mfd: Add manual ab8500-gpadc batt temp activation for AB8500 3.0
In AB8500 3.0 the pull-up supplying the NTC must be manually activated.
Add enumerators to chip version detection logic.
Signed-off-by: Kalle Komierowski <karl.komierowski@stericsson.com>
Reviewed-by: Johan Palsson <johan.palsson@stericsson.com>
Reviewed-by: Daniel Willerud <daniel.willerud@stericsson.com>
Reviewed-by: Jonas Aberg <jonas.aberg@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
diff --git a/drivers/mfd/ab8500-gpadc.c b/drivers/mfd/ab8500-gpadc.c
index 6421ad1..82708c1 100644
--- a/drivers/mfd/ab8500-gpadc.c
+++ b/drivers/mfd/ab8500-gpadc.c
@@ -57,6 +57,7 @@
#define SW_AVG_16 0x60
#define ADC_SW_CONV 0x04
#define EN_ICHAR 0x80
+#define BATTEMP_PULLUP 0x04
#define EN_BUF 0x40
#define DIS_ZERO 0x00
#define GPADC_BUSY 0x01
@@ -101,6 +102,7 @@
/**
* struct ab8500_gpadc - AB8500 GPADC device information
+ * @chip_id ABB chip id
* @dev: pointer to the struct device
* @node: a list of AB8500 GPADCs, hence prepared for
reentrance
@@ -112,6 +114,7 @@
* @cal_data array of ADC calibration data structs
*/
struct ab8500_gpadc {
+ u8 chip_id;
struct device *dev;
struct list_head node;
struct completion ab8500_gpadc_complete;
@@ -274,6 +277,7 @@
dev_err(gpadc->dev, "gpadc_conversion: enable gpadc failed\n");
goto out;
}
+
/* Select the input source and set average samples to 16 */
ret = abx500_set_register_interruptible(gpadc->dev, AB8500_GPADC,
AB8500_GPADC_CTRL2_REG, (input | SW_AVG_16));
@@ -282,9 +286,11 @@
"gpadc_conversion: set avg samples failed\n");
goto out;
}
+
/*
* Enable ADC, buffering, select rising edge and enable ADC path
- * charging current sense if it needed
+ * charging current sense if it needed, ABB 3.0 needs some special
+ * treatment too.
*/
switch (input) {
case MAIN_CHARGER_C:
@@ -294,6 +300,23 @@
EN_BUF | EN_ICHAR,
EN_BUF | EN_ICHAR);
break;
+ case BTEMP_BALL:
+ if (gpadc->chip_id >= AB8500_CUT3P0) {
+ /* Turn on btemp pull-up on ABB 3.0 */
+ ret = abx500_mask_and_set_register_interruptible(
+ gpadc->dev,
+ AB8500_GPADC, AB8500_GPADC_CTRL1_REG,
+ EN_BUF | BATTEMP_PULLUP,
+ EN_BUF | BATTEMP_PULLUP);
+
+ /*
+ * Delay might be needed for ABB8500 cut 3.0, if not, remove
+ * when hardware will be availible
+ */
+ msleep(1);
+ break;
+ }
+ /* Intentional fallthrough */
default:
ret = abx500_mask_and_set_register_interruptible(gpadc->dev,
AB8500_GPADC, AB8500_GPADC_CTRL1_REG, EN_BUF, EN_BUF);
@@ -304,6 +327,7 @@
"gpadc_conversion: select falling edge failed\n");
goto out;
}
+
ret = abx500_mask_and_set_register_interruptible(gpadc->dev,
AB8500_GPADC, AB8500_GPADC_CTRL1_REG, ADC_SW_CONV, ADC_SW_CONV);
if (ret < 0) {
@@ -552,6 +576,14 @@
goto fail;
}
+ /* Get Chip ID of the ABB ASIC */
+ ret = abx500_get_chip_id(gpadc->dev);
+ if (ret < 0) {
+ dev_err(gpadc->dev, "failed to get chip ID\n");
+ goto fail_irq;
+ }
+ gpadc->chip_id = (u8) ret;
+
/* VTVout LDO used to power up ab8500-GPADC */
gpadc->regu = regulator_get(&pdev->dev, "vddadc");
if (IS_ERR(gpadc->regu)) {