diff --git a/drivers/scsi/mvsas/mv_64xx.c b/drivers/scsi/mvsas/mv_64xx.c
index bc75ba7..dec5f96 100644
--- a/drivers/scsi/mvsas/mv_64xx.c
+++ b/drivers/scsi/mvsas/mv_64xx.c
@@ -33,7 +33,6 @@
 	u32 reg;
 	struct mvs_phy *phy = &mvi->phy[i];
 
-	/* TODO check & save device type */
 	reg = mr32(MVS_GBL_PORT_TYPE);
 	phy->phy_type &= ~(PORT_TYPE_SAS | PORT_TYPE_SATA);
 	if (reg & MODE_SAS_SATA & (1 << i))
@@ -63,7 +62,6 @@
 	mvs_phy_hacks(mvi);
 
 	if (!(mvi->flags & MVF_FLAG_SOC)) {
-		/* TEST - for phy decoding error, adjust voltage levels */
 		for (i = 0; i < MVS_SOC_PORTS; i++) {
 			mvs_write_port_vsr_addr(mvi, i, VSR_PHY_MODE8);
 			mvs_write_port_vsr_data(mvi, i, 0x2F0);
@@ -375,13 +373,7 @@
 		mvs_update_phyinfo(mvi, i, 1);
 	}
 
-	/* FIXME: update wide port bitmaps */
-
 	/* little endian for open address and command table, etc. */
-	/*
-	 * it seems that ( from the spec ) turning on big-endian won't
-	 * do us any good on big-endian machines, need further confirmation
-	 */
 	cctl = mr32(MVS_CTL);
 	cctl |= CCTL_ENDIAN_CMD;
 	cctl |= CCTL_ENDIAN_DATA;
@@ -394,8 +386,8 @@
 	tmp |= PCS_CMD_RST;
 	tmp &= ~PCS_SELF_CLEAR;
 	mw32(MVS_PCS, tmp);
-	/* interrupt coalescing may cause missing HW interrput in some case,
-	 * and the max count is 0x1ff, while our max slot is 0x200,
+	/*
+	 * the max count is 0x1ff, while our max slot is 0x200,
 	 * it will make count 0.
 	 */
 	tmp = 0;
@@ -632,7 +624,6 @@
 {
 	u32 tmp;
 	struct mvs_phy *phy = &mvi->phy[i];
-	/* workaround for HW phy decoding error on 1.5g disk drive */
 	mvs_write_port_vsr_addr(mvi, i, VSR_PHY_MODE6);
 	tmp = mvs_read_port_vsr_data(mvi, i);
 	if (((phy->phy_status & PHY_NEG_SPP_PHYS_LINK_RATE_MASK) >>
@@ -765,8 +756,8 @@
 {
 	void __iomem *regs = mvi->regs;
 	u32 tmp = 0;
-	/* interrupt coalescing may cause missing HW interrput in some case,
-	 * and the max count is 0x1ff, while our max slot is 0x200,
+	/*
+	 * the max count is 0x1ff, while our max slot is 0x200,
 	 * it will make count 0.
 	 */
 	if (time == 0) {
diff --git a/drivers/scsi/mvsas/mv_94xx.c b/drivers/scsi/mvsas/mv_94xx.c
index 1276e49..f4a995c 100644
--- a/drivers/scsi/mvsas/mv_94xx.c
+++ b/drivers/scsi/mvsas/mv_94xx.c
@@ -460,13 +460,7 @@
 		mvs_update_phyinfo(mvi, i, 1);
 	}
 
-	/* FIXME: update wide port bitmaps */
-
 	/* little endian for open address and command table, etc. */
-	/*
-	 * it seems that ( from the spec ) turning on big-endian won't
-	 * do us any good on big-endian machines, need further confirmation
-	 */
 	cctl = mr32(MVS_CTL);
 	cctl |= CCTL_ENDIAN_CMD;
 	cctl &= ~CCTL_ENDIAN_OPEN;
@@ -478,8 +472,8 @@
 	tmp |= PCS_CMD_RST;
 	tmp &= ~PCS_SELF_CLEAR;
 	mw32(MVS_PCS, tmp);
-	/* interrupt coalescing may cause missing HW interrput in some case,
-	 * and the max count is 0x1ff, while our max slot is 0x200,
+	/*
+	 * the max count is 0x1ff, while our max slot is 0x200,
 	 * it will make count 0.
 	 */
 	tmp = 0;
@@ -488,6 +482,7 @@
 	else
 		mw32(MVS_INT_COAL, MVS_CHIP_SLOT_SZ | COAL_EN);
 
+	/* default interrupt coalescing time is 128us */
 	tmp = 0x10000 | interrupt_coalescing;
 	mw32(MVS_INT_COAL_TMOUT, tmp);
 
@@ -745,7 +740,7 @@
 {
 	u32 phy_st;
 	phy_st = mvs_read_phy_ctl(mvi, i);
-	if (phy_st & PHY_READY_MASK)	/* phy ready */
+	if (phy_st & PHY_READY_MASK)
 		return 1;
 	return 0;
 }
@@ -770,7 +765,6 @@
 	int i;
 	u32 id_frame[7];
 
-	/* mvs_hexdump(28, (u8 *)id_frame, 0); */
 	for (i = 0; i < 7; i++) {
 		mvs_write_port_cfg_addr(mvi, port_id,
 					CONFIG_ATT_ID_FRAME0 + i * 4);
@@ -778,7 +772,6 @@
 		mv_dprintk("94xx phy %d atta frame %d %x.\n",
 			port_id + mvi->id * mvi->chip->n_phy, i, id_frame[i]);
 	}
-	/* mvs_hexdump(28, (u8 *)id_frame, 0); */
 	memcpy(id, id_frame, 28);
 }
 
@@ -962,8 +955,8 @@
 {
 	void __iomem *regs = mvi->regs;
 	u32 tmp = 0;
-	/* interrupt coalescing may cause missing HW interrput in some case,
-	 * and the max count is 0x1ff, while our max slot is 0x200,
+	/*
+	 * the max count is 0x1ff, while our max slot is 0x200,
 	 * it will make count 0.
 	 */
 	if (time == 0) {
diff --git a/drivers/scsi/mvsas/mv_94xx.h b/drivers/scsi/mvsas/mv_94xx.h
index d8c12e0..8f7eb4f 100644
--- a/drivers/scsi/mvsas/mv_94xx.h
+++ b/drivers/scsi/mvsas/mv_94xx.h
@@ -121,18 +121,18 @@
 
 /*  SAS/SATA Vendor Specific Port Registers */
 enum sas_sata_vsp_regs {
-	VSR_PHY_STAT		= 0x00 * 4, /* Phy Status */
-	VSR_PHY_MODE1		= 0x01 * 4, /* phy tx */
-	VSR_PHY_MODE2		= 0x02 * 4, /* tx scc */
-	VSR_PHY_MODE3		= 0x03 * 4, /* pll */
-	VSR_PHY_MODE4		= 0x04 * 4, /* VCO */
-	VSR_PHY_MODE5		= 0x05 * 4, /* Rx */
-	VSR_PHY_MODE6		= 0x06 * 4, /* CDR */
-	VSR_PHY_MODE7		= 0x07 * 4, /* Impedance */
-	VSR_PHY_MODE8		= 0x08 * 4, /* Voltage */
-	VSR_PHY_MODE9		= 0x09 * 4, /* Test */
-	VSR_PHY_MODE10		= 0x0A * 4, /* Power */
-	VSR_PHY_MODE11		= 0x0B * 4, /* Phy Mode */
+	VSR_PHY_STAT		= 0x00 * 4, /* Phy Interrupt Status */
+	VSR_PHY_MODE1		= 0x01 * 4, /* phy Interrupt Enable */
+	VSR_PHY_MODE2		= 0x02 * 4, /* Phy Configuration */
+	VSR_PHY_MODE3		= 0x03 * 4, /* Phy Status */
+	VSR_PHY_MODE4		= 0x04 * 4, /* Phy Counter 0 */
+	VSR_PHY_MODE5		= 0x05 * 4, /* Phy Counter 1 */
+	VSR_PHY_MODE6		= 0x06 * 4, /* Event Counter Control */
+	VSR_PHY_MODE7		= 0x07 * 4, /* Event Counter Select */
+	VSR_PHY_MODE8		= 0x08 * 4, /* Event Counter 0 */
+	VSR_PHY_MODE9		= 0x09 * 4, /* Event Counter 1 */
+	VSR_PHY_MODE10		= 0x0A * 4, /* Event Counter 2 */
+	VSR_PHY_MODE11		= 0x0B * 4, /* Event Counter 3 */
 	VSR_PHY_ACT_LED		= 0x0C * 4, /* Activity LED control */
 
 	VSR_PHY_FFE_CONTROL	= 0x10C,
diff --git a/drivers/scsi/mvsas/mv_chips.h b/drivers/scsi/mvsas/mv_chips.h
index 0a11bc7..bcc4080 100644
--- a/drivers/scsi/mvsas/mv_chips.h
+++ b/drivers/scsi/mvsas/mv_chips.h
@@ -164,7 +164,6 @@
 {
 	u32 tmp;
 
-	/* workaround for SATA R-ERR, to ignore phy glitch */
 	tmp = mvs_cr32(mvi, CMD_PHY_TIMER);
 	tmp &= ~(1 << 9);
 	tmp |= (1 << 10);
@@ -179,7 +178,6 @@
 	tmp |= 0x3fff;
 	mvs_cw32(mvi, CMD_SAS_CTL0, tmp);
 
-	/* workaround for WDTIMEOUT , set to 550 ms */
 	mvs_cw32(mvi, CMD_WD_TIMER, 0x7a0000);
 
 	/* not to halt for different port op during wideport link change */
diff --git a/drivers/scsi/mvsas/mv_defs.h b/drivers/scsi/mvsas/mv_defs.h
index 1927e1bb..dec7cad 100644
--- a/drivers/scsi/mvsas/mv_defs.h
+++ b/drivers/scsi/mvsas/mv_defs.h
@@ -160,7 +160,7 @@
 	TXQ_CMD_SSP		= 1,		/* SSP protocol */
 	TXQ_CMD_SMP		= 2,		/* SMP protocol */
 	TXQ_CMD_STP		= 3,		/* STP/SATA protocol */
-	TXQ_CMD_SSP_FREE_LIST	= 4,		/* add to SSP targ free list */
+	TXQ_CMD_SSP_FREE_LIST	= 4,		/* add to SSP target free list */
 	TXQ_CMD_SLOT_RESET	= 7,		/* reset command slot */
 	TXQ_MODE_I		= (1U << 28),	/* mode: 0=target,1=initiator */
 	TXQ_MODE_TARGET 	= 0,
diff --git a/drivers/scsi/mvsas/mv_init.c b/drivers/scsi/mvsas/mv_init.c
index b28ee5b..cf4aaa9 100644
--- a/drivers/scsi/mvsas/mv_init.c
+++ b/drivers/scsi/mvsas/mv_init.c
@@ -405,7 +405,6 @@
 	return NULL;
 }
 
-/* move to PCI layer or libata core? */
 static int pci_go_64(struct pci_dev *pdev)
 {
 	int rc;
diff --git a/drivers/scsi/mvsas/mv_sas.c b/drivers/scsi/mvsas/mv_sas.c
index 31ca8fe..4958fef 100644
--- a/drivers/scsi/mvsas/mv_sas.c
+++ b/drivers/scsi/mvsas/mv_sas.c
@@ -102,7 +102,6 @@
 
 }
 
-/* FIXME */
 int mvs_find_dev_phyno(struct domain_device *dev, int *phyno)
 {
 	unsigned long i = 0, j = 0, n = 0, num = 0;
@@ -177,7 +176,6 @@
 	}
 }
 
-/* FIXME: locking? */
 int mvs_phy_control(struct asd_sas_phy *sas_phy, enum phy_func func,
 			void *funcdata)
 {
@@ -504,11 +502,8 @@
 			flags |= MCH_ATAPI;
 	}
 
-	/* FIXME: fill in port multiplier number */
-
 	hdr->flags = cpu_to_le32(flags);
 
-	/* FIXME: the low order order 5 bits for the TAG if enable NCQ */
 	if (task->ata_task.use_ncq && mvs_get_ncq_tag(task, &hdr_tag))
 		task->ata_task.fis.sector_count |= (u8) (hdr_tag << 3);
 	else
@@ -552,9 +547,6 @@
 	buf_tmp_dma += i;
 
 	/* region 4: status buffer (larger the PRD, smaller this buf) ****** */
-	/* FIXME: probably unused, for SATA.  kept here just in case
-	 * we get a STP/SATA error information record
-	 */
 	slot->response = buf_tmp;
 	hdr->status_buf = cpu_to_le64(buf_tmp_dma);
 	if (mvi->flags & MVF_FLAG_SOC)
@@ -1126,7 +1118,6 @@
 	MVS_CHIP_DISP->write_port_cfg_addr(mvi, i, PHYR_SATA_SIG0);
 	s[0] = cpu_to_le32(MVS_CHIP_DISP->read_port_cfg_data(mvi, i));
 
-	/* Workaround: take some ATAPI devices for ATA */
 	if (((s[1] & 0x00FFFFFF) == 0x00EB1401) && (*(u8 *)&s[3] == 0x01))
 		s[1] = 0x00EB1401 | (*((u8 *)&s[1] + 3) & 0x10);
 
@@ -1433,7 +1424,6 @@
 	complete(&task->completion);
 }
 
-/* XXX */
 #define MVS_TASK_TIMEOUT 20
 static int mvs_exec_internal_tmf_task(struct domain_device *dev,
 			void *parameter, u32 para_len, struct mvs_tmf_task *tmf)
@@ -1577,7 +1567,6 @@
 	mv_printk("%s for device[%x]:rc= %d\n",
 		__func__, mvi_dev->device_id, rc);
 
-	/* housekeeper */
 	spin_lock_irqsave(&mvi->lock, flags);
 	mvs_release_task(mvi, dev);
 	spin_unlock_irqrestore(&mvi->lock, flags);
@@ -1681,7 +1670,6 @@
 
 	} else if (task->task_proto & SAS_PROTOCOL_SATA ||
 		task->task_proto & SAS_PROTOCOL_STP) {
-		/* to do free register_set */
 		if (SATA_DEV == dev->dev_type) {
 			struct mvs_slot_info *slot = task->lldd_task;
 			u32 slot_idx = (u32)(slot - mvi->slot_info);
@@ -1901,6 +1889,7 @@
 		return -1;
 	}
 
+	/* when no device attaching, go ahead and complete by error handling*/
 	if (unlikely(!mvi_dev || flags)) {
 		if (!mvi_dev)
 			mv_dprintk("port has not device.\n");
@@ -2017,7 +2006,6 @@
 		      struct domain_device *dev)
 {
 	int i, phyno[WIDE_PORT_MAX_PHY], num;
-	/* housekeeper */
 	num = mvs_find_dev_phyno(dev, phyno);
 	for (i = 0; i < num; i++)
 		mvs_do_release_task(mvi, phyno[i], dev);