phy: Add an mdio_device structure
Not all devices attached to an MDIO bus are phys. So add an
mdio_device structure to represent the generic parts of an mdio
device, and place this structure into the phy_device.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
diff --git a/drivers/net/phy/at803x.c b/drivers/net/phy/at803x.c
index 62361f8..b76ac09 100644
--- a/drivers/net/phy/at803x.c
+++ b/drivers/net/phy/at803x.c
@@ -190,7 +190,7 @@
static int at803x_probe(struct phy_device *phydev)
{
- struct device *dev = &phydev->dev;
+ struct device *dev = &phydev->mdio.dev;
struct at803x_priv *priv;
struct gpio_desc *gpiod_reset;
diff --git a/drivers/net/phy/bcm87xx.c b/drivers/net/phy/bcm87xx.c
index 71b491c..e536e30 100644
--- a/drivers/net/phy/bcm87xx.c
+++ b/drivers/net/phy/bcm87xx.c
@@ -40,10 +40,10 @@
const __be32 *paddr_end;
int len, ret;
- if (!phydev->dev.of_node)
+ if (!phydev->mdio.dev.of_node)
return 0;
- paddr = of_get_property(phydev->dev.of_node,
+ paddr = of_get_property(phydev->mdio.dev.of_node,
"broadcom,c45-reg-init", &len);
if (!paddr)
return 0;
diff --git a/drivers/net/phy/dp83640.c b/drivers/net/phy/dp83640.c
index 47b7117..39da6fc 100644
--- a/drivers/net/phy/dp83640.c
+++ b/drivers/net/phy/dp83640.c
@@ -220,9 +220,10 @@
#define BROADCAST_ADDR 31
-static inline int broadcast_write(struct mii_bus *bus, u32 regnum, u16 val)
+static inline int broadcast_write(struct phy_device *phydev, u32 regnum,
+ u16 val)
{
- return mdiobus_write(bus, BROADCAST_ADDR, regnum, val);
+ return mdiobus_write(phydev->mdio.bus, BROADCAST_ADDR, regnum, val);
}
/* Caller must hold extreg_lock. */
@@ -232,7 +233,7 @@
int val;
if (dp83640->clock->page != page) {
- broadcast_write(phydev->bus, PAGESEL, page);
+ broadcast_write(phydev, PAGESEL, page);
dp83640->clock->page = page;
}
val = phy_read(phydev, regnum);
@@ -247,11 +248,11 @@
struct dp83640_private *dp83640 = phydev->priv;
if (dp83640->clock->page != page) {
- broadcast_write(phydev->bus, PAGESEL, page);
+ broadcast_write(phydev, PAGESEL, page);
dp83640->clock->page = page;
}
if (broadcast)
- broadcast_write(phydev->bus, regnum, val);
+ broadcast_write(phydev, regnum, val);
else
phy_write(phydev, regnum, val);
}
@@ -1039,7 +1040,7 @@
if (chosen_phy == -1 && !clock->chosen)
return 1;
- if (chosen_phy == phydev->addr)
+ if (chosen_phy == phydev->mdio.addr)
return 1;
return 0;
@@ -1103,10 +1104,10 @@
struct dp83640_private *dp83640;
int err = -ENOMEM, i;
- if (phydev->addr == BROADCAST_ADDR)
+ if (phydev->mdio.addr == BROADCAST_ADDR)
return 0;
- clock = dp83640_clock_get_bus(phydev->bus);
+ clock = dp83640_clock_get_bus(phydev->mdio.bus);
if (!clock)
goto no_clock;
@@ -1132,7 +1133,8 @@
if (choose_this_phy(clock, phydev)) {
clock->chosen = dp83640;
- clock->ptp_clock = ptp_clock_register(&clock->caps, &phydev->dev);
+ clock->ptp_clock = ptp_clock_register(&clock->caps,
+ &phydev->mdio.dev);
if (IS_ERR(clock->ptp_clock)) {
err = PTR_ERR(clock->ptp_clock);
goto no_register;
@@ -1158,7 +1160,7 @@
struct list_head *this, *next;
struct dp83640_private *tmp, *dp83640 = phydev->priv;
- if (phydev->addr == BROADCAST_ADDR)
+ if (phydev->mdio.addr == BROADCAST_ADDR)
return;
enable_status_frames(phydev, false);
diff --git a/drivers/net/phy/dp83867.c b/drivers/net/phy/dp83867.c
index e4c0b0c..74e4521 100644
--- a/drivers/net/phy/dp83867.c
+++ b/drivers/net/phy/dp83867.c
@@ -103,7 +103,7 @@
static int dp83867_of_init(struct phy_device *phydev)
{
struct dp83867_private *dp83867 = phydev->priv;
- struct device *dev = &phydev->dev;
+ struct device *dev = &phydev->mdio.dev;
struct device_node *of_node = dev->of_node;
int ret;
@@ -137,7 +137,7 @@
u16 val, delay;
if (!phydev->priv) {
- dp83867 = devm_kzalloc(&phydev->dev, sizeof(*dp83867),
+ dp83867 = devm_kzalloc(&phydev->mdio.dev, sizeof(*dp83867),
GFP_KERNEL);
if (!dp83867)
return -ENOMEM;
diff --git a/drivers/net/phy/fixed_phy.c b/drivers/net/phy/fixed_phy.c
index 0a1cde6..ab9c473 100644
--- a/drivers/net/phy/fixed_phy.c
+++ b/drivers/net/phy/fixed_phy.c
@@ -197,11 +197,11 @@
struct fixed_mdio_bus *fmb = &platform_fmb;
struct fixed_phy *fp;
- if (!phydev || !phydev->bus)
+ if (!phydev || !phydev->mdio.bus)
return -EINVAL;
list_for_each_entry(fp, &fmb->phys, node) {
- if (fp->addr == phydev->addr) {
+ if (fp->addr == phydev->mdio.addr) {
fp->link_update = link_update;
fp->phydev = phydev;
return 0;
@@ -219,11 +219,11 @@
struct fixed_mdio_bus *fmb = &platform_fmb;
struct fixed_phy *fp;
- if (!phydev || phydev->bus != fmb->mii_bus)
+ if (!phydev || phydev->mdio.bus != fmb->mii_bus)
return -EINVAL;
list_for_each_entry(fp, &fmb->phys, node) {
- if (fp->addr == phydev->addr) {
+ if (fp->addr == phydev->mdio.addr) {
#define _UPD(x) if (changed->x) \
fp->status.x = status->x
_UPD(link);
@@ -344,7 +344,7 @@
}
of_node_get(np);
- phy->dev.of_node = np;
+ phy->mdio.dev.of_node = np;
phy->is_pseudo_fixed_link = true;
switch (status->speed) {
diff --git a/drivers/net/phy/icplus.c b/drivers/net/phy/icplus.c
index 0dbc445..c12170d 100644
--- a/drivers/net/phy/icplus.c
+++ b/drivers/net/phy/icplus.c
@@ -53,43 +53,43 @@
if (full_reset_performed == 0) {
/* master reset */
- err = mdiobus_write(phydev->bus, 30, 0, 0x175c);
+ err = mdiobus_write(phydev->mdio.bus, 30, 0, 0x175c);
if (err < 0)
return err;
/* ensure no bus delays overlap reset period */
- err = mdiobus_read(phydev->bus, 30, 0);
+ err = mdiobus_read(phydev->mdio.bus, 30, 0);
/* data sheet specifies reset period is 2 msec */
mdelay(2);
/* enable IP175C mode */
- err = mdiobus_write(phydev->bus, 29, 31, 0x175c);
+ err = mdiobus_write(phydev->mdio.bus, 29, 31, 0x175c);
if (err < 0)
return err;
/* Set MII0 speed and duplex (in PHY mode) */
- err = mdiobus_write(phydev->bus, 29, 22, 0x420);
+ err = mdiobus_write(phydev->mdio.bus, 29, 22, 0x420);
if (err < 0)
return err;
/* reset switch ports */
for (i = 0; i < 5; i++) {
- err = mdiobus_write(phydev->bus, i,
+ err = mdiobus_write(phydev->mdio.bus, i,
MII_BMCR, BMCR_RESET);
if (err < 0)
return err;
}
for (i = 0; i < 5; i++)
- err = mdiobus_read(phydev->bus, i, MII_BMCR);
+ err = mdiobus_read(phydev->mdio.bus, i, MII_BMCR);
mdelay(2);
full_reset_performed = 1;
}
- if (phydev->addr != 4) {
+ if (phydev->mdio.addr != 4) {
phydev->state = PHY_RUNNING;
phydev->speed = SPEED_100;
phydev->duplex = DUPLEX_FULL;
@@ -184,7 +184,7 @@
static int ip175c_read_status(struct phy_device *phydev)
{
- if (phydev->addr == 4) /* WAN port */
+ if (phydev->mdio.addr == 4) /* WAN port */
genphy_read_status(phydev);
else
/* Don't need to read status for switch ports */
@@ -195,7 +195,7 @@
static int ip175c_config_aneg(struct phy_device *phydev)
{
- if (phydev->addr == 4) /* WAN port */
+ if (phydev->mdio.addr == 4) /* WAN port */
genphy_config_aneg(phydev);
return 0;
diff --git a/drivers/net/phy/marvell.c b/drivers/net/phy/marvell.c
index 50b5eac..f96c93c 100644
--- a/drivers/net/phy/marvell.c
+++ b/drivers/net/phy/marvell.c
@@ -300,10 +300,11 @@
const __be32 *paddr;
int len, i, saved_page, current_page, page_changed, ret;
- if (!phydev->dev.of_node)
+ if (!phydev->mdio.dev.of_node)
return 0;
- paddr = of_get_property(phydev->dev.of_node, "marvell,reg-init", &len);
+ paddr = of_get_property(phydev->mdio.dev.of_node,
+ "marvell,reg-init", &len);
if (!paddr || len < (4 * sizeof(*paddr)))
return 0;
@@ -1060,7 +1061,7 @@
{
struct marvell_priv *priv;
- priv = devm_kzalloc(&phydev->dev, sizeof(*priv), GFP_KERNEL);
+ priv = devm_kzalloc(&phydev->mdio.dev, sizeof(*priv), GFP_KERNEL);
if (!priv)
return -ENOMEM;
diff --git a/drivers/net/phy/mdio_bus.c b/drivers/net/phy/mdio_bus.c
index 05381d0..e5b1ccd 100644
--- a/drivers/net/phy/mdio_bus.c
+++ b/drivers/net/phy/mdio_bus.c
@@ -200,16 +200,16 @@
* the phy. This allows auto-probed pyh devices to be supplied with information
* passed in via DT.
*/
-static void of_mdiobus_link_phydev(struct mii_bus *mdio,
+static void of_mdiobus_link_phydev(struct mii_bus *bus,
struct phy_device *phydev)
{
- struct device *dev = &phydev->dev;
+ struct device *dev = &phydev->mdio.dev;
struct device_node *child;
- if (dev->of_node || !mdio->dev.of_node)
+ if (dev->of_node || !bus->dev.of_node)
return;
- for_each_available_child_of_node(mdio->dev.of_node, child) {
+ for_each_available_child_of_node(bus->dev.of_node, child) {
int addr;
int ret;
@@ -227,7 +227,7 @@
continue;
}
- if (addr == phydev->addr) {
+ if (addr == phydev->mdio.addr) {
dev->of_node = child;
return;
}
@@ -522,7 +522,7 @@
static bool mdio_bus_phy_may_suspend(struct phy_device *phydev)
{
- struct device_driver *drv = phydev->dev.driver;
+ struct device_driver *drv = phydev->mdio.dev.driver;
struct phy_driver *phydrv = to_phy_driver(drv);
struct net_device *netdev = phydev->attached_dev;
diff --git a/drivers/net/phy/micrel.c b/drivers/net/phy/micrel.c
index bf72365..b51505b 100644
--- a/drivers/net/phy/micrel.c
+++ b/drivers/net/phy/micrel.c
@@ -350,7 +350,7 @@
static int ksz9021_config_init(struct phy_device *phydev)
{
- const struct device *dev = &phydev->dev;
+ const struct device *dev = &phydev->mdio.dev;
const struct device_node *of_node = dev->of_node;
const struct device *dev_walker;
@@ -358,7 +358,7 @@
* properties in the MAC node. Walk up the tree of devices to
* find a device with an OF node.
*/
- dev_walker = &phydev->dev;
+ dev_walker = &phydev->mdio.dev;
do {
of_node = dev_walker->of_node;
dev_walker = dev_walker->parent;
@@ -471,7 +471,7 @@
static int ksz9031_config_init(struct phy_device *phydev)
{
- const struct device *dev = &phydev->dev;
+ const struct device *dev = &phydev->mdio.dev;
const struct device_node *of_node = dev->of_node;
static const char *clk_skews[2] = {"rxc-skew-ps", "txc-skew-ps"};
static const char *rx_data_skews[4] = {
@@ -630,12 +630,12 @@
static int kszphy_probe(struct phy_device *phydev)
{
const struct kszphy_type *type = phydev->drv->driver_data;
- const struct device_node *np = phydev->dev.of_node;
+ const struct device_node *np = phydev->mdio.dev.of_node;
struct kszphy_priv *priv;
struct clk *clk;
int ret;
- priv = devm_kzalloc(&phydev->dev, sizeof(*priv), GFP_KERNEL);
+ priv = devm_kzalloc(&phydev->mdio.dev, sizeof(*priv), GFP_KERNEL);
if (!priv)
return -ENOMEM;
@@ -658,7 +658,7 @@
priv->led_mode = -1;
}
- clk = devm_clk_get(&phydev->dev, "rmii-ref");
+ clk = devm_clk_get(&phydev->mdio.dev, "rmii-ref");
/* NOTE: clk may be NULL if building without CONFIG_HAVE_CLK */
if (!IS_ERR_OR_NULL(clk)) {
unsigned long rate = clk_get_rate(clk);
diff --git a/drivers/net/phy/microchip.c b/drivers/net/phy/microchip.c
index 99df5bc..5e34b49 100644
--- a/drivers/net/phy/microchip.c
+++ b/drivers/net/phy/microchip.c
@@ -68,7 +68,7 @@
static int lan88xx_probe(struct phy_device *phydev)
{
- struct device *dev = &phydev->dev;
+ struct device *dev = &phydev->mdio.dev;
struct lan88xx_priv *priv;
priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
@@ -89,7 +89,7 @@
static void lan88xx_remove(struct phy_device *phydev)
{
- struct device *dev = &phydev->dev;
+ struct device *dev = &phydev->mdio.dev;
struct lan88xx_priv *priv = phydev->priv;
if (priv)
diff --git a/drivers/net/phy/phy.c b/drivers/net/phy/phy.c
index 56c8dd8..8763bb2 100644
--- a/drivers/net/phy/phy.c
+++ b/drivers/net/phy/phy.c
@@ -319,7 +319,7 @@
{
u32 speed = ethtool_cmd_speed(cmd);
- if (cmd->phy_address != phydev->addr)
+ if (cmd->phy_address != phydev->mdio.addr)
return -EINVAL;
/* We make sure that we don't pass unsupported values in to the PHY */
@@ -375,7 +375,7 @@
cmd->port = PORT_BNC;
else
cmd->port = PORT_MII;
- cmd->phy_address = phydev->addr;
+ cmd->phy_address = phydev->mdio.addr;
cmd->transceiver = phy_is_internal(phydev) ?
XCVR_INTERNAL : XCVR_EXTERNAL;
cmd->autoneg = phydev->autoneg;
@@ -403,16 +403,17 @@
switch (cmd) {
case SIOCGMIIPHY:
- mii_data->phy_id = phydev->addr;
+ mii_data->phy_id = phydev->mdio.addr;
/* fall through */
case SIOCGMIIREG:
- mii_data->val_out = mdiobus_read(phydev->bus, mii_data->phy_id,
+ mii_data->val_out = mdiobus_read(phydev->mdio.bus,
+ mii_data->phy_id,
mii_data->reg_num);
return 0;
case SIOCSMIIREG:
- if (mii_data->phy_id == phydev->addr) {
+ if (mii_data->phy_id == phydev->mdio.addr) {
switch (mii_data->reg_num) {
case MII_BMCR:
if ((val & (BMCR_RESET | BMCR_ANENABLE)) == 0) {
@@ -445,10 +446,10 @@
}
}
- mdiobus_write(phydev->bus, mii_data->phy_id,
+ mdiobus_write(phydev->mdio.bus, mii_data->phy_id,
mii_data->reg_num, val);
- if (mii_data->phy_id == phydev->addr &&
+ if (mii_data->phy_id == phydev->mdio.addr &&
mii_data->reg_num == MII_BMCR &&
val & BMCR_RESET)
return phy_init_hw(phydev);
@@ -643,7 +644,7 @@
if (request_irq(phydev->irq, phy_interrupt, 0, "phy_interrupt",
phydev) < 0) {
pr_warn("%s: Can't get IRQ %d (PHY)\n",
- phydev->bus->name, phydev->irq);
+ phydev->mdio.bus->name, phydev->irq);
phydev->irq = PHY_POLL;
return 0;
}
@@ -1041,11 +1042,11 @@
int phy_read_mmd_indirect(struct phy_device *phydev, int prtad, int devad)
{
struct phy_driver *phydrv = phydev->drv;
- int addr = phydev->addr;
+ int addr = phydev->mdio.addr;
int value = -1;
if (!phydrv->read_mmd_indirect) {
- struct mii_bus *bus = phydev->bus;
+ struct mii_bus *bus = phydev->mdio.bus;
mutex_lock(&bus->mdio_lock);
mmd_phy_indirect(bus, prtad, devad, addr);
@@ -1079,10 +1080,10 @@
int devad, u32 data)
{
struct phy_driver *phydrv = phydev->drv;
- int addr = phydev->addr;
+ int addr = phydev->mdio.addr;
if (!phydrv->write_mmd_indirect) {
- struct mii_bus *bus = phydev->bus;
+ struct mii_bus *bus = phydev->mdio.bus;
mutex_lock(&bus->mdio_lock);
mmd_phy_indirect(bus, prtad, devad, addr);
diff --git a/drivers/net/phy/phy_device.c b/drivers/net/phy/phy_device.c
index 68fe573..01e5d52 100644
--- a/drivers/net/phy/phy_device.c
+++ b/drivers/net/phy/phy_device.c
@@ -43,7 +43,7 @@
void phy_device_free(struct phy_device *phydev)
{
- put_device(&phydev->dev);
+ put_device(&phydev->mdio.dev);
}
EXPORT_SYMBOL(phy_device_free);
@@ -65,7 +65,7 @@
/**
* phy_register_fixup - creates a new phy_fixup and adds it to the list
- * @bus_id: A string which matches phydev->dev.bus_id (or PHY_ANY_ID)
+ * @bus_id: A string which matches phydev->mdio.dev.bus_id (or PHY_ANY_ID)
* @phy_uid: Used to match against phydev->phy_id (the UID of the PHY)
* It can also be PHY_ANY_UID
* @phy_uid_mask: Applied to phydev->phy_id and fixup->phy_uid before
@@ -153,13 +153,19 @@
struct phy_c45_device_ids *c45_ids)
{
struct phy_device *dev;
+ struct mdio_device *mdiodev;
/* We allocate the device, and initialize the default values */
dev = kzalloc(sizeof(*dev), GFP_KERNEL);
if (!dev)
return ERR_PTR(-ENOMEM);
- dev->dev.release = phy_device_release;
+ mdiodev = &dev->mdio;
+ mdiodev->dev.release = phy_device_release;
+ mdiodev->dev.parent = &bus->dev;
+ mdiodev->dev.bus = &mdio_bus_type;
+ mdiodev->bus = bus;
+ mdiodev->addr = addr;
dev->speed = 0;
dev->duplex = -1;
@@ -171,15 +177,11 @@
dev->autoneg = AUTONEG_ENABLE;
dev->is_c45 = is_c45;
- dev->addr = addr;
dev->phy_id = phy_id;
if (c45_ids)
dev->c45_ids = *c45_ids;
- dev->bus = bus;
- dev->dev.parent = &bus->dev;
- dev->dev.bus = &mdio_bus_type;
dev->irq = bus->irq ? bus->irq[addr] : PHY_POLL;
- dev_set_name(&dev->dev, PHY_ID_FMT, bus->id, addr);
+ dev_set_name(&mdiodev->dev, PHY_ID_FMT, bus->id, addr);
dev->state = PHY_DOWN;
@@ -199,7 +201,7 @@
*/
request_module(MDIO_MODULE_PREFIX MDIO_ID_FMT, MDIO_ID_ARGS(phy_id));
- device_initialize(&dev->dev);
+ device_initialize(&mdiodev->dev);
return dev;
}
@@ -382,27 +384,27 @@
int err;
/* Don't register a phy if one is already registered at this address */
- if (phydev->bus->phy_map[phydev->addr])
+ if (phydev->mdio.bus->phy_map[phydev->mdio.addr])
return -EINVAL;
- phydev->bus->phy_map[phydev->addr] = phydev;
+ phydev->mdio.bus->phy_map[phydev->mdio.addr] = phydev;
/* Run all of the fixups for this PHY */
err = phy_scan_fixups(phydev);
if (err) {
- pr_err("PHY %d failed to initialize\n", phydev->addr);
+ pr_err("PHY %d failed to initialize\n", phydev->mdio.addr);
goto out;
}
- err = device_add(&phydev->dev);
+ err = device_add(&phydev->mdio.dev);
if (err) {
- pr_err("PHY %d failed to add\n", phydev->addr);
+ pr_err("PHY %d failed to add\n", phydev->mdio.addr);
goto out;
}
return 0;
out:
- phydev->bus->phy_map[phydev->addr] = NULL;
+ phydev->mdio.bus->phy_map[phydev->mdio.addr] = NULL;
return err;
}
EXPORT_SYMBOL(phy_device_register);
@@ -417,10 +419,10 @@
*/
void phy_device_remove(struct phy_device *phydev)
{
- struct mii_bus *bus = phydev->bus;
- int addr = phydev->addr;
+ struct mii_bus *bus = phydev->mdio.bus;
+ int addr = phydev->mdio.addr;
- device_del(&phydev->dev);
+ device_del(&phydev->mdio.dev);
bus->phy_map[addr] = NULL;
}
EXPORT_SYMBOL(phy_device_remove);
@@ -617,13 +619,13 @@
void phy_attached_print(struct phy_device *phydev, const char *fmt, ...)
{
if (!fmt) {
- dev_info(&phydev->dev, ATTACHED_FMT "\n",
+ dev_info(&phydev->mdio.dev, ATTACHED_FMT "\n",
phydev->drv->name, phydev_name(phydev),
phydev->irq);
} else {
va_list ap;
- dev_info(&phydev->dev, ATTACHED_FMT,
+ dev_info(&phydev->mdio.dev, ATTACHED_FMT,
phydev->drv->name, phydev_name(phydev),
phydev->irq);
@@ -652,8 +654,8 @@
int phy_attach_direct(struct net_device *dev, struct phy_device *phydev,
u32 flags, phy_interface_t interface)
{
- struct mii_bus *bus = phydev->bus;
- struct device *d = &phydev->dev;
+ struct mii_bus *bus = phydev->mdio.bus;
+ struct device *d = &phydev->mdio.dev;
int err;
if (!try_module_get(bus->owner)) {
@@ -771,8 +773,8 @@
* real driver could be loaded
*/
for (i = 0; i < ARRAY_SIZE(genphy_driver); i++) {
- if (phydev->dev.driver == &genphy_driver[i].driver) {
- device_release_driver(&phydev->dev);
+ if (phydev->mdio.dev.driver == &genphy_driver[i].driver) {
+ device_release_driver(&phydev->mdio.dev);
break;
}
}
@@ -781,16 +783,16 @@
* The phydev might go away on the put_device() below, so avoid
* a use-after-free bug by reading the underlying bus first.
*/
- bus = phydev->bus;
+ bus = phydev->mdio.bus;
- put_device(&phydev->dev);
+ put_device(&phydev->mdio.dev);
module_put(bus->owner);
}
EXPORT_SYMBOL(phy_detach);
int phy_suspend(struct phy_device *phydev)
{
- struct phy_driver *phydrv = to_phy_driver(phydev->dev.driver);
+ struct phy_driver *phydrv = to_phy_driver(phydev->mdio.dev.driver);
struct ethtool_wolinfo wol = { .cmd = ETHTOOL_GWOL };
int ret = 0;
@@ -813,7 +815,7 @@
int phy_resume(struct phy_device *phydev)
{
- struct phy_driver *phydrv = to_phy_driver(phydev->dev.driver);
+ struct phy_driver *phydrv = to_phy_driver(phydev->mdio.dev.driver);
int ret = 0;
if (phydrv->resume)
@@ -1330,7 +1332,7 @@
static void of_set_phy_supported(struct phy_device *phydev)
{
- struct device_node *node = phydev->dev.of_node;
+ struct device_node *node = phydev->mdio.dev.of_node;
u32 max_speed;
if (!IS_ENABLED(CONFIG_OF_MDIO))
@@ -1354,7 +1356,7 @@
static int phy_probe(struct device *dev)
{
struct phy_device *phydev = to_phy_device(dev);
- struct device_driver *drv = phydev->dev.driver;
+ struct device_driver *drv = phydev->mdio.dev.driver;
struct phy_driver *phydrv = to_phy_driver(drv);
int err = 0;
diff --git a/drivers/net/phy/smsc.c b/drivers/net/phy/smsc.c
index dc2da87..18c981b 100644
--- a/drivers/net/phy/smsc.c
+++ b/drivers/net/phy/smsc.c
@@ -44,7 +44,7 @@
static int smsc_phy_config_init(struct phy_device *phydev)
{
int __maybe_unused len;
- struct device *dev __maybe_unused = &phydev->dev;
+ struct device *dev __maybe_unused = &phydev->mdio.dev;
struct device_node *of_node __maybe_unused = dev->of_node;
int rc = phy_read(phydev, MII_LAN83C185_CTRL_STATUS);
int enable_energy = 1;