm/mach/map.h>
-
-#include <video/omapdss.h>
-#include <video/omap-panel-data.h>
-
-#include "common.h"
-#include "mux.h"
-#include "sdram-micron-mt46h32m32lf-6.h"
-#include "gpmc.h"
-#include "hsmmc.h"
-#include "board-flash.h"
-#include "common-board-devices.h"
-
-#define NAND_CS 0
-
-#define OVERO_GPIO_BT_XGATE 15
-#define OVERO_GPIO_W2W_NRESET 16
-#define OVERO_GPIO_PENDOWN 114
-#define OVERO_GPIO_BT_NRESET 164
-#define OVERO_GPIO_USBH_CPEN 168
-#define OVERO_GPIO_USBH_NRESET 183
-
-#define OVERO_SMSC911X_CS 5
-#define OVERO_SMSC911X_GPIO 176
-#define OVERO_SMSC911X_NRESET 64
-#define OVERO_SMSC911X2_CS 4
-#define OVERO_SMSC911X2_GPIO 65
-
-/* whether to register LCD35 instead of LCD43 */
-static bool overo_use_lcd35;
-
-#if defined(CONFIG_TOUCHSCREEN_ADS7846) || \
- defined(CONFIG_TOUCHSCREEN_ADS7846_MODULE)
-
-/* fixed regulator for ads7846 */
-static struct regulator_consumer_supply ads7846_supply[] = {
- REGULATOR_SUPPLY("vcc", "spi1.0"),
-};
-
-static struct regulator_init_data vads7846_regulator = {
- .constraints = {
- .valid_ops_mask = REGULATOR_CHANGE_STATUS,
- },
- .num_consumer_supplies = ARRAY_SIZE(ads7846_supply),
- .consumer_supplies = ads7846_supply,
-};
-
-static struct fixed_voltage_config vads7846 = {
- .supply_name = "vads7846",
- .microvolts = 3300000, /* 3.3V */
- .gpio = -EINVAL,
- .startup_delay = 0,
- .init_data = &vads7846_regulator,
-};
-
-static struct platform_device vads7846_device = {
- .name = "reg-fixed-voltage",
- .id = 1,
- .dev = {
- .platform_data = &vads7846,
- },
-};
-
-static void __init overo_ads7846_init(void)
-{
- omap_ads7846_init(1, OVERO_GPIO_PENDOWN, 0, NULL);
- platform_device_register(&vads7846_device);
-}
-
-#else
-static inline void __init overo_ads7846_init(void) { return; }
-#endif
-
-#if defined(CONFIG_SMSC911X) || defined(CONFIG_SMSC911X_MODULE)
-
-#include <linux/smsc911x.h>
-#include "gpmc-smsc911x.h"
-
-static struct omap_smsc911x_platform_data smsc911x_cfg = {
- .id = 0,
- .cs = OVERO_SMSC911X_CS,
- .gpio_irq = OVERO_SMSC911X_GPIO,
- .gpio_reset = OVERO_SMSC911X_NRESET,
- .flags = SMSC911X_USE_32BIT,
-};
-
-static struct omap_smsc911x_platform_data smsc911x2_cfg = {
- .id = 1,
- .cs = OVERO_SMSC911X2_CS,
- .gpio_irq = OVERO_SMSC911X2_GPIO,
- .gpio_reset = -EINVAL,
- .flags = SMSC911X_USE_32BIT,
-};
-
-static void __init overo_init_smsc911x(void)
-{
- gpmc_smsc911x_init(&smsc911x_cfg);
- gpmc_smsc911x_init(&smsc911x2_cfg);
-}
-
-#else
-static inline void __init overo_init_smsc911x(void) { return; }
-#endif
-
-/* DSS */
-#define OVERO_GPIO_LCD_EN 144
-#define OVERO_GPIO_LCD_BL 145
-
-static struct connector_atv_platform_data overo_tv_pdata = {
- .name = "tv",
- .source = "venc.0",
- .connector_type = OMAP_DSS_VENC_TYPE_SVIDEO,
- .invert_polarity = false,
-};
-
-static struct platform_device overo_tv_connector_device = {
- .name = "connector-analog-tv",
- .id = 0,
- .dev.platform_data = &overo_tv_pdata,
-};
-
-static const struct display_timing overo_lcd43_videomode = {
- .pixelclock = { 0, 9200000, 0 },
-
- .hactive = { 0, 480, 0 },
- .hfront_porch = { 0, 8, 0 },
- .hback_porch = { 0, 4, 0 },
- .hsync_len = { 0, 41, 0 },
-
- .vactive = { 0, 272, 0 },
- .vfront_porch = { 0, 4, 0 },
- .vback_porch = { 0, 2, 0 },
- .vsync_len = { 0, 10, 0 },
-
- .flags = DISPLAY_FLAGS_HSYNC_LOW | DISPLAY_FLAGS_VSYNC_LOW |
- DISPLAY_FLAGS_DE_HIGH | DISPLAY_FLAGS_PIXDATA_POSEDGE,
-};
-
-static struct panel_dpi_platform_data overo_lcd43_pdata = {
- .name = "lcd43",
- .source = "dpi.0",
-
- .data_lines = 24,
-
- .display_timing = &overo_lcd43_videomode,
-
- .enable_gpio = OVERO_GPIO_LCD_EN,
- .backlight_gpio = OVERO_GPIO_LCD_BL,
-};
-
-static struct platform_device overo_lcd43_device = {
- .name = "panel-dpi",
- .id = 0,
- .dev.platform_data = &overo_lcd43_pdata,
-};
-
-static struct connector_dvi_platform_data overo_dvi_connector_pdata = {
- .name = "dvi",
- .source = "tfp410.0",
- .i2c_bus_num = 3,
-};
-
-static struct platform_device overo_dvi_connector_device = {
- .name = "connector-dvi",
- .id = 0,
- .dev.platform_data = &overo_dvi_connector_pdata,
-};
-
-static struct encoder_tfp410_platform_data overo_tfp410_pdata = {
- .name = "tfp410.0",
- .source = "dpi.0",
- .data_lines = 24,
- .power_down_gpio = -1,
-};
-
-static struct platform_device overo_tfp410_device = {
- .name = "tfp410",
- .id = 0,
- .dev.platform_data = &overo_tfp410_pdata,
-};
-
-static struct omap_dss_board_info overo_dss_data = {
- .default_display_name = "lcd43",
-};
-
-static void __init overo_display_init(void)
-{
- omap_display_init(&overo_dss_data);
-
- if (!overo_use_lcd35)
- platform_device_register(&overo_lcd43_device);
- platform_device_register(&overo_tfp410_device);
- platform_device_register(&overo_dvi_connector_device);
- platform_device_register(&overo_tv_connector_device);
-}
-
-static struct mtd_partition overo_nand_partitions[] = {
- {
- .name = "xloader",
- .offset = 0, /* Offset = 0x00000 */
- .size = 4 * NAND_BLOCK_SIZE,
- .mask_flags = MTD_WRITEABLE
- },
- {
- .name = "uboot",
- .offset = MTDPART_OFS_APPEND, /* Offset = 0x80000 */
- .size = 14 * NAND_BLOCK_SIZE,
- },
- {
- .name = "uboot environment",
- .offset = MTDPART_OFS_APPEND, /* Offset = 0x240000 */
- .size = 2 * NAND_BLOCK_SIZE,
- },
- {
- .name = "linux",
- .offset = MTDPART_OFS_APPEND, /* Offset = 0x280000 */
- .size = 32 * NAND_BLOCK_SIZE,
- },
- {
- .name = "rootfs",
- .offset = MTDPART_OFS_APPEND, /* Offset = 0x680000 */
- .size = MTDPART_SIZ_FULL,
- },
-};
-
-static struct omap2_hsmmc_info mmc[] = {
- {
- .mmc = 1,
- .caps = MMC_CAP_4_BIT_DATA,
- .gpio_cd = -EINVAL,
- .gpio_wp = -EINVAL,
- },
- {
- .mmc = 2,
- .caps = MMC_CAP_4_BIT_DATA,
- .gpio_cd = -EINVAL,
- .gpio_wp = -EINVAL,
- .transceiver = true,
- .ocr_mask = 0x00100000, /* 3.3V */
- },
- {} /* Terminator */
-};
-
-static struct regulator_consumer_supply overo_vmmc1_supply[] = {
- REGULATOR_SUPPLY("vmmc", "omap_hsmmc.0"),
-};
-
-#if defined(CONFIG_LEDS_GPIO) || defined(CONFIG_LEDS_GPIO_MODULE)
-#include <linux/leds.h>
-
-static struct gpio_led gpio_leds[] = {
- {
- .name = "overo:red:gpio21",
- .default_trigger = "heartbeat",
- .gpio = 21,
- .active_low = true,
- },
- {
- .name = "overo:blue:gpio22",
- .default_trigger = "none",
- .gpio = 22,
- .active_low = true,
- },
- {
- .name = "overo:blue:COM",
- .default_trigger = "mmc0",
- .gpio = -EINVAL, /* gets replaced */
- .active_low = true,
- },
-};
-
-static struct gpio_led_platform_data gpio_leds_pdata = {
- .leds = gpio_leds,
- .num_leds = ARRAY_SIZE(gpio_leds),
-};
-
-static struct platform_device gpio_leds_device = {
- .name = "leds-gpio",
- .id = -1,
- .dev = {
- .platform_data = &gpio_leds_pdata,
- },
-};
-
-static void __init overo_init_led(void)
-{
- platform_device_register(&gpio_leds_device);
-}
-
-#else
-static inline void __init overo_init_led(void) { return; }
-#endif
-
-#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
-#include <linux/input.h>
-#include <linux/gpio_keys.h>
-
-static struct gpio_keys_button gpio_buttons[] = {
- {
- .code = BTN_0,
- .gpio = 23,
- .desc = "button0",
- .wakeup = 1,
- },
- {
- .code = BTN_1,
- .gpio = 14,
- .desc = "button1",
- .wakeup = 1,
- },
-};
-
-static struct gpio_keys_platform_data gpio_keys_pdata = {
- .buttons = gpio_buttons,
- .nbuttons = ARRAY_SIZE(gpio_buttons),
-};
-
-static struct platform_device gpio_keys_device = {
- .name = "gpio-keys",
- .id = -1,
- .dev = {
- .platform_data = &gpio_keys_pdata,
- },
-};
-
-static void __init overo_init_keys(void)
-{
- platform_device_register(&gpio_keys_device);
-}
-
-#else
-static inline void __init overo_init_keys(void) { return; }
-#endif
-
-static int overo_twl_gpio_setup(struct device *dev,
- unsigned gpio, unsigned ngpio)
-{
-#if defined(CONFIG_LEDS_GPIO) || defined(CONFIG_LEDS_GPIO_MODULE)
- /* TWL4030_GPIO_MAX + 1 == ledB, PMU_STAT (out, active low LED) */
- gpio_leds[2].gpio = gpio + TWL4030_GPIO_MAX + 1;
-#endif
-
- return 0;
-}
-
-static struct twl4030_gpio_platform_data overo_gpio_data = {
- .use_leds = true,
- .setup = overo_twl_gpio_setup,
-};
-
-static struct regulator_init_data overo_vmmc1 = {
- .constraints = {
- .min_uV = 1850000,
- .max_uV = 3150000,
- .valid_modes_mask = REGULATOR_MODE_NORMAL
- | REGULATOR_MODE_STANDBY,
- .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE
- | REGULATOR_CHANGE_MODE
- | REGULATOR_CHANGE_STATUS,
- },
- .num_consumer_supplies = ARRAY_SIZE(overo_vmmc1_supply),
- .consumer_supplies = overo_vmmc1_supply,
-};
-
-static struct twl4030_platform_data overo_twldata = {
- .gpio = &overo_gpio_data,
- .vmmc1 = &overo_vmmc1,
-};
-
-static int __init overo_i2c_init(void)
-{
- omap3_pmic_get_config(&overo_twldata,
- TWL_COMMON_PDATA_USB | TWL_COMMON_PDATA_AUDIO,
- TWL_COMMON_REGULATOR_VDAC | TWL_COMMON_REGULATOR_VPLL2);
-
- overo_twldata.vpll2->constraints.name = "VDVI";
-
- omap3_pmic_init("tps65950", &overo_twldata);
- /* i2c2 pins are used for gpio */
- omap_register_i2c_bus(3, 400, NULL, 0);
- return 0;
-}
-
-static struct panel_lb035q02_platform_data overo_lcd35_pdata = {
- .name = "lcd35",
- .source = "dpi.0",
-
- .data_lines = 24,
-
- .enable_gpio = OVERO_GPIO_LCD_EN,
- .backlight_gpio = OVERO_GPIO_LCD_BL,
-};
-
-/*
- * NOTE: We need to add either the lgphilips panel, or the lcd43 panel. The
- * selection is done based on the overo_use_lcd35 field. If new SPI
- * devices are added here, extra work is needed to make only the lgphilips panel
- * affected by the overo_use_lcd35 field.
- */
-static struct spi_board_info overo_spi_board_info[] __initdata = {
- {
- .modalias = "panel_lgphilips_lb035q02",
- .bus_num = 1,
- .chip_select = 1,
- .max_speed_hz = 500000,
- .mode = SPI_MODE_3,
- .platform_data = &overo_lcd35_pdata,
- },
-};
-
-static int __init overo_spi_init(void)
-{
- overo_ads7846_init();
-
- if (overo_use_lcd35) {
- spi_register_board_info(overo_spi_board_info,
- ARRAY_SIZE(overo_spi_board_info));
- }
- return 0;
-}
-
-static struct usbhs_phy_data phy_data[] __initdata = {
- {
- .port = 2,
- .reset_gpio = OVERO_GPIO_USBH_NRESET,
- .vcc_gpio = -EINVAL,
- },
-};
-
-static struct usbhs_omap_platform_data usbhs_bdata __initdata = {
- .port_mode[1] = OMAP_EHCI_PORT_MODE_PHY,
-};
-
-#ifdef CONFIG_OMAP_MUX
-static struct omap_board_mux board_mux[] __initdata = {
- { .reg_offset = OMAP_MUX_TERMINATOR },
-};
-#endif
-
-static struct gpio overo_bt_gpios[] __initdata = {
- { OVERO_GPIO_BT_XGATE, GPIOF_OUT_INIT_LOW, "lcd enable" },
- { OVERO_GPIO_BT_NRESET, GPIOF_OUT_INIT_HIGH, "lcd bl enable" },
-};
-
-static struct regulator_consumer_supply dummy_supplies[] = {
- REGULATOR_SUPPLY("vddvario", "smsc911x.0"),
- REGULATOR_SUPPLY("vdd33a", "smsc911x.0"),
- REGULATOR_SUPPLY("vddvario", "smsc911x.1"),
- REGULATOR_SUPPLY("vdd33a", "smsc911x.1"),
-};
-
-static void __init overo_init(void)
-{
- int ret;
-
- if (strstr(boot_command_line, "omapdss.def_disp=lcd35"))
- overo_use_lcd35 = true;
-
- regulator_register_fixed(0, dummy_supplies, ARRAY_SIZE(dummy_supplies));
- omap3_mux_init(board_mux, OMAP_PACKAGE_CBB);
- overo_i2c_init();
- omap_hsmmc_init(mmc);
- omap_serial_init();
- omap_sdrc_init(mt46h32m32lf6_sdrc_params,
- mt46h32m32lf6_sdrc_params);
- board_nand_init(overo_nand_partitions,
- ARRAY_SIZE(overo_nand_partitions), NAND_CS, 0, NULL);
- usb_bind_phy("musb-hdrc.0.auto", 0, "twl4030_usb");
- usb_musb_init(NULL);
-
- usbhs_init_phys(phy_data, ARRAY_SIZE(phy_data));
- usbhs_init(&usbhs_bdata);
- overo_spi_init();
- overo_init_smsc911x();
- overo_init_led();
- overo_init_keys();
- omap_twl4030_audio_init("overo", NULL);
-
- overo_display_init();
-
- /* Ensure SDRC pins are mux'd for self-refresh */
- omap_mux_init_signal("sdrc_cke0", OMAP_PIN_OUTPUT);
- omap_mux_init_signal("sdrc_cke1", OMAP_PIN_OUTPUT);
-
- ret = gpio_request_one(OVERO_GPIO_W2W_NRESET, GPIOF_OUT_INIT_HIGH,
- "OVERO_GPIO_W2W_NRESET");
- if (ret == 0) {
- gpio_export(OVERO_GPIO_W2W_NRESET, 0);
- gpio_set_value(OVERO_GPIO_W2W_NRESET, 0);
- udelay(10);
- gpio_set_value(OVERO_GPIO_W2W_NRESET, 1);
- } else {
- pr_err("could not obtain gpio for OVERO_GPIO_W2W_NRESET\n");
- }
-
- ret = gpio_request_array(overo_bt_gpios, ARRAY_SIZE(overo_bt_gpios));
- if (ret) {
- pr_err("%s: could not obtain BT gpios\n", __func__);
- } else {
- gpio_export(OVERO_GPIO_BT_XGATE, 0);
- gpio_export(OVERO_GPIO_BT_NRESET, 0);
- gpio_set_value(OVERO_GPIO_BT_NRESET, 0);
- mdelay(6);
- gpio_set_value(OVERO_GPIO_BT_NRESET, 1);
- }
-
- ret = gpio_request_one(OVERO_GPIO_USBH_CPEN, GPIOF_OUT_INIT_HIGH,
- "OVERO_GPIO_USBH_CPEN");
- if (ret == 0)
- gpio_export(OVERO_GPIO_USBH_CPEN, 0);
- else
- pr_err("could not obtain gpio for OVERO_GPIO_USBH_CPEN\n");
-}
-
-MACHINE_START(OVERO, "Gumstix Overo")
- .atag_offset = 0x100,
- .reserve = omap_reserve,
- .map_io = omap3_map_io,
- .init_early = omap35xx_init_early,
- .init_irq = omap3_init_irq,
- .init_machine = overo_init,
- .init_late = omap35xx_init_late,
- .init_time = omap3_sync32k_timer_init,
- .restart = omap3xxx_restart,
-MACHINE_END
diff --git a/arch/arm/mach-omap2/devices.c b/arch/arm/mach-omap2/devices.c
index 990338f..a69bd67 100644
--- a/arch/arm/mach-omap2/devices.c
+++ b/arch/arm/mach-omap2/devices.c
@@ -63,7 +63,7 @@
WARN(IS_ERR(pdev), "could not build omap_device for %s\n", oh_name);
- return PTR_RET(pdev);
+ return PTR_ERR_OR_ZERO(pdev);
}
omap_postcore_initcall(omap3_l3_init);
@@ -333,6 +333,6 @@
pdev = omap_device_build("omap-gpmc", -1, oh, NULL, 0);
WARN(IS_ERR(pdev), "could not build omap_device for %s\n", oh_name);
- return PTR_RET(pdev);
+ return PTR_ERR_OR_ZERO(pdev);
}
omap_postcore_initcall(omap_gpmc_init);
diff --git a/arch/arm/mach-omap2/fb.c b/arch/arm/mach-omap2/fb.c
index 26e28e9..1f1ecf8 100644
--- a/arch/arm/mach-omap2/fb.c
+++ b/arch/arm/mach-omap2/fb.c
@@ -84,7 +84,7 @@
pdev = platform_device_register_resndata(NULL, "omapvrfb", -1,
res, num_res, NULL, 0);
- return PTR_RET(pdev);
+ return PTR_ERR_OR_ZERO(pdev);
}
#else
int __init omap_init_vrfb(void) { return 0; }
diff --git a/arch/arm/mach-omap2/gpmc-onenand.c b/arch/arm/mach-omap2/gpmc-onenand.c
index f899e77..17a6f75 100644
--- a/arch/arm/mach-omap2/gpmc-onenand.c
+++ b/arch/arm/mach-omap2/gpmc-onenand.c
@@ -216,11 +216,11 @@
div = gpmc_calc_divider(min_gpmc_clk_period);
gpmc_clk_ns = gpmc_ticks_to_ns(div);
- if (gpmc_clk_ns < 15) /* >66Mhz */
+ if (gpmc_clk_ns < 15) /* >66MHz */
onenand_flags |= ONENAND_FLAG_HF;
else
onenand_flags &= ~ONENAND_FLAG_HF;
- if (gpmc_clk_ns < 12) /* >83Mhz */
+ if (gpmc_clk_ns < 12) /* >83MHz */
onenand_flags |= ONENAND_FLAG_VHF;
else
onenand_flags &= ~ONENAND_FLAG_VHF;
diff --git a/arch/arm/mach-omap2/hsmmc.c b/arch/arm/mach-omap2/hsmmc.c
index 9a8611a..cff079e 100644
--- a/arch/arm/mach-omap2/hsmmc.c
+++ b/arch/arm/mach-omap2/hsmmc.c
@@ -70,7 +70,7 @@
reg = omap_ctrl_readl(control_pbias_offset);
if (cpu_is_omap3630()) {
- /* Set MMC I/O to 52Mhz */
+ /* Set MMC I/O to 52MHz */
prog_io = omap_ctrl_readl(OMAP343X_CONTROL_PROG_IO1);
prog_io |= OMAP3630_PRG_SDMMC1_SPEEDCTRL;
omap_ctrl_writel(prog_io, OMAP343X_CONTROL_PROG_IO1);
diff --git a/arch/arm/mach-omap2/omap-wakeupgen.c b/arch/arm/mach-omap2/omap-wakeupgen.c
index 3b56722..8e52621 100644
--- a/arch/arm/mach-omap2/omap-wakeupgen.c
+++ b/arch/arm/mach-omap2/omap-wakeupgen.c
@@ -444,7 +444,7 @@
return irq_domain_alloc_irqs_parent(domain, virq, nr_irqs, &parent_args);
}
-static struct irq_domain_ops wakeupgen_domain_ops = {
+static const struct irq_domain_ops wakeupgen_domain_ops = {
.xlate = wakeupgen_domain_xlate,
.alloc = wakeupgen_domain_alloc,
.free = irq_domain_free_irqs_common,
diff --git a/arch/arm/mach-omap2/opp2430_data.c b/arch/arm/mach-omap2/opp2430_data.c
index 0e75ec3e..b2233b7 100644
--- a/arch/arm/mach-omap2/opp2430_data.c
+++ b/arch/arm/mach-omap2/opp2430_data.c
@@ -116,7 +116,7 @@
RATE_IN_243X},
/* PRCM-boot/bypass */
- {S13M, S13M, S13M, RB_CM_CLKSEL_MPU_VAL, /* 13Mhz */
+ {S13M, S13M, S13M, RB_CM_CLKSEL_MPU_VAL, /* 13MHz */
RB_CM_CLKSEL_DSP_VAL, RB_CM_CLKSEL_GFX_VAL,
RB_CM_CLKSEL1_CORE_VAL, MB_CM_CLKSEL1_PLL_13_VAL,
MX_CLKSEL2_PLL_2x_VAL, RB_CM_CLKSEL_MDM_VAL,
@@ -124,7 +124,7 @@
RATE_IN_243X},
/* PRCM-boot/bypass */
- {S12M, S12M, S12M, RB_CM_CLKSEL_MPU_VAL, /* 12Mhz */
+ {S12M, S12M, S12M, RB_CM_CLKSEL_MPU_VAL, /* 12MHz */
RB_CM_CLKSEL_DSP_VAL, RB_CM_CLKSEL_GFX_VAL,
RB_CM_CLKSEL1_CORE_VAL, MB_CM_CLKSEL1_PLL_12_VAL,
MX_CLKSEL2_PLL_2x_VAL, RB_CM_CLKSEL_MDM_VAL,
diff --git a/arch/arm/mach-omap2/pmu.c b/arch/arm/mach-omap2/pmu.c
index a69e9a3..d2adfeb 100644
--- a/arch/arm/mach-omap2/pmu.c
+++ b/arch/arm/mach-omap2/pmu.c
@@ -55,7 +55,7 @@
WARN(IS_ERR(omap_pmu_dev), "Can't build omap_device for %s.\n",
dev_name);
- return PTR_RET(omap_pmu_dev);
+ return PTR_ERR_OR_ZERO(omap_pmu_dev);
}
static int __init omap_init_pmu(void)
diff --git a/arch/arm/mach-omap2/sdrc2xxx.c b/arch/arm/mach-omap2/sdrc2xxx.c
index ae3f155..339b0ec 100644
--- a/arch/arm/mach-omap2/sdrc2xxx.c
+++ b/arch/arm/mach-omap2/sdrc2xxx.c
@@ -164,6 +164,6 @@
mem_timings.slow_dll_ctrl |=
((mem_timings.fast_dll_ctrl & 0xF) | (1 << 2));
- /* 90 degree phase for anything below 133Mhz + disable DLL filter */
+ /* 90 degree phase for anything below 133MHz + disable DLL filter */
mem_timings.slow_dll_ctrl |= ((1 << 1) | (3 << 8));
}
diff --git a/arch/arm/mach-omap2/serial.c b/arch/arm/mach-omap2/serial.c
index 57dee0c..5fb50fe 100644
--- a/arch/arm/mach-omap2/serial.c
+++ b/arch/arm/mach-omap2/serial.c
@@ -203,7 +203,7 @@
if (cmdline_find_option(uart_name)) {
console_uart_id = uart->num;
- if (console_loglevel >= 10) {
+ if (console_loglevel >= CONSOLE_LOGLEVEL_DEBUG) {
uart_debug = true;
pr_info("%s used as console in debug mode: uart%d clocks will not be gated",
uart_name, uart->num);
diff --git a/arch/arm/mach-omap2/sram242x.S b/arch/arm/mach-omap2/sram242x.S
index 2c88ff2..53a2537 100644
--- a/arch/arm/mach-omap2/sram242x.S
+++ b/arch/arm/mach-omap2/sram242x.S
@@ -64,7 +64,7 @@
mvn r9, #0x4 @ mask to get clear bit2
and r10, r10, r9 @ clear bit2 for lock mode.
orr r10, r10, #0x8 @ make sure DLL on (es2 bit pos)
- orr r10, r10, #0x2 @ 90 degree phase for all below 133Mhz
+ orr r10, r10, #0x2 @ 90 degree phase for all below 133MHz
str r10, [r11] @ commit to DLLA_CTRL
bl i_dll_wait @ wait for dll to lock
diff --git a/arch/arm/mach-omap2/sram243x.S b/arch/arm/mach-omap2/sram243x.S
index d5deb97..b3edd6f 100644
--- a/arch/arm/mach-omap2/sram243x.S
+++ b/arch/arm/mach-omap2/sram243x.S
@@ -64,7 +64,7 @@
mvn r9, #0x4 @ mask to get clear bit2
and r10, r10, r9 @ clear bit2 for lock mode.
orr r10, r10, #0x8 @ make sure DLL on (es2 bit pos)
- orr r10, r10, #0x2 @ 90 degree phase for all below 133Mhz
+ orr r10, r10, #0x2 @ 90 degree phase for all below 133MHz
str r10, [r11] @ commit to DLLA_CTRL
bl i_dll_wait @ wait for dll to lock
diff --git a/arch/arm/mach-prima2/headsmp.S b/arch/arm/mach-prima2/headsmp.S
index d86fe33..209d9fc 100644
--- a/arch/arm/mach-prima2/headsmp.S
+++ b/arch/arm/mach-prima2/headsmp.S
@@ -15,7 +15,6 @@
* ready for them to initialise.
*/
ENTRY(sirfsoc_secondary_startup)
- bl v7_invalidate_l1
mrc p15, 0, r0, c0, c0, 5
and r0, r0, #15
adr r4, 1f
diff --git a/arch/arm/mach-pxa/mp900.c b/arch/arm/mach-pxa/mp900.c
index 854f1f5..14f6aaf 100644
--- a/arch/arm/mach-pxa/mp900.c
+++ b/arch/arm/mach-pxa/mp900.c
@@ -28,7 +28,7 @@
static void isp116x_pfm_delay(struct device *dev, int delay)
{
- /* 400Mhz PXA2 = 2.5ns / instruction */
+ /* 400MHz PXA2 = 2.5ns / instruction */
int cyc = delay / 10;
diff --git a/arch/arm/mach-rockchip/core.h b/arch/arm/mach-rockchip/core.h
index 39bca96..492c048 100644
--- a/arch/arm/mach-rockchip/core.h
+++ b/arch/arm/mach-rockchip/core.h
@@ -17,4 +17,3 @@
extern char rockchip_secondary_trampoline_end;
extern unsigned long rockchip_boot_fn;
-extern void rockchip_secondary_startup(void);
diff --git a/arch/arm/mach-rockchip/headsmp.S b/arch/arm/mach-rockchip/headsmp.S
index 46c22de..d69708b 100644
--- a/arch/arm/mach-rockchip/headsmp.S
+++ b/arch/arm/mach-rockchip/headsmp.S
@@ -15,14 +15,6 @@
#include <linux/linkage.h>
#include <linux/init.h>
-ENTRY(rockchip_secondary_startup)
- mrc p15, 0, r0, c0, c0, 0 @ read main ID register
- ldr r1, =0x00000c09 @ Cortex-A9 primary part number
- teq r0, r1
- beq v7_invalidate_l1
- b secondary_startup
-ENDPROC(rockchip_secondary_startup)
-
ENTRY(rockchip_secondary_trampoline)
ldr pc, 1f
ENDPROC(rockchip_secondary_trampoline)
diff --git a/arch/arm/mach-rockchip/platsmp.c b/arch/arm/mach-rockchip/platsmp.c
index 5b4ca3c..2e6ab67 100644
--- a/arch/arm/mach-rockchip/platsmp.c
+++ b/arch/arm/mach-rockchip/platsmp.c
@@ -149,8 +149,7 @@
* sram_base_addr + 8: start address for pc
* */
udelay(10);
- writel(virt_to_phys(rockchip_secondary_startup),
- sram_base_addr + 8);
+ writel(virt_to_phys(secondary_startup), sram_base_addr + 8);
writel(0xDEADBEAF, sram_base_addr + 4);
dsb_sev();
}
@@ -189,7 +188,7 @@
}
/* set the boot function for the sram code */
- rockchip_boot_fn = virt_to_phys(rockchip_secondary_startup);
+ rockchip_boot_fn = virt_to_phys(secondary_startup);
/* copy the trampoline to sram, that runs during startup of the core */
memcpy(sram_base_addr, &rockchip_secondary_trampoline, trampoline_sz);
diff --git a/arch/arm/mach-shmobile/common.h b/arch/arm/mach-shmobile/common.h
index afc60ba..476092b 100644
--- a/arch/arm/mach-shmobile/common.h
+++ b/arch/arm/mach-shmobile/common.h
@@ -14,7 +14,6 @@
extern void shmobile_smp_hook(unsigned int cpu, unsigned long fn,
unsigned long arg);
extern int shmobile_smp_cpu_disable(unsigned int cpu);
-extern void shmobile_invalidate_start(void);
extern void shmobile_boot_scu(void);
extern void shmobile_smp_scu_prepare_cpus(unsigned int max_cpus);
extern void shmobile_smp_scu_cpu_die(unsigned int cpu);
diff --git a/arch/arm/mach-shmobile/headsmp-scu.S b/arch/arm/mach-shmobile/headsmp-scu.S
index 69df8bf..fa5248c 100644
--- a/arch/arm/mach-shmobile/headsmp-scu.S
+++ b/arch/arm/mach-shmobile/headsmp-scu.S
@@ -22,7 +22,7 @@
* Boot code for secondary CPUs.
*
* First we turn on L1 cache coherency for our CPU. Then we jump to
- * shmobile_invalidate_start that invalidates the cache and hands over control
+ * secondary_startup that invalidates the cache and hands over control
* to the common ARM startup code.
*/
ENTRY(shmobile_boot_scu)
@@ -36,7 +36,7 @@
bic r2, r2, r3 @ Clear bits of our CPU (Run Mode)
str r2, [r0, #8] @ write back
- b shmobile_invalidate_start
+ b secondary_startup
ENDPROC(shmobile_boot_scu)
.text
diff --git a/arch/arm/mach-shmobile/headsmp.S b/arch/arm/mach-shmobile/headsmp.S
index 50c4915..330c1fc 100644
--- a/arch/arm/mach-shmobile/headsmp.S
+++ b/arch/arm/mach-shmobile/headsmp.S
@@ -16,13 +16,6 @@
#include <asm/assembler.h>
#include <asm/memory.h>
-#ifdef CONFIG_SMP
-ENTRY(shmobile_invalidate_start)
- bl v7_invalidate_l1
- b secondary_startup
-ENDPROC(shmobile_invalidate_start)
-#endif
-
/*
* Reset vector for secondary CPUs.
* This will be mapped at address 0 by SBAR register.
diff --git a/arch/arm/mach-shmobile/platsmp-apmu.c b/arch/arm/mach-shmobile/platsmp-apmu.c
index f483b56..b0790fc 100644
--- a/arch/arm/mach-shmobile/platsmp-apmu.c
+++ b/arch/arm/mach-shmobile/platsmp-apmu.c
@@ -133,7 +133,7 @@
int shmobile_smp_apmu_boot_secondary(unsigned int cpu, struct task_struct *idle)
{
/* For this particular CPU register boot vector */
- shmobile_smp_hook(cpu, virt_to_phys(shmobile_invalidate_start), 0);
+ shmobile_smp_hook(cpu, virt_to_phys(secondary_startup), 0);
return apmu_wrap(cpu, apmu_power_on);
}
diff --git a/arch/arm/mach-socfpga/core.h b/arch/arm/mach-socfpga/core.h
index a0f3b1c..767c09e 100644
--- a/arch/arm/mach-socfpga/core.h
+++ b/arch/arm/mach-socfpga/core.h
@@ -31,7 +31,6 @@
#define RSTMGR_MPUMODRST_CPU1 0x2 /* CPU1 Reset */
-extern void socfpga_secondary_startup(void);
extern void __iomem *socfpga_scu_base_addr;
extern void socfpga_init_clocks(void);
diff --git a/arch/arm/mach-socfpga/headsmp.S b/arch/arm/mach-socfpga/headsmp.S
index f65ea0a..5bb0164 100644
--- a/arch/arm/mach-socfpga/headsmp.S
+++ b/arch/arm/mach-socfpga/headsmp.S
@@ -30,8 +30,3 @@
1: .long .
.long socfpga_cpu1start_addr
ENTRY(secondary_trampoline_end)
-
-ENTRY(socfpga_secondary_startup)
- bl v7_invalidate_l1
- b secondary_startup
-ENDPROC(socfpga_secondary_startup)
diff --git a/arch/arm/mach-socfpga/platsmp.c b/arch/arm/mach-socfpga/platsmp.c
index c64d89b..79c5336 100644
--- a/arch/arm/mach-socfpga/platsmp.c
+++ b/arch/arm/mach-socfpga/platsmp.c
@@ -40,7 +40,7 @@
memcpy(phys_to_virt(0), &secondary_trampoline, trampoline_size);
- writel(virt_to_phys(socfpga_secondary_startup),
+ writel(virt_to_phys(secondary_startup),
sys_manager_base_addr + (socfpga_cpu1start_addr & 0x000000ff));
flush_cache_all();
diff --git a/arch/arm/mach-tegra/Makefile b/arch/arm/mach-tegra/Makefile
index e48a744..fffad24 100644
--- a/arch/arm/mach-tegra/Makefile
+++ b/arch/arm/mach-tegra/Makefile
@@ -19,7 +19,7 @@
ifeq ($(CONFIG_CPU_IDLE),y)
obj-$(CONFIG_ARCH_TEGRA_3x_SOC) += cpuidle-tegra30.o
endif
-obj-$(CONFIG_SMP) += platsmp.o headsmp.o
+obj-$(CONFIG_SMP) += platsmp.o
obj-$(CONFIG_HOTPLUG_CPU) += hotplug.o
obj-$(CONFIG_ARCH_TEGRA_114_SOC) += sleep-tegra30.o
diff --git a/arch/arm/mach-tegra/headsmp.S b/arch/arm/mach-tegra/headsmp.S
deleted file mode 100644
index 2072e73..0000000
--- a/arch/arm/mach-tegra/headsmp.S
+++ /dev/null
@@ -1,12 +0,0 @@
-#include <linux/linkage.h>
-#include <linux/init.h>
-
-#include "sleep.h"
-
- .section ".text.head", "ax"
-
-ENTRY(tegra_secondary_startup)
- check_cpu_part_num 0xc09, r8, r9
- bleq v7_invalidate_l1
- b secondary_startup
-ENDPROC(tegra_secondary_startup)
diff --git a/arch/arm/mach-tegra/reset.c b/arch/arm/mach-tegra/reset.c
index 894c5c4..6fd9db5 100644
--- a/arch/arm/mach-tegra/reset.c
+++ b/arch/arm/mach-tegra/reset.c
@@ -94,7 +94,7 @@
__tegra_cpu_reset_handler_data[TEGRA_RESET_MASK_PRESENT] =
*((u32 *)cpu_possible_mask);
__tegra_cpu_reset_handler_data[TEGRA_RESET_STARTUP_SECONDARY] =
- virt_to_phys((void *)tegra_secondary_startup);
+ virt_to_phys((void *)secondary_startup);
#endif
#ifdef CONFIG_PM_SLEEP
diff --git a/arch/arm/mach-tegra/reset.h b/arch/arm/mach-tegra/reset.h
index 76a9343..0aee012 100644
--- a/arch/arm/mach-tegra/reset.h
+++ b/arch/arm/mach-tegra/reset.h
@@ -36,7 +36,6 @@
void __tegra_cpu_reset_handler_start(void);
void __tegra_cpu_reset_handler(void);
void __tegra_cpu_reset_handler_end(void);
-void tegra_secondary_startup(void);
#ifdef CONFIG_PM_SLEEP
#define tegra_cpu_lp1_mask \
diff --git a/arch/arm/mach-tegra/sleep-tegra30.S b/arch/arm/mach-tegra/sleep-tegra30.S
index 5d8d13a..9a2f0b0 100644
--- a/arch/arm/mach-tegra/sleep-tegra30.S
+++ b/arch/arm/mach-tegra/sleep-tegra30.S
@@ -223,7 +223,7 @@
b __cpu_reset_again
/*
- * 38 nop's, which fills reset of wfe cache line and
+ * 38 nop's, which fills rest of wfe cache line and
* 4 more cachelines with nop
*/
.rept 38
diff --git a/arch/arm/mach-ux500/cache-l2x0.c b/arch/arm/mach-ux500/cache-l2x0.c
index e97ee55..7557bed 100644
--- a/arch/arm/mach-ux500/cache-l2x0.c
+++ b/arch/arm/mach-ux500/cache-l2x0.c
@@ -6,6 +6,7 @@
#include <linux/io.h>
#include <linux/of.h>
+#include <linux/of_address.h>
#include <asm/hardware/cache-l2x0.h>
@@ -15,7 +16,14 @@
static int __init ux500_l2x0_unlock(void)
{
int i;
- void __iomem *l2x0_base = __io_address(U8500_L2CC_BASE);
+ struct device_node *np;
+ void __iomem *l2x0_base;
+
+ np = of_find_compatible_node(NULL, NULL, "arm,pl310-cache");
+ l2x0_base = of_iomap(np, 0);
+ of_node_put(np);
+ if (!l2x0_base)
+ return -ENODEV;
/*
* Unlock Data and Instruction Lock if locked. Ux500 U-Boot versions
@@ -30,6 +38,7 @@
writel_relaxed(0x0, l2x0_base + L2X0_LOCKDOWN_WAY_I_BASE +
i * L2X0_LOCKDOWN_STRIDE);
}
+ iounmap(l2x0_base);
return 0;
}
diff --git a/arch/arm/mach-ux500/cpu-db8500.c b/arch/arm/mach-ux500/cpu-db8500.c
index 6f63954..1691380 100644
--- a/arch/arm/mach-ux500/cpu-db8500.c
+++ b/arch/arm/mach-ux500/cpu-db8500.c
@@ -43,60 +43,10 @@
.legacy_offset = DB8500_PRCMU_LEGACY_OFFSET,
};
-/* minimum static i/o mapping required to boot U8500 platforms */
-static struct map_desc u8500_uart_io_desc[] __initdata = {
- __IO_DEV_DESC(U8500_UART0_BASE, SZ_4K),
- __IO_DEV_DESC(U8500_UART2_BASE, SZ_4K),
-};
-/* U8500 and U9540 common io_desc */
-static struct map_desc u8500_common_io_desc[] __initdata = {
- /* SCU base also covers GIC CPU BASE and TWD with its 4K page */
- __IO_DEV_DESC(U8500_SCU_BASE, SZ_4K),
- __IO_DEV_DESC(U8500_GIC_DIST_BASE, SZ_4K),
- __IO_DEV_DESC(U8500_L2CC_BASE, SZ_4K),
- __IO_DEV_DESC(U8500_MTU0_BASE, SZ_4K),
- __IO_DEV_DESC(U8500_BACKUPRAM0_BASE, SZ_8K),
-
- __IO_DEV_DESC(U8500_CLKRST1_BASE, SZ_4K),
- __IO_DEV_DESC(U8500_CLKRST2_BASE, SZ_4K),
- __IO_DEV_DESC(U8500_CLKRST3_BASE, SZ_4K),
- __IO_DEV_DESC(U8500_CLKRST5_BASE, SZ_4K),
- __IO_DEV_DESC(U8500_CLKRST6_BASE, SZ_4K),
-
- __IO_DEV_DESC(U8500_GPIO0_BASE, SZ_4K),
- __IO_DEV_DESC(U8500_GPIO1_BASE, SZ_4K),
- __IO_DEV_DESC(U8500_GPIO2_BASE, SZ_4K),
- __IO_DEV_DESC(U8500_GPIO3_BASE, SZ_4K),
-};
-
-/* U8500 IO map specific description */
-static struct map_desc u8500_io_desc[] __initdata = {
- __IO_DEV_DESC(U8500_PRCMU_BASE, SZ_4K),
- __IO_DEV_DESC(U8500_PRCMU_TCDM_BASE, SZ_4K),
-
-};
-
-/* U9540 IO map specific description */
-static struct map_desc u9540_io_desc[] __initdata = {
- __IO_DEV_DESC(U8500_PRCMU_BASE, SZ_4K + SZ_8K),
- __IO_DEV_DESC(U8500_PRCMU_TCDM_BASE, SZ_4K + SZ_8K),
-};
-
static void __init u8500_map_io(void)
{
- /*
- * Map the UARTs early so that the DEBUG_LL stuff continues to work.
- */
- iotable_init(u8500_uart_io_desc, ARRAY_SIZE(u8500_uart_io_desc));
-
- ux500_map_io();
-
- iotable_init(u8500_common_io_desc, ARRAY_SIZE(u8500_common_io_desc));
-
- if (cpu_is_ux540_family())
- iotable_init(u9540_io_desc, ARRAY_SIZE(u9540_io_desc));
- else
- iotable_init(u8500_io_desc, ARRAY_SIZE(u8500_io_desc));
+ debug_ll_io_init();
+ ux500_setup_id();
}
/*
@@ -125,14 +75,18 @@
static const char *db8500_read_soc_id(void)
{
- void __iomem *uid = __io_address(U8500_BB_UID_BASE);
+ void __iomem *uid;
+ uid = ioremap(U8500_BB_UID_BASE, 0x20);
+ if (!uid)
+ return NULL;
/* Throw these device-specific numbers into the entropy pool */
add_device_randomness(uid, 0x14);
return kasprintf(GFP_KERNEL, "%08x%08x%08x%08x%08x",
readl((u32 *)uid+0),
readl((u32 *)uid+1), readl((u32 *)uid+2),
readl((u32 *)uid+3), readl((u32 *)uid+4));
+ iounmap(uid);
}
static struct device * __init db8500_soc_device_init(void)
diff --git a/arch/arm/mach-ux500/cpu.c b/arch/arm/mach-ux500/cpu.c
index 6ced0f68..e31d3d6 100644
--- a/arch/arm/mach-ux500/cpu.c
+++ b/arch/arm/mach-ux500/cpu.c
@@ -16,6 +16,7 @@
#include <linux/stat.h>
#include <linux/of.h>
#include <linux/of_irq.h>
+#include <linux/of_address.h>
#include <linux/irq.h>
#include <linux/irqchip.h>
#include <linux/irqchip/arm-gic.h>
@@ -52,31 +53,36 @@
*/
void __init ux500_init_irq(void)
{
+ struct device_node *np;
+ struct resource r;
+
gic_set_irqchip_flags(IRQCHIP_SKIP_SET_WAKE | IRQCHIP_MASK_ON_SUSPEND);
irqchip_init();
+ np = of_find_compatible_node(NULL, NULL, "stericsson,db8500-prcmu");
+ of_address_to_resource(np, 0, &r);
+ of_node_put(np);
+ if (!r.start) {
+ pr_err("could not find PRCMU base resource\n");
+ return;
+ }
+ prcmu_early_init(r.start, r.end-r.start);
+ ux500_pm_init(r.start, r.end-r.start);
/*
* Init clocks here so that they are available for system timer
* initialization.
*/
if (cpu_is_u8500_family()) {
- prcmu_early_init(U8500_PRCMU_BASE, SZ_8K - 1);
- ux500_pm_init(U8500_PRCMU_BASE, SZ_8K - 1);
-
u8500_of_clk_init(U8500_CLKRST1_BASE,
U8500_CLKRST2_BASE,
U8500_CLKRST3_BASE,
U8500_CLKRST5_BASE,
U8500_CLKRST6_BASE);
} else if (cpu_is_u9540()) {
- prcmu_early_init(U8500_PRCMU_BASE, SZ_8K - 1);
- ux500_pm_init(U8500_PRCMU_BASE, SZ_8K - 1);
u9540_clk_init(U8500_CLKRST1_BASE, U8500_CLKRST2_BASE,
U8500_CLKRST3_BASE, U8500_CLKRST5_BASE,
U8500_CLKRST6_BASE);
} else if (cpu_is_u8540()) {
- prcmu_early_init(U8500_PRCMU_BASE, SZ_8K + SZ_4K - 1);
- ux500_pm_init(U8500_PRCMU_BASE, SZ_8K + SZ_4K - 1);
u8540_clk_init(U8500_CLKRST1_BASE, U8500_CLKRST2_BASE,
U8500_CLKRST3_BASE, U8500_CLKRST5_BASE,
U8500_CLKRST6_BASE);
diff --git a/arch/arm/mach-ux500/id.c b/arch/arm/mach-ux500/id.c
index 392f2fd..1e81e99 100644
--- a/arch/arm/mach-ux500/id.c
+++ b/arch/arm/mach-ux500/id.c
@@ -72,7 +72,7 @@
* DB9540 0x413fc090 0xFFFFDBF4 0x009540xx
*/
-void __init ux500_map_io(void)
+void __init ux500_setup_id(void)
{
unsigned int cpuid = read_cpuid_id();
unsigned int asicid = 0;
diff --git a/arch/arm/mach-ux500/platsmp.c b/arch/arm/mach-ux500/platsmp.c
index a44967f..62b1de9 100644
--- a/arch/arm/mach-ux500/platsmp.c
+++ b/arch/arm/mach-ux500/platsmp.c
@@ -16,6 +16,8 @@
#include <linux/device.h>
#include <linux/smp.h>
#include <linux/io.h>
+#include <linux/of.h>
+#include <linux/of_address.h>
#include <asm/cacheflush.h>
#include <asm/smp_plat.h>
@@ -26,6 +28,9 @@
#include "db8500-regs.h"
#include "id.h"
+static void __iomem *scu_base;
+static void __iomem *backupram;
+
/* This is called from headsmp.S to wakeup the secondary core */
extern void u8500_secondary_startup(void);
@@ -41,16 +46,6 @@
sync_cache_w(&pen_release);
}
-static void __iomem *scu_base_addr(void)
-{
- if (cpu_is_u8500_family() || cpu_is_ux540_family())
- return __io_address(U8500_SCU_BASE);
- else
- ux500_unknown_soc();
-
- return NULL;
-}
-
static DEFINE_SPINLOCK(boot_lock);
static void ux500_secondary_init(unsigned int cpu)
@@ -104,13 +99,6 @@
static void __init wakeup_secondary(void)
{
- void __iomem *backupram;
-
- if (cpu_is_u8500_family() || cpu_is_ux540_family())
- backupram = __io_address(U8500_BACKUPRAM0_BASE);
- else
- ux500_unknown_soc();
-
/*
* write the address of secondary startup into the backup ram register
* at offset 0x1FF4, then write the magic number 0xA1FEED01 to the
@@ -135,10 +123,16 @@
*/
static void __init ux500_smp_init_cpus(void)
{
- void __iomem *scu_base = scu_base_addr();
unsigned int i, ncores;
+ struct device_node *np;
- ncores = scu_base ? scu_get_core_count(scu_base) : 1;
+ np = of_find_compatible_node(NULL, NULL, "arm,cortex-a9-scu");
+ scu_base = of_iomap(np, 0);
+ of_node_put(np);
+ if (!scu_base)
+ return;
+ backupram = ioremap(U8500_BACKUPRAM0_BASE, SZ_8K);
+ ncores = scu_get_core_count(scu_base);
/* sanity check */
if (ncores > nr_cpu_ids) {
@@ -153,8 +147,7 @@
static void __init ux500_smp_prepare_cpus(unsigned int max_cpus)
{
-
- scu_enable(scu_base_addr());
+ scu_enable(scu_base);
wakeup_secondary();
}
diff --git a/arch/arm/mach-ux500/pm.c b/arch/arm/mach-ux500/pm.c
index 2cb587b..8538910 100644
--- a/arch/arm/mach-ux500/pm.c
+++ b/arch/arm/mach-ux500/pm.c
@@ -15,6 +15,8 @@
#include <linux/io.h>
#include <linux/suspend.h>
#include <linux/platform_data/arm-ux500-pm.h>
+#include <linux/of.h>
+#include <linux/of_address.h>
#include "db8500-regs.h"
#include "pm_domains.h"
@@ -42,6 +44,7 @@
#define PRCM_ARMITVAL127TO96 (prcmu_base + 0x26C)
static void __iomem *prcmu_base;
+static void __iomem *dist_base;
/* This function decouple the gic from the prcmu */
int prcmu_gic_decouple(void)
@@ -88,7 +91,6 @@
{
u32 pr; /* Pending register */
u32 er; /* Enable register */
- void __iomem *dist_base = __io_address(U8500_GIC_DIST_BASE);
int i;
/* 5 registers. STI & PPI not skipped */
@@ -143,7 +145,6 @@
int prcmu_copy_gic_settings(void)
{
u32 er; /* Enable register */
- void __iomem *dist_base = __io_address(U8500_GIC_DIST_BASE);
int i;
/* We skip the STI and PPI */
@@ -179,11 +180,21 @@
void __init ux500_pm_init(u32 phy_base, u32 size)
{
+ struct device_node *np;
+
prcmu_base = ioremap(phy_base, size);
if (!prcmu_base) {
pr_err("could not remap PRCMU for PM functions\n");
return;
}
+ np = of_find_compatible_node(NULL, NULL, "arm,cortex-a9-gic");
+ dist_base = of_iomap(np, 0);
+ of_node_put(np);
+ if (!dist_base) {
+ pr_err("could not remap GIC dist base for PM functions\n");
+ return;
+ }
+
/*
* On watchdog reboot the GIC is in some cases decoupled.
* This will make sure that the GIC is correctly configured.
diff --git a/arch/arm/mach-ux500/setup.h b/arch/arm/mach-ux500/setup.h
index 2dea8b5..1fb6ad2 100644
--- a/arch/arm/mach-ux500/setup.h
+++ b/arch/arm/mach-ux500/setup.h
@@ -18,7 +18,7 @@
void ux500_restart(enum reboot_mode mode, const char *cmd);
-void __init ux500_map_io(void);
+void __init ux500_setup_id(void);
extern void __init ux500_init_irq(void);
@@ -26,20 +26,6 @@
extern void ux500_timer_init(void);
-#define __IO_DEV_DESC(x, sz) { \
- .virtual = IO_ADDRESS(x), \
- .pfn = __phys_to_pfn(x), \
- .length = sz, \
- .type = MT_DEVICE, \
-}
-
-#define __MEM_DEV_DESC(x, sz) { \
- .virtual = IO_ADDRESS(x), \
- .pfn = __phys_to_pfn(x), \
- .length = sz, \
- .type = MT_MEMORY_RWX, \
-}
-
extern struct smp_operations ux500_smp_ops;
extern void ux500_cpu_die(unsigned int cpu);
diff --git a/arch/arm/mach-zynq/common.h b/arch/arm/mach-zynq/common.h
index 382c60e..7038cae 100644
--- a/arch/arm/mach-zynq/common.h
+++ b/arch/arm/mach-zynq/common.h
@@ -17,8 +17,6 @@
#ifndef __MACH_ZYNQ_COMMON_H__
#define __MACH_ZYNQ_COMMON_H__
-void zynq_secondary_startup(void);
-
extern int zynq_slcr_init(void);
extern int zynq_early_slcr_init(void);
extern void zynq_slcr_system_reset(void);
diff --git a/arch/arm/mach-zynq/headsmp.S b/arch/arm/mach-zynq/headsmp.S
index dd8c071..045c727 100644
--- a/arch/arm/mach-zynq/headsmp.S
+++ b/arch/arm/mach-zynq/headsmp.S
@@ -22,8 +22,3 @@
.globl zynq_secondary_trampoline_end
zynq_secondary_trampoline_end:
ENDPROC(zynq_secondary_trampoline)
-
-ENTRY(zynq_secondary_startup)
- bl v7_invalidate_l1
- b secondary_startup
-ENDPROC(zynq_secondary_startup)
diff --git a/arch/arm/mach-zynq/platsmp.c b/arch/arm/mach-zynq/platsmp.c
index 52d768f..f66816c 100644
--- a/arch/arm/mach-zynq/platsmp.c
+++ b/arch/arm/mach-zynq/platsmp.c
@@ -87,10 +87,9 @@
}
EXPORT_SYMBOL(zynq_cpun_start);
-static int zynq_boot_secondary(unsigned int cpu,
- struct task_struct *idle)
+static int zynq_boot_secondary(unsigned int cpu, struct task_struct *idle)
{
- return zynq_cpun_start(virt_to_phys(zynq_secondary_startup), cpu);
+ return zynq_cpun_start(virt_to_phys(secondary_startup), cpu);
}
/*
diff --git a/arch/arm/mm/proc-v7.S b/arch/arm/mm/proc-v7.S
index 3d1054f..75ae721 100644
--- a/arch/arm/mm/proc-v7.S
+++ b/arch/arm/mm/proc-v7.S
@@ -336,7 +336,7 @@
__v7_setup:
adr r12, __v7_setup_stack @ the local stack
stmia r12, {r0-r5, r7, r9, r11, lr}
- bl v7_flush_dcache_louis
+ bl v7_invalidate_l1
ldmia r12, {r0-r5, r7, r9, r11, lr}
mrc p15, 0, r0, c0, c0, 0 @ read main ID register
diff --git a/arch/arm64/boot/dts/skeleton.dtsi b/arch/arm64/boot/dts/skeleton.dtsi
deleted file mode 100644
index 38ead82..0000000
--- a/arch/arm64/boot/dts/skeleton.dtsi
+++ /dev/null
@@ -1,13 +0,0 @@
-/*
- * Skeleton device tree; the bare minimum needed to boot; just include and
- * add a compatible value. The bootloader will typically populate the memory
- * node.
- */
-
-/ {
- #address-cells = <2>;
- #size-cells = <1>;
- chosen { };
- aliases { };
- memory { device_type = "memory"; reg = <0 0 0>; };
-};
diff --git a/drivers/ata/Kconfig b/drivers/ata/Kconfig
index b11470a..6d17a3b 100644
--- a/drivers/ata/Kconfig
+++ b/drivers/ata/Kconfig
@@ -845,7 +845,6 @@
config PATA_AT91
tristate "PATA support for AT91SAM9260"
depends on ARM && SOC_AT91SAM9
- depends on !ARCH_MULTIPLATFORM
help
This option enables support for IDE devices on the Atmel AT91SAM9260 SoC.
diff --git a/drivers/ata/pata_at91.c b/drivers/ata/pata_at91.c
index 9e85937..ace0a4d 100644
--- a/drivers/ata/pata_at91.c
+++ b/drivers/ata/pata_at91.c
@@ -24,11 +24,13 @@
#include <linux/ata.h>
#include <linux/clk.h>
#include <linux/libata.h>
+#include <linux/mfd/syscon.h>
+#include <linux/mfd/syscon/atmel-smc.h>
#include <linux/platform_device.h>
#include <linux/ata_platform.h>
#include <linux/platform_data/atmel.h>
+#include <linux/regmap.h>
-#include <mach/at91sam9_smc.h>
#include <asm/gpio.h>
#define DRV_NAME "pata_at91"
@@ -57,6 +59,15 @@
int max;
};
+struct regmap *smc;
+
+struct at91sam9_smc_generic_fields {
+ struct regmap_field *setup;
+ struct regmap_field *pulse;
+ struct regmap_field *cycle;
+ struct regmap_field *mode;
+} fields;
+
/**
* adjust_smc_value - adjust value for one of SMC registers.
* @value: adjusted value
@@ -206,7 +217,6 @@
{
int ret = 0;
int use_iordy;
- struct sam9_smc_config smc;
unsigned int t6z; /* data tristate time in ns */
unsigned int cycle; /* SMC Cycle width in MCK ticks */
unsigned int setup; /* SMC Setup width in MCK ticks */
@@ -244,19 +254,21 @@
dev_dbg(dev, "Use IORDY=%u, TDF Cycles=%u\n", use_iordy, tdf_cycles);
- /* SMC Setup Register */
- smc.nwe_setup = smc.nrd_setup = setup;
- smc.ncs_write_setup = smc.ncs_read_setup = 0;
- /* SMC Pulse Register */
- smc.nwe_pulse = smc.nrd_pulse = pulse;
- smc.ncs_write_pulse = smc.ncs_read_pulse = cs_pulse;
- /* SMC Cycle Register */
- smc.write_cycle = smc.read_cycle = cycle;
- /* SMC Mode Register*/
- smc.tdf_cycles = tdf_cycles;
- smc.mode = info->mode;
-
- sam9_smc_configure(0, info->cs, &smc);
+ regmap_fields_write(fields.setup, info->cs,
+ AT91SAM9_SMC_NRDSETUP(setup) |
+ AT91SAM9_SMC_NWESETUP(setup) |
+ AT91SAM9_SMC_NCS_NRDSETUP(0) |
+ AT91SAM9_SMC_NCS_WRSETUP(0));
+ regmap_fields_write(fields.pulse, info->cs,
+ AT91SAM9_SMC_NRDPULSE(pulse) |
+ AT91SAM9_SMC_NWEPULSE(pulse) |
+ AT91SAM9_SMC_NCS_NRDPULSE(cs_pulse) |
+ AT91SAM9_SMC_NCS_WRPULSE(cs_pulse));
+ regmap_fields_write(fields.cycle, info->cs,
+ AT91SAM9_SMC_NRDCYCLE(cycle) |
+ AT91SAM9_SMC_NWECYCLE(cycle));
+ regmap_fields_write(fields.mode, info->cs, info->mode |
+ AT91_SMC_TDF_(tdf_cycles));
}
static void pata_at91_set_piomode(struct ata_port *ap, struct ata_device *adev)
@@ -280,21 +292,21 @@
{
struct at91_ide_info *info = dev->link->ap->host->private_data;
unsigned int consumed;
+ unsigned int mode;
unsigned long flags;
- struct sam9_smc_config smc;
local_irq_save(flags);
- sam9_smc_read_mode(0, info->cs, &smc);
+ regmap_fields_read(fields.mode, info->cs, &mode);
/* set 16bit mode before writing data */
- smc.mode = (smc.mode & ~AT91_SMC_DBW) | AT91_SMC_DBW_16;
- sam9_smc_write_mode(0, info->cs, &smc);
+ regmap_fields_write(fields.mode, info->cs, (mode & ~AT91_SMC_DBW) |
+ AT91_SMC_DBW_16);
consumed = ata_sff_data_xfer(dev, buf, buflen, rw);
/* restore 8bit mode after data is written */
- smc.mode = (smc.mode & ~AT91_SMC_DBW) | AT91_SMC_DBW_8;
- sam9_smc_write_mode(0, info->cs, &smc);
+ regmap_fields_write(fields.mode, info->cs, (mode & ~AT91_SMC_DBW) |
+ AT91_SMC_DBW_8);
local_irq_restore(flags);
return consumed;
@@ -312,6 +324,36 @@
.cable_detect = ata_cable_40wire,
};
+static int at91sam9_smc_fields_init(struct device *dev)
+{
+ struct reg_field field = REG_FIELD(0, 0, 31);
+
+ field.id_size = 8;
+ field.id_offset = AT91SAM9_SMC_GENERIC_BLK_SZ;
+
+ field.reg = AT91SAM9_SMC_SETUP(AT91SAM9_SMC_GENERIC);
+ fields.setup = devm_regmap_field_alloc(dev, smc, field);
+ if (IS_ERR(fields.setup))
+ return PTR_ERR(fields.setup);
+
+ field.reg = AT91SAM9_SMC_PULSE(AT91SAM9_SMC_GENERIC);
+ fields.pulse = devm_regmap_field_alloc(dev, smc, field);
+ if (IS_ERR(fields.pulse))
+ return PTR_ERR(fields.pulse);
+
+ field.reg = AT91SAM9_SMC_CYCLE(AT91SAM9_SMC_GENERIC);
+ fields.cycle = devm_regmap_field_alloc(dev, smc, field);
+ if (IS_ERR(fields.cycle))
+ return PTR_ERR(fields.cycle);
+
+ field.reg = AT91SAM9_SMC_MODE(AT91SAM9_SMC_GENERIC);
+ fields.mode = devm_regmap_field_alloc(dev, smc, field);
+ if (IS_ERR(fields.mode))
+ return PTR_ERR(fields.mode);
+
+ return 0;
+}
+
static int pata_at91_probe(struct platform_device *pdev)
{
struct at91_cf_data *board = dev_get_platdata(&pdev->dev);
@@ -341,6 +383,14 @@
irq = board->irq_pin;
+ smc = syscon_regmap_lookup_by_phandle(pdev->dev.of_node, "atmel,smc");
+ if (IS_ERR(smc))
+ return PTR_ERR(smc);
+
+ ret = at91sam9_smc_fields_init(dev);
+ if (ret < 0)
+ return ret;
+
/* init ata host */
host = ata_host_alloc(dev, 1);
diff --git a/drivers/pcmcia/Kconfig b/drivers/pcmcia/Kconfig
index a65f821..d3c378b 100644
--- a/drivers/pcmcia/Kconfig
+++ b/drivers/pcmcia/Kconfig
@@ -277,7 +277,6 @@
tristate "AT91 CompactFlash Controller"
depends on PCI
depends on PCMCIA && ARCH_AT91
- depends on !ARCH_MULTIPLATFORM
help
Say Y here to support the CompactFlash controller on AT91 chips.
Or choose M to compile the driver as a module named "at91_cf".
diff --git a/drivers/pcmcia/at91_cf.c b/drivers/pcmcia/at91_cf.c
index e7775a4..87147bc 100644
--- a/drivers/pcmcia/at91_cf.c
+++ b/drivers/pcmcia/at91_cf.c
@@ -20,16 +20,15 @@
#include <linux/platform_data/atmel.h>
#include <linux/io.h>
#include <linux/sizes.h>
+#include <linux/mfd/syscon.h>
+#include <linux/mfd/syscon/atmel-mc.h>
#include <linux/of.h>
#include <linux/of_device.h>
#include <linux/of_gpio.h>
+#include <linux/regmap.h>
#include <pcmcia/ss.h>
-#include <mach/at91rm9200_mc.h>
-#include <mach/at91_ramc.h>
-
-
/*
* A0..A10 work in each range; A23 indicates I/O space; A25 is CFRNW;
* some other bit in {A24,A22..A11} is nREG to flag memory access
@@ -40,6 +39,8 @@
#define CF_IO_PHYS (1 << 23)
#define CF_MEM_PHYS (0x017ff800)
+struct regmap *mc;
+
/*--------------------------------------------------------------------------*/
struct at91_cf_socket {
@@ -155,10 +156,7 @@
/*
* Use 16 bit accesses unless/until we need 8-bit i/o space.
- */
- csr = at91_ramc_read(0, AT91_SMC_CSR(cf->board->chipselect)) & ~AT91_SMC_DBW;
-
- /*
+ *
* NOTE: this CF controller ignores IOIS16, so we can't really do
* MAP_AUTOSZ. The 16bit mode allows single byte access on either
* D0-D7 (even addr) or D8-D15 (odd), so it's close enough for many
@@ -169,13 +167,14 @@
* CF 3.0 spec table 35 also giving the D8-D15 option.
*/
if (!(io->flags & (MAP_16BIT | MAP_AUTOSZ))) {
- csr |= AT91_SMC_DBW_8;
+ csr = AT91_MC_SMC_DBW_8;
dev_dbg(&cf->pdev->dev, "8bit i/o bus\n");
} else {
- csr |= AT91_SMC_DBW_16;
+ csr = AT91_MC_SMC_DBW_16;
dev_dbg(&cf->pdev->dev, "16bit i/o bus\n");
}
- at91_ramc_write(0, AT91_SMC_CSR(cf->board->chipselect), csr);
+ regmap_update_bits(mc, AT91_MC_SMC_CSR(cf->board->chipselect),
+ AT91_MC_SMC_DBW, csr);
io->start = cf->socket.io_offset;
io->stop = io->start + SZ_2K - 1;
@@ -236,6 +235,10 @@
pdev->dev.platform_data = board;
+ mc = syscon_regmap_lookup_by_compatible("atmel,at91rm9200-sdramc");
+ if (IS_ERR(mc))
+ return PTR_ERR(mc);
+
return 0;
}
#else
diff --git a/include/linux/mfd/syscon/atmel-mc.h b/include/linux/mfd/syscon/atmel-mc.h
new file mode 100644
index 0000000..afd9b8f
--- /dev/null
+++ b/include/linux/mfd/syscon/atmel-mc.h
@@ -0,0 +1,144 @@
+/*
+ * Copyright (C) 2005 Ivan Kokshaysky
+ * Copyright (C) SAN People
+ *
+ * Memory Controllers (MC, EBI, SMC, SDRAMC, BFC) - System peripherals
+ * registers.
+ * Based on AT91RM9200 datasheet revision E.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#ifndef _LINUX_MFD_SYSCON_ATMEL_MC_H_
+#define _LINUX_MFD_SYSCON_ATMEL_MC_H_
+
+/* Memory Controller */
+#define AT91_MC_RCR 0x00
+#define AT91_MC_RCB BIT(0)
+
+#define AT91_MC_ASR 0x04
+#define AT91_MC_UNADD BIT(0)
+#define AT91_MC_MISADD BIT(1)
+#define AT91_MC_ABTSZ GENMASK(9, 8)
+#define AT91_MC_ABTSZ_BYTE (0 << 8)
+#define AT91_MC_ABTSZ_HALFWORD (1 << 8)
+#define AT91_MC_ABTSZ_WORD (2 << 8)
+#define AT91_MC_ABTTYP GENMASK(11, 10)
+#define AT91_MC_ABTTYP_DATAREAD (0 << 10)
+#define AT91_MC_ABTTYP_DATAWRITE (1 << 10)
+#define AT91_MC_ABTTYP_FETCH (2 << 10)
+#define AT91_MC_MST(n) BIT(16 + (n))
+#define AT91_MC_SVMST(n) BIT(24 + (n))
+
+#define AT91_MC_AASR 0x08
+
+#define AT91_MC_MPR 0x0c
+#define AT91_MPR_MSTP(n) GENMASK(2 + ((x) * 4), ((x) * 4))
+
+/* External Bus Interface (EBI) registers */
+#define AT91_MC_EBI_CSA 0x60
+#define AT91_MC_EBI_CS(n) BIT(x)
+#define AT91_MC_EBI_NUM_CS 8
+
+#define AT91_MC_EBI_CFGR 0x64
+#define AT91_MC_EBI_DBPUC BIT(0)
+
+/* Static Memory Controller (SMC) registers */
+#define AT91_MC_SMC_CSR(n) (0x70 + ((n) * 4))
+#define AT91_MC_SMC_NWS GENMASK(6, 0)
+#define AT91_MC_SMC_NWS_(x) ((x) << 0)
+#define AT91_MC_SMC_WSEN BIT(7)
+#define AT91_MC_SMC_TDF GENMASK(11, 8)
+#define AT91_MC_SMC_TDF_(x) ((x) << 8)
+#define AT91_MC_SMC_TDF_MAX 0xf
+#define AT91_MC_SMC_BAT BIT(12)
+#define AT91_MC_SMC_DBW GENMASK(14, 13)
+#define AT91_MC_SMC_DBW_16 (1 << 13)
+#define AT91_MC_SMC_DBW_8 (2 << 13)
+#define AT91_MC_SMC_DPR BIT(15)
+#define AT91_MC_SMC_ACSS GENMASK(17, 16)
+#define AT91_MC_SMC_ACSS_(x) ((x) << 16)
+#define AT91_MC_SMC_ACSS_MAX 3
+#define AT91_MC_SMC_RWSETUP GENMASK(26, 24)
+#define AT91_MC_SMC_RWSETUP_(x) ((x) << 24)
+#define AT91_MC_SMC_RWHOLD GENMASK(30, 28)
+#define AT91_MC_SMC_RWHOLD_(x) ((x) << 28)
+#define AT91_MC_SMC_RWHOLDSETUP_MAX 7
+
+/* SDRAM Controller registers */
+#define AT91_MC_SDRAMC_MR 0x90
+#define AT91_MC_SDRAMC_MODE GENMASK(3, 0)
+#define AT91_MC_SDRAMC_MODE_NORMAL (0 << 0)
+#define AT91_MC_SDRAMC_MODE_NOP (1 << 0)
+#define AT91_MC_SDRAMC_MODE_PRECHARGE (2 << 0)
+#define AT91_MC_SDRAMC_MODE_LMR (3 << 0)
+#define AT91_MC_SDRAMC_MODE_REFRESH (4 << 0)
+#define AT91_MC_SDRAMC_DBW_16 BIT(4)
+
+#define AT91_MC_SDRAMC_TR 0x94
+#define AT91_MC_SDRAMC_COUNT GENMASK(11, 0)
+
+#define AT91_MC_SDRAMC_CR 0x98
+#define AT91_MC_SDRAMC_NC GENMASK(1, 0)
+#define AT91_MC_SDRAMC_NC_8 (0 << 0)
+#define AT91_MC_SDRAMC_NC_9 (1 << 0)
+#define AT91_MC_SDRAMC_NC_10 (2 << 0)
+#define AT91_MC_SDRAMC_NC_11 (3 << 0)
+#define AT91_MC_SDRAMC_NR GENMASK(3, 2)
+#define AT91_MC_SDRAMC_NR_11 (0 << 2)
+#define AT91_MC_SDRAMC_NR_12 (1 << 2)
+#define AT91_MC_SDRAMC_NR_13 (2 << 2)
+#define AT91_MC_SDRAMC_NB BIT(4)
+#define AT91_MC_SDRAMC_NB_2 (0 << 4)
+#define AT91_MC_SDRAMC_NB_4 (1 << 4)
+#define AT91_MC_SDRAMC_CAS GENMASK(6, 5)
+#define AT91_MC_SDRAMC_CAS_2 (2 << 5)
+#define AT91_MC_SDRAMC_TWR GENMASK(10, 7)
+#define AT91_MC_SDRAMC_TRC GENMASK(14, 11)
+#define AT91_MC_SDRAMC_TRP GENMASK(18, 15)
+#define AT91_MC_SDRAMC_TRCD GENMASK(22, 19)
+#define AT91_MC_SDRAMC_TRAS GENMASK(26, 23)
+#define AT91_MC_SDRAMC_TXSR GENMASK(30, 27)
+
+#define AT91_MC_SDRAMC_SRR 0x9c
+#define AT91_MC_SDRAMC_SRCB BIT(0)
+
+#define AT91_MC_SDRAMC_LPR 0xa0
+#define AT91_MC_SDRAMC_LPCB BIT(0)
+
+#define AT91_MC_SDRAMC_IER 0xa4
+#define AT91_MC_SDRAMC_IDR 0xa8
+#define AT91_MC_SDRAMC_IMR 0xac
+#define AT91_MC_SDRAMC_ISR 0xb0
+#define AT91_MC_SDRAMC_RES BIT(0)
+
+/* Burst Flash Controller register */
+#define AT91_MC_BFC_MR 0xc0
+#define AT91_MC_BFC_BFCOM GENMASK(1, 0)
+#define AT91_MC_BFC_BFCOM_DISABLED (0 << 0)
+#define AT91_MC_BFC_BFCOM_ASYNC (1 << 0)
+#define AT91_MC_BFC_BFCOM_BURST (2 << 0)
+#define AT91_MC_BFC_BFCC GENMASK(3, 2)
+#define AT91_MC_BFC_BFCC_MCK (1 << 2)
+#define AT91_MC_BFC_BFCC_DIV2 (2 << 2)
+#define AT91_MC_BFC_BFCC_DIV4 (3 << 2)
+#define AT91_MC_BFC_AVL GENMASK(7, 4)
+#define AT91_MC_BFC_PAGES GENMASK(10, 8)
+#define AT91_MC_BFC_PAGES_NO_PAGE (0 << 8)
+#define AT91_MC_BFC_PAGES_16 (1 << 8)
+#define AT91_MC_BFC_PAGES_32 (2 << 8)
+#define AT91_MC_BFC_PAGES_64 (3 << 8)
+#define AT91_MC_BFC_PAGES_128 (4 << 8)
+#define AT91_MC_BFC_PAGES_256 (5 << 8)
+#define AT91_MC_BFC_PAGES_512 (6 << 8)
+#define AT91_MC_BFC_PAGES_1024 (7 << 8)
+#define AT91_MC_BFC_OEL GENMASK(13, 12)
+#define AT91_MC_BFC_BAAEN BIT(16)
+#define AT91_MC_BFC_BFOEH BIT(17)
+#define AT91_MC_BFC_MUXEN BIT(18)
+#define AT91_MC_BFC_RDYEN BIT(19)
+
+#endif /* _LINUX_MFD_SYSCON_ATMEL_MC_H_ */
diff --git a/include/soc/at91/at91rm9200_sdramc.h b/include/soc/at91/at91rm9200_sdramc.h
deleted file mode 100644
index aa047f45..0000000
--- a/include/soc/at91/at91rm9200_sdramc.h
+++ /dev/null
@@ -1,63 +0,0 @@
-/*
- * arch/arm/mach-at91/include/mach/at91rm9200_sdramc.h
- *
- * Copyright (C) 2005 Ivan Kokshaysky
- * Copyright (C) SAN People
- *
- * Memory Controllers (SDRAMC only) - System peripherals registers.
- * Based on AT91RM9200 datasheet revision E.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- */
-
-#ifndef AT91RM9200_SDRAMC_H
-#define AT91RM9200_SDRAMC_H
-
-/* SDRAM Controller registers */
-#define AT91RM9200_SDRAMC_MR 0x90 /* Mode Register */
-#define AT91RM9200_SDRAMC_MODE (0xf << 0) /* Command Mode */
-#define AT91RM9200_SDRAMC_MODE_NORMAL (0 << 0)
-#define AT91RM9200_SDRAMC_MODE_NOP (1 << 0)
-#define AT91RM9200_SDRAMC_MODE_PRECHARGE (2 << 0)
-#define AT91RM9200_SDRAMC_MODE_LMR (3 << 0)
-#define AT91RM9200_SDRAMC_MODE_REFRESH (4 << 0)
-#define AT91RM9200_SDRAMC_DBW (1 << 4) /* Data Bus Width */
-#define AT91RM9200_SDRAMC_DBW_32 (0 << 4)
-#define AT91RM9200_SDRAMC_DBW_16 (1 << 4)
-
-#define AT91RM9200_SDRAMC_TR 0x94 /* Refresh Timer Register */
-#define AT91RM9200_SDRAMC_COUNT (0xfff << 0) /* Refresh Timer Count */
-
-#define AT91RM9200_SDRAMC_CR 0x98 /* Configuration Register */
-#define AT91RM9200_SDRAMC_NC (3 << 0) /* Number of Column Bits */
-#define AT91RM9200_SDRAMC_NC_8 (0 << 0)
-#define AT91RM9200_SDRAMC_NC_9 (1 << 0)
-#define AT91RM9200_SDRAMC_NC_10 (2 << 0)
-#define AT91RM9200_SDRAMC_NC_11 (3 << 0)
-#define AT91RM9200_SDRAMC_NR (3 << 2) /* Number of Row Bits */
-#define AT91RM9200_SDRAMC_NR_11 (0 << 2)
-#define AT91RM9200_SDRAMC_NR_12 (1 << 2)
-#define AT91RM9200_SDRAMC_NR_13 (2 << 2)
-#define AT91RM9200_SDRAMC_NB (1 << 4) /* Number of Banks */
-#define AT91RM9200_SDRAMC_NB_2 (0 << 4)
-#define AT91RM9200_SDRAMC_NB_4 (1 << 4)
-#define AT91RM9200_SDRAMC_CAS (3 << 5) /* CAS Latency */
-#define AT91RM9200_SDRAMC_CAS_2 (2 << 5)
-#define AT91RM9200_SDRAMC_TWR (0xf << 7) /* Write Recovery Delay */
-#define AT91RM9200_SDRAMC_TRC (0xf << 11) /* Row Cycle Delay */
-#define AT91RM9200_SDRAMC_TRP (0xf << 15) /* Row Precharge Delay */
-#define AT91RM9200_SDRAMC_TRCD (0xf << 19) /* Row to Column Delay */
-#define AT91RM9200_SDRAMC_TRAS (0xf << 23) /* Active to Precharge Delay */
-#define AT91RM9200_SDRAMC_TXSR (0xf << 27) /* Exit Self Refresh to Active Delay */
-
-#define AT91RM9200_SDRAMC_SRR 0x9c /* Self Refresh Register */
-#define AT91RM9200_SDRAMC_LPR 0xa0 /* Low Power Register */
-#define AT91RM9200_SDRAMC_IER 0xa4 /* Interrupt Enable Register */
-#define AT91RM9200_SDRAMC_IDR 0xa8 /* Interrupt Disable Register */
-#define AT91RM9200_SDRAMC_IMR 0xac /* Interrupt Mask Register */
-#define AT91RM9200_SDRAMC_ISR 0xb0 /* Interrupt Status Register */
-
-#endif