mtd: m25p80: Add dual read support
Add support for Dual SPI read transfers, which is supported by some
Spansion SPI FLASHes.
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
diff --git a/drivers/mtd/devices/m25p80.c b/drivers/mtd/devices/m25p80.c
index ad19139..73bf661 100644
--- a/drivers/mtd/devices/m25p80.c
+++ b/drivers/mtd/devices/m25p80.c
@@ -41,7 +41,8 @@
#define OPCODE_WRSR 0x01 /* Write status register 1 byte */
#define OPCODE_NORM_READ 0x03 /* Read data bytes (low frequency) */
#define OPCODE_FAST_READ 0x0b /* Read data bytes (high frequency) */
-#define OPCODE_QUAD_READ 0x6b /* Read data bytes */
+#define OPCODE_DUAL_READ 0x3b /* Read data bytes (Dual SPI) */
+#define OPCODE_QUAD_READ 0x6b /* Read data bytes (Quad SPI) */
#define OPCODE_PP 0x02 /* Page program (up to 256 bytes) */
#define OPCODE_BE_4K 0x20 /* Erase 4KiB block */
#define OPCODE_BE_4K_PMC 0xd7 /* Erase 4KiB block on PMC chips */
@@ -54,7 +55,8 @@
/* 4-byte address opcodes - used on Spansion and some Macronix flashes. */
#define OPCODE_NORM_READ_4B 0x13 /* Read data bytes (low frequency) */
#define OPCODE_FAST_READ_4B 0x0c /* Read data bytes (high frequency) */
-#define OPCODE_QUAD_READ_4B 0x6c /* Read data bytes */
+#define OPCODE_DUAL_READ_4B 0x3c /* Read data bytes (Dual SPI) */
+#define OPCODE_QUAD_READ_4B 0x6c /* Read data bytes (Quad SPI) */
#define OPCODE_PP_4B 0x12 /* Page program (up to 256 bytes) */
#define OPCODE_SE_4B 0xdc /* Sector erase (usually 64KiB) */
@@ -95,6 +97,7 @@
enum read_type {
M25P80_NORMAL = 0,
M25P80_FAST,
+ M25P80_DUAL,
M25P80_QUAD,
};
@@ -479,6 +482,7 @@
{
switch (flash->flash_read) {
case M25P80_FAST:
+ case M25P80_DUAL:
case M25P80_QUAD:
return 1;
case M25P80_NORMAL:
@@ -492,6 +496,8 @@
static inline unsigned int m25p80_rx_nbits(const struct m25p *flash)
{
switch (flash->flash_read) {
+ case M25P80_DUAL:
+ return 2;
case M25P80_QUAD:
return 4;
default:
@@ -855,7 +861,8 @@
#define SST_WRITE 0x04 /* use SST byte programming */
#define M25P_NO_FR 0x08 /* Can't do fastread */
#define SECT_4K_PMC 0x10 /* OPCODE_BE_4K_PMC works uniformly */
-#define M25P80_QUAD_READ 0x20 /* Flash supports Quad Read */
+#define M25P80_DUAL_READ 0x20 /* Flash supports Dual Read */
+#define M25P80_QUAD_READ 0x40 /* Flash supports Quad Read */
};
#define INFO(_jedec_id, _ext_id, _sector_size, _n_sectors, _flags) \
@@ -1226,7 +1233,7 @@
if (info->flags & M25P_NO_FR)
flash->flash_read = M25P80_NORMAL;
- /* Quad-read mode takes precedence over fast/normal */
+ /* Quad/Dual-read mode takes precedence over fast/normal */
if (spi->mode & SPI_RX_QUAD && info->flags & M25P80_QUAD_READ) {
ret = set_quad_mode(flash, info->jedec_id);
if (ret) {
@@ -1234,6 +1241,8 @@
return ret;
}
flash->flash_read = M25P80_QUAD;
+ } else if (spi->mode & SPI_RX_DUAL && info->flags & M25P80_DUAL_READ) {
+ flash->flash_read = M25P80_DUAL;
}
/* Default commands */
@@ -1241,6 +1250,9 @@
case M25P80_QUAD:
flash->read_opcode = OPCODE_QUAD_READ;
break;
+ case M25P80_DUAL:
+ flash->read_opcode = OPCODE_DUAL_READ;
+ break;
case M25P80_FAST:
flash->read_opcode = OPCODE_FAST_READ;
break;
@@ -1265,6 +1277,9 @@
case M25P80_QUAD:
flash->read_opcode = OPCODE_QUAD_READ_4B;
break;
+ case M25P80_DUAL:
+ flash->read_opcode = OPCODE_DUAL_READ_4B;
+ break;
case M25P80_FAST:
flash->read_opcode = OPCODE_FAST_READ_4B;
break;