ath9k: Enable Bluetooth Coexistence support
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
diff --git a/drivers/net/wireless/ath9k/ath9k.h b/drivers/net/wireless/ath9k/ath9k.h
index adcd342..f2ad625 100644
--- a/drivers/net/wireless/ath9k/ath9k.h
+++ b/drivers/net/wireless/ath9k/ath9k.h
@@ -198,6 +198,7 @@
ATH9K_HW_CAP_AUTOSLEEP = BIT(19),
ATH9K_HW_CAP_4KB_SPLITTRANS = BIT(20),
ATH9K_HW_CAP_WOW_MATCHPATTERN_EXACT = BIT(21),
+ ATH9K_HW_CAP_BT_COEX = BIT(22)
};
enum ath9k_capability_type {
@@ -752,6 +753,7 @@
#define AR_GPIO_OUTPUT_MUX_AS_OUTPUT 0
#define AR_GPIO_OUTPUT_MUX_AS_PCIE_ATTENTION_LED 1
#define AR_GPIO_OUTPUT_MUX_AS_PCIE_POWER_LED 2
+#define AR_GPIO_OUTPUT_MUX_AS_TX_FRAME 3
#define AR_GPIO_OUTPUT_MUX_AS_MAC_NETWORK_LED 5
#define AR_GPIO_OUTPUT_MUX_AS_MAC_POWER_LED 6
@@ -801,6 +803,8 @@
u16 ah_rfsilent;
u32 ah_rfkill_gpio;
u32 ah_rfkill_polarity;
+ u32 ah_btactive_gpio;
+ u32 ah_wlanactive_gpio;
#ifndef ATH_NF_PER_CHAN
struct ath9k_nfcal_hist nfCalHist[NUM_NF_READINGS];
@@ -1050,5 +1054,6 @@
void ath9k_hw_startpcureceive(struct ath_hal *ah);
void ath9k_hw_stoppcurecv(struct ath_hal *ah);
bool ath9k_hw_stopdmarecv(struct ath_hal *ah);
+void ath9k_hw_btcoex_enable(struct ath_hal *ah);
#endif
diff --git a/drivers/net/wireless/ath9k/hw.c b/drivers/net/wireless/ath9k/hw.c
index 19144ca..3c026e6 100644
--- a/drivers/net/wireless/ath9k/hw.c
+++ b/drivers/net/wireless/ath9k/hw.c
@@ -3341,6 +3341,12 @@
pCap->num_antcfg_2ghz =
ath9k_hw_get_num_ant_config(ah, ATH9K_HAL_FREQ_BAND_2GHZ);
+ if (AR_SREV_9280_10_OR_LATER(ah)) {
+ pCap->hw_caps |= ATH9K_HW_CAP_BT_COEX;
+ ah->ah_btactive_gpio = 6;
+ ah->ah_wlanactive_gpio = 5;
+ }
+
return true;
}
@@ -3836,3 +3842,30 @@
REG_WRITE(ah, AR_2040_MODE, macmode);
}
+
+/***************************/
+/* Bluetooth Coexistence */
+/***************************/
+
+void ath9k_hw_btcoex_enable(struct ath_hal *ah)
+{
+ /* connect bt_active to baseband */
+ REG_CLR_BIT(ah, AR_GPIO_INPUT_EN_VAL,
+ (AR_GPIO_INPUT_EN_VAL_BT_PRIORITY_DEF |
+ AR_GPIO_INPUT_EN_VAL_BT_FREQUENCY_DEF));
+
+ REG_SET_BIT(ah, AR_GPIO_INPUT_EN_VAL,
+ AR_GPIO_INPUT_EN_VAL_BT_ACTIVE_BB);
+
+ /* Set input mux for bt_active to gpio pin */
+ REG_RMW_FIELD(ah, AR_GPIO_INPUT_MUX1,
+ AR_GPIO_INPUT_MUX1_BT_ACTIVE,
+ ah->ah_btactive_gpio);
+
+ /* Configure the desired gpio port for input */
+ ath9k_hw_cfg_gpio_input(ah, ah->ah_btactive_gpio);
+
+ /* Configure the desired GPIO port for TX_FRAME output */
+ ath9k_hw_cfg_output(ah, ah->ah_wlanactive_gpio,
+ AR_GPIO_OUTPUT_MUX_AS_TX_FRAME);
+}
diff --git a/drivers/net/wireless/ath9k/main.c b/drivers/net/wireless/ath9k/main.c
index 9c1fb96..8929b02 100644
--- a/drivers/net/wireless/ath9k/main.c
+++ b/drivers/net/wireless/ath9k/main.c
@@ -431,12 +431,14 @@
/*
* Update tx/rx chainmask. For legacy association,
* hard code chainmask to 1x1, for 11n association, use
- * the chainmask configuration.
+ * the chainmask configuration, for bt coexistence, use
+ * the chainmask configuration even in legacy mode.
*/
static void ath_update_chainmask(struct ath_softc *sc, int is_ht)
{
sc->sc_flags |= SC_OP_CHAINMASK_UPDATE;
- if (is_ht) {
+ if (is_ht ||
+ (sc->sc_ah->ah_caps.hw_caps & ATH9K_HW_CAP_BT_COEX)) {
sc->sc_tx_chainmask = sc->sc_ah->ah_caps.tx_chainmask;
sc->sc_rx_chainmask = sc->sc_ah->ah_caps.rx_chainmask;
} else {
@@ -1519,6 +1521,9 @@
sc->sbands[IEEE80211_BAND_5GHZ].band = IEEE80211_BAND_5GHZ;
}
+ if (sc->sc_ah->ah_caps.hw_caps & ATH9K_HW_CAP_BT_COEX)
+ ath9k_hw_btcoex_enable(sc->sc_ah);
+
return 0;
bad2:
/* cleanup tx queues */
diff --git a/drivers/net/wireless/ath9k/reg.h b/drivers/net/wireless/ath9k/reg.h
index 8cc9bef..9a61522 100644
--- a/drivers/net/wireless/ath9k/reg.h
+++ b/drivers/net/wireless/ath9k/reg.h
@@ -897,14 +897,24 @@
#define AR_GPIO_INTR_POL_VAL_S 0
#define AR_GPIO_INPUT_EN_VAL 0x4054
+#define AR_GPIO_INPUT_EN_VAL_BT_PRIORITY_DEF 0x00000004
+#define AR_GPIO_INPUT_EN_VAL_BT_PRIORITY_S 2
+#define AR_GPIO_INPUT_EN_VAL_BT_FREQUENCY_DEF 0x00000008
+#define AR_GPIO_INPUT_EN_VAL_BT_FREQUENCY_S 3
+#define AR_GPIO_INPUT_EN_VAL_BT_ACTIVE_DEF 0x00000010
+#define AR_GPIO_INPUT_EN_VAL_BT_ACTIVE_S 4
#define AR_GPIO_INPUT_EN_VAL_RFSILENT_DEF 0x00000080
#define AR_GPIO_INPUT_EN_VAL_RFSILENT_DEF_S 7
+#define AR_GPIO_INPUT_EN_VAL_BT_ACTIVE_BB 0x00001000
+#define AR_GPIO_INPUT_EN_VAL_BT_ACTIVE_BB_S 12
#define AR_GPIO_INPUT_EN_VAL_RFSILENT_BB 0x00008000
#define AR_GPIO_INPUT_EN_VAL_RFSILENT_BB_S 15
#define AR_GPIO_RTC_RESET_OVERRIDE_ENABLE 0x00010000
#define AR_GPIO_JTAG_DISABLE 0x00020000
#define AR_GPIO_INPUT_MUX1 0x4058
+#define AR_GPIO_INPUT_MUX1_BT_ACTIVE 0x000f0000
+#define AR_GPIO_INPUT_MUX1_BT_ACTIVE_S 16
#define AR_GPIO_INPUT_MUX2 0x405c
#define AR_GPIO_INPUT_MUX2_CLK25 0x0000000f