spi/spi-pl022: Resolve formatting issues
There were few formatting related issues in code. This patch fixes them.
Fixes include:
- Remove extra blank lines
- align code to 80 cols
- combine several lines to one line
- Replace multiple spaces with tabs
- Remove spaces before labels
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
diff --git a/drivers/spi/spi-pl022.c b/drivers/spi/spi-pl022.c
index 730b4a3..6209540 100644
--- a/drivers/spi/spi-pl022.c
+++ b/drivers/spi/spi-pl022.c
@@ -113,7 +113,6 @@
#define SSP_CR0_MASK_CSS_ST (0x1FUL << 16)
#define SSP_CR0_MASK_FRF_ST (0x3UL << 21)
-
/*
* SSP Control Register 0 - SSP_CR1
*/
@@ -283,7 +282,6 @@
#define SPI_POLLING_TIMEOUT 1000
-
/*
* The type of reading going on on this chip
*/
@@ -752,7 +750,6 @@
*/
}
-
/**
* next_transfer - Move to the Next transfer in the current spi message
* @pl022: SSP driver private data structure
@@ -1534,8 +1531,7 @@
/* Initial message state */
pl022->cur_msg->state = STATE_START;
pl022->cur_transfer = list_entry(pl022->cur_msg->transfers.next,
- struct spi_transfer,
- transfer_list);
+ struct spi_transfer, transfer_list);
/* Setup the SPI using the per chip configuration */
pl022->cur_chip = spi_get_ctldata(pl022->cur_msg->spi);
@@ -1557,7 +1553,6 @@
do_interrupt_dma_transfer(pl022);
}
-
static int __init init_queue(struct pl022 *pl022)
{
INIT_LIST_HEAD(&pl022->queue);
@@ -1566,8 +1561,8 @@
pl022->running = false;
pl022->busy = false;
- tasklet_init(&pl022->pump_transfers,
- pump_transfers, (unsigned long)pl022);
+ tasklet_init(&pl022->pump_transfers, pump_transfers,
+ (unsigned long)pl022);
INIT_WORK(&pl022->pump_messages, pump_messages);
pl022->workqueue = create_singlethread_workqueue(
@@ -1578,7 +1573,6 @@
return 0;
}
-
static int start_queue(struct pl022 *pl022)
{
unsigned long flags;
@@ -1601,7 +1595,6 @@
return 0;
}
-
static int stop_queue(struct pl022 *pl022)
{
unsigned long flags;
@@ -1861,7 +1854,6 @@
return 0;
}
-
/*
* A piece of default chip info unless the platform
* supplies it.
@@ -1879,7 +1871,6 @@
.cs_control = null_cs_control,
};
-
/**
* pl022_setup - setup function registered to SPI master framework
* @spi: spi device which is requesting setup
@@ -1956,7 +1947,6 @@
goto err_config_params;
}
-
status = verify_controller_parameters(pl022, chip_info);
if (status) {
dev_err(&spi->dev, "controller data is incorrect");
@@ -2096,7 +2086,8 @@
}
SSP_WRITE_BITS(chip->cr1, SSP_DISABLED, SSP_CR1_MASK_SSE, 1);
SSP_WRITE_BITS(chip->cr1, chip_info->hierarchy, SSP_CR1_MASK_MS, 2);
- SSP_WRITE_BITS(chip->cr1, chip_info->slave_tx_disable, SSP_CR1_MASK_SOD, 3);
+ SSP_WRITE_BITS(chip->cr1, chip_info->slave_tx_disable, SSP_CR1_MASK_SOD,
+ 3);
/* Save controller_state */
spi_set_ctldata(spi, chip);
@@ -2122,7 +2113,6 @@
kfree(chip);
}
-
static int __devinit
pl022_probe(struct amba_device *adev, const struct amba_id *id)
{
@@ -2337,7 +2327,6 @@
.loopback = true,
};
-
static struct vendor_data vendor_st = {
.fifodepth = 32,
.max_bpw = 32,
@@ -2392,9 +2381,9 @@
* and 32 locations deep TX/RX FIFO but no extended
* CR0/CR1 register
*/
- .id = 0x00080023,
- .mask = 0xffffffff,
- .data = &vendor_st_pl023,
+ .id = 0x00080023,
+ .mask = 0xffffffff,
+ .data = &vendor_st_pl023,
},
{
.id = 0x10080023,
@@ -2415,19 +2404,16 @@
.resume = pl022_resume,
};
-
static int __init pl022_init(void)
{
return amba_driver_register(&pl022_driver);
}
-
subsys_initcall(pl022_init);
static void __exit pl022_exit(void)
{
amba_driver_unregister(&pl022_driver);
}
-
module_exit(pl022_exit);
MODULE_AUTHOR("Linus Walleij <linus.walleij@stericsson.com>");