[SCSI] qla4xxx: Disable generating pause frames in case of FW hung
In case of FW hung ISP82xx generates continuous pause frames
which causes switch to disable port.
Added fix to disable generating pause frames in case of
FW hung
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
diff --git a/drivers/scsi/qla4xxx/ql4_mbx.c b/drivers/scsi/qla4xxx/ql4_mbx.c
index c259378..e1e66a4 100644
--- a/drivers/scsi/qla4xxx/ql4_mbx.c
+++ b/drivers/scsi/qla4xxx/ql4_mbx.c
@@ -219,6 +219,13 @@
ha->mailbox_timeout_count++;
mbx_sts[0] = (-1);
set_bit(DPC_RESET_HA, &ha->dpc_flags);
+ if (is_qla8022(ha)) {
+ ql4_printk(KERN_INFO, ha,
+ "disabling pause transmit on port 0 & 1.\n");
+ qla4_8xxx_wr_32(ha, QLA82XX_CRB_NIU + 0x98,
+ CRB_NIU_XG_PAUSE_CTL_P0 |
+ CRB_NIU_XG_PAUSE_CTL_P1);
+ }
goto mbox_exit;
}
diff --git a/drivers/scsi/qla4xxx/ql4_nx.h b/drivers/scsi/qla4xxx/ql4_nx.h
index cfb2f2e..dc45ac9 100644
--- a/drivers/scsi/qla4xxx/ql4_nx.h
+++ b/drivers/scsi/qla4xxx/ql4_nx.h
@@ -39,6 +39,9 @@
QLA82XX_TEMP_PANIC /* Fatal error, hardware has shut down. */
};
+#define CRB_NIU_XG_PAUSE_CTL_P0 0x1
+#define CRB_NIU_XG_PAUSE_CTL_P1 0x8
+
#define QLA82XX_HW_H0_CH_HUB_ADR 0x05
#define QLA82XX_HW_H1_CH_HUB_ADR 0x0E
#define QLA82XX_HW_H2_CH_HUB_ADR 0x03
diff --git a/drivers/scsi/qla4xxx/ql4_os.c b/drivers/scsi/qla4xxx/ql4_os.c
index 9d3eab5..e2ef776 100644
--- a/drivers/scsi/qla4xxx/ql4_os.c
+++ b/drivers/scsi/qla4xxx/ql4_os.c
@@ -2080,6 +2080,11 @@
dev_state = qla4_8xxx_rd_32(ha, QLA82XX_CRB_DEV_STATE);
if (qla4_8xxx_check_temp(ha)) {
+ ql4_printk(KERN_INFO, ha, "disabling pause"
+ " transmit on port 0 & 1.\n");
+ qla4_8xxx_wr_32(ha, QLA82XX_CRB_NIU + 0x98,
+ CRB_NIU_XG_PAUSE_CTL_P0 |
+ CRB_NIU_XG_PAUSE_CTL_P1);
set_bit(DPC_HA_UNRECOVERABLE, &ha->dpc_flags);
qla4xxx_wake_dpc(ha);
} else if (dev_state == QLA82XX_DEV_NEED_RESET &&
@@ -2099,6 +2104,11 @@
} else {
/* Check firmware health */
if (qla4_8xxx_check_fw_alive(ha)) {
+ ql4_printk(KERN_INFO, ha, "disabling pause"
+ " transmit on port 0 & 1.\n");
+ qla4_8xxx_wr_32(ha, QLA82XX_CRB_NIU + 0x98,
+ CRB_NIU_XG_PAUSE_CTL_P0 |
+ CRB_NIU_XG_PAUSE_CTL_P1);
halt_status = qla4_8xxx_rd_32(ha,
QLA82XX_PEG_HALT_STATUS1);