| /* |
| * Copyright 2012 ST-Ericsson AB |
| * |
| * The code contained herein is licensed under the GNU General Public |
| * License. You may obtain a copy of the GNU General Public License |
| * Version 2 or later at the following locations: |
| * |
| * http://www.opensource.org/licenses/gpl-license.html |
| * http://www.gnu.org/copyleft/gpl.html |
| * |
| * Device Tree for the TVK1281618 UIB |
| */ |
| |
| #include <dt-bindings/interrupt-controller/irq.h> |
| |
| / { |
| gpio_keys { |
| compatible = "gpio-keys"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| vdd-supply = <&ab8500_ldo_aux1_reg>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&prox_tvk_mode>, <&hall_tvk_mode>; |
| |
| button@139 { |
| /* Proximity sensor */ |
| gpios = <&gpio6 25 0x4>; |
| linux,code = <11>; /* SW_FRONT_PROXIMITY */ |
| label = "SFH7741 Proximity Sensor"; |
| }; |
| button@145 { |
| /* Hall sensor */ |
| gpios = <&gpio4 17 0x4>; |
| linux,code = <0>; /* SW_LID */ |
| label = "HED54XXU11 Hall Effect Sensor"; |
| }; |
| }; |
| |
| soc { |
| /* Add Synaptics touch screen, TC35893 keypad etc here */ |
| i2c@80004000 { |
| tc35893@44 { |
| compatible = "toshiba,tc35893"; |
| reg = <0x44>; |
| interrupt-parent = <&gpio6>; |
| interrupts = <26 IRQ_TYPE_EDGE_RISING>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&tc35893_tvk_mode>; |
| |
| interrupt-controller; |
| #interrupt-cells = <1>; |
| |
| tc3589x_gpio { |
| compatible = "toshiba,tc3589x-gpio"; |
| interrupts = <0>; |
| |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| }; |
| tc3589x_keypad { |
| compatible = "toshiba,tc3589x-keypad"; |
| interrupts = <6>; |
| debounce-delay-ms = <4>; |
| keypad,num-columns = <8>; |
| keypad,num-rows = <8>; |
| linux,no-autorepeat; |
| wakeup-source; |
| linux,keymap = <0x0301006b |
| 0x04010066 |
| 0x06040072 |
| 0x040200d7 |
| 0x0303006a |
| 0x0205000e |
| 0x0607008b |
| 0x0500001c |
| 0x0403000b |
| 0x03040034 |
| 0x05020067 |
| 0x0305006c |
| 0x040500e7 |
| 0x0005009e |
| 0x06020073 |
| 0x01030039 |
| 0x07060069 |
| 0x050500d9>; |
| }; |
| }; |
| }; |
| /* Sensors mounted on this board variant */ |
| i2c@80128000 { |
| lsm303dlh@18 { |
| /* Accelerometer */ |
| compatible = "st,lsm303dlh-accel"; |
| st,drdy-int-pin = <1>; |
| reg = <0x18>; |
| vdd-supply = <&ab8500_ldo_aux1_reg>; |
| vddio-supply = <&db8500_vsmps2_reg>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&accel_tvk_mode>; |
| interrupt-parent = <&gpio2>; |
| interrupts = <18 IRQ_TYPE_EDGE_RISING>, |
| <19 IRQ_TYPE_EDGE_RISING>; |
| }; |
| lsm303dlh@1e { |
| /* |
| * This magnetometer is packaged with |
| * the accelerometer, and has a DRDY line, |
| * however it is not connected on this |
| * board so it can not generate interrupts. |
| */ |
| compatible = "st,lsm303dlh-magn"; |
| reg = <0x1e>; |
| vdd-supply = <&ab8500_ldo_aux1_reg>; |
| vddio-supply = <&db8500_vsmps2_reg>; |
| }; |
| lis331dl@1c { |
| /* Accelerometer */ |
| compatible = "st,lis331dl-accel"; |
| st,drdy-int-pin = <1>; |
| reg = <0x1c>; |
| vdd-supply = <&ab8500_ldo_aux1_reg>; |
| vddio-supply = <&db8500_vsmps2_reg>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&accel_tvk_mode>; |
| interrupt-parent = <&gpio2>; |
| interrupts = <18 IRQ_TYPE_EDGE_RISING>, |
| <19 IRQ_TYPE_EDGE_RISING>; |
| }; |
| ak8974@0f { |
| /* Magnetometer */ |
| compatible = "asahi-kasei,ak8974"; |
| reg = <0x0f>; |
| vdd-supply = <&ab8500_ldo_aux1_reg>; |
| vddio-supply = <&db8500_vsmps2_reg>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&gyro_magn_tvk_mode>; |
| interrupt-parent = <&gpio1>; |
| interrupts = <0 IRQ_TYPE_EDGE_RISING>; |
| }; |
| l3g4200d@68 { |
| /* Gyroscope */ |
| compatible = "st,l3g4200d-gyro"; |
| st,drdy-int-pin = <2>; |
| reg = <0x68>; |
| vdd-supply = <&ab8500_ldo_aux1_reg>; |
| vddio-supply = <&db8500_vsmps2_reg>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&gyro_magn_tvk_mode>; |
| interrupt-parent = <&gpio1>; |
| interrupts = <0 IRQ_TYPE_EDGE_RISING>; |
| }; |
| lsp001wm@5c { |
| /* Barometer/pressure sensor */ |
| compatible = "st,lps001wp-press"; |
| reg = <0x5c>; |
| vdd-supply = <&ab8500_ldo_aux1_reg>; |
| vddio-supply = <&db8500_vsmps2_reg>; |
| }; |
| }; |
| pinctrl { |
| /* Pull up this GPIO pin */ |
| tc35893 { |
| tc35893_tvk_mode: tc35893_tvk { |
| tvk_cfg { |
| pins = "GPIO218_AH11"; |
| ste,config = <&gpio_in_pu>; |
| }; |
| }; |
| }; |
| prox { |
| prox_tvk_mode: prox_tvk { |
| tvk_cfg { |
| pins = "GPIO217_AH12"; |
| ste,config = <&gpio_in_pu>; |
| }; |
| }; |
| }; |
| hall { |
| hall_tvk_mode: hall_tvk { |
| tvk_cfg { |
| pins = "GPIO145_C13"; |
| ste,config = <&gpio_in_pu>; |
| }; |
| }; |
| }; |
| accelerometer { |
| accel_tvk_mode: accel_tvk { |
| /* Accelerometer interrupt lines 1 & 2 */ |
| tvk_cfg { |
| pins = "GPIO82_C1", "GPIO83_D3"; |
| ste,config = <&gpio_in_pd>; |
| }; |
| }; |
| }; |
| gyroscope { |
| /* |
| * These lines are shared between Gyroscope l3g400dh |
| * and AK8974 magnetometer. |
| */ |
| gyro_magn_tvk_mode: gyro_magn_tvk { |
| /* GPIO 31 used for INT pull down the line */ |
| tvk_cfg1 { |
| pins = "GPIO31_V3"; |
| ste,config = <&gpio_in_pd>; |
| }; |
| /* GPIO 32 used for DRDY, pull this down */ |
| tvk_cfg2 { |
| pins = "GPIO32_V2"; |
| ste,config = <&gpio_in_pd>; |
| }; |
| }; |
| }; |
| }; |
| }; |
| }; |