freescale: Move the Freescale drivers
Move the Freescale drivers into drivers/net/ethernet/freescale/ and
make the necessary Kconfig and Makefile changes.
CC: Sandeep Gopalpet <sandeep.kumar@freescale.com>
CC: Andy Fleming <afleming@freescale.com>
CC: Shlomi Gridish <gridish@freescale.com>
CC: Li Yang <leoli@freescale.com>
CC: Pantelis Antoniou <pantelis.antoniou@gmail.com>
CC: Vitaly Bordug <vbordug@ru.mvista.com>
CC: Dan Malek <dmalek@jlc.net>
CC: Sylvain Munaut <tnt@246tNt.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
diff --git a/drivers/net/ethernet/freescale/Kconfig b/drivers/net/ethernet/freescale/Kconfig
new file mode 100644
index 0000000..2fd2c61
--- /dev/null
+++ b/drivers/net/ethernet/freescale/Kconfig
@@ -0,0 +1,88 @@
+#
+# Freescale device configuration
+#
+
+config NET_VENDOR_FREESCALE
+ bool "Freescale devices"
+ depends on FSL_SOC || QUICC_ENGINE || CPM1 || CPM2 || PPC_MPC512x || \
+ M523x || M527x || M5272 || M528x || M520x || M532x || \
+ IMX_HAVE_PLATFORM_FEC || MXS_HAVE_PLATFORM_FEC || \
+ (PPC_MPC52xx && PPC_BESTCOMM)
+ ---help---
+ If you have a network (Ethernet) card belonging to this class, say Y
+ and read the Ethernet-HOWTO, available from
+ <http://www.tldp.org/docs.html#howto>.
+
+ Note that the answer to this question doesn't directly affect the
+ kernel: saying N will just cause the configurator to skip all
+ the questions about IBM devices. If you say Y, you will be asked for
+ your specific card in the following questions.
+
+if NET_VENDOR_FREESCALE
+
+config FEC
+ bool "FEC ethernet controller (of ColdFire and some i.MX CPUs)"
+ depends on (M523x || M527x || M5272 || M528x || M520x || M532x || \
+ IMX_HAVE_PLATFORM_FEC || MXS_HAVE_PLATFORM_FEC)
+ default IMX_HAVE_PLATFORM_FEC || MXS_HAVE_PLATFORM_FEC if ARM
+ select PHYLIB
+ ---help---
+ Say Y here if you want to use the built-in 10/100 Fast ethernet
+ controller on some Motorola ColdFire and Freescale i.MX processors.
+
+config FEC_MPC52xx
+ tristate "FEC MPC52xx driver"
+ depends on PPC_MPC52xx && PPC_BESTCOMM
+ select CRC32
+ select PHYLIB
+ select PPC_BESTCOMM_FEC
+ ---help---
+ This option enables support for the MPC5200's on-chip
+ Fast Ethernet Controller
+ If compiled as module, it will be called fec_mpc52xx.
+
+config FEC_MPC52xx_MDIO
+ bool "FEC MPC52xx MDIO bus driver"
+ depends on FEC_MPC52xx
+ default y
+ ---help---
+ The MPC5200's FEC can connect to the Ethernet either with
+ an external MII PHY chip or 10 Mbps 7-wire interface
+ (Motorola? industry standard).
+ If your board uses an external PHY connected to FEC, enable this.
+ If not sure, enable.
+ If compiled as module, it will be called fec_mpc52xx_phy.
+
+source "drivers/net/ethernet/freescale/fs_enet/Kconfig"
+
+config FSL_PQ_MDIO
+ tristate "Freescale PQ MDIO"
+ depends on FSL_SOC
+ select PHYLIB
+ ---help---
+ This driver supports the MDIO bus used by the gianfar and UCC drivers.
+
+config UCC_GETH
+ tristate "Freescale QE Gigabit Ethernet"
+ depends on QUICC_ENGINE
+ select FSL_PQ_MDIO
+ select PHYLIB
+ ---help---
+ This driver supports the Gigabit Ethernet mode of the QUICC Engine,
+ which is available on some Freescale SOCs.
+
+config UGETH_TX_ON_DEMAND
+ bool "Transmit on Demand support"
+ depends on UCC_GETH
+
+config GIANFAR
+ tristate "Gianfar Ethernet"
+ depends on FSL_SOC
+ select FSL_PQ_MDIO
+ select PHYLIB
+ select CRC32
+ ---help---
+ This driver supports the Gigabit TSEC on the MPC83xx, MPC85xx,
+ and MPC86xx family of chips, and the FEC on the 8540.
+
+endif # NET_VENDOR_FREESCALE