blob: 0dcb4164dc8368a9187b670c2a303c39cfdfa109 [file] [log] [blame]
/*
* Copyright (C) 2001-2004 by David Brownell
*
* This program is free software; you can redistribute it and/or modify it
* under the terms of the GNU General Public License as published by the
* Free Software Foundation; either version 2 of the License, or (at your
* option) any later version.
*
* This program is distributed in the hope that it will be useful, but
* WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY
* or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
* for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software Foundation,
* Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
*/
/* this file is part of ehci-hcd.c */
/*-------------------------------------------------------------------------*/
/*
* EHCI Root Hub ... the nonsharable stuff
*
* Registers don't need cpu_to_le32, that happens transparently
*/
/*-------------------------------------------------------------------------*/
#ifdef CONFIG_USB_PERSIST
static int ehci_hub_control(
struct usb_hcd *hcd,
u16 typeReq,
u16 wValue,
u16 wIndex,
char *buf,
u16 wLength
);
/* After a power loss, ports that were owned by the companion must be
* reset so that the companion can still own them.
*/
static void ehci_handover_companion_ports(struct ehci_hcd *ehci)
{
u32 __iomem *reg;
u32 status;
int port;
__le32 buf;
struct usb_hcd *hcd = ehci_to_hcd(ehci);
if (!ehci->owned_ports)
return;
/* Give the connections some time to appear */
msleep(20);
port = HCS_N_PORTS(ehci->hcs_params);
while (port--) {
if (test_bit(port, &ehci->owned_ports)) {
reg = &ehci->regs->port_status[port];
status = ehci_readl(ehci, reg) & ~PORT_RWC_BITS;
/* Port already owned by companion? */
if (status & PORT_OWNER)
clear_bit(port, &ehci->owned_ports);
else if (test_bit(port, &ehci->companion_ports))
ehci_writel(ehci, status & ~PORT_PE, reg);
else
ehci_hub_control(hcd, SetPortFeature,
USB_PORT_FEAT_RESET, port + 1,
NULL, 0);
}
}
if (!ehci->owned_ports)
return;
msleep(90); /* Wait for resets to complete */
port = HCS_N_PORTS(ehci->hcs_params);
while (port--) {
if (test_bit(port, &ehci->owned_ports)) {
ehci_hub_control(hcd, GetPortStatus,
0, port + 1,
(char *) &buf, sizeof(buf));
/* The companion should now own the port,
* but if something went wrong the port must not
* remain enabled.
*/
reg = &ehci->regs->port_status[port];
status = ehci_readl(ehci, reg) & ~PORT_RWC_BITS;
if (status & PORT_OWNER)
ehci_writel(ehci, status | PORT_CSC, reg);
else {
ehci_dbg(ehci, "failed handover port %d: %x\n",
port + 1, status);
ehci_writel(ehci, status & ~PORT_PE, reg);
}
}
}
ehci->owned_ports = 0;
}
#else /* CONFIG_USB_PERSIST */
static inline void ehci_handover_companion_ports(struct ehci_hcd *ehci)
{ }
#endif
#ifdef CONFIG_PM
static int ehci_bus_suspend (struct usb_hcd *hcd)
{
struct ehci_hcd *ehci = hcd_to_ehci (hcd);
int port;
int mask;
ehci_dbg(ehci, "suspend root hub\n");
if (time_before (jiffies, ehci->next_statechange))
msleep(5);
port = HCS_N_PORTS (ehci->hcs_params);
spin_lock_irq (&ehci->lock);
/* stop schedules, clean any completed work */
if (HC_IS_RUNNING(hcd->state)) {
ehci_quiesce (ehci);
hcd->state = HC_STATE_QUIESCING;
}
ehci->command = ehci_readl(ehci, &ehci->regs->command);
if (ehci->reclaim)
ehci->reclaim_ready = 1;
ehci_work(ehci);
/* Unlike other USB host controller types, EHCI doesn't have
* any notion of "global" or bus-wide suspend. The driver has
* to manually suspend all the active unsuspended ports, and
* then manually resume them in the bus_resume() routine.
*/
ehci->bus_suspended = 0;
ehci->owned_ports = 0;
while (port--) {
u32 __iomem *reg = &ehci->regs->port_status [port];
u32 t1 = ehci_readl(ehci, reg) & ~PORT_RWC_BITS;
u32 t2 = t1;
/* keep track of which ports we suspend */
if (t1 & PORT_OWNER)
set_bit(port, &ehci->owned_ports);
else if ((t1 & PORT_PE) && !(t1 & PORT_SUSPEND)) {
t2 |= PORT_SUSPEND;
set_bit(port, &ehci->bus_suspended);
}
/* enable remote wakeup on all ports */
if (device_may_wakeup(&hcd->self.root_hub->dev))
t2 |= PORT_WKOC_E|PORT_WKDISC_E|PORT_WKCONN_E;
else
t2 &= ~(PORT_WKOC_E|PORT_WKDISC_E|PORT_WKCONN_E);
if (t1 != t2) {
ehci_vdbg (ehci, "port %d, %08x -> %08x\n",
port + 1, t1, t2);
ehci_writel(ehci, t2, reg);
}
}
/* turn off now-idle HC */
del_timer_sync (&ehci->watchdog);
ehci_halt (ehci);
hcd->state = HC_STATE_SUSPENDED;
/* allow remote wakeup */
mask = INTR_MASK;
if (!device_may_wakeup(&hcd->self.root_hub->dev))
mask &= ~STS_PCD;
ehci_writel(ehci, mask, &ehci->regs->intr_enable);
ehci_readl(ehci, &ehci->regs->intr_enable);
ehci->next_statechange = jiffies + msecs_to_jiffies(10);
spin_unlock_irq (&ehci->lock);
return 0;
}
/* caller has locked the root hub, and should reset/reinit on error */
static int ehci_bus_resume (struct usb_hcd *hcd)
{
struct ehci_hcd *ehci = hcd_to_ehci (hcd);
u32 temp;
u32 power_okay;
int i;
if (time_before (jiffies, ehci->next_statechange))
msleep(5);
spin_lock_irq (&ehci->lock);
if (!test_bit(HCD_FLAG_HW_ACCESSIBLE, &hcd->flags)) {
spin_unlock_irq(&ehci->lock);
return -ESHUTDOWN;
}
/* Ideally and we've got a real resume here, and no port's power
* was lost. (For PCI, that means Vaux was maintained.) But we
* could instead be restoring a swsusp snapshot -- so that BIOS was
* the last user of the controller, not reset/pm hardware keeping
* state we gave to it.
*/
power_okay = ehci_readl(ehci, &ehci->regs->intr_enable);
ehci_dbg(ehci, "resume root hub%s\n",
power_okay ? "" : " after power loss");
/* at least some APM implementations will try to deliver
* IRQs right away, so delay them until we're ready.
*/
ehci_writel(ehci, 0, &ehci->regs->intr_enable);
/* re-init operational registers */
ehci_writel(ehci, 0, &ehci->regs->segment);
ehci_writel(ehci, ehci->periodic_dma, &ehci->regs->frame_list);
ehci_writel(ehci, (u32) ehci->async->qh_dma, &ehci->regs->async_next);
/* restore CMD_RUN, framelist size, and irq threshold */
ehci_writel(ehci, ehci->command, &ehci->regs->command);
/* Some controller/firmware combinations need a delay during which
* they set up the port statuses. See Bugzilla #8190. */
mdelay(8);
/* manually resume the ports we suspended during bus_suspend() */
i = HCS_N_PORTS (ehci->hcs_params);
while (i--) {
temp = ehci_readl(ehci, &ehci->regs->port_status [i]);
temp &= ~(PORT_RWC_BITS
| PORT_WKOC_E | PORT_WKDISC_E | PORT_WKCONN_E);
if (test_bit(i, &ehci->bus_suspended) &&
(temp & PORT_SUSPEND)) {
ehci->reset_done [i] = jiffies + msecs_to_jiffies (20);
temp |= PORT_RESUME;
}
ehci_writel(ehci, temp, &ehci->regs->port_status [i]);
}
i = HCS_N_PORTS (ehci->hcs_params);
mdelay (20);
while (i--) {
temp = ehci_readl(ehci, &ehci->regs->port_status [i]);
if (test_bit(i, &ehci->bus_suspended) &&
(temp & PORT_SUSPEND)) {
temp &= ~(PORT_RWC_BITS | PORT_RESUME);
ehci_writel(ehci, temp, &ehci->regs->port_status [i]);
ehci_vdbg (ehci, "resumed port %d\n", i + 1);
}
}
(void) ehci_readl(ehci, &ehci->regs->command);
/* maybe re-activate the schedule(s) */
temp = 0;
if (ehci->async->qh_next.qh)
temp |= CMD_ASE;
if (ehci->periodic_sched)
temp |= CMD_PSE;
if (temp) {
ehci->command |= temp;
ehci_writel(ehci, ehci->command, &ehci->regs->command);
}
ehci->next_statechange = jiffies + msecs_to_jiffies(5);
hcd->state = HC_STATE_RUNNING;
/* Now we can safely re-enable irqs */
ehci_writel(ehci, INTR_MASK, &ehci->regs->intr_enable);
spin_unlock_irq (&ehci->lock);
if (!power_okay)
ehci_handover_companion_ports(ehci);
return 0;
}
#else
#define ehci_bus_suspend NULL
#define ehci_bus_resume NULL
#endif /* CONFIG_PM */
/*-------------------------------------------------------------------------*/
/* Display the ports dedicated to the companion controller */
static ssize_t show_companion(struct class_device *class_dev, char *buf)
{
struct ehci_hcd *ehci;
int nports, index, n;
int count = PAGE_SIZE;
char *ptr = buf;
ehci = hcd_to_ehci(bus_to_hcd(class_get_devdata(class_dev)));
nports = HCS_N_PORTS(ehci->hcs_params);
for (index = 0; index < nports; ++index) {
if (test_bit(index, &ehci->companion_ports)) {
n = scnprintf(ptr, count, "%d\n", index + 1);
ptr += n;
count -= n;
}
}
return ptr - buf;
}
/*
* Dedicate or undedicate a port to the companion controller.
* Syntax is "[-]portnum", where a leading '-' sign means
* return control of the port to the EHCI controller.
*/
static ssize_t store_companion(struct class_device *class_dev,
const char *buf, size_t count)
{
struct ehci_hcd *ehci;
int portnum, new_owner, try;
u32 __iomem *status_reg;
u32 port_status;
ehci = hcd_to_ehci(bus_to_hcd(class_get_devdata(class_dev)));
new_owner = PORT_OWNER; /* Owned by companion */
if (sscanf(buf, "%d", &portnum) != 1)
return -EINVAL;
if (portnum < 0) {
portnum = - portnum;
new_owner = 0; /* Owned by EHCI */
}
if (portnum <= 0 || portnum > HCS_N_PORTS(ehci->hcs_params))
return -ENOENT;
status_reg = &ehci->regs->port_status[--portnum];
if (new_owner)
set_bit(portnum, &ehci->companion_ports);
else
clear_bit(portnum, &ehci->companion_ports);
/*
* The controller won't set the OWNER bit if the port is
* enabled, so this loop will sometimes require at least two
* iterations: one to disable the port and one to set OWNER.
*/
for (try = 4; try > 0; --try) {
spin_lock_irq(&ehci->lock);
port_status = ehci_readl(ehci, status_reg);
if ((port_status & PORT_OWNER) == new_owner
|| (port_status & (PORT_OWNER | PORT_CONNECT))
== 0)
try = 0;
else {
port_status ^= PORT_OWNER;
port_status &= ~(PORT_PE | PORT_RWC_BITS);
ehci_writel(ehci, port_status, status_reg);
}
spin_unlock_irq(&ehci->lock);
if (try > 1)
msleep(5);
}
return count;
}
static CLASS_DEVICE_ATTR(companion, 0644, show_companion, store_companion);
static inline void create_companion_file(struct ehci_hcd *ehci)
{
int i;
/* with integrated TT there is no companion! */
if (!ehci_is_TDI(ehci))
i = class_device_create_file(ehci_to_hcd(ehci)->self.class_dev,
&class_device_attr_companion);
}
static inline void remove_companion_file(struct ehci_hcd *ehci)
{
/* with integrated TT there is no companion! */
if (!ehci_is_TDI(ehci))
class_device_remove_file(ehci_to_hcd(ehci)->self.class_dev,
&class_device_attr_companion);
}
/*-------------------------------------------------------------------------*/
static int check_reset_complete (
struct ehci_hcd *ehci,
int index,
u32 __iomem *status_reg,
int port_status
) {
if (!(port_status & PORT_CONNECT)) {
ehci->reset_done [index] = 0;
return port_status;
}
/* if reset finished and it's still not enabled -- handoff */
if (!(port_status & PORT_PE)) {
/* with integrated TT, there's nobody to hand it to! */
if (ehci_is_TDI(ehci)) {
ehci_dbg (ehci,
"Failed to enable port %d on root hub TT\n",
index+1);
return port_status;
}
ehci_dbg (ehci, "port %d full speed --> companion\n",
index + 1);
// what happens if HCS_N_CC(params) == 0 ?
port_status |= PORT_OWNER;
port_status &= ~PORT_RWC_BITS;
ehci_writel(ehci, port_status, status_reg);
} else
ehci_dbg (ehci, "port %d high speed\n", index + 1);
return port_status;
}
/*-------------------------------------------------------------------------*/
/* build "status change" packet (one or two bytes) from HC registers */
static int
ehci_hub_status_data (struct usb_hcd *hcd, char *buf)
{
struct ehci_hcd *ehci = hcd_to_ehci (hcd);
u32 temp, status = 0;
u32 mask;
int ports, i, retval = 1;
unsigned long flags;
/* if !USB_SUSPEND, root hub timers won't get shut down ... */
if (!HC_IS_RUNNING(hcd->state))
return 0;
/* init status to no-changes */
buf [0] = 0;
ports = HCS_N_PORTS (ehci->hcs_params);
if (ports > 7) {
buf [1] = 0;
retval++;
}
/* Some boards (mostly VIA?) report bogus overcurrent indications,
* causing massive log spam unless we completely ignore them. It
* may be relevant that VIA VT8235 controlers, where PORT_POWER is
* always set, seem to clear PORT_OCC and PORT_CSC when writing to
* PORT_POWER; that's surprising, but maybe within-spec.
*/
if (!ignore_oc)
mask = PORT_CSC | PORT_PEC | PORT_OCC;
else
mask = PORT_CSC | PORT_PEC;
// PORT_RESUME from hardware ~= PORT_STAT_C_SUSPEND
/* no hub change reports (bit 0) for now (power, ...) */
/* port N changes (bit N)? */
spin_lock_irqsave (&ehci->lock, flags);
for (i = 0; i < ports; i++) {
temp = ehci_readl(ehci, &ehci->regs->port_status [i]);
/*
* Return status information even for ports with OWNER set.
* Otherwise khubd wouldn't see the disconnect event when a
* high-speed device is switched over to the companion
* controller by the user.
*/
if (!(temp & PORT_CONNECT))
ehci->reset_done [i] = 0;
if ((temp & mask) != 0
|| ((temp & PORT_RESUME) != 0
&& time_after_eq(jiffies,
ehci->reset_done[i]))) {
if (i < 7)
buf [0] |= 1 << (i + 1);
else
buf [1] |= 1 << (i - 7);
status = STS_PCD;
}
}
/* FIXME autosuspend idle root hubs */
spin_unlock_irqrestore (&ehci->lock, flags);
return status ? retval : 0;
}
/*-------------------------------------------------------------------------*/
static void
ehci_hub_descriptor (
struct ehci_hcd *ehci,
struct usb_hub_descriptor *desc
) {
int ports = HCS_N_PORTS (ehci->hcs_params);
u16 temp;
desc->bDescriptorType = 0x29;
desc->bPwrOn2PwrGood = 10; /* ehci 1.0, 2.3.9 says 20ms max */
desc->bHubContrCurrent = 0;
desc->bNbrPorts = ports;
temp = 1 + (ports / 8);
desc->bDescLength = 7 + 2 * temp;
/* two bitmaps: ports removable, and usb 1.0 legacy PortPwrCtrlMask */
memset (&desc->bitmap [0], 0, temp);
memset (&desc->bitmap [temp], 0xff, temp);
temp = 0x0008; /* per-port overcurrent reporting */
if (HCS_PPC (ehci->hcs_params))
temp |= 0x0001; /* per-port power control */
else
temp |= 0x0002; /* no power switching */
#if 0
// re-enable when we support USB_PORT_FEAT_INDICATOR below.
if (HCS_INDICATOR (ehci->hcs_params))
temp |= 0x0080; /* per-port indicators (LEDs) */
#endif
desc->wHubCharacteristics = (__force __u16)cpu_to_le16 (temp);
}
/*-------------------------------------------------------------------------*/
#define PORT_WAKE_BITS (PORT_WKOC_E|PORT_WKDISC_E|PORT_WKCONN_E)
static int ehci_hub_control (
struct usb_hcd *hcd,
u16 typeReq,
u16 wValue,
u16 wIndex,
char *buf,
u16 wLength
) {
struct ehci_hcd *ehci = hcd_to_ehci (hcd);
int ports = HCS_N_PORTS (ehci->hcs_params);
u32 __iomem *status_reg = &ehci->regs->port_status[
(wIndex & 0xff) - 1];
u32 temp, status;
unsigned long flags;
int retval = 0;
unsigned selector;
/*
* FIXME: support SetPortFeatures USB_PORT_FEAT_INDICATOR.
* HCS_INDICATOR may say we can change LEDs to off/amber/green.
* (track current state ourselves) ... blink for diagnostics,
* power, "this is the one", etc. EHCI spec supports this.
*/
spin_lock_irqsave (&ehci->lock, flags);
switch (typeReq) {
case ClearHubFeature:
switch (wValue) {
case C_HUB_LOCAL_POWER:
case C_HUB_OVER_CURRENT:
/* no hub-wide feature/status flags */
break;
default:
goto error;
}
break;
case ClearPortFeature:
if (!wIndex || wIndex > ports)
goto error;
wIndex--;
temp = ehci_readl(ehci, status_reg);
/*
* Even if OWNER is set, so the port is owned by the
* companion controller, khubd needs to be able to clear
* the port-change status bits (especially
* USB_PORT_FEAT_C_CONNECTION).
*/
switch (wValue) {
case USB_PORT_FEAT_ENABLE:
ehci_writel(ehci, temp & ~PORT_PE, status_reg);
break;
case USB_PORT_FEAT_C_ENABLE:
ehci_writel(ehci, (temp & ~PORT_RWC_BITS) | PORT_PEC,
status_reg);
break;
case USB_PORT_FEAT_SUSPEND:
if (temp & PORT_RESET)
goto error;
if (ehci->no_selective_suspend)
break;
if (temp & PORT_SUSPEND) {
if ((temp & PORT_PE) == 0)
goto error;
/* resume signaling for 20 msec */
temp &= ~(PORT_RWC_BITS | PORT_WAKE_BITS);
ehci_writel(ehci, temp | PORT_RESUME,
status_reg);
ehci->reset_done [wIndex] = jiffies
+ msecs_to_jiffies (20);
}
break;
case USB_PORT_FEAT_C_SUSPEND:
/* we auto-clear this feature */
break;
case USB_PORT_FEAT_POWER:
if (HCS_PPC (ehci->hcs_params))
ehci_writel(ehci,
temp & ~(PORT_RWC_BITS | PORT_POWER),
status_reg);
break;
case USB_PORT_FEAT_C_CONNECTION:
ehci_writel(ehci, (temp & ~PORT_RWC_BITS) | PORT_CSC,
status_reg);
break;
case USB_PORT_FEAT_C_OVER_CURRENT:
ehci_writel(ehci, (temp & ~PORT_RWC_BITS) | PORT_OCC,
status_reg);
break;
case USB_PORT_FEAT_C_RESET:
/* GetPortStatus clears reset */
break;
default:
goto error;
}
ehci_readl(ehci, &ehci->regs->command); /* unblock posted write */
break;
case GetHubDescriptor:
ehci_hub_descriptor (ehci, (struct usb_hub_descriptor *)
buf);
break;
case GetHubStatus:
/* no hub-wide feature/status flags */
memset (buf, 0, 4);
//cpu_to_le32s ((u32 *) buf);
break;
case GetPortStatus:
if (!wIndex || wIndex > ports)
goto error;
wIndex--;
status = 0;
temp = ehci_readl(ehci, status_reg);
// wPortChange bits
if (temp & PORT_CSC)
status |= 1 << USB_PORT_FEAT_C_CONNECTION;
if (temp & PORT_PEC)
status |= 1 << USB_PORT_FEAT_C_ENABLE;
if ((temp & PORT_OCC) && !ignore_oc){
status |= 1 << USB_PORT_FEAT_C_OVER_CURRENT;
/*
* Hubs should disable port power on over-current.
* However, not all EHCI implementations do this
* automatically, even if they _do_ support per-port
* power switching; they're allowed to just limit the
* current. khubd will turn the power back on.
*/
if (HCS_PPC (ehci->hcs_params)){
ehci_writel(ehci,
temp & ~(PORT_RWC_BITS | PORT_POWER),
status_reg);
}
}
/* whoever resumes must GetPortStatus to complete it!! */
if (temp & PORT_RESUME) {
/* Remote Wakeup received? */
if (!ehci->reset_done[wIndex]) {
/* resume signaling for 20 msec */
ehci->reset_done[wIndex] = jiffies
+ msecs_to_jiffies(20);
/* check the port again */
mod_timer(&ehci_to_hcd(ehci)->rh_timer,
ehci->reset_done[wIndex]);
}
/* resume completed? */
else if (time_after_eq(jiffies,
ehci->reset_done[wIndex])) {
status |= 1 << USB_PORT_FEAT_C_SUSPEND;
ehci->reset_done[wIndex] = 0;
/* stop resume signaling */
temp = ehci_readl(ehci, status_reg);
ehci_writel(ehci,
temp & ~(PORT_RWC_BITS | PORT_RESUME),
status_reg);
retval = handshake(ehci, status_reg,
PORT_RESUME, 0, 2000 /* 2msec */);
if (retval != 0) {
ehci_err(ehci,
"port %d resume error %d\n",
wIndex + 1, retval);
goto error;
}
temp &= ~(PORT_SUSPEND|PORT_RESUME|(3<<10));
}
}
/* whoever resets must GetPortStatus to complete it!! */
if ((temp & PORT_RESET)
&& time_after_eq(jiffies,
ehci->reset_done[wIndex])) {
status |= 1 << USB_PORT_FEAT_C_RESET;
ehci->reset_done [wIndex] = 0;
/* force reset to complete */
ehci_writel(ehci, temp & ~(PORT_RWC_BITS | PORT_RESET),
status_reg);
/* REVISIT: some hardware needs 550+ usec to clear
* this bit; seems too long to spin routinely...
*/
retval = handshake(ehci, status_reg,
PORT_RESET, 0, 750);
if (retval != 0) {
ehci_err (ehci, "port %d reset error %d\n",
wIndex + 1, retval);
goto error;
}
/* see what we found out */
temp = check_reset_complete (ehci, wIndex, status_reg,
ehci_readl(ehci, status_reg));
}
/* transfer dedicated ports to the companion hc */
if ((temp & PORT_CONNECT) &&
test_bit(wIndex, &ehci->companion_ports)) {
temp &= ~PORT_RWC_BITS;
temp |= PORT_OWNER;
ehci_writel(ehci, temp, status_reg);
ehci_dbg(ehci, "port %d --> companion\n", wIndex + 1);
temp = ehci_readl(ehci, status_reg);
}
/*
* Even if OWNER is set, there's no harm letting khubd
* see the wPortStatus values (they should all be 0 except
* for PORT_POWER anyway).
*/
if (temp & PORT_CONNECT) {
status |= 1 << USB_PORT_FEAT_CONNECTION;
// status may be from integrated TT
status |= ehci_port_speed(ehci, temp);
}
if (temp & PORT_PE)
status |= 1 << USB_PORT_FEAT_ENABLE;
if (temp & (PORT_SUSPEND|PORT_RESUME))
status |= 1 << USB_PORT_FEAT_SUSPEND;
if (temp & PORT_OC)
status |= 1 << USB_PORT_FEAT_OVER_CURRENT;
if (temp & PORT_RESET)
status |= 1 << USB_PORT_FEAT_RESET;
if (temp & PORT_POWER)
status |= 1 << USB_PORT_FEAT_POWER;
#ifndef EHCI_VERBOSE_DEBUG
if (status & ~0xffff) /* only if wPortChange is interesting */
#endif
dbg_port (ehci, "GetStatus", wIndex + 1, temp);
put_unaligned(cpu_to_le32 (status), (__le32 *) buf);
break;
case SetHubFeature:
switch (wValue) {
case C_HUB_LOCAL_POWER:
case C_HUB_OVER_CURRENT:
/* no hub-wide feature/status flags */
break;
default:
goto error;
}
break;
case SetPortFeature:
selector = wIndex >> 8;
wIndex &= 0xff;
if (!wIndex || wIndex > ports)
goto error;
wIndex--;
temp = ehci_readl(ehci, status_reg);
if (temp & PORT_OWNER)
break;
temp &= ~PORT_RWC_BITS;
switch (wValue) {
case USB_PORT_FEAT_SUSPEND:
if (ehci->no_selective_suspend)
break;
if ((temp & PORT_PE) == 0
|| (temp & PORT_RESET) != 0)
goto error;
if (device_may_wakeup(&hcd->self.root_hub->dev))
temp |= PORT_WAKE_BITS;
ehci_writel(ehci, temp | PORT_SUSPEND, status_reg);
break;
case USB_PORT_FEAT_POWER:
if (HCS_PPC (ehci->hcs_params))
ehci_writel(ehci, temp | PORT_POWER,
status_reg);
break;
case USB_PORT_FEAT_RESET:
if (temp & PORT_RESUME)
goto error;
/* line status bits may report this as low speed,
* which can be fine if this root hub has a
* transaction translator built in.
*/
if ((temp & (PORT_PE|PORT_CONNECT)) == PORT_CONNECT
&& !ehci_is_TDI(ehci)
&& PORT_USB11 (temp)) {
ehci_dbg (ehci,
"port %d low speed --> companion\n",
wIndex + 1);
temp |= PORT_OWNER;
} else {
ehci_vdbg (ehci, "port %d reset\n", wIndex + 1);
temp |= PORT_RESET;
temp &= ~PORT_PE;
/*
* caller must wait, then call GetPortStatus
* usb 2.0 spec says 50 ms resets on root
*/
ehci->reset_done [wIndex] = jiffies
+ msecs_to_jiffies (50);
}
ehci_writel(ehci, temp, status_reg);
break;
/* For downstream facing ports (these): one hub port is put
* into test mode according to USB2 11.24.2.13, then the hub
* must be reset (which for root hub now means rmmod+modprobe,
* or else system reboot). See EHCI 2.3.9 and 4.14 for info
* about the EHCI-specific stuff.
*/
case USB_PORT_FEAT_TEST:
if (!selector || selector > 5)
goto error;
ehci_quiesce(ehci);
ehci_halt(ehci);
temp |= selector << 16;
ehci_writel(ehci, temp, status_reg);
break;
default:
goto error;
}
ehci_readl(ehci, &ehci->regs->command); /* unblock posted writes */
break;
default:
error:
/* "stall" on error */
retval = -EPIPE;
}
spin_unlock_irqrestore (&ehci->lock, flags);
return retval;
}