| /* |
| * PCIe driver for Marvell Armada 370 and Armada XP SoCs |
| * |
| * This file is licensed under the terms of the GNU General Public |
| * License version 2. This program is licensed "as is" without any |
| * warranty of any kind, whether express or implied. |
| */ |
| |
| #include <linux/kernel.h> |
| #include <linux/pci.h> |
| #include <linux/clk.h> |
| #include <linux/delay.h> |
| #include <linux/gpio.h> |
| #include <linux/module.h> |
| #include <linux/mbus.h> |
| #include <linux/msi.h> |
| #include <linux/slab.h> |
| #include <linux/platform_device.h> |
| #include <linux/of_address.h> |
| #include <linux/of_irq.h> |
| #include <linux/of_gpio.h> |
| #include <linux/of_pci.h> |
| #include <linux/of_platform.h> |
| |
| /* |
| * PCIe unit register offsets. |
| */ |
| #define PCIE_DEV_ID_OFF 0x0000 |
| #define PCIE_CMD_OFF 0x0004 |
| #define PCIE_DEV_REV_OFF 0x0008 |
| #define PCIE_BAR_LO_OFF(n) (0x0010 + ((n) << 3)) |
| #define PCIE_BAR_HI_OFF(n) (0x0014 + ((n) << 3)) |
| #define PCIE_HEADER_LOG_4_OFF 0x0128 |
| #define PCIE_BAR_CTRL_OFF(n) (0x1804 + (((n) - 1) * 4)) |
| #define PCIE_WIN04_CTRL_OFF(n) (0x1820 + ((n) << 4)) |
| #define PCIE_WIN04_BASE_OFF(n) (0x1824 + ((n) << 4)) |
| #define PCIE_WIN04_REMAP_OFF(n) (0x182c + ((n) << 4)) |
| #define PCIE_WIN5_CTRL_OFF 0x1880 |
| #define PCIE_WIN5_BASE_OFF 0x1884 |
| #define PCIE_WIN5_REMAP_OFF 0x188c |
| #define PCIE_CONF_ADDR_OFF 0x18f8 |
| #define PCIE_CONF_ADDR_EN 0x80000000 |
| #define PCIE_CONF_REG(r) ((((r) & 0xf00) << 16) | ((r) & 0xfc)) |
| #define PCIE_CONF_BUS(b) (((b) & 0xff) << 16) |
| #define PCIE_CONF_DEV(d) (((d) & 0x1f) << 11) |
| #define PCIE_CONF_FUNC(f) (((f) & 0x7) << 8) |
| #define PCIE_CONF_ADDR(bus, devfn, where) \ |
| (PCIE_CONF_BUS(bus) | PCIE_CONF_DEV(PCI_SLOT(devfn)) | \ |
| PCIE_CONF_FUNC(PCI_FUNC(devfn)) | PCIE_CONF_REG(where) | \ |
| PCIE_CONF_ADDR_EN) |
| #define PCIE_CONF_DATA_OFF 0x18fc |
| #define PCIE_MASK_OFF 0x1910 |
| #define PCIE_MASK_ENABLE_INTS 0x0f000000 |
| #define PCIE_CTRL_OFF 0x1a00 |
| #define PCIE_CTRL_X1_MODE 0x0001 |
| #define PCIE_STAT_OFF 0x1a04 |
| #define PCIE_STAT_BUS 0xff00 |
| #define PCIE_STAT_DEV 0x1f0000 |
| #define PCIE_STAT_LINK_DOWN BIT(0) |
| #define PCIE_DEBUG_CTRL 0x1a60 |
| #define PCIE_DEBUG_SOFT_RESET BIT(20) |
| |
| /* PCI configuration space of a PCI-to-PCI bridge */ |
| struct mvebu_sw_pci_bridge { |
| u16 vendor; |
| u16 device; |
| u16 command; |
| u16 class; |
| u8 interface; |
| u8 revision; |
| u8 bist; |
| u8 header_type; |
| u8 latency_timer; |
| u8 cache_line_size; |
| u32 bar[2]; |
| u8 primary_bus; |
| u8 secondary_bus; |
| u8 subordinate_bus; |
| u8 secondary_latency_timer; |
| u8 iobase; |
| u8 iolimit; |
| u16 secondary_status; |
| u16 membase; |
| u16 memlimit; |
| u16 iobaseupper; |
| u16 iolimitupper; |
| u8 cappointer; |
| u8 reserved1; |
| u16 reserved2; |
| u32 romaddr; |
| u8 intline; |
| u8 intpin; |
| u16 bridgectrl; |
| }; |
| |
| struct mvebu_pcie_port; |
| |
| /* Structure representing all PCIe interfaces */ |
| struct mvebu_pcie { |
| struct platform_device *pdev; |
| struct mvebu_pcie_port *ports; |
| struct msi_controller *msi; |
| struct resource io; |
| char io_name[30]; |
| struct resource realio; |
| char mem_name[30]; |
| struct resource mem; |
| struct resource busn; |
| int nports; |
| }; |
| |
| /* Structure representing one PCIe interface */ |
| struct mvebu_pcie_port { |
| char *name; |
| void __iomem *base; |
| u32 port; |
| u32 lane; |
| int devfn; |
| unsigned int mem_target; |
| unsigned int mem_attr; |
| unsigned int io_target; |
| unsigned int io_attr; |
| struct clk *clk; |
| int reset_gpio; |
| int reset_active_low; |
| char *reset_name; |
| struct mvebu_sw_pci_bridge bridge; |
| struct device_node *dn; |
| struct mvebu_pcie *pcie; |
| phys_addr_t memwin_base; |
| size_t memwin_size; |
| phys_addr_t iowin_base; |
| size_t iowin_size; |
| }; |
| |
| static inline void mvebu_writel(struct mvebu_pcie_port *port, u32 val, u32 reg) |
| { |
| writel(val, port->base + reg); |
| } |
| |
| static inline u32 mvebu_readl(struct mvebu_pcie_port *port, u32 reg) |
| { |
| return readl(port->base + reg); |
| } |
| |
| static inline bool mvebu_has_ioport(struct mvebu_pcie_port *port) |
| { |
| return port->io_target != -1 && port->io_attr != -1; |
| } |
| |
| static bool mvebu_pcie_link_up(struct mvebu_pcie_port *port) |
| { |
| return !(mvebu_readl(port, PCIE_STAT_OFF) & PCIE_STAT_LINK_DOWN); |
| } |
| |
| static void mvebu_pcie_set_local_bus_nr(struct mvebu_pcie_port *port, int nr) |
| { |
| u32 stat; |
| |
| stat = mvebu_readl(port, PCIE_STAT_OFF); |
| stat &= ~PCIE_STAT_BUS; |
| stat |= nr << 8; |
| mvebu_writel(port, stat, PCIE_STAT_OFF); |
| } |
| |
| static void mvebu_pcie_set_local_dev_nr(struct mvebu_pcie_port *port, int nr) |
| { |
| u32 stat; |
| |
| stat = mvebu_readl(port, PCIE_STAT_OFF); |
| stat &= ~PCIE_STAT_DEV; |
| stat |= nr << 16; |
| mvebu_writel(port, stat, PCIE_STAT_OFF); |
| } |
| |
| /* |
| * Setup PCIE BARs and Address Decode Wins: |
| * BAR[0,2] -> disabled, BAR[1] -> covers all DRAM banks |
| * WIN[0-3] -> DRAM bank[0-3] |
| */ |
| static void mvebu_pcie_setup_wins(struct mvebu_pcie_port *port) |
| { |
| const struct mbus_dram_target_info *dram; |
| u32 size; |
| int i; |
| |
| dram = mv_mbus_dram_info(); |
| |
| /* First, disable and clear BARs and windows. */ |
| for (i = 1; i < 3; i++) { |
| mvebu_writel(port, 0, PCIE_BAR_CTRL_OFF(i)); |
| mvebu_writel(port, 0, PCIE_BAR_LO_OFF(i)); |
| mvebu_writel(port, 0, PCIE_BAR_HI_OFF(i)); |
| } |
| |
| for (i = 0; i < 5; i++) { |
| mvebu_writel(port, 0, PCIE_WIN04_CTRL_OFF(i)); |
| mvebu_writel(port, 0, PCIE_WIN04_BASE_OFF(i)); |
| mvebu_writel(port, 0, PCIE_WIN04_REMAP_OFF(i)); |
| } |
| |
| mvebu_writel(port, 0, PCIE_WIN5_CTRL_OFF); |
| mvebu_writel(port, 0, PCIE_WIN5_BASE_OFF); |
| mvebu_writel(port, 0, PCIE_WIN5_REMAP_OFF); |
| |
| /* Setup windows for DDR banks. Count total DDR size on the fly. */ |
| size = 0; |
| for (i = 0; i < dram->num_cs; i++) { |
| const struct mbus_dram_window *cs = dram->cs + i; |
| |
| mvebu_writel(port, cs->base & 0xffff0000, |
| PCIE_WIN04_BASE_OFF(i)); |
| mvebu_writel(port, 0, PCIE_WIN04_REMAP_OFF(i)); |
| mvebu_writel(port, |
| ((cs->size - 1) & 0xffff0000) | |
| (cs->mbus_attr << 8) | |
| (dram->mbus_dram_target_id << 4) | 1, |
| PCIE_WIN04_CTRL_OFF(i)); |
| |
| size += cs->size; |
| } |
| |
| /* Round up 'size' to the nearest power of two. */ |
| if ((size & (size - 1)) != 0) |
| size = 1 << fls(size); |
| |
| /* Setup BAR[1] to all DRAM banks. */ |
| mvebu_writel(port, dram->cs[0].base, PCIE_BAR_LO_OFF(1)); |
| mvebu_writel(port, 0, PCIE_BAR_HI_OFF(1)); |
| mvebu_writel(port, ((size - 1) & 0xffff0000) | 1, |
| PCIE_BAR_CTRL_OFF(1)); |
| } |
| |
| static void mvebu_pcie_setup_hw(struct mvebu_pcie_port *port) |
| { |
| u32 cmd, mask; |
| |
| /* Point PCIe unit MBUS decode windows to DRAM space. */ |
| mvebu_pcie_setup_wins(port); |
| |
| /* Master + slave enable. */ |
| cmd = mvebu_readl(port, PCIE_CMD_OFF); |
| cmd |= PCI_COMMAND_IO; |
| cmd |= PCI_COMMAND_MEMORY; |
| cmd |= PCI_COMMAND_MASTER; |
| mvebu_writel(port, cmd, PCIE_CMD_OFF); |
| |
| /* Enable interrupt lines A-D. */ |
| mask = mvebu_readl(port, PCIE_MASK_OFF); |
| mask |= PCIE_MASK_ENABLE_INTS; |
| mvebu_writel(port, mask, PCIE_MASK_OFF); |
| } |
| |
| static int mvebu_pcie_hw_rd_conf(struct mvebu_pcie_port *port, |
| struct pci_bus *bus, |
| u32 devfn, int where, int size, u32 *val) |
| { |
| mvebu_writel(port, PCIE_CONF_ADDR(bus->number, devfn, where), |
| PCIE_CONF_ADDR_OFF); |
| |
| *val = mvebu_readl(port, PCIE_CONF_DATA_OFF); |
| |
| if (size == 1) |
| *val = (*val >> (8 * (where & 3))) & 0xff; |
| else if (size == 2) |
| *val = (*val >> (8 * (where & 3))) & 0xffff; |
| |
| return PCIBIOS_SUCCESSFUL; |
| } |
| |
| static int mvebu_pcie_hw_wr_conf(struct mvebu_pcie_port *port, |
| struct pci_bus *bus, |
| u32 devfn, int where, int size, u32 val) |
| { |
| u32 _val, shift = 8 * (where & 3); |
| |
| mvebu_writel(port, PCIE_CONF_ADDR(bus->number, devfn, where), |
| PCIE_CONF_ADDR_OFF); |
| _val = mvebu_readl(port, PCIE_CONF_DATA_OFF); |
| |
| if (size == 4) |
| _val = val; |
| else if (size == 2) |
| _val = (_val & ~(0xffff << shift)) | ((val & 0xffff) << shift); |
| else if (size == 1) |
| _val = (_val & ~(0xff << shift)) | ((val & 0xff) << shift); |
| else |
| return PCIBIOS_BAD_REGISTER_NUMBER; |
| |
| mvebu_writel(port, _val, PCIE_CONF_DATA_OFF); |
| |
| return PCIBIOS_SUCCESSFUL; |
| } |
| |
| /* |
| * Remove windows, starting from the largest ones to the smallest |
| * ones. |
| */ |
| static void mvebu_pcie_del_windows(struct mvebu_pcie_port *port, |
| phys_addr_t base, size_t size) |
| { |
| while (size) { |
| size_t sz = 1 << (fls(size) - 1); |
| |
| mvebu_mbus_del_window(base, sz); |
| base += sz; |
| size -= sz; |
| } |
| } |
| |
| /* |
| * MBus windows can only have a power of two size, but PCI BARs do not |
| * have this constraint. Therefore, we have to split the PCI BAR into |
| * areas each having a power of two size. We start from the largest |
| * one (i.e highest order bit set in the size). |
| */ |
| static void mvebu_pcie_add_windows(struct mvebu_pcie_port *port, |
| unsigned int target, unsigned int attribute, |
| phys_addr_t base, size_t size, |
| phys_addr_t remap) |
| { |
| size_t size_mapped = 0; |
| |
| while (size) { |
| size_t sz = 1 << (fls(size) - 1); |
| int ret; |
| |
| ret = mvebu_mbus_add_window_remap_by_id(target, attribute, base, |
| sz, remap); |
| if (ret) { |
| phys_addr_t end = base + sz - 1; |
| |
| dev_err(&port->pcie->pdev->dev, |
| "Could not create MBus window at [mem %pa-%pa]: %d\n", |
| &base, &end, ret); |
| mvebu_pcie_del_windows(port, base - size_mapped, |
| size_mapped); |
| return; |
| } |
| |
| size -= sz; |
| size_mapped += sz; |
| base += sz; |
| if (remap != MVEBU_MBUS_NO_REMAP) |
| remap += sz; |
| } |
| } |
| |
| static void mvebu_pcie_handle_iobase_change(struct mvebu_pcie_port *port) |
| { |
| phys_addr_t iobase; |
| |
| /* Are the new iobase/iolimit values invalid? */ |
| if (port->bridge.iolimit < port->bridge.iobase || |
| port->bridge.iolimitupper < port->bridge.iobaseupper || |
| !(port->bridge.command & PCI_COMMAND_IO)) { |
| |
| /* If a window was configured, remove it */ |
| if (port->iowin_base) { |
| mvebu_pcie_del_windows(port, port->iowin_base, |
| port->iowin_size); |
| port->iowin_base = 0; |
| port->iowin_size = 0; |
| } |
| |
| return; |
| } |
| |
| if (!mvebu_has_ioport(port)) { |
| dev_WARN(&port->pcie->pdev->dev, |
| "Attempt to set IO when IO is disabled\n"); |
| return; |
| } |
| |
| /* |
| * We read the PCI-to-PCI bridge emulated registers, and |
| * calculate the base address and size of the address decoding |
| * window to setup, according to the PCI-to-PCI bridge |
| * specifications. iobase is the bus address, port->iowin_base |
| * is the CPU address. |
| */ |
| iobase = ((port->bridge.iobase & 0xF0) << 8) | |
| (port->bridge.iobaseupper << 16); |
| port->iowin_base = port->pcie->io.start + iobase; |
| port->iowin_size = ((0xFFF | ((port->bridge.iolimit & 0xF0) << 8) | |
| (port->bridge.iolimitupper << 16)) - |
| iobase) + 1; |
| |
| mvebu_pcie_add_windows(port, port->io_target, port->io_attr, |
| port->iowin_base, port->iowin_size, |
| iobase); |
| } |
| |
| static void mvebu_pcie_handle_membase_change(struct mvebu_pcie_port *port) |
| { |
| /* Are the new membase/memlimit values invalid? */ |
| if (port->bridge.memlimit < port->bridge.membase || |
| !(port->bridge.command & PCI_COMMAND_MEMORY)) { |
| |
| /* If a window was configured, remove it */ |
| if (port->memwin_base) { |
| mvebu_pcie_del_windows(port, port->memwin_base, |
| port->memwin_size); |
| port->memwin_base = 0; |
| port->memwin_size = 0; |
| } |
| |
| return; |
| } |
| |
| /* |
| * We read the PCI-to-PCI bridge emulated registers, and |
| * calculate the base address and size of the address decoding |
| * window to setup, according to the PCI-to-PCI bridge |
| * specifications. |
| */ |
| port->memwin_base = ((port->bridge.membase & 0xFFF0) << 16); |
| port->memwin_size = |
| (((port->bridge.memlimit & 0xFFF0) << 16) | 0xFFFFF) - |
| port->memwin_base + 1; |
| |
| mvebu_pcie_add_windows(port, port->mem_target, port->mem_attr, |
| port->memwin_base, port->memwin_size, |
| MVEBU_MBUS_NO_REMAP); |
| } |
| |
| /* |
| * Initialize the configuration space of the PCI-to-PCI bridge |
| * associated with the given PCIe interface. |
| */ |
| static void mvebu_sw_pci_bridge_init(struct mvebu_pcie_port *port) |
| { |
| struct mvebu_sw_pci_bridge *bridge = &port->bridge; |
| |
| memset(bridge, 0, sizeof(struct mvebu_sw_pci_bridge)); |
| |
| bridge->class = PCI_CLASS_BRIDGE_PCI; |
| bridge->vendor = PCI_VENDOR_ID_MARVELL; |
| bridge->device = mvebu_readl(port, PCIE_DEV_ID_OFF) >> 16; |
| bridge->revision = mvebu_readl(port, PCIE_DEV_REV_OFF) & 0xff; |
| bridge->header_type = PCI_HEADER_TYPE_BRIDGE; |
| bridge->cache_line_size = 0x10; |
| |
| /* We support 32 bits I/O addressing */ |
| bridge->iobase = PCI_IO_RANGE_TYPE_32; |
| bridge->iolimit = PCI_IO_RANGE_TYPE_32; |
| } |
| |
| /* |
| * Read the configuration space of the PCI-to-PCI bridge associated to |
| * the given PCIe interface. |
| */ |
| static int mvebu_sw_pci_bridge_read(struct mvebu_pcie_port *port, |
| unsigned int where, int size, u32 *value) |
| { |
| struct mvebu_sw_pci_bridge *bridge = &port->bridge; |
| |
| switch (where & ~3) { |
| case PCI_VENDOR_ID: |
| *value = bridge->device << 16 | bridge->vendor; |
| break; |
| |
| case PCI_COMMAND: |
| *value = bridge->command; |
| break; |
| |
| case PCI_CLASS_REVISION: |
| *value = bridge->class << 16 | bridge->interface << 8 | |
| bridge->revision; |
| break; |
| |
| case PCI_CACHE_LINE_SIZE: |
| *value = bridge->bist << 24 | bridge->header_type << 16 | |
| bridge->latency_timer << 8 | bridge->cache_line_size; |
| break; |
| |
| case PCI_BASE_ADDRESS_0 ... PCI_BASE_ADDRESS_1: |
| *value = bridge->bar[((where & ~3) - PCI_BASE_ADDRESS_0) / 4]; |
| break; |
| |
| case PCI_PRIMARY_BUS: |
| *value = (bridge->secondary_latency_timer << 24 | |
| bridge->subordinate_bus << 16 | |
| bridge->secondary_bus << 8 | |
| bridge->primary_bus); |
| break; |
| |
| case PCI_IO_BASE: |
| if (!mvebu_has_ioport(port)) |
| *value = bridge->secondary_status << 16; |
| else |
| *value = (bridge->secondary_status << 16 | |
| bridge->iolimit << 8 | |
| bridge->iobase); |
| break; |
| |
| case PCI_MEMORY_BASE: |
| *value = (bridge->memlimit << 16 | bridge->membase); |
| break; |
| |
| case PCI_PREF_MEMORY_BASE: |
| *value = 0; |
| break; |
| |
| case PCI_IO_BASE_UPPER16: |
| *value = (bridge->iolimitupper << 16 | bridge->iobaseupper); |
| break; |
| |
| case PCI_ROM_ADDRESS1: |
| *value = 0; |
| break; |
| |
| case PCI_INTERRUPT_LINE: |
| /* LINE PIN MIN_GNT MAX_LAT */ |
| *value = 0; |
| break; |
| |
| default: |
| *value = 0xffffffff; |
| return PCIBIOS_BAD_REGISTER_NUMBER; |
| } |
| |
| if (size == 2) |
| *value = (*value >> (8 * (where & 3))) & 0xffff; |
| else if (size == 1) |
| *value = (*value >> (8 * (where & 3))) & 0xff; |
| |
| return PCIBIOS_SUCCESSFUL; |
| } |
| |
| /* Write to the PCI-to-PCI bridge configuration space */ |
| static int mvebu_sw_pci_bridge_write(struct mvebu_pcie_port *port, |
| unsigned int where, int size, u32 value) |
| { |
| struct mvebu_sw_pci_bridge *bridge = &port->bridge; |
| u32 mask, reg; |
| int err; |
| |
| if (size == 4) |
| mask = 0x0; |
| else if (size == 2) |
| mask = ~(0xffff << ((where & 3) * 8)); |
| else if (size == 1) |
| mask = ~(0xff << ((where & 3) * 8)); |
| else |
| return PCIBIOS_BAD_REGISTER_NUMBER; |
| |
| err = mvebu_sw_pci_bridge_read(port, where & ~3, 4, ®); |
| if (err) |
| return err; |
| |
| value = (reg & mask) | value << ((where & 3) * 8); |
| |
| switch (where & ~3) { |
| case PCI_COMMAND: |
| { |
| u32 old = bridge->command; |
| |
| if (!mvebu_has_ioport(port)) |
| value &= ~PCI_COMMAND_IO; |
| |
| bridge->command = value & 0xffff; |
| if ((old ^ bridge->command) & PCI_COMMAND_IO) |
| mvebu_pcie_handle_iobase_change(port); |
| if ((old ^ bridge->command) & PCI_COMMAND_MEMORY) |
| mvebu_pcie_handle_membase_change(port); |
| break; |
| } |
| |
| case PCI_BASE_ADDRESS_0 ... PCI_BASE_ADDRESS_1: |
| bridge->bar[((where & ~3) - PCI_BASE_ADDRESS_0) / 4] = value; |
| break; |
| |
| case PCI_IO_BASE: |
| /* |
| * We also keep bit 1 set, it is a read-only bit that |
| * indicates we support 32 bits addressing for the |
| * I/O |
| */ |
| bridge->iobase = (value & 0xff) | PCI_IO_RANGE_TYPE_32; |
| bridge->iolimit = ((value >> 8) & 0xff) | PCI_IO_RANGE_TYPE_32; |
| mvebu_pcie_handle_iobase_change(port); |
| break; |
| |
| case PCI_MEMORY_BASE: |
| bridge->membase = value & 0xffff; |
| bridge->memlimit = value >> 16; |
| mvebu_pcie_handle_membase_change(port); |
| break; |
| |
| case PCI_IO_BASE_UPPER16: |
| bridge->iobaseupper = value & 0xffff; |
| bridge->iolimitupper = value >> 16; |
| mvebu_pcie_handle_iobase_change(port); |
| break; |
| |
| case PCI_PRIMARY_BUS: |
| bridge->primary_bus = value & 0xff; |
| bridge->secondary_bus = (value >> 8) & 0xff; |
| bridge->subordinate_bus = (value >> 16) & 0xff; |
| bridge->secondary_latency_timer = (value >> 24) & 0xff; |
| mvebu_pcie_set_local_bus_nr(port, bridge->secondary_bus); |
| break; |
| |
| default: |
| break; |
| } |
| |
| return PCIBIOS_SUCCESSFUL; |
| } |
| |
| static inline struct mvebu_pcie *sys_to_pcie(struct pci_sys_data *sys) |
| { |
| return sys->private_data; |
| } |
| |
| static struct mvebu_pcie_port *mvebu_pcie_find_port(struct mvebu_pcie *pcie, |
| struct pci_bus *bus, |
| int devfn) |
| { |
| int i; |
| |
| for (i = 0; i < pcie->nports; i++) { |
| struct mvebu_pcie_port *port = &pcie->ports[i]; |
| if (bus->number == 0 && port->devfn == devfn) |
| return port; |
| if (bus->number != 0 && |
| bus->number >= port->bridge.secondary_bus && |
| bus->number <= port->bridge.subordinate_bus) |
| return port; |
| } |
| |
| return NULL; |
| } |
| |
| /* PCI configuration space write function */ |
| static int mvebu_pcie_wr_conf(struct pci_bus *bus, u32 devfn, |
| int where, int size, u32 val) |
| { |
| struct mvebu_pcie *pcie = sys_to_pcie(bus->sysdata); |
| struct mvebu_pcie_port *port; |
| int ret; |
| |
| port = mvebu_pcie_find_port(pcie, bus, devfn); |
| if (!port) |
| return PCIBIOS_DEVICE_NOT_FOUND; |
| |
| /* Access the emulated PCI-to-PCI bridge */ |
| if (bus->number == 0) |
| return mvebu_sw_pci_bridge_write(port, where, size, val); |
| |
| if (!mvebu_pcie_link_up(port)) |
| return PCIBIOS_DEVICE_NOT_FOUND; |
| |
| /* |
| * On the secondary bus, we don't want to expose any other |
| * device than the device physically connected in the PCIe |
| * slot, visible in slot 0. In slot 1, there's a special |
| * Marvell device that only makes sense when the Armada is |
| * used as a PCIe endpoint. |
| */ |
| if (bus->number == port->bridge.secondary_bus && |
| PCI_SLOT(devfn) != 0) |
| return PCIBIOS_DEVICE_NOT_FOUND; |
| |
| /* Access the real PCIe interface */ |
| ret = mvebu_pcie_hw_wr_conf(port, bus, devfn, |
| where, size, val); |
| |
| return ret; |
| } |
| |
| /* PCI configuration space read function */ |
| static int mvebu_pcie_rd_conf(struct pci_bus *bus, u32 devfn, int where, |
| int size, u32 *val) |
| { |
| struct mvebu_pcie *pcie = sys_to_pcie(bus->sysdata); |
| struct mvebu_pcie_port *port; |
| int ret; |
| |
| port = mvebu_pcie_find_port(pcie, bus, devfn); |
| if (!port) { |
| *val = 0xffffffff; |
| return PCIBIOS_DEVICE_NOT_FOUND; |
| } |
| |
| /* Access the emulated PCI-to-PCI bridge */ |
| if (bus->number == 0) |
| return mvebu_sw_pci_bridge_read(port, where, size, val); |
| |
| if (!mvebu_pcie_link_up(port)) { |
| *val = 0xffffffff; |
| return PCIBIOS_DEVICE_NOT_FOUND; |
| } |
| |
| /* |
| * On the secondary bus, we don't want to expose any other |
| * device than the device physically connected in the PCIe |
| * slot, visible in slot 0. In slot 1, there's a special |
| * Marvell device that only makes sense when the Armada is |
| * used as a PCIe endpoint. |
| */ |
| if (bus->number == port->bridge.secondary_bus && |
| PCI_SLOT(devfn) != 0) { |
| *val = 0xffffffff; |
| return PCIBIOS_DEVICE_NOT_FOUND; |
| } |
| |
| /* Access the real PCIe interface */ |
| ret = mvebu_pcie_hw_rd_conf(port, bus, devfn, |
| where, size, val); |
| |
| return ret; |
| } |
| |
| static struct pci_ops mvebu_pcie_ops = { |
| .read = mvebu_pcie_rd_conf, |
| .write = mvebu_pcie_wr_conf, |
| }; |
| |
| static int mvebu_pcie_setup(int nr, struct pci_sys_data *sys) |
| { |
| struct mvebu_pcie *pcie = sys_to_pcie(sys); |
| int i; |
| int domain = 0; |
| |
| #ifdef CONFIG_PCI_DOMAINS |
| domain = sys->domain; |
| #endif |
| |
| snprintf(pcie->mem_name, sizeof(pcie->mem_name), "PCI MEM %04x", |
| domain); |
| pcie->mem.name = pcie->mem_name; |
| |
| snprintf(pcie->io_name, sizeof(pcie->io_name), "PCI I/O %04x", domain); |
| pcie->realio.name = pcie->io_name; |
| |
| if (request_resource(&iomem_resource, &pcie->mem)) |
| return 0; |
| |
| if (resource_size(&pcie->realio) != 0) { |
| if (request_resource(&ioport_resource, &pcie->realio)) { |
| release_resource(&pcie->mem); |
| return 0; |
| } |
| pci_add_resource_offset(&sys->resources, &pcie->realio, |
| sys->io_offset); |
| } |
| pci_add_resource_offset(&sys->resources, &pcie->mem, sys->mem_offset); |
| pci_add_resource(&sys->resources, &pcie->busn); |
| |
| for (i = 0; i < pcie->nports; i++) { |
| struct mvebu_pcie_port *port = &pcie->ports[i]; |
| if (!port->base) |
| continue; |
| mvebu_pcie_setup_hw(port); |
| } |
| |
| return 1; |
| } |
| |
| static struct pci_bus *mvebu_pcie_scan_bus(int nr, struct pci_sys_data *sys) |
| { |
| struct mvebu_pcie *pcie = sys_to_pcie(sys); |
| struct pci_bus *bus; |
| |
| bus = pci_create_root_bus(&pcie->pdev->dev, sys->busnr, |
| &mvebu_pcie_ops, sys, &sys->resources); |
| if (!bus) |
| return NULL; |
| |
| pci_scan_child_bus(bus); |
| |
| return bus; |
| } |
| |
| static void mvebu_pcie_add_bus(struct pci_bus *bus) |
| { |
| struct mvebu_pcie *pcie = sys_to_pcie(bus->sysdata); |
| bus->msi = pcie->msi; |
| } |
| |
| static resource_size_t mvebu_pcie_align_resource(struct pci_dev *dev, |
| const struct resource *res, |
| resource_size_t start, |
| resource_size_t size, |
| resource_size_t align) |
| { |
| if (dev->bus->number != 0) |
| return start; |
| |
| /* |
| * On the PCI-to-PCI bridge side, the I/O windows must have at |
| * least a 64 KB size and the memory windows must have at |
| * least a 1 MB size. Moreover, MBus windows need to have a |
| * base address aligned on their size, and their size must be |
| * a power of two. This means that if the BAR doesn't have a |
| * power of two size, several MBus windows will actually be |
| * created. We need to ensure that the biggest MBus window |
| * (which will be the first one) is aligned on its size, which |
| * explains the rounddown_pow_of_two() being done here. |
| */ |
| if (res->flags & IORESOURCE_IO) |
| return round_up(start, max_t(resource_size_t, SZ_64K, |
| rounddown_pow_of_two(size))); |
| else if (res->flags & IORESOURCE_MEM) |
| return round_up(start, max_t(resource_size_t, SZ_1M, |
| rounddown_pow_of_two(size))); |
| else |
| return start; |
| } |
| |
| static void mvebu_pcie_enable(struct mvebu_pcie *pcie) |
| { |
| struct hw_pci hw; |
| |
| memset(&hw, 0, sizeof(hw)); |
| |
| hw.nr_controllers = 1; |
| hw.private_data = (void **)&pcie; |
| hw.setup = mvebu_pcie_setup; |
| hw.scan = mvebu_pcie_scan_bus; |
| hw.map_irq = of_irq_parse_and_map_pci; |
| hw.ops = &mvebu_pcie_ops; |
| hw.align_resource = mvebu_pcie_align_resource; |
| hw.add_bus = mvebu_pcie_add_bus; |
| |
| pci_common_init(&hw); |
| } |
| |
| /* |
| * Looks up the list of register addresses encoded into the reg = |
| * <...> property for one that matches the given port/lane. Once |
| * found, maps it. |
| */ |
| static void __iomem *mvebu_pcie_map_registers(struct platform_device *pdev, |
| struct device_node *np, |
| struct mvebu_pcie_port *port) |
| { |
| struct resource regs; |
| int ret = 0; |
| |
| ret = of_address_to_resource(np, 0, ®s); |
| if (ret) |
| return ERR_PTR(ret); |
| |
| return devm_ioremap_resource(&pdev->dev, ®s); |
| } |
| |
| #define DT_FLAGS_TO_TYPE(flags) (((flags) >> 24) & 0x03) |
| #define DT_TYPE_IO 0x1 |
| #define DT_TYPE_MEM32 0x2 |
| #define DT_CPUADDR_TO_TARGET(cpuaddr) (((cpuaddr) >> 56) & 0xFF) |
| #define DT_CPUADDR_TO_ATTR(cpuaddr) (((cpuaddr) >> 48) & 0xFF) |
| |
| static int mvebu_get_tgt_attr(struct device_node *np, int devfn, |
| unsigned long type, |
| unsigned int *tgt, |
| unsigned int *attr) |
| { |
| const int na = 3, ns = 2; |
| const __be32 *range; |
| int rlen, nranges, rangesz, pna, i; |
| |
| *tgt = -1; |
| *attr = -1; |
| |
| range = of_get_property(np, "ranges", &rlen); |
| if (!range) |
| return -EINVAL; |
| |
| pna = of_n_addr_cells(np); |
| rangesz = pna + na + ns; |
| nranges = rlen / sizeof(__be32) / rangesz; |
| |
| for (i = 0; i < nranges; i++, range += rangesz) { |
| u32 flags = of_read_number(range, 1); |
| u32 slot = of_read_number(range + 1, 1); |
| u64 cpuaddr = of_read_number(range + na, pna); |
| unsigned long rtype; |
| |
| if (DT_FLAGS_TO_TYPE(flags) == DT_TYPE_IO) |
| rtype = IORESOURCE_IO; |
| else if (DT_FLAGS_TO_TYPE(flags) == DT_TYPE_MEM32) |
| rtype = IORESOURCE_MEM; |
| else |
| continue; |
| |
| if (slot == PCI_SLOT(devfn) && type == rtype) { |
| *tgt = DT_CPUADDR_TO_TARGET(cpuaddr); |
| *attr = DT_CPUADDR_TO_ATTR(cpuaddr); |
| return 0; |
| } |
| } |
| |
| return -ENOENT; |
| } |
| |
| static void mvebu_pcie_msi_enable(struct mvebu_pcie *pcie) |
| { |
| struct device_node *msi_node; |
| |
| msi_node = of_parse_phandle(pcie->pdev->dev.of_node, |
| "msi-parent", 0); |
| if (!msi_node) |
| return; |
| |
| pcie->msi = of_pci_find_msi_chip_by_node(msi_node); |
| |
| if (pcie->msi) |
| pcie->msi->dev = &pcie->pdev->dev; |
| } |
| |
| static int mvebu_pcie_probe(struct platform_device *pdev) |
| { |
| struct mvebu_pcie *pcie; |
| struct device_node *np = pdev->dev.of_node; |
| struct device_node *child; |
| int i, ret; |
| |
| pcie = devm_kzalloc(&pdev->dev, sizeof(struct mvebu_pcie), |
| GFP_KERNEL); |
| if (!pcie) |
| return -ENOMEM; |
| |
| pcie->pdev = pdev; |
| platform_set_drvdata(pdev, pcie); |
| |
| /* Get the PCIe memory and I/O aperture */ |
| mvebu_mbus_get_pcie_mem_aperture(&pcie->mem); |
| if (resource_size(&pcie->mem) == 0) { |
| dev_err(&pdev->dev, "invalid memory aperture size\n"); |
| return -EINVAL; |
| } |
| |
| mvebu_mbus_get_pcie_io_aperture(&pcie->io); |
| |
| if (resource_size(&pcie->io) != 0) { |
| pcie->realio.flags = pcie->io.flags; |
| pcie->realio.start = PCIBIOS_MIN_IO; |
| pcie->realio.end = min_t(resource_size_t, |
| IO_SPACE_LIMIT, |
| resource_size(&pcie->io)); |
| } else |
| pcie->realio = pcie->io; |
| |
| /* Get the bus range */ |
| ret = of_pci_parse_bus_range(np, &pcie->busn); |
| if (ret) { |
| dev_err(&pdev->dev, "failed to parse bus-range property: %d\n", |
| ret); |
| return ret; |
| } |
| |
| i = 0; |
| for_each_child_of_node(pdev->dev.of_node, child) { |
| if (!of_device_is_available(child)) |
| continue; |
| i++; |
| } |
| |
| pcie->ports = devm_kzalloc(&pdev->dev, i * |
| sizeof(struct mvebu_pcie_port), |
| GFP_KERNEL); |
| if (!pcie->ports) |
| return -ENOMEM; |
| |
| i = 0; |
| for_each_child_of_node(pdev->dev.of_node, child) { |
| struct mvebu_pcie_port *port = &pcie->ports[i]; |
| enum of_gpio_flags flags; |
| |
| if (!of_device_is_available(child)) |
| continue; |
| |
| port->pcie = pcie; |
| |
| if (of_property_read_u32(child, "marvell,pcie-port", |
| &port->port)) { |
| dev_warn(&pdev->dev, |
| "ignoring PCIe DT node, missing pcie-port property\n"); |
| continue; |
| } |
| |
| if (of_property_read_u32(child, "marvell,pcie-lane", |
| &port->lane)) |
| port->lane = 0; |
| |
| port->name = kasprintf(GFP_KERNEL, "pcie%d.%d", |
| port->port, port->lane); |
| |
| port->devfn = of_pci_get_devfn(child); |
| if (port->devfn < 0) |
| continue; |
| |
| ret = mvebu_get_tgt_attr(np, port->devfn, IORESOURCE_MEM, |
| &port->mem_target, &port->mem_attr); |
| if (ret < 0) { |
| dev_err(&pdev->dev, "PCIe%d.%d: cannot get tgt/attr for mem window\n", |
| port->port, port->lane); |
| continue; |
| } |
| |
| if (resource_size(&pcie->io) != 0) |
| mvebu_get_tgt_attr(np, port->devfn, IORESOURCE_IO, |
| &port->io_target, &port->io_attr); |
| else { |
| port->io_target = -1; |
| port->io_attr = -1; |
| } |
| |
| port->reset_gpio = of_get_named_gpio_flags(child, |
| "reset-gpios", 0, &flags); |
| if (gpio_is_valid(port->reset_gpio)) { |
| u32 reset_udelay = 20000; |
| |
| port->reset_active_low = flags & OF_GPIO_ACTIVE_LOW; |
| port->reset_name = kasprintf(GFP_KERNEL, |
| "pcie%d.%d-reset", port->port, port->lane); |
| of_property_read_u32(child, "reset-delay-us", |
| &reset_udelay); |
| |
| ret = devm_gpio_request_one(&pdev->dev, |
| port->reset_gpio, GPIOF_DIR_OUT, port->reset_name); |
| if (ret) { |
| if (ret == -EPROBE_DEFER) |
| return ret; |
| continue; |
| } |
| |
| gpio_set_value(port->reset_gpio, |
| (port->reset_active_low) ? 1 : 0); |
| msleep(reset_udelay/1000); |
| } |
| |
| port->clk = of_clk_get_by_name(child, NULL); |
| if (IS_ERR(port->clk)) { |
| dev_err(&pdev->dev, "PCIe%d.%d: cannot get clock\n", |
| port->port, port->lane); |
| continue; |
| } |
| |
| ret = clk_prepare_enable(port->clk); |
| if (ret) |
| continue; |
| |
| port->base = mvebu_pcie_map_registers(pdev, child, port); |
| if (IS_ERR(port->base)) { |
| dev_err(&pdev->dev, "PCIe%d.%d: cannot map registers\n", |
| port->port, port->lane); |
| port->base = NULL; |
| clk_disable_unprepare(port->clk); |
| continue; |
| } |
| |
| mvebu_pcie_set_local_dev_nr(port, 1); |
| |
| port->dn = child; |
| mvebu_sw_pci_bridge_init(port); |
| i++; |
| } |
| |
| pcie->nports = i; |
| |
| for (i = 0; i < (IO_SPACE_LIMIT - SZ_64K); i += SZ_64K) |
| pci_ioremap_io(i, pcie->io.start + i); |
| |
| mvebu_pcie_msi_enable(pcie); |
| mvebu_pcie_enable(pcie); |
| |
| return 0; |
| } |
| |
| static const struct of_device_id mvebu_pcie_of_match_table[] = { |
| { .compatible = "marvell,armada-xp-pcie", }, |
| { .compatible = "marvell,armada-370-pcie", }, |
| { .compatible = "marvell,dove-pcie", }, |
| { .compatible = "marvell,kirkwood-pcie", }, |
| {}, |
| }; |
| MODULE_DEVICE_TABLE(of, mvebu_pcie_of_match_table); |
| |
| static struct platform_driver mvebu_pcie_driver = { |
| .driver = { |
| .owner = THIS_MODULE, |
| .name = "mvebu-pcie", |
| .of_match_table = mvebu_pcie_of_match_table, |
| /* driver unloading/unbinding currently not supported */ |
| .suppress_bind_attrs = true, |
| }, |
| .probe = mvebu_pcie_probe, |
| }; |
| module_platform_driver(mvebu_pcie_driver); |
| |
| MODULE_AUTHOR("Thomas Petazzoni <thomas.petazzoni@free-electrons.com>"); |
| MODULE_DESCRIPTION("Marvell EBU PCIe driver"); |
| MODULE_LICENSE("GPL v2"); |