spi: dw-mid: convert value of dma_width to enum dma_slave_buswidth
DMAEngine has a specific type to be used for bus width. This patch converts the
code to use the values of the specific type when configure DMA transfer.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
diff --git a/drivers/spi/spi-dw-mid.c b/drivers/spi/spi-dw-mid.c
index c8416ef..25c8fa7 100644
--- a/drivers/spi/spi-dw-mid.c
+++ b/drivers/spi/spi-dw-mid.c
@@ -100,6 +100,15 @@
dma_release_channel(dws->rxchan);
}
+static enum dma_slave_buswidth convert_dma_width(u32 dma_width) {
+ if (dma_width == 1)
+ return DMA_SLAVE_BUSWIDTH_1_BYTE;
+ else if (dma_width == 2)
+ return DMA_SLAVE_BUSWIDTH_2_BYTES;
+
+ return DMA_SLAVE_BUSWIDTH_UNDEFINED;
+}
+
/*
* dws->dma_chan_busy is set before the dma transfer starts, callback for tx
* channel will clear a corresponding bit.
@@ -126,7 +135,7 @@
txconf.dst_addr = dws->dma_addr;
txconf.dst_maxburst = LNW_DMA_MSIZE_16;
txconf.src_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES;
- txconf.dst_addr_width = dws->dma_width;
+ txconf.dst_addr_width = convert_dma_width(dws->dma_width);
txconf.device_fc = false;
dmaengine_slave_config(dws->txchan, &txconf);
@@ -175,7 +184,7 @@
rxconf.src_addr = dws->dma_addr;
rxconf.src_maxburst = LNW_DMA_MSIZE_16;
rxconf.dst_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES;
- rxconf.src_addr_width = dws->dma_width;
+ rxconf.src_addr_width = convert_dma_width(dws->dma_width);
rxconf.device_fc = false;
dmaengine_slave_config(dws->rxchan, &rxconf);
diff --git a/drivers/spi/spi-dw.c b/drivers/spi/spi-dw.c
index 950bc50..f3e4092 100644
--- a/drivers/spi/spi-dw.c
+++ b/drivers/spi/spi-dw.c
@@ -315,7 +315,6 @@
{
struct dw_spi *dws = spi_master_get_devdata(master);
struct chip_data *chip = spi_get_ctldata(spi);
- u8 bits = 0;
u8 imask = 0;
u8 cs_change = 0;
u16 txlevel = 0;
@@ -357,9 +356,14 @@
}
}
if (transfer->bits_per_word) {
- bits = transfer->bits_per_word;
- dws->n_bytes = dws->dma_width = bits >> 3;
- cr0 = (bits - 1)
+ if (transfer->bits_per_word == 8) {
+ dws->n_bytes = 1;
+ dws->dma_width = 1;
+ } else if (transfer->bits_per_word == 16) {
+ dws->n_bytes = 2;
+ dws->dma_width = 2;
+ }
+ cr0 = (transfer->bits_per_word - 1)
| (chip->type << SPI_FRF_OFFSET)
| (spi->mode << SPI_MODE_OFFSET)
| (chip->tmode << SPI_TMOD_OFFSET);