nand: omap2: Replace pr_err with dev_err
Usage of pr_err is frowned upon, so replace it with dev_err.
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
diff --git a/drivers/mtd/nand/omap2.c b/drivers/mtd/nand/omap2.c
index f97a4ff..3b357e9 100644
--- a/drivers/mtd/nand/omap2.c
+++ b/drivers/mtd/nand/omap2.c
@@ -1375,7 +1375,7 @@
erased_ecc_vec = bch16_vector;
break;
default:
- pr_err("invalid driver configuration\n");
+ dev_err(&info->pdev->dev, "invalid driver configuration\n");
return -EINVAL;
}
@@ -1446,7 +1446,8 @@
err = 0;
for (i = 0; i < eccsteps; i++) {
if (err_vec[i].error_uncorrectable) {
- pr_err("nand: uncorrectable bit-flips found\n");
+ dev_err(&info->pdev->dev,
+ "uncorrectable bit-flips found\n");
err = -EBADMSG;
} else if (err_vec[i].error_reported) {
for (j = 0; j < err_vec[i].error_count; j++) {
@@ -1483,8 +1484,9 @@
1 << bit_pos;
}
} else {
- pr_err("invalid bit-flip @ %d:%d\n",
- byte_pos, bit_pos);
+ dev_err(&info->pdev->dev,
+ "invalid bit-flip @ %d:%d\n",
+ byte_pos, bit_pos);
err = -EBADMSG;
}
}
@@ -1598,13 +1600,13 @@
/* check whether elm-id is passed via DT */
if (!elm_node) {
- pr_err("nand: error: ELM DT node not found\n");
+ dev_err(&info->pdev->dev, "ELM devicetree node not found\n");
return false;
}
pdev = of_find_device_by_node(elm_node);
/* check whether ELM device is registered */
if (!pdev) {
- pr_err("nand: error: ELM device not found\n");
+ dev_err(&info->pdev->dev, "ELM device not found\n");
return false;
}
/* ELM module available, now configure it */
@@ -1734,14 +1736,14 @@
/* scan NAND device connected to chip controller */
nand_chip->options |= pdata->devsize & NAND_BUSWIDTH_16;
if (nand_scan_ident(mtd, 1, NULL)) {
- pr_err("nand device scan failed, may be bus-width mismatch\n");
+ dev_err(&info->pdev->dev, "scan failed, may be bus-width mismatch\n");
err = -ENXIO;
goto return_error;
}
/* check for small page devices */
if ((mtd->oobsize < 64) && (pdata->ecc_opt != OMAP_ECC_HAM1_CODE_HW)) {
- pr_err("small page devices are not supported\n");
+ dev_err(&info->pdev->dev, "small page devices are not supported\n");
err = -EINVAL;
goto return_error;
}
@@ -1896,8 +1898,9 @@
nand_chip->ecc.bytes,
&ecclayout);
if (!nand_chip->ecc.priv) {
- pr_err("nand: error: unable to use s/w BCH library\n");
+ dev_err(&info->pdev->dev, "unable to use BCH library\n");
err = -EINVAL;
+ goto return_error;
}
break;
@@ -1959,7 +1962,7 @@
nand_chip->ecc.bytes,
&ecclayout);
if (!nand_chip->ecc.priv) {
- pr_err("nand: error: unable to use s/w BCH library\n");
+ dev_err(&info->pdev->dev, "unable to use BCH library\n");
err = -EINVAL;
goto return_error;
}
@@ -2026,7 +2029,7 @@
ecclayout->eccpos[ecclayout->eccbytes - 1] + 1;
break;
default:
- pr_err("nand: error: invalid or unsupported ECC scheme\n");
+ dev_err(&info->pdev->dev, "invalid or unsupported ECC scheme\n");
err = -EINVAL;
goto return_error;
}
@@ -2038,8 +2041,9 @@
ecclayout->oobfree->length = mtd->oobsize - ecclayout->oobfree->offset;
/* check if NAND device's OOB is enough to store ECC signatures */
if (mtd->oobsize < (ecclayout->eccbytes + BADBLOCK_MARKER_LENGTH)) {
- pr_err("not enough OOB bytes required = %d, available=%d\n",
- ecclayout->eccbytes, mtd->oobsize);
+ dev_err(&info->pdev->dev,
+ "not enough OOB bytes required = %d, available=%d\n",
+ ecclayout->eccbytes, mtd->oobsize);
err = -EINVAL;
goto return_error;
}