powerpc/fsl: Refactor device bindings
Moved Freescale SoC related bindings out of booting-without-of.txt and into
their own files.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
diff --git a/Documentation/powerpc/booting-without-of.txt b/Documentation/powerpc/booting-without-of.txt
index f6394b50..de2e5c0 100644
--- a/Documentation/powerpc/booting-without-of.txt
+++ b/Documentation/powerpc/booting-without-of.txt
@@ -41,27 +41,12 @@
VI - System-on-a-chip devices and nodes
1) Defining child nodes of an SOC
2) Representing devices without a current OF specification
- a) MDIO IO device
- b) Gianfar-compatible ethernet nodes
- c) PHY nodes
- d) Interrupt controllers
- e) I2C
- f) Freescale SOC USB controllers
- g) Freescale SOC SEC Security Engines
- h) Board Control and Status (BCSR)
- i) Freescale QUICC Engine module (QE)
- j) CFI or JEDEC memory-mapped NOR flash
- k) Global Utilities Block
- l) Freescale Communications Processor Module
- m) Chipselect/Local Bus
- n) 4xx/Axon EMAC ethernet nodes
- o) Xilinx IP cores
- p) Freescale Synchronous Serial Interface
- q) USB EHCI controllers
- r) Freescale Display Interface Unit
- s) Freescale on board FPGA
- t) Freescael MSI interrupt controller
- u) Freescale General-purpose Timers Module
+ a) PHY nodes
+ b) Interrupt controllers
+ c) CFI or JEDEC memory-mapped NOR flash
+ d) 4xx/Axon EMAC ethernet nodes
+ e) Xilinx IP cores
+ f) USB EHCI controllers
VII - Marvell Discovery mv64[345]6x System Controller chips
1) The /system-controller node
@@ -1250,80 +1235,7 @@
defined; this list will expand as more and more SOC-containing
platforms are moved over to use the flattened-device-tree model.
- a) MDIO IO device
-
- The MDIO is a bus to which the PHY devices are connected. For each
- device that exists on this bus, a child node should be created. See
- the definition of the PHY node below for an example of how to define
- a PHY.
-
- Required properties:
- - reg : Offset and length of the register set for the device
- - compatible : Should define the compatible device type for the
- mdio. Currently, this is most likely to be "fsl,gianfar-mdio"
-
- Example:
-
- mdio@24520 {
- reg = <24520 20>;
- compatible = "fsl,gianfar-mdio";
-
- ethernet-phy@0 {
- ......
- };
- };
-
-
- b) Gianfar-compatible ethernet nodes
-
- Required properties:
-
- - device_type : Should be "network"
- - model : Model of the device. Can be "TSEC", "eTSEC", or "FEC"
- - compatible : Should be "gianfar"
- - reg : Offset and length of the register set for the device
- - mac-address : List of bytes representing the ethernet address of
- this controller
- - interrupts : <a b> where a is the interrupt number and b is a
- field that represents an encoding of the sense and level
- information for the interrupt. This should be encoded based on
- the information in section 2) depending on the type of interrupt
- controller you have.
- - interrupt-parent : the phandle for the interrupt controller that
- services interrupts for this device.
- - phy-handle : The phandle for the PHY connected to this ethernet
- controller.
- - fixed-link : <a b c d e> where a is emulated phy id - choose any,
- but unique to the all specified fixed-links, b is duplex - 0 half,
- 1 full, c is link speed - d#10/d#100/d#1000, d is pause - 0 no
- pause, 1 pause, e is asym_pause - 0 no asym_pause, 1 asym_pause.
-
- Recommended properties:
-
- - phy-connection-type : a string naming the controller/PHY interface type,
- i.e., "mii" (default), "rmii", "gmii", "rgmii", "rgmii-id", "sgmii",
- "tbi", or "rtbi". This property is only really needed if the connection
- is of type "rgmii-id", as all other connection types are detected by
- hardware.
-
-
- Example:
-
- ethernet@24000 {
- #size-cells = <0>;
- device_type = "network";
- model = "TSEC";
- compatible = "gianfar";
- reg = <24000 1000>;
- mac-address = [ 00 E0 0C 00 73 00 ];
- interrupts = <d 3 e 3 12 3>;
- interrupt-parent = <40000>;
- phy-handle = <2452000>
- };
-
-
-
- c) PHY nodes
+ a) PHY nodes
Required properties:
@@ -1351,7 +1263,7 @@
};
- d) Interrupt controllers
+ b) Interrupt controllers
Some SOC devices contain interrupt controllers that are different
from the standard Open PIC specification. The SOC device nodes for
@@ -1371,508 +1283,7 @@
device_type = "open-pic";
};
-
- e) I2C
-
- Required properties :
-
- - device_type : Should be "i2c"
- - reg : Offset and length of the register set for the device
-
- Recommended properties :
-
- - compatible : Should be "fsl-i2c" for parts compatible with
- Freescale I2C specifications.
- - interrupts : <a b> where a is the interrupt number and b is a
- field that represents an encoding of the sense and level
- information for the interrupt. This should be encoded based on
- the information in section 2) depending on the type of interrupt
- controller you have.
- - interrupt-parent : the phandle for the interrupt controller that
- services interrupts for this device.
- - dfsrr : boolean; if defined, indicates that this I2C device has
- a digital filter sampling rate register
- - fsl5200-clocking : boolean; if defined, indicated that this device
- uses the FSL 5200 clocking mechanism.
-
- Example :
-
- i2c@3000 {
- interrupt-parent = <40000>;
- interrupts = <1b 3>;
- reg = <3000 18>;
- device_type = "i2c";
- compatible = "fsl-i2c";
- dfsrr;
- };
-
-
- f) Freescale SOC USB controllers
-
- The device node for a USB controller that is part of a Freescale
- SOC is as described in the document "Open Firmware Recommended
- Practice : Universal Serial Bus" with the following modifications
- and additions :
-
- Required properties :
- - compatible : Should be "fsl-usb2-mph" for multi port host USB
- controllers, or "fsl-usb2-dr" for dual role USB controllers
- - phy_type : For multi port host USB controllers, should be one of
- "ulpi", or "serial". For dual role USB controllers, should be
- one of "ulpi", "utmi", "utmi_wide", or "serial".
- - reg : Offset and length of the register set for the device
- - port0 : boolean; if defined, indicates port0 is connected for
- fsl-usb2-mph compatible controllers. Either this property or
- "port1" (or both) must be defined for "fsl-usb2-mph" compatible
- controllers.
- - port1 : boolean; if defined, indicates port1 is connected for
- fsl-usb2-mph compatible controllers. Either this property or
- "port0" (or both) must be defined for "fsl-usb2-mph" compatible
- controllers.
- - dr_mode : indicates the working mode for "fsl-usb2-dr" compatible
- controllers. Can be "host", "peripheral", or "otg". Default to
- "host" if not defined for backward compatibility.
-
- Recommended properties :
- - interrupts : <a b> where a is the interrupt number and b is a
- field that represents an encoding of the sense and level
- information for the interrupt. This should be encoded based on
- the information in section 2) depending on the type of interrupt
- controller you have.
- - interrupt-parent : the phandle for the interrupt controller that
- services interrupts for this device.
-
- Example multi port host USB controller device node :
- usb@22000 {
- compatible = "fsl-usb2-mph";
- reg = <22000 1000>;
- #address-cells = <1>;
- #size-cells = <0>;
- interrupt-parent = <700>;
- interrupts = <27 1>;
- phy_type = "ulpi";
- port0;
- port1;
- };
-
- Example dual role USB controller device node :
- usb@23000 {
- compatible = "fsl-usb2-dr";
- reg = <23000 1000>;
- #address-cells = <1>;
- #size-cells = <0>;
- interrupt-parent = <700>;
- interrupts = <26 1>;
- dr_mode = "otg";
- phy = "ulpi";
- };
-
-
- g) Freescale SOC SEC Security Engines
-
- Required properties:
-
- - device_type : Should be "crypto"
- - model : Model of the device. Should be "SEC1" or "SEC2"
- - compatible : Should be "talitos"
- - reg : Offset and length of the register set for the device
- - interrupts : <a b> where a is the interrupt number and b is a
- field that represents an encoding of the sense and level
- information for the interrupt. This should be encoded based on
- the information in section 2) depending on the type of interrupt
- controller you have.
- - interrupt-parent : the phandle for the interrupt controller that
- services interrupts for this device.
- - num-channels : An integer representing the number of channels
- available.
- - channel-fifo-len : An integer representing the number of
- descriptor pointers each channel fetch fifo can hold.
- - exec-units-mask : The bitmask representing what execution units
- (EUs) are available. It's a single 32-bit cell. EU information
- should be encoded following the SEC's Descriptor Header Dword
- EU_SEL0 field documentation, i.e. as follows:
-
- bit 0 = reserved - should be 0
- bit 1 = set if SEC has the ARC4 EU (AFEU)
- bit 2 = set if SEC has the DES/3DES EU (DEU)
- bit 3 = set if SEC has the message digest EU (MDEU)
- bit 4 = set if SEC has the random number generator EU (RNG)
- bit 5 = set if SEC has the public key EU (PKEU)
- bit 6 = set if SEC has the AES EU (AESU)
- bit 7 = set if SEC has the Kasumi EU (KEU)
-
- bits 8 through 31 are reserved for future SEC EUs.
-
- - descriptor-types-mask : The bitmask representing what descriptors
- are available. It's a single 32-bit cell. Descriptor type
- information should be encoded following the SEC's Descriptor
- Header Dword DESC_TYPE field documentation, i.e. as follows:
-
- bit 0 = set if SEC supports the aesu_ctr_nonsnoop desc. type
- bit 1 = set if SEC supports the ipsec_esp descriptor type
- bit 2 = set if SEC supports the common_nonsnoop desc. type
- bit 3 = set if SEC supports the 802.11i AES ccmp desc. type
- bit 4 = set if SEC supports the hmac_snoop_no_afeu desc. type
- bit 5 = set if SEC supports the srtp descriptor type
- bit 6 = set if SEC supports the non_hmac_snoop_no_afeu desc.type
- bit 7 = set if SEC supports the pkeu_assemble descriptor type
- bit 8 = set if SEC supports the aesu_key_expand_output desc.type
- bit 9 = set if SEC supports the pkeu_ptmul descriptor type
- bit 10 = set if SEC supports the common_nonsnoop_afeu desc. type
- bit 11 = set if SEC supports the pkeu_ptadd_dbl descriptor type
-
- ..and so on and so forth.
-
- Example:
-
- /* MPC8548E */
- crypto@30000 {
- device_type = "crypto";
- model = "SEC2";
- compatible = "talitos";
- reg = <30000 10000>;
- interrupts = <1d 3>;
- interrupt-parent = <40000>;
- num-channels = <4>;
- channel-fifo-len = <18>;
- exec-units-mask = <000000fe>;
- descriptor-types-mask = <012b0ebf>;
- };
-
- h) Board Control and Status (BCSR)
-
- Required properties:
-
- - device_type : Should be "board-control"
- - reg : Offset and length of the register set for the device
-
- Example:
-
- bcsr@f8000000 {
- device_type = "board-control";
- reg = <f8000000 8000>;
- };
-
- i) Freescale QUICC Engine module (QE)
- This represents qe module that is installed on PowerQUICC II Pro.
-
- NOTE: This is an interim binding; it should be updated to fit
- in with the CPM binding later in this document.
-
- Basically, it is a bus of devices, that could act more or less
- as a complete entity (UCC, USB etc ). All of them should be siblings on
- the "root" qe node, using the common properties from there.
- The description below applies to the qe of MPC8360 and
- more nodes and properties would be extended in the future.
-
- i) Root QE device
-
- Required properties:
- - compatible : should be "fsl,qe";
- - model : precise model of the QE, Can be "QE", "CPM", or "CPM2"
- - reg : offset and length of the device registers.
- - bus-frequency : the clock frequency for QUICC Engine.
-
- Recommended properties
- - brg-frequency : the internal clock source frequency for baud-rate
- generators in Hz.
-
- Example:
- qe@e0100000 {
- #address-cells = <1>;
- #size-cells = <1>;
- #interrupt-cells = <2>;
- compatible = "fsl,qe";
- ranges = <0 e0100000 00100000>;
- reg = <e0100000 480>;
- brg-frequency = <0>;
- bus-frequency = <179A7B00>;
- }
-
-
- ii) SPI (Serial Peripheral Interface)
-
- Required properties:
- - cell-index : SPI controller index.
- - compatible : should be "fsl,spi".
- - mode : the SPI operation mode, it can be "cpu" or "cpu-qe".
- - reg : Offset and length of the register set for the device
- - interrupts : <a b> where a is the interrupt number and b is a
- field that represents an encoding of the sense and level
- information for the interrupt. This should be encoded based on
- the information in section 2) depending on the type of interrupt
- controller you have.
- - interrupt-parent : the phandle for the interrupt controller that
- services interrupts for this device.
-
- Example:
- spi@4c0 {
- cell-index = <0>;
- compatible = "fsl,spi";
- reg = <4c0 40>;
- interrupts = <82 0>;
- interrupt-parent = <700>;
- mode = "cpu";
- };
-
-
- iii) USB (Universal Serial Bus Controller)
-
- Required properties:
- - compatible : could be "qe_udc" or "fhci-hcd".
- - mode : the could be "host" or "slave".
- - reg : Offset and length of the register set for the device
- - interrupts : <a b> where a is the interrupt number and b is a
- field that represents an encoding of the sense and level
- information for the interrupt. This should be encoded based on
- the information in section 2) depending on the type of interrupt
- controller you have.
- - interrupt-parent : the phandle for the interrupt controller that
- services interrupts for this device.
-
- Example(slave):
- usb@6c0 {
- compatible = "qe_udc";
- reg = <6c0 40>;
- interrupts = <8b 0>;
- interrupt-parent = <700>;
- mode = "slave";
- };
-
-
- iv) UCC (Unified Communications Controllers)
-
- Required properties:
- - device_type : should be "network", "hldc", "uart", "transparent"
- "bisync", "atm", or "serial".
- - compatible : could be "ucc_geth" or "fsl_atm" and so on.
- - cell-index : the ucc number(1-8), corresponding to UCCx in UM.
- - reg : Offset and length of the register set for the device
- - interrupts : <a b> where a is the interrupt number and b is a
- field that represents an encoding of the sense and level
- information for the interrupt. This should be encoded based on
- the information in section 2) depending on the type of interrupt
- controller you have.
- - interrupt-parent : the phandle for the interrupt controller that
- services interrupts for this device.
- - pio-handle : The phandle for the Parallel I/O port configuration.
- - port-number : for UART drivers, the port number to use, between 0 and 3.
- This usually corresponds to the /dev/ttyQE device, e.g. <0> = /dev/ttyQE0.
- The port number is added to the minor number of the device. Unlike the
- CPM UART driver, the port-number is required for the QE UART driver.
- - soft-uart : for UART drivers, if specified this means the QE UART device
- driver should use "Soft-UART" mode, which is needed on some SOCs that have
- broken UART hardware. Soft-UART is provided via a microcode upload.
- - rx-clock-name: the UCC receive clock source
- "none": clock source is disabled
- "brg1" through "brg16": clock source is BRG1-BRG16, respectively
- "clk1" through "clk24": clock source is CLK1-CLK24, respectively
- - tx-clock-name: the UCC transmit clock source
- "none": clock source is disabled
- "brg1" through "brg16": clock source is BRG1-BRG16, respectively
- "clk1" through "clk24": clock source is CLK1-CLK24, respectively
- The following two properties are deprecated. rx-clock has been replaced
- with rx-clock-name, and tx-clock has been replaced with tx-clock-name.
- Drivers that currently use the deprecated properties should continue to
- do so, in order to support older device trees, but they should be updated
- to check for the new properties first.
- - rx-clock : represents the UCC receive clock source.
- 0x00 : clock source is disabled;
- 0x1~0x10 : clock source is BRG1~BRG16 respectively;
- 0x11~0x28: clock source is QE_CLK1~QE_CLK24 respectively.
- - tx-clock: represents the UCC transmit clock source;
- 0x00 : clock source is disabled;
- 0x1~0x10 : clock source is BRG1~BRG16 respectively;
- 0x11~0x28: clock source is QE_CLK1~QE_CLK24 respectively.
-
- Required properties for network device_type:
- - mac-address : list of bytes representing the ethernet address.
- - phy-handle : The phandle for the PHY connected to this controller.
-
- Recommended properties:
- - phy-connection-type : a string naming the controller/PHY interface type,
- i.e., "mii" (default), "rmii", "gmii", "rgmii", "rgmii-id" (Internal
- Delay), "rgmii-txid" (delay on TX only), "rgmii-rxid" (delay on RX only),
- "tbi", or "rtbi".
-
- Example:
- ucc@2000 {
- device_type = "network";
- compatible = "ucc_geth";
- cell-index = <1>;
- reg = <2000 200>;
- interrupts = <a0 0>;
- interrupt-parent = <700>;
- mac-address = [ 00 04 9f 00 23 23 ];
- rx-clock = "none";
- tx-clock = "clk9";
- phy-handle = <212000>;
- phy-connection-type = "gmii";
- pio-handle = <140001>;
- };
-
-
- v) Parallel I/O Ports
-
- This node configures Parallel I/O ports for CPUs with QE support.
- The node should reside in the "soc" node of the tree. For each
- device that using parallel I/O ports, a child node should be created.
- See the definition of the Pin configuration nodes below for more
- information.
-
- Required properties:
- - device_type : should be "par_io".
- - reg : offset to the register set and its length.
- - num-ports : number of Parallel I/O ports
-
- Example:
- par_io@1400 {
- reg = <1400 100>;
- #address-cells = <1>;
- #size-cells = <0>;
- device_type = "par_io";
- num-ports = <7>;
- ucc_pin@01 {
- ......
- };
-
- Note that "par_io" nodes are obsolete, and should not be used for
- the new device trees. Instead, each Par I/O bank should be represented
- via its own gpio-controller node:
-
- Required properties:
- - #gpio-cells : should be "2".
- - compatible : should be "fsl,<chip>-qe-pario-bank",
- "fsl,mpc8323-qe-pario-bank".
- - reg : offset to the register set and its length.
- - gpio-controller : node to identify gpio controllers.
-
- Example:
- qe_pio_a: gpio-controller@1400 {
- #gpio-cells = <2>;
- compatible = "fsl,mpc8360-qe-pario-bank",
- "fsl,mpc8323-qe-pario-bank";
- reg = <0x1400 0x18>;
- gpio-controller;
- };
-
- qe_pio_e: gpio-controller@1460 {
- #gpio-cells = <2>;
- compatible = "fsl,mpc8360-qe-pario-bank",
- "fsl,mpc8323-qe-pario-bank";
- reg = <0x1460 0x18>;
- gpio-controller;
- };
-
- vi) Pin configuration nodes
-
- Required properties:
- - linux,phandle : phandle of this node; likely referenced by a QE
- device.
- - pio-map : array of pin configurations. Each pin is defined by 6
- integers. The six numbers are respectively: port, pin, dir,
- open_drain, assignment, has_irq.
- - port : port number of the pin; 0-6 represent port A-G in UM.
- - pin : pin number in the port.
- - dir : direction of the pin, should encode as follows:
-
- 0 = The pin is disabled
- 1 = The pin is an output
- 2 = The pin is an input
- 3 = The pin is I/O
-
- - open_drain : indicates the pin is normal or wired-OR:
-
- 0 = The pin is actively driven as an output
- 1 = The pin is an open-drain driver. As an output, the pin is
- driven active-low, otherwise it is three-stated.
-
- - assignment : function number of the pin according to the Pin Assignment
- tables in User Manual. Each pin can have up to 4 possible functions in
- QE and two options for CPM.
- - has_irq : indicates if the pin is used as source of external
- interrupts.
-
- Example:
- ucc_pin@01 {
- linux,phandle = <140001>;
- pio-map = <
- /* port pin dir open_drain assignment has_irq */
- 0 3 1 0 1 0 /* TxD0 */
- 0 4 1 0 1 0 /* TxD1 */
- 0 5 1 0 1 0 /* TxD2 */
- 0 6 1 0 1 0 /* TxD3 */
- 1 6 1 0 3 0 /* TxD4 */
- 1 7 1 0 1 0 /* TxD5 */
- 1 9 1 0 2 0 /* TxD6 */
- 1 a 1 0 2 0 /* TxD7 */
- 0 9 2 0 1 0 /* RxD0 */
- 0 a 2 0 1 0 /* RxD1 */
- 0 b 2 0 1 0 /* RxD2 */
- 0 c 2 0 1 0 /* RxD3 */
- 0 d 2 0 1 0 /* RxD4 */
- 1 1 2 0 2 0 /* RxD5 */
- 1 0 2 0 2 0 /* RxD6 */
- 1 4 2 0 2 0 /* RxD7 */
- 0 7 1 0 1 0 /* TX_EN */
- 0 8 1 0 1 0 /* TX_ER */
- 0 f 2 0 1 0 /* RX_DV */
- 0 10 2 0 1 0 /* RX_ER */
- 0 0 2 0 1 0 /* RX_CLK */
- 2 9 1 0 3 0 /* GTX_CLK - CLK10 */
- 2 8 2 0 1 0>; /* GTX125 - CLK9 */
- };
-
- vii) Multi-User RAM (MURAM)
-
- Required properties:
- - compatible : should be "fsl,qe-muram", "fsl,cpm-muram".
- - mode : the could be "host" or "slave".
- - ranges : Should be defined as specified in 1) to describe the
- translation of MURAM addresses.
- - data-only : sub-node which defines the address area under MURAM
- bus that can be allocated as data/parameter
-
- Example:
-
- muram@10000 {
- compatible = "fsl,qe-muram", "fsl,cpm-muram";
- ranges = <0 00010000 0000c000>;
-
- data-only@0{
- compatible = "fsl,qe-muram-data",
- "fsl,cpm-muram-data";
- reg = <0 c000>;
- };
- };
-
- viii) Uploaded QE firmware
-
- If a new firwmare has been uploaded to the QE (usually by the
- boot loader), then a 'firmware' child node should be added to the QE
- node. This node provides information on the uploaded firmware that
- device drivers may need.
-
- Required properties:
- - id: The string name of the firmware. This is taken from the 'id'
- member of the qe_firmware structure of the uploaded firmware.
- Device drivers can search this string to determine if the
- firmware they want is already present.
- - extended-modes: The Extended Modes bitfield, taken from the
- firmware binary. It is a 64-bit number represented
- as an array of two 32-bit numbers.
- - virtual-traps: The virtual traps, taken from the firmware binary.
- It is an array of 8 32-bit numbers.
-
- Example:
-
- firmware {
- id = "Soft-UART";
- extended-modes = <0 0>;
- virtual-traps = <0 0 0 0 0 0 0 0>;
- }
-
- j) CFI or JEDEC memory-mapped NOR flash
+ c) CFI or JEDEC memory-mapped NOR flash
Flash chips (Memory Technology Devices) are often used for solid state
file systems on embedded devices.
@@ -1936,310 +1347,7 @@
};
};
- k) Global Utilities Block
-
- The global utilities block controls power management, I/O device
- enabling, power-on-reset configuration monitoring, general-purpose
- I/O signal configuration, alternate function selection for multiplexed
- signals, and clock control.
-
- Required properties:
-
- - compatible : Should define the compatible device type for
- global-utilities.
- - reg : Offset and length of the register set for the device.
-
- Recommended properties:
-
- - fsl,has-rstcr : Indicates that the global utilities register set
- contains a functioning "reset control register" (i.e. the board
- is wired to reset upon setting the HRESET_REQ bit in this register).
-
- Example:
-
- global-utilities@e0000 { /* global utilities block */
- compatible = "fsl,mpc8548-guts";
- reg = <e0000 1000>;
- fsl,has-rstcr;
- };
-
- l) Freescale Communications Processor Module
-
- NOTE: This is an interim binding, and will likely change slightly,
- as more devices are supported. The QE bindings especially are
- incomplete.
-
- i) Root CPM node
-
- Properties:
- - compatible : "fsl,cpm1", "fsl,cpm2", or "fsl,qe".
- - reg : A 48-byte region beginning with CPCR.
-
- Example:
- cpm@119c0 {
- #address-cells = <1>;
- #size-cells = <1>;
- #interrupt-cells = <2>;
- compatible = "fsl,mpc8272-cpm", "fsl,cpm2";
- reg = <119c0 30>;
- }
-
- ii) Properties common to mulitple CPM/QE devices
-
- - fsl,cpm-command : This value is ORed with the opcode and command flag
- to specify the device on which a CPM command operates.
-
- - fsl,cpm-brg : Indicates which baud rate generator the device
- is associated with. If absent, an unused BRG
- should be dynamically allocated. If zero, the
- device uses an external clock rather than a BRG.
-
- - reg : Unless otherwise specified, the first resource represents the
- scc/fcc/ucc registers, and the second represents the device's
- parameter RAM region (if it has one).
-
- iii) Serial
-
- Currently defined compatibles:
- - fsl,cpm1-smc-uart
- - fsl,cpm2-smc-uart
- - fsl,cpm1-scc-uart
- - fsl,cpm2-scc-uart
- - fsl,qe-uart
-
- Example:
-
- serial@11a00 {
- device_type = "serial";
- compatible = "fsl,mpc8272-scc-uart",
- "fsl,cpm2-scc-uart";
- reg = <11a00 20 8000 100>;
- interrupts = <28 8>;
- interrupt-parent = <&PIC>;
- fsl,cpm-brg = <1>;
- fsl,cpm-command = <00800000>;
- };
-
- iii) Network
-
- Currently defined compatibles:
- - fsl,cpm1-scc-enet
- - fsl,cpm2-scc-enet
- - fsl,cpm1-fec-enet
- - fsl,cpm2-fcc-enet (third resource is GFEMR)
- - fsl,qe-enet
-
- Example:
-
- ethernet@11300 {
- device_type = "network";
- compatible = "fsl,mpc8272-fcc-enet",
- "fsl,cpm2-fcc-enet";
- reg = <11300 20 8400 100 11390 1>;
- local-mac-address = [ 00 00 00 00 00 00 ];
- interrupts = <20 8>;
- interrupt-parent = <&PIC>;
- phy-handle = <&PHY0>;
- fsl,cpm-command = <12000300>;
- };
-
- iv) MDIO
-
- Currently defined compatibles:
- fsl,pq1-fec-mdio (reg is same as first resource of FEC device)
- fsl,cpm2-mdio-bitbang (reg is port C registers)
-
- Properties for fsl,cpm2-mdio-bitbang:
- fsl,mdio-pin : pin of port C controlling mdio data
- fsl,mdc-pin : pin of port C controlling mdio clock
-
- Example:
-
- mdio@10d40 {
- device_type = "mdio";
- compatible = "fsl,mpc8272ads-mdio-bitbang",
- "fsl,mpc8272-mdio-bitbang",
- "fsl,cpm2-mdio-bitbang";
- reg = <10d40 14>;
- #address-cells = <1>;
- #size-cells = <0>;
- fsl,mdio-pin = <12>;
- fsl,mdc-pin = <13>;
- };
-
- v) Baud Rate Generators
-
- Currently defined compatibles:
- fsl,cpm-brg
- fsl,cpm1-brg
- fsl,cpm2-brg
-
- Properties:
- - reg : There may be an arbitrary number of reg resources; BRG
- numbers are assigned to these in order.
- - clock-frequency : Specifies the base frequency driving
- the BRG.
-
- Example:
-
- brg@119f0 {
- compatible = "fsl,mpc8272-brg",
- "fsl,cpm2-brg",
- "fsl,cpm-brg";
- reg = <119f0 10 115f0 10>;
- clock-frequency = <d#25000000>;
- };
-
- vi) Interrupt Controllers
-
- Currently defined compatibles:
- - fsl,cpm1-pic
- - only one interrupt cell
- - fsl,pq1-pic
- - fsl,cpm2-pic
- - second interrupt cell is level/sense:
- - 2 is falling edge
- - 8 is active low
-
- Example:
-
- interrupt-controller@10c00 {
- #interrupt-cells = <2>;
- interrupt-controller;
- reg = <10c00 80>;
- compatible = "mpc8272-pic", "fsl,cpm2-pic";
- };
-
- vii) USB (Universal Serial Bus Controller)
-
- Properties:
- - compatible : "fsl,cpm1-usb", "fsl,cpm2-usb", "fsl,qe-usb"
-
- Example:
- usb@11bc0 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,cpm2-usb";
- reg = <11b60 18 8b00 100>;
- interrupts = <b 8>;
- interrupt-parent = <&PIC>;
- fsl,cpm-command = <2e600000>;
- };
-
- viii) Multi-User RAM (MURAM)
-
- The multi-user/dual-ported RAM is expressed as a bus under the CPM node.
-
- Ranges must be set up subject to the following restrictions:
-
- - Children's reg nodes must be offsets from the start of all muram, even
- if the user-data area does not begin at zero.
- - If multiple range entries are used, the difference between the parent
- address and the child address must be the same in all, so that a single
- mapping can cover them all while maintaining the ability to determine
- CPM-side offsets with pointer subtraction. It is recommended that
- multiple range entries not be used.
- - A child address of zero must be translatable, even if no reg resources
- contain it.
-
- A child "data" node must exist, compatible with "fsl,cpm-muram-data", to
- indicate the portion of muram that is usable by the OS for arbitrary
- purposes. The data node may have an arbitrary number of reg resources,
- all of which contribute to the allocatable muram pool.
-
- Example, based on mpc8272:
-
- muram@0 {
- #address-cells = <1>;
- #size-cells = <1>;
- ranges = <0 0 10000>;
-
- data@0 {
- compatible = "fsl,cpm-muram-data";
- reg = <0 2000 9800 800>;
- };
- };
-
- x) I2C
-
- The I2C controller is expressed as a bus under the CPM node.
-
- Properties:
- - compatible : "fsl,cpm1-i2c", "fsl,cpm2-i2c"
- - reg : On CPM2 devices, the second resource doesn't specify the I2C
- Parameter RAM itself, but the I2C_BASE field of the CPM2 Parameter RAM
- (typically 0x8afc 0x2).
- - #address-cells : Should be one. The cell is the i2c device address with
- the r/w bit set to zero.
- - #size-cells : Should be zero.
- - clock-frequency : Can be used to set the i2c clock frequency. If
- unspecified, a default frequency of 60kHz is being used.
- The following two properties are deprecated. They are only used by legacy
- i2c drivers to find the bus to probe:
- - linux,i2c-index : Can be used to hard code an i2c bus number. By default,
- the bus number is dynamically assigned by the i2c core.
- - linux,i2c-class : Can be used to override the i2c class. The class is used
- by legacy i2c device drivers to find a bus in a specific context like
- system management, video or sound. By default, I2C_CLASS_HWMON (1) is
- being used. The definition of the classes can be found in
- include/i2c/i2c.h
-
- Example, based on mpc823:
-
- i2c@860 {
- compatible = "fsl,mpc823-i2c",
- "fsl,cpm1-i2c";
- reg = <0x860 0x20 0x3c80 0x30>;
- interrupts = <16>;
- interrupt-parent = <&CPM_PIC>;
- fsl,cpm-command = <0x10>;
- #address-cells = <1>;
- #size-cells = <0>;
-
- rtc@68 {
- compatible = "dallas,ds1307";
- reg = <0x68>;
- };
- };
-
- m) Chipselect/Local Bus
-
- Properties:
- - name : Should be localbus
- - #address-cells : Should be either two or three. The first cell is the
- chipselect number, and the remaining cells are the
- offset into the chipselect.
- - #size-cells : Either one or two, depending on how large each chipselect
- can be.
- - ranges : Each range corresponds to a single chipselect, and cover
- the entire access window as configured.
-
- Example:
- localbus@f0010100 {
- compatible = "fsl,mpc8272-localbus",
- "fsl,pq2-localbus";
- #address-cells = <2>;
- #size-cells = <1>;
- reg = <f0010100 40>;
-
- ranges = <0 0 fe000000 02000000
- 1 0 f4500000 00008000>;
-
- flash@0,0 {
- compatible = "jedec-flash";
- reg = <0 0 2000000>;
- bank-width = <4>;
- device-width = <1>;
- };
-
- board-control@1,0 {
- reg = <1 0 20>;
- compatible = "fsl,mpc8272ads-bcsr";
- };
- };
-
-
- n) 4xx/Axon EMAC ethernet nodes
+ d) 4xx/Axon EMAC ethernet nodes
The EMAC ethernet controller in IBM and AMCC 4xx chips, and also
the Axon bridge. To operate this needs to interact with a ths
@@ -2387,7 +1495,7 @@
available.
For Axon: 0x0000012a
- o) Xilinx IP cores
+ e) Xilinx IP cores
The Xilinx EDK toolchain ships with a set of IP cores (devices) for use
in Xilinx Spartan and Virtex FPGAs. The devices cover the whole range
@@ -2681,206 +1789,7 @@
- reg-offset : A value of 3 is required
- reg-shift : A value of 2 is required
-
- p) Freescale Synchronous Serial Interface
-
- The SSI is a serial device that communicates with audio codecs. It can
- be programmed in AC97, I2S, left-justified, or right-justified modes.
-
- Required properties:
- - compatible : compatible list, containing "fsl,ssi"
- - cell-index : the SSI, <0> = SSI1, <1> = SSI2, and so on
- - reg : offset and length of the register set for the device
- - interrupts : <a b> where a is the interrupt number and b is a
- field that represents an encoding of the sense and
- level information for the interrupt. This should be
- encoded based on the information in section 2)
- depending on the type of interrupt controller you
- have.
- - interrupt-parent : the phandle for the interrupt controller that
- services interrupts for this device.
- - fsl,mode : the operating mode for the SSI interface
- "i2s-slave" - I2S mode, SSI is clock slave
- "i2s-master" - I2S mode, SSI is clock master
- "lj-slave" - left-justified mode, SSI is clock slave
- "lj-master" - l.j. mode, SSI is clock master
- "rj-slave" - right-justified mode, SSI is clock slave
- "rj-master" - r.j., SSI is clock master
- "ac97-slave" - AC97 mode, SSI is clock slave
- "ac97-master" - AC97 mode, SSI is clock master
-
- Optional properties:
- - codec-handle : phandle to a 'codec' node that defines an audio
- codec connected to this SSI. This node is typically
- a child of an I2C or other control node.
-
- Child 'codec' node required properties:
- - compatible : compatible list, contains the name of the codec
-
- Child 'codec' node optional properties:
- - clock-frequency : The frequency of the input clock, which typically
- comes from an on-board dedicated oscillator.
-
- * Freescale 83xx DMA Controller
-
- Freescale PowerPC 83xx have on chip general purpose DMA controllers.
-
- Required properties:
-
- - compatible : compatible list, contains 2 entries, first is
- "fsl,CHIP-dma", where CHIP is the processor
- (mpc8349, mpc8360, etc.) and the second is
- "fsl,elo-dma"
- - reg : <registers mapping for DMA general status reg>
- - ranges : Should be defined as specified in 1) to describe the
- DMA controller channels.
- - cell-index : controller index. 0 for controller @ 0x8100
- - interrupts : <interrupt mapping for DMA IRQ>
- - interrupt-parent : optional, if needed for interrupt mapping
-
-
- - DMA channel nodes:
- - compatible : compatible list, contains 2 entries, first is
- "fsl,CHIP-dma-channel", where CHIP is the processor
- (mpc8349, mpc8350, etc.) and the second is
- "fsl,elo-dma-channel"
- - reg : <registers mapping for channel>
- - cell-index : dma channel index starts at 0.
-
- Optional properties:
- - interrupts : <interrupt mapping for DMA channel IRQ>
- (on 83xx this is expected to be identical to
- the interrupts property of the parent node)
- - interrupt-parent : optional, if needed for interrupt mapping
-
- Example:
- dma@82a8 {
- #address-cells = <1>;
- #size-cells = <1>;
- compatible = "fsl,mpc8349-dma", "fsl,elo-dma";
- reg = <82a8 4>;
- ranges = <0 8100 1a4>;
- interrupt-parent = <&ipic>;
- interrupts = <47 8>;
- cell-index = <0>;
- dma-channel@0 {
- compatible = "fsl,mpc8349-dma-channel", "fsl,elo-dma-channel";
- cell-index = <0>;
- reg = <0 80>;
- };
- dma-channel@80 {
- compatible = "fsl,mpc8349-dma-channel", "fsl,elo-dma-channel";
- cell-index = <1>;
- reg = <80 80>;
- };
- dma-channel@100 {
- compatible = "fsl,mpc8349-dma-channel", "fsl,elo-dma-channel";
- cell-index = <2>;
- reg = <100 80>;
- };
- dma-channel@180 {
- compatible = "fsl,mpc8349-dma-channel", "fsl,elo-dma-channel";
- cell-index = <3>;
- reg = <180 80>;
- };
- };
-
- * Freescale 85xx/86xx DMA Controller
-
- Freescale PowerPC 85xx/86xx have on chip general purpose DMA controllers.
-
- Required properties:
-
- - compatible : compatible list, contains 2 entries, first is
- "fsl,CHIP-dma", where CHIP is the processor
- (mpc8540, mpc8540, etc.) and the second is
- "fsl,eloplus-dma"
- - reg : <registers mapping for DMA general status reg>
- - cell-index : controller index. 0 for controller @ 0x21000,
- 1 for controller @ 0xc000
- - ranges : Should be defined as specified in 1) to describe the
- DMA controller channels.
-
- - DMA channel nodes:
- - compatible : compatible list, contains 2 entries, first is
- "fsl,CHIP-dma-channel", where CHIP is the processor
- (mpc8540, mpc8560, etc.) and the second is
- "fsl,eloplus-dma-channel"
- - cell-index : dma channel index starts at 0.
- - reg : <registers mapping for channel>
- - interrupts : <interrupt mapping for DMA channel IRQ>
- - interrupt-parent : optional, if needed for interrupt mapping
-
- Example:
- dma@21300 {
- #address-cells = <1>;
- #size-cells = <1>;
- compatible = "fsl,mpc8540-dma", "fsl,eloplus-dma";
- reg = <21300 4>;
- ranges = <0 21100 200>;
- cell-index = <0>;
- dma-channel@0 {
- compatible = "fsl,mpc8540-dma-channel", "fsl,eloplus-dma-channel";
- reg = <0 80>;
- cell-index = <0>;
- interrupt-parent = <&mpic>;
- interrupts = <14 2>;
- };
- dma-channel@80 {
- compatible = "fsl,mpc8540-dma-channel", "fsl,eloplus-dma-channel";
- reg = <80 80>;
- cell-index = <1>;
- interrupt-parent = <&mpic>;
- interrupts = <15 2>;
- };
- dma-channel@100 {
- compatible = "fsl,mpc8540-dma-channel", "fsl,eloplus-dma-channel";
- reg = <100 80>;
- cell-index = <2>;
- interrupt-parent = <&mpic>;
- interrupts = <16 2>;
- };
- dma-channel@180 {
- compatible = "fsl,mpc8540-dma-channel", "fsl,eloplus-dma-channel";
- reg = <180 80>;
- cell-index = <3>;
- interrupt-parent = <&mpic>;
- interrupts = <17 2>;
- };
- };
-
- * Freescale 8xxx/3.0 Gb/s SATA nodes
-
- SATA nodes are defined to describe on-chip Serial ATA controllers.
- Each SATA port should have its own node.
-
- Required properties:
- - compatible : compatible list, contains 2 entries, first is
- "fsl,CHIP-sata", where CHIP is the processor
- (mpc8315, mpc8379, etc.) and the second is
- "fsl,pq-sata"
- - interrupts : <interrupt mapping for SATA IRQ>
- - cell-index : controller index.
- 1 for controller @ 0x18000
- 2 for controller @ 0x19000
- 3 for controller @ 0x1a000
- 4 for controller @ 0x1b000
-
- Optional properties:
- - interrupt-parent : optional, if needed for interrupt mapping
- - reg : <registers mapping>
-
- Example:
-
- sata@18000 {
- compatible = "fsl,mpc8379-sata", "fsl,pq-sata";
- reg = <0x18000 0x1000>;
- cell-index = <1>;
- interrupts = <2c 8>;
- interrupt-parent = < &ipic >;
- };
-
- q) USB EHCI controllers
+ f) USB EHCI controllers
Required properties:
- compatible : should be "usb-ehci".
@@ -2906,109 +1815,6 @@
big-endian;
};
- r) Freescale Display Interface Unit
-
- The Freescale DIU is a LCD controller, with proper hardware, it can also
- drive DVI monitors.
-
- Required properties:
- - compatible : should be "fsl-diu".
- - reg : should contain at least address and length of the DIU register
- set.
- - Interrupts : one DIU interrupt should be describe here.
-
- Example (MPC8610HPCD)
- display@2c000 {
- compatible = "fsl,diu";
- reg = <0x2c000 100>;
- interrupts = <72 2>;
- interrupt-parent = <&mpic>;
- };
-
- s) Freescale on board FPGA
-
- This is the memory-mapped registers for on board FPGA.
-
- Required properities:
- - compatible : should be "fsl,fpga-pixis".
- - reg : should contain the address and the lenght of the FPPGA register
- set.
-
- Example (MPC8610HPCD)
- board-control@e8000000 {
- compatible = "fsl,fpga-pixis";
- reg = <0xe8000000 32>;
- };
-
- t) Freescale MSI interrupt controller
-
- Reguired properities:
- - compatible : compatible list, contains 2 entries,
- first is "fsl,CHIP-msi", where CHIP is the processor(mpc8610, mpc8572,
- etc.) and the second is "fsl,mpic-msi" or "fsl,ipic-msi" depending on
- the parent type.
- - reg : should contain the address and the length of the shared message
- interrupt register set.
- - msi-available-ranges: use <start count> style section to define which
- msi interrupt can be used in the 256 msi interrupts. This property is
- optional, without this, all the 256 MSI interrupts can be used.
- - interrupts : each one of the interrupts here is one entry per 32 MSIs,
- and routed to the host interrupt controller. the interrupts should
- be set as edge sensitive.
- - interrupt-parent: the phandle for the interrupt controller
- that services interrupts for this device. for 83xx cpu, the interrupts
- are routed to IPIC, and for 85xx/86xx cpu the interrupts are routed
- to MPIC.
-
- Example
- msi@41600 {
- compatible = "fsl,mpc8610-msi", "fsl,mpic-msi";
- reg = <0x41600 0x80>;
- msi-available-ranges = <0 0x100>;
- interrupts = <
- 0xe0 0
- 0xe1 0
- 0xe2 0
- 0xe3 0
- 0xe4 0
- 0xe5 0
- 0xe6 0
- 0xe7 0>;
- interrupt-parent = <&mpic>;
- };
-
- u) Freescale General-purpose Timers Module
-
- Required properties:
- - compatible : should be
- "fsl,<chip>-gtm", "fsl,gtm" for SOC GTMs
- "fsl,<chip>-qe-gtm", "fsl,qe-gtm", "fsl,gtm" for QE GTMs
- "fsl,<chip>-cpm2-gtm", "fsl,cpm2-gtm", "fsl,gtm" for CPM2 GTMs
- - reg : should contain gtm registers location and length (0x40).
- - interrupts : should contain four interrupts.
- - interrupt-parent : interrupt source phandle.
- - clock-frequency : specifies the frequency driving the timer.
-
- Example:
-
- timer@500 {
- compatible = "fsl,mpc8360-gtm", "fsl,gtm";
- reg = <0x500 0x40>;
- interrupts = <90 8 78 8 84 8 72 8>;
- interrupt-parent = <&ipic>;
- /* filled by u-boot */
- clock-frequency = <0>;
- };
-
- timer@440 {
- compatible = "fsl,mpc8360-qe-gtm", "fsl,qe-gtm", "fsl,gtm";
- reg = <0x440 0x40>;
- interrupts = <12 13 14 15>;
- interrupt-parent = <&qeic>;
- /* filled by u-boot */
- clock-frequency = <0>;
- };
-
VII - Marvell Discovery mv64[345]6x System Controller chips
===========================================================
diff --git a/Documentation/powerpc/dts-bindings/fsl/board.txt b/Documentation/powerpc/dts-bindings/fsl/board.txt
new file mode 100644
index 0000000..74ae6f1
--- /dev/null
+++ b/Documentation/powerpc/dts-bindings/fsl/board.txt
@@ -0,0 +1,29 @@
+* Board Control and Status (BCSR)
+
+Required properties:
+
+ - device_type : Should be "board-control"
+ - reg : Offset and length of the register set for the device
+
+Example:
+
+ bcsr@f8000000 {
+ device_type = "board-control";
+ reg = <f8000000 8000>;
+ };
+
+* Freescale on board FPGA
+
+This is the memory-mapped registers for on board FPGA.
+
+Required properities:
+- compatible : should be "fsl,fpga-pixis".
+- reg : should contain the address and the lenght of the FPPGA register
+ set.
+
+Example (MPC8610HPCD):
+
+ board-control@e8000000 {
+ compatible = "fsl,fpga-pixis";
+ reg = <0xe8000000 32>;
+ };
diff --git a/Documentation/powerpc/dts-bindings/fsl/cpm_qe/cpm.txt b/Documentation/powerpc/dts-bindings/fsl/cpm_qe/cpm.txt
new file mode 100644
index 0000000..088fc47
--- /dev/null
+++ b/Documentation/powerpc/dts-bindings/fsl/cpm_qe/cpm.txt
@@ -0,0 +1,67 @@
+* Freescale Communications Processor Module
+
+NOTE: This is an interim binding, and will likely change slightly,
+as more devices are supported. The QE bindings especially are
+incomplete.
+
+* Root CPM node
+
+Properties:
+- compatible : "fsl,cpm1", "fsl,cpm2", or "fsl,qe".
+- reg : A 48-byte region beginning with CPCR.
+
+Example:
+ cpm@119c0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ #interrupt-cells = <2>;
+ compatible = "fsl,mpc8272-cpm", "fsl,cpm2";
+ reg = <119c0 30>;
+ }
+
+* Properties common to mulitple CPM/QE devices
+
+- fsl,cpm-command : This value is ORed with the opcode and command flag
+ to specify the device on which a CPM command operates.
+
+- fsl,cpm-brg : Indicates which baud rate generator the device
+ is associated with. If absent, an unused BRG
+ should be dynamically allocated. If zero, the
+ device uses an external clock rather than a BRG.
+
+- reg : Unless otherwise specified, the first resource represents the
+ scc/fcc/ucc registers, and the second represents the device's
+ parameter RAM region (if it has one).
+
+* Multi-User RAM (MURAM)
+
+The multi-user/dual-ported RAM is expressed as a bus under the CPM node.
+
+Ranges must be set up subject to the following restrictions:
+
+- Children's reg nodes must be offsets from the start of all muram, even
+ if the user-data area does not begin at zero.
+- If multiple range entries are used, the difference between the parent
+ address and the child address must be the same in all, so that a single
+ mapping can cover them all while maintaining the ability to determine
+ CPM-side offsets with pointer subtraction. It is recommended that
+ multiple range entries not be used.
+- A child address of zero must be translatable, even if no reg resources
+ contain it.
+
+A child "data" node must exist, compatible with "fsl,cpm-muram-data", to
+indicate the portion of muram that is usable by the OS for arbitrary
+purposes. The data node may have an arbitrary number of reg resources,
+all of which contribute to the allocatable muram pool.
+
+Example, based on mpc8272:
+ muram@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0 10000>;
+
+ data@0 {
+ compatible = "fsl,cpm-muram-data";
+ reg = <0 2000 9800 800>;
+ };
+ };
diff --git a/Documentation/powerpc/dts-bindings/fsl/cpm_qe/cpm/brg.txt b/Documentation/powerpc/dts-bindings/fsl/cpm_qe/cpm/brg.txt
new file mode 100644
index 0000000..4c7d45e
--- /dev/null
+++ b/Documentation/powerpc/dts-bindings/fsl/cpm_qe/cpm/brg.txt
@@ -0,0 +1,21 @@
+* Baud Rate Generators
+
+Currently defined compatibles:
+fsl,cpm-brg
+fsl,cpm1-brg
+fsl,cpm2-brg
+
+Properties:
+- reg : There may be an arbitrary number of reg resources; BRG
+ numbers are assigned to these in order.
+- clock-frequency : Specifies the base frequency driving
+ the BRG.
+
+Example:
+ brg@119f0 {
+ compatible = "fsl,mpc8272-brg",
+ "fsl,cpm2-brg",
+ "fsl,cpm-brg";
+ reg = <119f0 10 115f0 10>;
+ clock-frequency = <d#25000000>;
+ };
diff --git a/Documentation/powerpc/dts-bindings/fsl/cpm_qe/cpm/i2c.txt b/Documentation/powerpc/dts-bindings/fsl/cpm_qe/cpm/i2c.txt
new file mode 100644
index 0000000..87bc604
--- /dev/null
+++ b/Documentation/powerpc/dts-bindings/fsl/cpm_qe/cpm/i2c.txt
@@ -0,0 +1,41 @@
+* I2C
+
+The I2C controller is expressed as a bus under the CPM node.
+
+Properties:
+- compatible : "fsl,cpm1-i2c", "fsl,cpm2-i2c"
+- reg : On CPM2 devices, the second resource doesn't specify the I2C
+ Parameter RAM itself, but the I2C_BASE field of the CPM2 Parameter RAM
+ (typically 0x8afc 0x2).
+- #address-cells : Should be one. The cell is the i2c device address with
+ the r/w bit set to zero.
+- #size-cells : Should be zero.
+- clock-frequency : Can be used to set the i2c clock frequency. If
+ unspecified, a default frequency of 60kHz is being used.
+The following two properties are deprecated. They are only used by legacy
+i2c drivers to find the bus to probe:
+- linux,i2c-index : Can be used to hard code an i2c bus number. By default,
+ the bus number is dynamically assigned by the i2c core.
+- linux,i2c-class : Can be used to override the i2c class. The class is used
+ by legacy i2c device drivers to find a bus in a specific context like
+ system management, video or sound. By default, I2C_CLASS_HWMON (1) is
+ being used. The definition of the classes can be found in
+ include/i2c/i2c.h
+
+Example, based on mpc823:
+
+ i2c@860 {
+ compatible = "fsl,mpc823-i2c",
+ "fsl,cpm1-i2c";
+ reg = <0x860 0x20 0x3c80 0x30>;
+ interrupts = <16>;
+ interrupt-parent = <&CPM_PIC>;
+ fsl,cpm-command = <0x10>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ rtc@68 {
+ compatible = "dallas,ds1307";
+ reg = <0x68>;
+ };
+ };
diff --git a/Documentation/powerpc/dts-bindings/fsl/cpm_qe/cpm/pic.txt b/Documentation/powerpc/dts-bindings/fsl/cpm_qe/cpm/pic.txt
new file mode 100644
index 0000000..8e3ee16
--- /dev/null
+++ b/Documentation/powerpc/dts-bindings/fsl/cpm_qe/cpm/pic.txt
@@ -0,0 +1,18 @@
+* Interrupt Controllers
+
+Currently defined compatibles:
+- fsl,cpm1-pic
+ - only one interrupt cell
+- fsl,pq1-pic
+- fsl,cpm2-pic
+ - second interrupt cell is level/sense:
+ - 2 is falling edge
+ - 8 is active low
+
+Example:
+ interrupt-controller@10c00 {
+ #interrupt-cells = <2>;
+ interrupt-controller;
+ reg = <10c00 80>;
+ compatible = "mpc8272-pic", "fsl,cpm2-pic";
+ };
diff --git a/Documentation/powerpc/dts-bindings/fsl/cpm_qe/cpm/usb.txt b/Documentation/powerpc/dts-bindings/fsl/cpm_qe/cpm/usb.txt
new file mode 100644
index 0000000..74bfda4
--- /dev/null
+++ b/Documentation/powerpc/dts-bindings/fsl/cpm_qe/cpm/usb.txt
@@ -0,0 +1,15 @@
+* USB (Universal Serial Bus Controller)
+
+Properties:
+- compatible : "fsl,cpm1-usb", "fsl,cpm2-usb", "fsl,qe-usb"
+
+Example:
+ usb@11bc0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,cpm2-usb";
+ reg = <11b60 18 8b00 100>;
+ interrupts = <b 8>;
+ interrupt-parent = <&PIC>;
+ fsl,cpm-command = <2e600000>;
+ };
diff --git a/Documentation/powerpc/dts-bindings/fsl/cpm_qe/network.txt b/Documentation/powerpc/dts-bindings/fsl/cpm_qe/network.txt
new file mode 100644
index 0000000..0e42694
--- /dev/null
+++ b/Documentation/powerpc/dts-bindings/fsl/cpm_qe/network.txt
@@ -0,0 +1,45 @@
+* Network
+
+Currently defined compatibles:
+- fsl,cpm1-scc-enet
+- fsl,cpm2-scc-enet
+- fsl,cpm1-fec-enet
+- fsl,cpm2-fcc-enet (third resource is GFEMR)
+- fsl,qe-enet
+
+Example:
+
+ ethernet@11300 {
+ device_type = "network";
+ compatible = "fsl,mpc8272-fcc-enet",
+ "fsl,cpm2-fcc-enet";
+ reg = <11300 20 8400 100 11390 1>;
+ local-mac-address = [ 00 00 00 00 00 00 ];
+ interrupts = <20 8>;
+ interrupt-parent = <&PIC>;
+ phy-handle = <&PHY0>;
+ fsl,cpm-command = <12000300>;
+ };
+
+* MDIO
+
+Currently defined compatibles:
+fsl,pq1-fec-mdio (reg is same as first resource of FEC device)
+fsl,cpm2-mdio-bitbang (reg is port C registers)
+
+Properties for fsl,cpm2-mdio-bitbang:
+fsl,mdio-pin : pin of port C controlling mdio data
+fsl,mdc-pin : pin of port C controlling mdio clock
+
+Example:
+ mdio@10d40 {
+ device_type = "mdio";
+ compatible = "fsl,mpc8272ads-mdio-bitbang",
+ "fsl,mpc8272-mdio-bitbang",
+ "fsl,cpm2-mdio-bitbang";
+ reg = <10d40 14>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ fsl,mdio-pin = <12>;
+ fsl,mdc-pin = <13>;
+ };
diff --git a/Documentation/powerpc/dts-bindings/fsl/cpm_qe/qe.txt b/Documentation/powerpc/dts-bindings/fsl/cpm_qe/qe.txt
new file mode 100644
index 0000000..78790d5
--- /dev/null
+++ b/Documentation/powerpc/dts-bindings/fsl/cpm_qe/qe.txt
@@ -0,0 +1,58 @@
+* Freescale QUICC Engine module (QE)
+This represents qe module that is installed on PowerQUICC II Pro.
+
+NOTE: This is an interim binding; it should be updated to fit
+in with the CPM binding later in this document.
+
+Basically, it is a bus of devices, that could act more or less
+as a complete entity (UCC, USB etc ). All of them should be siblings on
+the "root" qe node, using the common properties from there.
+The description below applies to the qe of MPC8360 and
+more nodes and properties would be extended in the future.
+
+i) Root QE device
+
+Required properties:
+- compatible : should be "fsl,qe";
+- model : precise model of the QE, Can be "QE", "CPM", or "CPM2"
+- reg : offset and length of the device registers.
+- bus-frequency : the clock frequency for QUICC Engine.
+
+Recommended properties
+- brg-frequency : the internal clock source frequency for baud-rate
+ generators in Hz.
+
+Example:
+ qe@e0100000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ #interrupt-cells = <2>;
+ compatible = "fsl,qe";
+ ranges = <0 e0100000 00100000>;
+ reg = <e0100000 480>;
+ brg-frequency = <0>;
+ bus-frequency = <179A7B00>;
+ }
+
+* Multi-User RAM (MURAM)
+
+Required properties:
+- compatible : should be "fsl,qe-muram", "fsl,cpm-muram".
+- mode : the could be "host" or "slave".
+- ranges : Should be defined as specified in 1) to describe the
+ translation of MURAM addresses.
+- data-only : sub-node which defines the address area under MURAM
+ bus that can be allocated as data/parameter
+
+Example:
+
+ muram@10000 {
+ compatible = "fsl,qe-muram", "fsl,cpm-muram";
+ ranges = <0 00010000 0000c000>;
+
+ data-only@0{
+ compatible = "fsl,qe-muram-data",
+ "fsl,cpm-muram-data";
+ reg = <0 c000>;
+ };
+ };
diff --git a/Documentation/powerpc/dts-bindings/fsl/cpm_qe/qe/firmware.txt b/Documentation/powerpc/dts-bindings/fsl/cpm_qe/qe/firmware.txt
new file mode 100644
index 0000000..6c238f5
--- /dev/null
+++ b/Documentation/powerpc/dts-bindings/fsl/cpm_qe/qe/firmware.txt
@@ -0,0 +1,24 @@
+* Uploaded QE firmware
+
+ If a new firwmare has been uploaded to the QE (usually by the
+ boot loader), then a 'firmware' child node should be added to the QE
+ node. This node provides information on the uploaded firmware that
+ device drivers may need.
+
+ Required properties:
+ - id: The string name of the firmware. This is taken from the 'id'
+ member of the qe_firmware structure of the uploaded firmware.
+ Device drivers can search this string to determine if the
+ firmware they want is already present.
+ - extended-modes: The Extended Modes bitfield, taken from the
+ firmware binary. It is a 64-bit number represented
+ as an array of two 32-bit numbers.
+ - virtual-traps: The virtual traps, taken from the firmware binary.
+ It is an array of 8 32-bit numbers.
+
+Example:
+ firmware {
+ id = "Soft-UART";
+ extended-modes = <0 0>;
+ virtual-traps = <0 0 0 0 0 0 0 0>;
+ };
diff --git a/Documentation/powerpc/dts-bindings/fsl/cpm_qe/qe/par_io.txt b/Documentation/powerpc/dts-bindings/fsl/cpm_qe/qe/par_io.txt
new file mode 100644
index 0000000..6098426
--- /dev/null
+++ b/Documentation/powerpc/dts-bindings/fsl/cpm_qe/qe/par_io.txt
@@ -0,0 +1,51 @@
+* Parallel I/O Ports
+
+This node configures Parallel I/O ports for CPUs with QE support.
+The node should reside in the "soc" node of the tree. For each
+device that using parallel I/O ports, a child node should be created.
+See the definition of the Pin configuration nodes below for more
+information.
+
+Required properties:
+- device_type : should be "par_io".
+- reg : offset to the register set and its length.
+- num-ports : number of Parallel I/O ports
+
+Example:
+par_io@1400 {
+ reg = <1400 100>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ device_type = "par_io";
+ num-ports = <7>;
+ ucc_pin@01 {
+ ......
+ };
+
+Note that "par_io" nodes are obsolete, and should not be used for
+the new device trees. Instead, each Par I/O bank should be represented
+via its own gpio-controller node:
+
+Required properties:
+- #gpio-cells : should be "2".
+- compatible : should be "fsl,<chip>-qe-pario-bank",
+ "fsl,mpc8323-qe-pario-bank".
+- reg : offset to the register set and its length.
+- gpio-controller : node to identify gpio controllers.
+
+Example:
+ qe_pio_a: gpio-controller@1400 {
+ #gpio-cells = <2>;
+ compatible = "fsl,mpc8360-qe-pario-bank",
+ "fsl,mpc8323-qe-pario-bank";
+ reg = <0x1400 0x18>;
+ gpio-controller;
+ };
+
+ qe_pio_e: gpio-controller@1460 {
+ #gpio-cells = <2>;
+ compatible = "fsl,mpc8360-qe-pario-bank",
+ "fsl,mpc8323-qe-pario-bank";
+ reg = <0x1460 0x18>;
+ gpio-controller;
+ };
diff --git a/Documentation/powerpc/dts-bindings/fsl/cpm_qe/qe/pincfg.txt b/Documentation/powerpc/dts-bindings/fsl/cpm_qe/qe/pincfg.txt
new file mode 100644
index 0000000..c5b4306
--- /dev/null
+++ b/Documentation/powerpc/dts-bindings/fsl/cpm_qe/qe/pincfg.txt
@@ -0,0 +1,60 @@
+* Pin configuration nodes
+
+Required properties:
+- linux,phandle : phandle of this node; likely referenced by a QE
+ device.
+- pio-map : array of pin configurations. Each pin is defined by 6
+ integers. The six numbers are respectively: port, pin, dir,
+ open_drain, assignment, has_irq.
+ - port : port number of the pin; 0-6 represent port A-G in UM.
+ - pin : pin number in the port.
+ - dir : direction of the pin, should encode as follows:
+
+ 0 = The pin is disabled
+ 1 = The pin is an output
+ 2 = The pin is an input
+ 3 = The pin is I/O
+
+ - open_drain : indicates the pin is normal or wired-OR:
+
+ 0 = The pin is actively driven as an output
+ 1 = The pin is an open-drain driver. As an output, the pin is
+ driven active-low, otherwise it is three-stated.
+
+ - assignment : function number of the pin according to the Pin Assignment
+ tables in User Manual. Each pin can have up to 4 possible functions in
+ QE and two options for CPM.
+ - has_irq : indicates if the pin is used as source of external
+ interrupts.
+
+Example:
+ ucc_pin@01 {
+ linux,phandle = <140001>;
+ pio-map = <
+ /* port pin dir open_drain assignment has_irq */
+ 0 3 1 0 1 0 /* TxD0 */
+ 0 4 1 0 1 0 /* TxD1 */
+ 0 5 1 0 1 0 /* TxD2 */
+ 0 6 1 0 1 0 /* TxD3 */
+ 1 6 1 0 3 0 /* TxD4 */
+ 1 7 1 0 1 0 /* TxD5 */
+ 1 9 1 0 2 0 /* TxD6 */
+ 1 a 1 0 2 0 /* TxD7 */
+ 0 9 2 0 1 0 /* RxD0 */
+ 0 a 2 0 1 0 /* RxD1 */
+ 0 b 2 0 1 0 /* RxD2 */
+ 0 c 2 0 1 0 /* RxD3 */
+ 0 d 2 0 1 0 /* RxD4 */
+ 1 1 2 0 2 0 /* RxD5 */
+ 1 0 2 0 2 0 /* RxD6 */
+ 1 4 2 0 2 0 /* RxD7 */
+ 0 7 1 0 1 0 /* TX_EN */
+ 0 8 1 0 1 0 /* TX_ER */
+ 0 f 2 0 1 0 /* RX_DV */
+ 0 10 2 0 1 0 /* RX_ER */
+ 0 0 2 0 1 0 /* RX_CLK */
+ 2 9 1 0 3 0 /* GTX_CLK - CLK10 */
+ 2 8 2 0 1 0>; /* GTX125 - CLK9 */
+ };
+
+
diff --git a/Documentation/powerpc/dts-bindings/fsl/cpm_qe/qe/ucc.txt b/Documentation/powerpc/dts-bindings/fsl/cpm_qe/qe/ucc.txt
new file mode 100644
index 0000000..e47734b
--- /dev/null
+++ b/Documentation/powerpc/dts-bindings/fsl/cpm_qe/qe/ucc.txt
@@ -0,0 +1,70 @@
+* UCC (Unified Communications Controllers)
+
+Required properties:
+- device_type : should be "network", "hldc", "uart", "transparent"
+ "bisync", "atm", or "serial".
+- compatible : could be "ucc_geth" or "fsl_atm" and so on.
+- cell-index : the ucc number(1-8), corresponding to UCCx in UM.
+- reg : Offset and length of the register set for the device
+- interrupts : <a b> where a is the interrupt number and b is a
+ field that represents an encoding of the sense and level
+ information for the interrupt. This should be encoded based on
+ the information in section 2) depending on the type of interrupt
+ controller you have.
+- interrupt-parent : the phandle for the interrupt controller that
+ services interrupts for this device.
+- pio-handle : The phandle for the Parallel I/O port configuration.
+- port-number : for UART drivers, the port number to use, between 0 and 3.
+ This usually corresponds to the /dev/ttyQE device, e.g. <0> = /dev/ttyQE0.
+ The port number is added to the minor number of the device. Unlike the
+ CPM UART driver, the port-number is required for the QE UART driver.
+- soft-uart : for UART drivers, if specified this means the QE UART device
+ driver should use "Soft-UART" mode, which is needed on some SOCs that have
+ broken UART hardware. Soft-UART is provided via a microcode upload.
+- rx-clock-name: the UCC receive clock source
+ "none": clock source is disabled
+ "brg1" through "brg16": clock source is BRG1-BRG16, respectively
+ "clk1" through "clk24": clock source is CLK1-CLK24, respectively
+- tx-clock-name: the UCC transmit clock source
+ "none": clock source is disabled
+ "brg1" through "brg16": clock source is BRG1-BRG16, respectively
+ "clk1" through "clk24": clock source is CLK1-CLK24, respectively
+The following two properties are deprecated. rx-clock has been replaced
+with rx-clock-name, and tx-clock has been replaced with tx-clock-name.
+Drivers that currently use the deprecated properties should continue to
+do so, in order to support older device trees, but they should be updated
+to check for the new properties first.
+- rx-clock : represents the UCC receive clock source.
+ 0x00 : clock source is disabled;
+ 0x1~0x10 : clock source is BRG1~BRG16 respectively;
+ 0x11~0x28: clock source is QE_CLK1~QE_CLK24 respectively.
+- tx-clock: represents the UCC transmit clock source;
+ 0x00 : clock source is disabled;
+ 0x1~0x10 : clock source is BRG1~BRG16 respectively;
+ 0x11~0x28: clock source is QE_CLK1~QE_CLK24 respectively.
+
+Required properties for network device_type:
+- mac-address : list of bytes representing the ethernet address.
+- phy-handle : The phandle for the PHY connected to this controller.
+
+Recommended properties:
+- phy-connection-type : a string naming the controller/PHY interface type,
+ i.e., "mii" (default), "rmii", "gmii", "rgmii", "rgmii-id" (Internal
+ Delay), "rgmii-txid" (delay on TX only), "rgmii-rxid" (delay on RX only),
+ "tbi", or "rtbi".
+
+Example:
+ ucc@2000 {
+ device_type = "network";
+ compatible = "ucc_geth";
+ cell-index = <1>;
+ reg = <2000 200>;
+ interrupts = <a0 0>;
+ interrupt-parent = <700>;
+ mac-address = [ 00 04 9f 00 23 23 ];
+ rx-clock = "none";
+ tx-clock = "clk9";
+ phy-handle = <212000>;
+ phy-connection-type = "gmii";
+ pio-handle = <140001>;
+ };
diff --git a/Documentation/powerpc/dts-bindings/fsl/cpm_qe/qe/usb.txt b/Documentation/powerpc/dts-bindings/fsl/cpm_qe/qe/usb.txt
new file mode 100644
index 0000000..c8f44d6
--- /dev/null
+++ b/Documentation/powerpc/dts-bindings/fsl/cpm_qe/qe/usb.txt
@@ -0,0 +1,22 @@
+* USB (Universal Serial Bus Controller)
+
+Required properties:
+- compatible : could be "qe_udc" or "fhci-hcd".
+- mode : the could be "host" or "slave".
+- reg : Offset and length of the register set for the device
+- interrupts : <a b> where a is the interrupt number and b is a
+ field that represents an encoding of the sense and level
+ information for the interrupt. This should be encoded based on
+ the information in section 2) depending on the type of interrupt
+ controller you have.
+- interrupt-parent : the phandle for the interrupt controller that
+ services interrupts for this device.
+
+Example(slave):
+ usb@6c0 {
+ compatible = "qe_udc";
+ reg = <6c0 40>;
+ interrupts = <8b 0>;
+ interrupt-parent = <700>;
+ mode = "slave";
+ };
diff --git a/Documentation/powerpc/dts-bindings/fsl/cpm_qe/serial.txt b/Documentation/powerpc/dts-bindings/fsl/cpm_qe/serial.txt
new file mode 100644
index 0000000..b35f348
--- /dev/null
+++ b/Documentation/powerpc/dts-bindings/fsl/cpm_qe/serial.txt
@@ -0,0 +1,21 @@
+* Serial
+
+Currently defined compatibles:
+- fsl,cpm1-smc-uart
+- fsl,cpm2-smc-uart
+- fsl,cpm1-scc-uart
+- fsl,cpm2-scc-uart
+- fsl,qe-uart
+
+Example:
+
+ serial@11a00 {
+ device_type = "serial";
+ compatible = "fsl,mpc8272-scc-uart",
+ "fsl,cpm2-scc-uart";
+ reg = <11a00 20 8000 100>;
+ interrupts = <28 8>;
+ interrupt-parent = <&PIC>;
+ fsl,cpm-brg = <1>;
+ fsl,cpm-command = <00800000>;
+ };
diff --git a/Documentation/powerpc/dts-bindings/fsl/diu.txt b/Documentation/powerpc/dts-bindings/fsl/diu.txt
new file mode 100644
index 0000000..deb35de
--- /dev/null
+++ b/Documentation/powerpc/dts-bindings/fsl/diu.txt
@@ -0,0 +1,18 @@
+* Freescale Display Interface Unit
+
+The Freescale DIU is a LCD controller, with proper hardware, it can also
+drive DVI monitors.
+
+Required properties:
+- compatible : should be "fsl-diu".
+- reg : should contain at least address and length of the DIU register
+ set.
+- Interrupts : one DIU interrupt should be describe here.
+
+Example (MPC8610HPCD):
+ display@2c000 {
+ compatible = "fsl,diu";
+ reg = <0x2c000 100>;
+ interrupts = <72 2>;
+ interrupt-parent = <&mpic>;
+ };
diff --git a/Documentation/powerpc/dts-bindings/fsl/dma.txt b/Documentation/powerpc/dts-bindings/fsl/dma.txt
new file mode 100644
index 0000000..86826df
--- /dev/null
+++ b/Documentation/powerpc/dts-bindings/fsl/dma.txt
@@ -0,0 +1,127 @@
+* Freescale 83xx DMA Controller
+
+Freescale PowerPC 83xx have on chip general purpose DMA controllers.
+
+Required properties:
+
+- compatible : compatible list, contains 2 entries, first is
+ "fsl,CHIP-dma", where CHIP is the processor
+ (mpc8349, mpc8360, etc.) and the second is
+ "fsl,elo-dma"
+- reg : <registers mapping for DMA general status reg>
+- ranges : Should be defined as specified in 1) to describe the
+ DMA controller channels.
+- cell-index : controller index. 0 for controller @ 0x8100
+- interrupts : <interrupt mapping for DMA IRQ>
+- interrupt-parent : optional, if needed for interrupt mapping
+
+
+- DMA channel nodes:
+ - compatible : compatible list, contains 2 entries, first is
+ "fsl,CHIP-dma-channel", where CHIP is the processor
+ (mpc8349, mpc8350, etc.) and the second is
+ "fsl,elo-dma-channel"
+ - reg : <registers mapping for channel>
+ - cell-index : dma channel index starts at 0.
+
+Optional properties:
+ - interrupts : <interrupt mapping for DMA channel IRQ>
+ (on 83xx this is expected to be identical to
+ the interrupts property of the parent node)
+ - interrupt-parent : optional, if needed for interrupt mapping
+
+Example:
+ dma@82a8 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "fsl,mpc8349-dma", "fsl,elo-dma";
+ reg = <82a8 4>;
+ ranges = <0 8100 1a4>;
+ interrupt-parent = <&ipic>;
+ interrupts = <47 8>;
+ cell-index = <0>;
+ dma-channel@0 {
+ compatible = "fsl,mpc8349-dma-channel", "fsl,elo-dma-channel";
+ cell-index = <0>;
+ reg = <0 80>;
+ };
+ dma-channel@80 {
+ compatible = "fsl,mpc8349-dma-channel", "fsl,elo-dma-channel";
+ cell-index = <1>;
+ reg = <80 80>;
+ };
+ dma-channel@100 {
+ compatible = "fsl,mpc8349-dma-channel", "fsl,elo-dma-channel";
+ cell-index = <2>;
+ reg = <100 80>;
+ };
+ dma-channel@180 {
+ compatible = "fsl,mpc8349-dma-channel", "fsl,elo-dma-channel";
+ cell-index = <3>;
+ reg = <180 80>;
+ };
+ };
+
+* Freescale 85xx/86xx DMA Controller
+
+Freescale PowerPC 85xx/86xx have on chip general purpose DMA controllers.
+
+Required properties:
+
+- compatible : compatible list, contains 2 entries, first is
+ "fsl,CHIP-dma", where CHIP is the processor
+ (mpc8540, mpc8540, etc.) and the second is
+ "fsl,eloplus-dma"
+- reg : <registers mapping for DMA general status reg>
+- cell-index : controller index. 0 for controller @ 0x21000,
+ 1 for controller @ 0xc000
+- ranges : Should be defined as specified in 1) to describe the
+ DMA controller channels.
+
+- DMA channel nodes:
+ - compatible : compatible list, contains 2 entries, first is
+ "fsl,CHIP-dma-channel", where CHIP is the processor
+ (mpc8540, mpc8560, etc.) and the second is
+ "fsl,eloplus-dma-channel"
+ - cell-index : dma channel index starts at 0.
+ - reg : <registers mapping for channel>
+ - interrupts : <interrupt mapping for DMA channel IRQ>
+ - interrupt-parent : optional, if needed for interrupt mapping
+
+Example:
+ dma@21300 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "fsl,mpc8540-dma", "fsl,eloplus-dma";
+ reg = <21300 4>;
+ ranges = <0 21100 200>;
+ cell-index = <0>;
+ dma-channel@0 {
+ compatible = "fsl,mpc8540-dma-channel", "fsl,eloplus-dma-channel";
+ reg = <0 80>;
+ cell-index = <0>;
+ interrupt-parent = <&mpic>;
+ interrupts = <14 2>;
+ };
+ dma-channel@80 {
+ compatible = "fsl,mpc8540-dma-channel", "fsl,eloplus-dma-channel";
+ reg = <80 80>;
+ cell-index = <1>;
+ interrupt-parent = <&mpic>;
+ interrupts = <15 2>;
+ };
+ dma-channel@100 {
+ compatible = "fsl,mpc8540-dma-channel", "fsl,eloplus-dma-channel";
+ reg = <100 80>;
+ cell-index = <2>;
+ interrupt-parent = <&mpic>;
+ interrupts = <16 2>;
+ };
+ dma-channel@180 {
+ compatible = "fsl,mpc8540-dma-channel", "fsl,eloplus-dma-channel";
+ reg = <180 80>;
+ cell-index = <3>;
+ interrupt-parent = <&mpic>;
+ interrupts = <17 2>;
+ };
+ };
diff --git a/Documentation/powerpc/dts-bindings/fsl/gtm.txt b/Documentation/powerpc/dts-bindings/fsl/gtm.txt
new file mode 100644
index 0000000..9a33efd
--- /dev/null
+++ b/Documentation/powerpc/dts-bindings/fsl/gtm.txt
@@ -0,0 +1,31 @@
+* Freescale General-purpose Timers Module
+
+Required properties:
+ - compatible : should be
+ "fsl,<chip>-gtm", "fsl,gtm" for SOC GTMs
+ "fsl,<chip>-qe-gtm", "fsl,qe-gtm", "fsl,gtm" for QE GTMs
+ "fsl,<chip>-cpm2-gtm", "fsl,cpm2-gtm", "fsl,gtm" for CPM2 GTMs
+ - reg : should contain gtm registers location and length (0x40).
+ - interrupts : should contain four interrupts.
+ - interrupt-parent : interrupt source phandle.
+ - clock-frequency : specifies the frequency driving the timer.
+
+Example:
+
+timer@500 {
+ compatible = "fsl,mpc8360-gtm", "fsl,gtm";
+ reg = <0x500 0x40>;
+ interrupts = <90 8 78 8 84 8 72 8>;
+ interrupt-parent = <&ipic>;
+ /* filled by u-boot */
+ clock-frequency = <0>;
+};
+
+timer@440 {
+ compatible = "fsl,mpc8360-qe-gtm", "fsl,qe-gtm", "fsl,gtm";
+ reg = <0x440 0x40>;
+ interrupts = <12 13 14 15>;
+ interrupt-parent = <&qeic>;
+ /* filled by u-boot */
+ clock-frequency = <0>;
+};
diff --git a/Documentation/powerpc/dts-bindings/fsl/guts.txt b/Documentation/powerpc/dts-bindings/fsl/guts.txt
new file mode 100644
index 0000000..9e7a241
--- /dev/null
+++ b/Documentation/powerpc/dts-bindings/fsl/guts.txt
@@ -0,0 +1,25 @@
+* Global Utilities Block
+
+The global utilities block controls power management, I/O device
+enabling, power-on-reset configuration monitoring, general-purpose
+I/O signal configuration, alternate function selection for multiplexed
+signals, and clock control.
+
+Required properties:
+
+ - compatible : Should define the compatible device type for
+ global-utilities.
+ - reg : Offset and length of the register set for the device.
+
+Recommended properties:
+
+ - fsl,has-rstcr : Indicates that the global utilities register set
+ contains a functioning "reset control register" (i.e. the board
+ is wired to reset upon setting the HRESET_REQ bit in this register).
+
+Example:
+ global-utilities@e0000 { /* global utilities block */
+ compatible = "fsl,mpc8548-guts";
+ reg = <e0000 1000>;
+ fsl,has-rstcr;
+ };
diff --git a/Documentation/powerpc/dts-bindings/fsl/i2c.txt b/Documentation/powerpc/dts-bindings/fsl/i2c.txt
new file mode 100644
index 0000000..d0ab33e
--- /dev/null
+++ b/Documentation/powerpc/dts-bindings/fsl/i2c.txt
@@ -0,0 +1,32 @@
+* I2C
+
+Required properties :
+
+ - device_type : Should be "i2c"
+ - reg : Offset and length of the register set for the device
+
+Recommended properties :
+
+ - compatible : Should be "fsl-i2c" for parts compatible with
+ Freescale I2C specifications.
+ - interrupts : <a b> where a is the interrupt number and b is a
+ field that represents an encoding of the sense and level
+ information for the interrupt. This should be encoded based on
+ the information in section 2) depending on the type of interrupt
+ controller you have.
+ - interrupt-parent : the phandle for the interrupt controller that
+ services interrupts for this device.
+ - dfsrr : boolean; if defined, indicates that this I2C device has
+ a digital filter sampling rate register
+ - fsl5200-clocking : boolean; if defined, indicated that this device
+ uses the FSL 5200 clocking mechanism.
+
+Example :
+ i2c@3000 {
+ interrupt-parent = <40000>;
+ interrupts = <1b 3>;
+ reg = <3000 18>;
+ device_type = "i2c";
+ compatible = "fsl-i2c";
+ dfsrr;
+ };
diff --git a/Documentation/powerpc/dts-bindings/fsl/lbc.txt b/Documentation/powerpc/dts-bindings/fsl/lbc.txt
new file mode 100644
index 0000000..3300fec
--- /dev/null
+++ b/Documentation/powerpc/dts-bindings/fsl/lbc.txt
@@ -0,0 +1,35 @@
+* Chipselect/Local Bus
+
+Properties:
+- name : Should be localbus
+- #address-cells : Should be either two or three. The first cell is the
+ chipselect number, and the remaining cells are the
+ offset into the chipselect.
+- #size-cells : Either one or two, depending on how large each chipselect
+ can be.
+- ranges : Each range corresponds to a single chipselect, and cover
+ the entire access window as configured.
+
+Example:
+ localbus@f0010100 {
+ compatible = "fsl,mpc8272-localbus",
+ "fsl,pq2-localbus";
+ #address-cells = <2>;
+ #size-cells = <1>;
+ reg = <f0010100 40>;
+
+ ranges = <0 0 fe000000 02000000
+ 1 0 f4500000 00008000>;
+
+ flash@0,0 {
+ compatible = "jedec-flash";
+ reg = <0 0 2000000>;
+ bank-width = <4>;
+ device-width = <1>;
+ };
+
+ board-control@1,0 {
+ reg = <1 0 20>;
+ compatible = "fsl,mpc8272ads-bcsr";
+ };
+ };
diff --git a/Documentation/powerpc/dts-bindings/fsl/msi-pic.txt b/Documentation/powerpc/dts-bindings/fsl/msi-pic.txt
new file mode 100644
index 0000000..b26b919
--- /dev/null
+++ b/Documentation/powerpc/dts-bindings/fsl/msi-pic.txt
@@ -0,0 +1,36 @@
+* Freescale MSI interrupt controller
+
+Reguired properities:
+- compatible : compatible list, contains 2 entries,
+ first is "fsl,CHIP-msi", where CHIP is the processor(mpc8610, mpc8572,
+ etc.) and the second is "fsl,mpic-msi" or "fsl,ipic-msi" depending on
+ the parent type.
+- reg : should contain the address and the length of the shared message
+ interrupt register set.
+- msi-available-ranges: use <start count> style section to define which
+ msi interrupt can be used in the 256 msi interrupts. This property is
+ optional, without this, all the 256 MSI interrupts can be used.
+- interrupts : each one of the interrupts here is one entry per 32 MSIs,
+ and routed to the host interrupt controller. the interrupts should
+ be set as edge sensitive.
+- interrupt-parent: the phandle for the interrupt controller
+ that services interrupts for this device. for 83xx cpu, the interrupts
+ are routed to IPIC, and for 85xx/86xx cpu the interrupts are routed
+ to MPIC.
+
+Example:
+ msi@41600 {
+ compatible = "fsl,mpc8610-msi", "fsl,mpic-msi";
+ reg = <0x41600 0x80>;
+ msi-available-ranges = <0 0x100>;
+ interrupts = <
+ 0xe0 0
+ 0xe1 0
+ 0xe2 0
+ 0xe3 0
+ 0xe4 0
+ 0xe5 0
+ 0xe6 0
+ 0xe7 0>;
+ interrupt-parent = <&mpic>;
+ };
diff --git a/Documentation/powerpc/dts-bindings/fsl/sata.txt b/Documentation/powerpc/dts-bindings/fsl/sata.txt
new file mode 100644
index 0000000..b46bcf4
--- /dev/null
+++ b/Documentation/powerpc/dts-bindings/fsl/sata.txt
@@ -0,0 +1,29 @@
+* Freescale 8xxx/3.0 Gb/s SATA nodes
+
+SATA nodes are defined to describe on-chip Serial ATA controllers.
+Each SATA port should have its own node.
+
+Required properties:
+- compatible : compatible list, contains 2 entries, first is
+ "fsl,CHIP-sata", where CHIP is the processor
+ (mpc8315, mpc8379, etc.) and the second is
+ "fsl,pq-sata"
+- interrupts : <interrupt mapping for SATA IRQ>
+- cell-index : controller index.
+ 1 for controller @ 0x18000
+ 2 for controller @ 0x19000
+ 3 for controller @ 0x1a000
+ 4 for controller @ 0x1b000
+
+Optional properties:
+- interrupt-parent : optional, if needed for interrupt mapping
+- reg : <registers mapping>
+
+Example:
+ sata@18000 {
+ compatible = "fsl,mpc8379-sata", "fsl,pq-sata";
+ reg = <0x18000 0x1000>;
+ cell-index = <1>;
+ interrupts = <2c 8>;
+ interrupt-parent = < &ipic >;
+ };
diff --git a/Documentation/powerpc/dts-bindings/fsl/spi.txt b/Documentation/powerpc/dts-bindings/fsl/spi.txt
new file mode 100644
index 0000000..e7d9a34
--- /dev/null
+++ b/Documentation/powerpc/dts-bindings/fsl/spi.txt
@@ -0,0 +1,24 @@
+* SPI (Serial Peripheral Interface)
+
+Required properties:
+- cell-index : SPI controller index.
+- compatible : should be "fsl,spi".
+- mode : the SPI operation mode, it can be "cpu" or "cpu-qe".
+- reg : Offset and length of the register set for the device
+- interrupts : <a b> where a is the interrupt number and b is a
+ field that represents an encoding of the sense and level
+ information for the interrupt. This should be encoded based on
+ the information in section 2) depending on the type of interrupt
+ controller you have.
+- interrupt-parent : the phandle for the interrupt controller that
+ services interrupts for this device.
+
+Example:
+ spi@4c0 {
+ cell-index = <0>;
+ compatible = "fsl,spi";
+ reg = <4c0 40>;
+ interrupts = <82 0>;
+ interrupt-parent = <700>;
+ mode = "cpu";
+ };
diff --git a/Documentation/powerpc/dts-bindings/fsl/ssi.txt b/Documentation/powerpc/dts-bindings/fsl/ssi.txt
new file mode 100644
index 0000000..d100555
--- /dev/null
+++ b/Documentation/powerpc/dts-bindings/fsl/ssi.txt
@@ -0,0 +1,38 @@
+Freescale Synchronous Serial Interface
+
+The SSI is a serial device that communicates with audio codecs. It can
+be programmed in AC97, I2S, left-justified, or right-justified modes.
+
+Required properties:
+- compatible : compatible list, containing "fsl,ssi"
+- cell-index : the SSI, <0> = SSI1, <1> = SSI2, and so on
+- reg : offset and length of the register set for the device
+- interrupts : <a b> where a is the interrupt number and b is a
+ field that represents an encoding of the sense and
+ level information for the interrupt. This should be
+ encoded based on the information in section 2)
+ depending on the type of interrupt controller you
+ have.
+- interrupt-parent : the phandle for the interrupt controller that
+ services interrupts for this device.
+- fsl,mode : the operating mode for the SSI interface
+ "i2s-slave" - I2S mode, SSI is clock slave
+ "i2s-master" - I2S mode, SSI is clock master
+ "lj-slave" - left-justified mode, SSI is clock slave
+ "lj-master" - l.j. mode, SSI is clock master
+ "rj-slave" - right-justified mode, SSI is clock slave
+ "rj-master" - r.j., SSI is clock master
+ "ac97-slave" - AC97 mode, SSI is clock slave
+ "ac97-master" - AC97 mode, SSI is clock master
+
+Optional properties:
+- codec-handle : phandle to a 'codec' node that defines an audio
+ codec connected to this SSI. This node is typically
+ a child of an I2C or other control node.
+
+Child 'codec' node required properties:
+- compatible : compatible list, contains the name of the codec
+
+Child 'codec' node optional properties:
+- clock-frequency : The frequency of the input clock, which typically
+ comes from an on-board dedicated oscillator.
diff --git a/Documentation/powerpc/dts-bindings/fsl/tsec.txt b/Documentation/powerpc/dts-bindings/fsl/tsec.txt
new file mode 100644
index 0000000..583ef6b
--- /dev/null
+++ b/Documentation/powerpc/dts-bindings/fsl/tsec.txt
@@ -0,0 +1,69 @@
+* MDIO IO device
+
+The MDIO is a bus to which the PHY devices are connected. For each
+device that exists on this bus, a child node should be created. See
+the definition of the PHY node below for an example of how to define
+a PHY.
+
+Required properties:
+ - reg : Offset and length of the register set for the device
+ - compatible : Should define the compatible device type for the
+ mdio. Currently, this is most likely to be "fsl,gianfar-mdio"
+
+Example:
+
+ mdio@24520 {
+ reg = <24520 20>;
+ compatible = "fsl,gianfar-mdio";
+
+ ethernet-phy@0 {
+ ......
+ };
+ };
+
+
+* Gianfar-compatible ethernet nodes
+
+Required properties:
+
+ - device_type : Should be "network"
+ - model : Model of the device. Can be "TSEC", "eTSEC", or "FEC"
+ - compatible : Should be "gianfar"
+ - reg : Offset and length of the register set for the device
+ - mac-address : List of bytes representing the ethernet address of
+ this controller
+ - interrupts : <a b> where a is the interrupt number and b is a
+ field that represents an encoding of the sense and level
+ information for the interrupt. This should be encoded based on
+ the information in section 2) depending on the type of interrupt
+ controller you have.
+ - interrupt-parent : the phandle for the interrupt controller that
+ services interrupts for this device.
+ - phy-handle : The phandle for the PHY connected to this ethernet
+ controller.
+ - fixed-link : <a b c d e> where a is emulated phy id - choose any,
+ but unique to the all specified fixed-links, b is duplex - 0 half,
+ 1 full, c is link speed - d#10/d#100/d#1000, d is pause - 0 no
+ pause, 1 pause, e is asym_pause - 0 no asym_pause, 1 asym_pause.
+
+Recommended properties:
+
+ - phy-connection-type : a string naming the controller/PHY interface type,
+ i.e., "mii" (default), "rmii", "gmii", "rgmii", "rgmii-id", "sgmii",
+ "tbi", or "rtbi". This property is only really needed if the connection
+ is of type "rgmii-id", as all other connection types are detected by
+ hardware.
+
+
+Example:
+ ethernet@24000 {
+ #size-cells = <0>;
+ device_type = "network";
+ model = "TSEC";
+ compatible = "gianfar";
+ reg = <24000 1000>;
+ mac-address = [ 00 E0 0C 00 73 00 ];
+ interrupts = <d 3 e 3 12 3>;
+ interrupt-parent = <40000>;
+ phy-handle = <2452000>
+ };
diff --git a/Documentation/powerpc/dts-bindings/fsl/usb.txt b/Documentation/powerpc/dts-bindings/fsl/usb.txt
new file mode 100644
index 0000000..b001524
--- /dev/null
+++ b/Documentation/powerpc/dts-bindings/fsl/usb.txt
@@ -0,0 +1,59 @@
+Freescale SOC USB controllers
+
+The device node for a USB controller that is part of a Freescale
+SOC is as described in the document "Open Firmware Recommended
+Practice : Universal Serial Bus" with the following modifications
+and additions :
+
+Required properties :
+ - compatible : Should be "fsl-usb2-mph" for multi port host USB
+ controllers, or "fsl-usb2-dr" for dual role USB controllers
+ - phy_type : For multi port host USB controllers, should be one of
+ "ulpi", or "serial". For dual role USB controllers, should be
+ one of "ulpi", "utmi", "utmi_wide", or "serial".
+ - reg : Offset and length of the register set for the device
+ - port0 : boolean; if defined, indicates port0 is connected for
+ fsl-usb2-mph compatible controllers. Either this property or
+ "port1" (or both) must be defined for "fsl-usb2-mph" compatible
+ controllers.
+ - port1 : boolean; if defined, indicates port1 is connected for
+ fsl-usb2-mph compatible controllers. Either this property or
+ "port0" (or both) must be defined for "fsl-usb2-mph" compatible
+ controllers.
+ - dr_mode : indicates the working mode for "fsl-usb2-dr" compatible
+ controllers. Can be "host", "peripheral", or "otg". Default to
+ "host" if not defined for backward compatibility.
+
+Recommended properties :
+ - interrupts : <a b> where a is the interrupt number and b is a
+ field that represents an encoding of the sense and level
+ information for the interrupt. This should be encoded based on
+ the information in section 2) depending on the type of interrupt
+ controller you have.
+ - interrupt-parent : the phandle for the interrupt controller that
+ services interrupts for this device.
+
+Example multi port host USB controller device node :
+ usb@22000 {
+ compatible = "fsl-usb2-mph";
+ reg = <22000 1000>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interrupt-parent = <700>;
+ interrupts = <27 1>;
+ phy_type = "ulpi";
+ port0;
+ port1;
+ };
+
+Example dual role USB controller device node :
+ usb@23000 {
+ compatible = "fsl-usb2-dr";
+ reg = <23000 1000>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interrupt-parent = <700>;
+ interrupts = <26 1>;
+ dr_mode = "otg";
+ phy = "ulpi";
+ };