mac80211: adding 802.11n configuration flows
This patch configures the 802.11n mode of operation
internally in ieee80211_conf structure and in the low-level
driver as well (through op conf_ht).
It does not include AP configuration flows.
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
diff --git a/net/mac80211/ieee80211.c b/net/mac80211/ieee80211.c
index 4f8b665..d6a97a6 100644
--- a/net/mac80211/ieee80211.c
+++ b/net/mac80211/ieee80211.c
@@ -34,6 +34,8 @@
#include "debugfs.h"
#include "debugfs_netdev.h"
+#define SUPP_MCS_SET_LEN 16
+
/*
* For seeing transmitted packets on monitor interfaces
* we have a radiotap header too.
@@ -563,6 +565,55 @@
return ret;
}
+/**
+ * ieee80211_hw_config_ht should be used only after legacy configuration
+ * has been determined, as ht configuration depends upon the hardware's
+ * HT abilities for a _specific_ band.
+ */
+int ieee80211_hw_config_ht(struct ieee80211_local *local, int enable_ht,
+ struct ieee80211_ht_info *req_ht_cap,
+ struct ieee80211_ht_bss_info *req_bss_cap)
+{
+ struct ieee80211_conf *conf = &local->hw.conf;
+ struct ieee80211_hw_mode *mode = conf->mode;
+ int i;
+
+ /* HT is not supported */
+ if (!mode->ht_info.ht_supported) {
+ conf->flags &= ~IEEE80211_CONF_SUPPORT_HT_MODE;
+ return -EOPNOTSUPP;
+ }
+
+ /* disable HT */
+ if (!enable_ht) {
+ conf->flags &= ~IEEE80211_CONF_SUPPORT_HT_MODE;
+ } else {
+ conf->flags |= IEEE80211_CONF_SUPPORT_HT_MODE;
+ conf->ht_conf.cap = req_ht_cap->cap & mode->ht_info.cap;
+ conf->ht_conf.cap &= ~(IEEE80211_HT_CAP_MIMO_PS);
+ conf->ht_conf.cap |=
+ mode->ht_info.cap & IEEE80211_HT_CAP_MIMO_PS;
+ conf->ht_bss_conf.primary_channel =
+ req_bss_cap->primary_channel;
+ conf->ht_bss_conf.bss_cap = req_bss_cap->bss_cap;
+ conf->ht_bss_conf.bss_op_mode = req_bss_cap->bss_op_mode;
+ for (i = 0; i < SUPP_MCS_SET_LEN; i++)
+ conf->ht_conf.supp_mcs_set[i] =
+ mode->ht_info.supp_mcs_set[i] &
+ req_ht_cap->supp_mcs_set[i];
+
+ /* In STA mode, this gives us indication
+ * to the AP's mode of operation */
+ conf->ht_conf.ht_supported = 1;
+ conf->ht_conf.ampdu_factor = req_ht_cap->ampdu_factor;
+ conf->ht_conf.ampdu_density = req_ht_cap->ampdu_density;
+ }
+
+ local->ops->conf_ht(local_to_hw(local), &local->hw.conf);
+
+ return 0;
+}
+
void ieee80211_erp_info_change_notify(struct net_device *dev, u8 changes)
{
struct ieee80211_local *local = wdev_priv(dev->ieee80211_ptr);