ACPI: PCI: fix GSI/IRQ naming confusion
The interrupt numbers from _PRT entries are GSIs, not Linux IRQs.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
diff --git a/drivers/acpi/pci_irq.c b/drivers/acpi/pci_irq.c
index c6a03647..9302f4b 100644
--- a/drivers/acpi/pci_irq.c
+++ b/drivers/acpi/pci_irq.c
@@ -333,7 +333,7 @@
*polarity = ACPI_ACTIVE_LOW;
}
- ACPI_DEBUG_PRINT((ACPI_DB_INFO, "Found IRQ %d\n", irq));
+ ACPI_DEBUG_PRINT((ACPI_DB_INFO, "Found GSI %d\n", irq));
return irq;
}
@@ -432,7 +432,7 @@
return -1;
}
- ACPI_DEBUG_PRINT((ACPI_DB_INFO, "Derive IRQ %d for device %s from %s\n",
+ ACPI_DEBUG_PRINT((ACPI_DB_INFO, "Derive GSI %d for device %s from %s\n",
irq, pci_name(dev), pci_name(bridge)));
return irq;
@@ -446,7 +446,7 @@
int acpi_pci_irq_enable(struct pci_dev *dev)
{
- int irq = 0;
+ int gsi = 0;
u8 pin = 0;
int triggering = ACPI_LEVEL_SENSITIVE;
int polarity = ACPI_ACTIVE_LOW;
@@ -468,7 +468,7 @@
* First we check the PCI IRQ routing table (PRT) for an IRQ. PRT
* values override any BIOS-assigned IRQs set during boot.
*/
- irq = acpi_pci_irq_lookup(dev->bus, PCI_SLOT(dev->devfn), pin,
+ gsi = acpi_pci_irq_lookup(dev->bus, PCI_SLOT(dev->devfn), pin,
&triggering, &polarity, &link,
acpi_pci_allocate_irq);
@@ -476,12 +476,12 @@
* If no PRT entry was found, we'll try to derive an IRQ from the
* device's parent bridge.
*/
- if (irq < 0)
- irq = acpi_pci_irq_derive(dev, pin, &triggering,
+ if (gsi < 0)
+ gsi = acpi_pci_irq_derive(dev, pin, &triggering,
&polarity, &link,
acpi_pci_allocate_irq);
- if (irq < 0) {
+ if (gsi < 0) {
/*
* IDE legacy mode controller IRQs are magic. Why do compat
* extensions always make such a nasty mess.
@@ -494,7 +494,7 @@
* No IRQ known to the ACPI subsystem - maybe the BIOS /
* driver reported one, then use it. Exit in any case.
*/
- if (irq < 0) {
+ if (gsi < 0) {
dev_warn(&dev->dev, "PCI INT %c: no GSI", 'A' + pin);
/* Interrupt Line values above 0xF are forbidden */
if (dev->irq > 0 && (dev->irq <= 0xF)) {
@@ -508,7 +508,7 @@
}
}
- rc = acpi_register_gsi(irq, triggering, polarity);
+ rc = acpi_register_gsi(gsi, triggering, polarity);
if (rc < 0) {
dev_warn(&dev->dev, "PCI INT %c: failed to register GSI\n",
'A' + pin);
@@ -522,7 +522,7 @@
link_desc[0] = '\0';
dev_info(&dev->dev, "PCI INT %c%s -> GSI %u (%s, %s) -> IRQ %d\n",
- 'A' + pin, link_desc, irq,
+ 'A' + pin, link_desc, gsi,
(triggering == ACPI_LEVEL_SENSITIVE) ? "level" : "edge",
(polarity == ACPI_ACTIVE_LOW) ? "low" : "high", dev->irq);