| menu "Board support" |
| |
| config SOLUTION_ENGINE |
| bool |
| |
| config SH_ALPHA_BOARD |
| bool |
| |
| config SH_DEVICE_TREE |
| bool "Board Described by Device Tree" |
| select OF |
| select OF_EARLY_FLATTREE |
| select CLKSRC_OF |
| select COMMON_CLK |
| select GENERIC_CALIBRATE_DELAY |
| help |
| Select Board Described by Device Tree to build a kernel that |
| does not hard-code any board-specific knowledge but instead uses |
| a device tree blob provided by the boot-loader. You must enable |
| drivers for any hardware you want to use separately. At this |
| time, only boards based on the open-hardware J-Core processors |
| have sufficient driver coverage to use this option; do not |
| select it if you are using original SuperH hardware. |
| |
| config SH_SOLUTION_ENGINE |
| bool "SolutionEngine" |
| select SOLUTION_ENGINE |
| select CPU_HAS_IPR_IRQ |
| depends on CPU_SUBTYPE_SH7705 || CPU_SUBTYPE_SH7709 || CPU_SUBTYPE_SH7710 || \ |
| CPU_SUBTYPE_SH7712 || CPU_SUBTYPE_SH7750 || CPU_SUBTYPE_SH7750S || \ |
| CPU_SUBTYPE_SH7750R |
| help |
| Select SolutionEngine if configuring for a Hitachi SH7705, SH7709, |
| SH7710, SH7712, SH7750, SH7750S or SH7750R evaluation board. |
| |
| config SH_7206_SOLUTION_ENGINE |
| bool "SolutionEngine7206" |
| select SOLUTION_ENGINE |
| depends on CPU_SUBTYPE_SH7206 |
| help |
| Select 7206 SolutionEngine if configuring for a Hitachi SH7206 |
| evaluation board. |
| |
| config SH_7619_SOLUTION_ENGINE |
| bool "SolutionEngine7619" |
| select SOLUTION_ENGINE |
| depends on CPU_SUBTYPE_SH7619 |
| help |
| Select 7619 SolutionEngine if configuring for a Hitachi SH7619 |
| evaluation board. |
| |
| config SH_7721_SOLUTION_ENGINE |
| bool "SolutionEngine7721" |
| select SOLUTION_ENGINE |
| depends on CPU_SUBTYPE_SH7721 |
| help |
| Select 7721 SolutionEngine if configuring for a Hitachi SH7721 |
| evaluation board. |
| |
| config SH_7722_SOLUTION_ENGINE |
| bool "SolutionEngine7722" |
| select SOLUTION_ENGINE |
| select GENERIC_IRQ_CHIP |
| select IRQ_DOMAIN |
| depends on CPU_SUBTYPE_SH7722 |
| help |
| Select 7722 SolutionEngine if configuring for a Hitachi SH772 |
| evaluation board. |
| |
| config SH_7724_SOLUTION_ENGINE |
| bool "SolutionEngine7724" |
| select SOLUTION_ENGINE |
| depends on CPU_SUBTYPE_SH7724 |
| select GPIOLIB |
| select SND_SOC_AK4642 if SND_SIMPLE_CARD |
| select REGULATOR_FIXED_VOLTAGE if REGULATOR |
| help |
| Select 7724 SolutionEngine if configuring for a Hitachi SH7724 |
| evaluation board. |
| |
| config SH_7751_SOLUTION_ENGINE |
| bool "SolutionEngine7751" |
| select SOLUTION_ENGINE |
| select CPU_HAS_IPR_IRQ |
| depends on CPU_SUBTYPE_SH7751 |
| help |
| Select 7751 SolutionEngine if configuring for a Hitachi SH7751 |
| evaluation board. |
| |
| config SH_7780_SOLUTION_ENGINE |
| bool "SolutionEngine7780" |
| select SOLUTION_ENGINE |
| select SYS_SUPPORTS_PCI |
| depends on CPU_SUBTYPE_SH7780 |
| help |
| Select 7780 SolutionEngine if configuring for a Renesas SH7780 |
| evaluation board. |
| |
| config SH_7343_SOLUTION_ENGINE |
| bool "SolutionEngine7343" |
| select SOLUTION_ENGINE |
| select GENERIC_IRQ_CHIP |
| select IRQ_DOMAIN |
| depends on CPU_SUBTYPE_SH7343 |
| help |
| Select 7343 SolutionEngine if configuring for a Hitachi |
| SH7343 (SH-Mobile 3AS) evaluation board. |
| |
| config SH_HP6XX |
| bool "HP6XX" |
| select SYS_SUPPORTS_APM_EMULATION |
| select HD6446X_SERIES |
| depends on CPU_SUBTYPE_SH7709 |
| help |
| Select HP6XX if configuring for a HP jornada HP6xx. |
| More information (hardware only) at |
| <http://www.hp.com/jornada/>. |
| |
| config SH_DREAMCAST |
| bool "Dreamcast" |
| select SYS_SUPPORTS_PCI |
| depends on CPU_SUBTYPE_SH7091 |
| help |
| Select Dreamcast if configuring for a SEGA Dreamcast. |
| More information at <http://www.linux-sh.org> |
| |
| config SH_SH03 |
| bool "Interface CTP/PCI-SH03" |
| depends on CPU_SUBTYPE_SH7751 |
| select CPU_HAS_IPR_IRQ |
| select SYS_SUPPORTS_PCI |
| help |
| CTP/PCI-SH03 is a CPU module computer that is produced |
| by Interface Corporation. |
| More information at <http://www.interface.co.jp> |
| |
| config SH_SECUREEDGE5410 |
| bool "SecureEdge5410" |
| depends on CPU_SUBTYPE_SH7751R |
| select CPU_HAS_IPR_IRQ |
| select SYS_SUPPORTS_PCI |
| help |
| Select SecureEdge5410 if configuring for a SnapGear SH board. |
| This includes both the OEM SecureEdge products as well as the |
| SME product line. |
| |
| config SH_RTS7751R2D |
| bool "RTS7751R2D" |
| depends on CPU_SUBTYPE_SH7751R |
| select SYS_SUPPORTS_PCI |
| select IO_TRAPPED if MMU |
| help |
| Select RTS7751R2D if configuring for a Renesas Technology |
| Sales SH-Graphics board. |
| |
| config SH_RSK |
| bool "Renesas Starter Kit" |
| depends on CPU_SUBTYPE_SH7201 || CPU_SUBTYPE_SH7203 || \ |
| CPU_SUBTYPE_SH7264 || CPU_SUBTYPE_SH7269 |
| select REGULATOR_FIXED_VOLTAGE if REGULATOR |
| help |
| Select this option if configuring for any of the RSK+ MCU |
| evaluation platforms. |
| |
| config SH_SDK7780 |
| bool "SDK7780R3" |
| depends on CPU_SUBTYPE_SH7780 |
| select SYS_SUPPORTS_PCI |
| help |
| Select SDK7780 if configuring for a Renesas SH7780 SDK7780R3 |
| evaluation board. |
| |
| config SH_SDK7786 |
| bool "SDK7786" |
| depends on CPU_SUBTYPE_SH7786 |
| select SYS_SUPPORTS_PCI |
| select NO_IOPORT_MAP if !PCI |
| select HAVE_SRAM_POOL |
| select REGULATOR_FIXED_VOLTAGE if REGULATOR |
| help |
| Select SDK7786 if configuring for a Renesas Technology Europe |
| SH7786-65nm board. |
| |
| config SH_HIGHLANDER |
| bool "Highlander" |
| depends on CPU_SUBTYPE_SH7780 || CPU_SUBTYPE_SH7785 |
| select SYS_SUPPORTS_PCI |
| select IO_TRAPPED if MMU |
| |
| config SH_SH7757LCR |
| bool "SH7757LCR" |
| depends on CPU_SUBTYPE_SH7757 |
| select GPIOLIB |
| select REGULATOR_FIXED_VOLTAGE if REGULATOR |
| |
| config SH_SH7785LCR |
| bool "SH7785LCR" |
| depends on CPU_SUBTYPE_SH7785 |
| select SYS_SUPPORTS_PCI |
| |
| config SH_SH7785LCR_29BIT_PHYSMAPS |
| bool "SH7785LCR 29bit physmaps" |
| depends on SH_SH7785LCR && 29BIT |
| default y |
| help |
| This board has 2 physical memory maps. It can be changed with |
| DIP switch(S2-5). If you set the DIP switch for S2-5 = ON, |
| you can access all on-board device in 29bit address mode. |
| |
| config SH_SH7785LCR_PT |
| bool "SH7785LCR prototype board on 32-bit MMU mode" |
| depends on SH_SH7785LCR && 32BIT |
| default n |
| help |
| If you use prototype board, this option is enabled. |
| |
| config SH_URQUELL |
| bool "Urquell" |
| depends on CPU_SUBTYPE_SH7786 |
| select GPIOLIB |
| select SYS_SUPPORTS_PCI |
| select NO_IOPORT_MAP if !PCI |
| |
| config SH_MIGOR |
| bool "Migo-R" |
| depends on CPU_SUBTYPE_SH7722 |
| select GPIOLIB |
| select REGULATOR_FIXED_VOLTAGE if REGULATOR |
| help |
| Select Migo-R if configuring for the SH7722 Migo-R platform |
| by Renesas System Solutions Asia Pte. Ltd. |
| |
| config SH_AP325RXA |
| bool "AP-325RXA" |
| depends on CPU_SUBTYPE_SH7723 |
| select GPIOLIB |
| select REGULATOR_FIXED_VOLTAGE if REGULATOR |
| help |
| Renesas "AP-325RXA" support. |
| Compatible with ALGO SYSTEM CO.,LTD. "AP-320A" |
| |
| config SH_KFR2R09 |
| bool "KFR2R09" |
| depends on CPU_SUBTYPE_SH7724 |
| select GPIOLIB |
| select REGULATOR_FIXED_VOLTAGE if REGULATOR |
| help |
| "Kit For R2R for 2009" support. |
| |
| config SH_ECOVEC |
| bool "EcoVec" |
| depends on CPU_SUBTYPE_SH7724 |
| select GPIOLIB |
| select SND_SOC_DA7210 if SND_SIMPLE_CARD |
| select REGULATOR_FIXED_VOLTAGE if REGULATOR |
| help |
| Renesas "R0P7724LC0011/21RL (EcoVec)" support. |
| |
| config SH_SH7763RDP |
| bool "SH7763RDP" |
| depends on CPU_SUBTYPE_SH7763 |
| help |
| Select SH7763RDP if configuring for a Renesas SH7763 |
| evaluation board. |
| |
| config SH_ESPT |
| bool "ESPT" |
| depends on CPU_SUBTYPE_SH7763 |
| help |
| Select ESPT if configuring for a Renesas SH7763 |
| with gigabit ether evaluation board. |
| |
| config SH_EDOSK7705 |
| bool "EDOSK7705" |
| depends on CPU_SUBTYPE_SH7705 |
| |
| config SH_EDOSK7760 |
| bool "EDOSK7760" |
| depends on CPU_SUBTYPE_SH7760 |
| help |
| Select if configuring for a Renesas EDOSK7760 |
| evaluation board. |
| |
| config SH_SH4202_MICRODEV |
| bool "SH4-202 MicroDev" |
| depends on CPU_SUBTYPE_SH4_202 |
| help |
| Select SH4-202 MicroDev if configuring for a SuperH MicroDev board |
| with an SH4-202 CPU. |
| |
| config SH_LANDISK |
| bool "LANDISK" |
| depends on CPU_SUBTYPE_SH7751R |
| select SYS_SUPPORTS_PCI |
| help |
| I-O DATA DEVICE, INC. "LANDISK Series" support. |
| |
| config SH_TITAN |
| bool "TITAN" |
| depends on CPU_SUBTYPE_SH7751R |
| select CPU_HAS_IPR_IRQ |
| select SYS_SUPPORTS_PCI |
| help |
| Select Titan if you are configuring for a Nimble Microsystems |
| NetEngine NP51R. |
| |
| config SH_SHMIN |
| bool "SHMIN" |
| depends on CPU_SUBTYPE_SH7706 |
| select CPU_HAS_IPR_IRQ |
| help |
| Select SHMIN if configuring for the SHMIN board. |
| |
| config SH_LBOX_RE2 |
| bool "L-BOX RE2" |
| depends on CPU_SUBTYPE_SH7751R |
| select SYS_SUPPORTS_PCI |
| help |
| Select L-BOX RE2 if configuring for the NTT COMWARE L-BOX RE2. |
| |
| config SH_X3PROTO |
| bool "SH-X3 Prototype board" |
| depends on CPU_SUBTYPE_SHX3 |
| select NO_IOPORT_MAP if !PCI |
| select IRQ_DOMAIN |
| |
| config SH_MAGIC_PANEL_R2 |
| bool "Magic Panel R2" |
| depends on CPU_SUBTYPE_SH7720 |
| select GPIOLIB |
| select REGULATOR_FIXED_VOLTAGE if REGULATOR |
| help |
| Select Magic Panel R2 if configuring for Magic Panel R2. |
| |
| config SH_CAYMAN |
| bool "Hitachi Cayman" |
| depends on CPU_SUBTYPE_SH5_101 || CPU_SUBTYPE_SH5_103 |
| select SYS_SUPPORTS_PCI |
| select ARCH_MIGHT_HAVE_PC_SERIO |
| |
| config SH_POLARIS |
| bool "SMSC Polaris" |
| select CPU_HAS_IPR_IRQ |
| select REGULATOR_FIXED_VOLTAGE if REGULATOR |
| depends on CPU_SUBTYPE_SH7709 |
| help |
| Select if configuring for an SMSC Polaris development board |
| |
| config SH_SH2007 |
| bool "SH-2007 board" |
| select NO_IOPORT_MAP |
| select REGULATOR_FIXED_VOLTAGE if REGULATOR |
| depends on CPU_SUBTYPE_SH7780 |
| help |
| SH-2007 is a single-board computer based around SH7780 chip |
| intended for embedded applications. |
| It has an Ethernet interface (SMC9118), direct connected |
| Compact Flash socket, two serial ports and PC-104 bus. |
| More information at <http://sh2000.sh-linux.org>. |
| |
| config SH_APSH4A3A |
| bool "AP-SH4A-3A" |
| select SH_ALPHA_BOARD |
| select REGULATOR_FIXED_VOLTAGE if REGULATOR |
| depends on CPU_SUBTYPE_SH7785 |
| help |
| Select AP-SH4A-3A if configuring for an ALPHAPROJECT AP-SH4A-3A. |
| |
| config SH_APSH4AD0A |
| bool "AP-SH4AD-0A" |
| select SH_ALPHA_BOARD |
| select SYS_SUPPORTS_PCI |
| select REGULATOR_FIXED_VOLTAGE if REGULATOR |
| depends on CPU_SUBTYPE_SH7786 |
| help |
| Select AP-SH4AD-0A if configuring for an ALPHAPROJECT AP-SH4AD-0A. |
| |
| source "arch/sh/boards/mach-r2d/Kconfig" |
| source "arch/sh/boards/mach-highlander/Kconfig" |
| source "arch/sh/boards/mach-sdk7780/Kconfig" |
| source "arch/sh/boards/mach-migor/Kconfig" |
| source "arch/sh/boards/mach-rsk/Kconfig" |
| |
| if SH_MAGIC_PANEL_R2 |
| |
| menu "Magic Panel R2 options" |
| |
| config SH_MAGIC_PANEL_R2_VERSION |
| int "Magic Panel R2 Version" |
| default "3" |
| help |
| Set the version of the Magic Panel R2 |
| |
| endmenu |
| |
| endif |
| |
| endmenu |