[AVR32] ATSTK1000: Move gpio-leds setup to setup.c
There may be other boards than STK1002 that want to use the leds on
STK1000. Move it to stk1000 common code to make it easier to reuse.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
diff --git a/arch/avr32/boards/atstk1000/Kconfig b/arch/avr32/boards/atstk1000/Kconfig
index 718578f..dcf9e9e 100644
--- a/arch/avr32/boards/atstk1000/Kconfig
+++ b/arch/avr32/boards/atstk1000/Kconfig
@@ -50,9 +50,9 @@
GPIO lines and accessed through the J1 jumper block. Say "y"
here to configure that SPI controller.
-config BOARD_ATSTK1002_J2_LED
+config BOARD_ATSTK1000_J2_LED
bool
- default BOARD_ATSTK1002_J2_LED8 || BOARD_ATSTK1002_J2_RGB
+ default BOARD_ATSTK1000_J2_LED8 || BOARD_ATSTK1000_J2_RGB
choice
prompt "LEDs connected to J2:"
@@ -64,12 +64,12 @@
IDC cable. A default "heartbeat" trigger is provided, but
you can of course override this.
-config BOARD_ATSTK1002_J2_LED8
+config BOARD_ATSTK1000_J2_LED8
bool "LED0..LED7"
help
Select this if J2 is jumpered to LED0..LED7 amber leds.
-config BOARD_ATSTK1002_J2_RGB
+config BOARD_ATSTK1000_J2_RGB
bool "RGB leds"
help
Select this if J2 is jumpered to the RGB leds.
diff --git a/arch/avr32/boards/atstk1000/atstk1000.h b/arch/avr32/boards/atstk1000/atstk1000.h
index 9a49ed0..9392d32 100644
--- a/arch/avr32/boards/atstk1000/atstk1000.h
+++ b/arch/avr32/boards/atstk1000/atstk1000.h
@@ -12,4 +12,6 @@
extern struct atmel_lcdfb_info atstk1000_lcdc_data;
+void atstk1000_setup_j2_leds(void);
+
#endif /* __ARCH_AVR32_BOARDS_ATSTK1000_ATSTK1000_H */
diff --git a/arch/avr32/boards/atstk1000/atstk1002.c b/arch/avr32/boards/atstk1000/atstk1002.c
index 5be0d13..2481d23 100644
--- a/arch/avr32/boards/atstk1000/atstk1002.c
+++ b/arch/avr32/boards/atstk1000/atstk1002.c
@@ -11,7 +11,6 @@
#include <linux/etherdevice.h>
#include <linux/init.h>
#include <linux/kernel.h>
-#include <linux/leds.h>
#include <linux/platform_device.h>
#include <linux/string.h>
#include <linux/types.h>
@@ -22,7 +21,7 @@
#include <asm/io.h>
#include <asm/setup.h>
-#include <asm/arch/at32ap7000.h>
+#include <asm/arch/at32ap700x.h>
#include <asm/arch/board.h>
#include <asm/arch/init.h>
#include <asm/arch/portmux.h>
@@ -141,65 +140,6 @@
clk_put(pclk);
}
-#ifdef CONFIG_BOARD_ATSTK1002_J2_LED
-
-static struct gpio_led stk_j2_led[] = {
-#ifdef CONFIG_BOARD_ATSTK1002_J2_LED8
-#define LEDSTRING "J2 jumpered to LED8"
- { .name = "led0:amber", .gpio = GPIO_PIN_PB( 8), },
- { .name = "led1:amber", .gpio = GPIO_PIN_PB( 9), },
- { .name = "led2:amber", .gpio = GPIO_PIN_PB(10), },
- { .name = "led3:amber", .gpio = GPIO_PIN_PB(13), },
- { .name = "led4:amber", .gpio = GPIO_PIN_PB(14), },
- { .name = "led5:amber", .gpio = GPIO_PIN_PB(15), },
- { .name = "led6:amber", .gpio = GPIO_PIN_PB(16), },
- { .name = "led7:amber", .gpio = GPIO_PIN_PB(30),
- .default_trigger = "heartbeat", },
-#else /* RGB */
-#define LEDSTRING "J2 jumpered to RGB LEDs"
- { .name = "r1:red", .gpio = GPIO_PIN_PB( 8), },
- { .name = "g1:green", .gpio = GPIO_PIN_PB(10), },
- { .name = "b1:blue", .gpio = GPIO_PIN_PB(14), },
-
- { .name = "r2:red", .gpio = GPIO_PIN_PB( 9),
- .default_trigger = "heartbeat", },
- { .name = "g2:green", .gpio = GPIO_PIN_PB(13), },
- { .name = "b2:blue", .gpio = GPIO_PIN_PB(15),
- .default_trigger = "heartbeat", },
- /* PB16, PB30 unused */
-#endif
-};
-
-static struct gpio_led_platform_data stk_j2_led_data = {
- .num_leds = ARRAY_SIZE(stk_j2_led),
- .leds = stk_j2_led,
-};
-
-static struct platform_device stk_j2_led_dev = {
- .name = "leds-gpio",
- .id = 2, /* gpio block J2 */
- .dev = {
- .platform_data = &stk_j2_led_data,
- },
-};
-
-static void setup_j2_leds(void)
-{
- unsigned i;
-
- for (i = 0; i < ARRAY_SIZE(stk_j2_led); i++)
- at32_select_gpio(stk_j2_led[i].gpio, AT32_GPIOF_OUTPUT);
-
- printk("STK1002: " LEDSTRING "\n");
- platform_device_register(&stk_j2_led_dev);
-}
-
-#else
-static void setup_j2_leds(void)
-{
-}
-#endif
-
#ifndef CONFIG_BOARD_ATSTK1002_SW1_CUSTOM
#ifndef CONFIG_BOARD_ATSTK1002_SW3_CUSTOM
static void __init at73c213_set_clk(struct at73c213_board_info *info)
@@ -298,7 +238,7 @@
at32_add_device_ssc(0, ATMEL_SSC_TX);
#endif
- setup_j2_leds();
+ atstk1000_setup_j2_leds();
#ifndef CONFIG_BOARD_ATSTK1002_SW3_CUSTOM
#ifndef CONFIG_BOARD_ATSTK1002_SW1_CUSTOM
diff --git a/arch/avr32/boards/atstk1000/setup.c b/arch/avr32/boards/atstk1000/setup.c
index c9af409..8bedf938 100644
--- a/arch/avr32/boards/atstk1000/setup.c
+++ b/arch/avr32/boards/atstk1000/setup.c
@@ -10,13 +10,17 @@
#include <linux/bootmem.h>
#include <linux/fb.h>
#include <linux/init.h>
+#include <linux/platform_device.h>
#include <linux/types.h>
#include <linux/linkage.h>
#include <video/atmel_lcdc.h>
#include <asm/setup.h>
+
+#include <asm/arch/at32ap700x.h>
#include <asm/arch/board.h>
+#include <asm/arch/portmux.h>
#include "atstk1000.h"
@@ -61,3 +65,63 @@
.default_monspecs = &atstk1000_default_monspecs,
.guard_time = 2,
};
+
+#ifdef CONFIG_BOARD_ATSTK1000_J2_LED
+#include <linux/leds.h>
+
+static struct gpio_led stk1000_j2_led[] = {
+#ifdef CONFIG_BOARD_ATSTK1000_J2_LED8
+#define LEDSTRING "J2 jumpered to LED8"
+ { .name = "led0:amber", .gpio = GPIO_PIN_PB( 8), },
+ { .name = "led1:amber", .gpio = GPIO_PIN_PB( 9), },
+ { .name = "led2:amber", .gpio = GPIO_PIN_PB(10), },
+ { .name = "led3:amber", .gpio = GPIO_PIN_PB(13), },
+ { .name = "led4:amber", .gpio = GPIO_PIN_PB(14), },
+ { .name = "led5:amber", .gpio = GPIO_PIN_PB(15), },
+ { .name = "led6:amber", .gpio = GPIO_PIN_PB(16), },
+ { .name = "led7:amber", .gpio = GPIO_PIN_PB(30),
+ .default_trigger = "heartbeat", },
+#else /* RGB */
+#define LEDSTRING "J2 jumpered to RGB LEDs"
+ { .name = "r1:red", .gpio = GPIO_PIN_PB( 8), },
+ { .name = "g1:green", .gpio = GPIO_PIN_PB(10), },
+ { .name = "b1:blue", .gpio = GPIO_PIN_PB(14), },
+
+ { .name = "r2:red", .gpio = GPIO_PIN_PB( 9),
+ .default_trigger = "heartbeat", },
+ { .name = "g2:green", .gpio = GPIO_PIN_PB(13), },
+ { .name = "b2:blue", .gpio = GPIO_PIN_PB(15),
+ .default_trigger = "heartbeat", },
+ /* PB16, PB30 unused */
+#endif
+};
+
+static struct gpio_led_platform_data stk1000_j2_led_data = {
+ .num_leds = ARRAY_SIZE(stk1000_j2_led),
+ .leds = stk1000_j2_led,
+};
+
+static struct platform_device stk1000_j2_led_dev = {
+ .name = "leds-gpio",
+ .id = 2, /* gpio block J2 */
+ .dev = {
+ .platform_data = &stk1000_j2_led_data,
+ },
+};
+
+void __init atstk1000_setup_j2_leds(void)
+{
+ unsigned i;
+
+ for (i = 0; i < ARRAY_SIZE(stk1000_j2_led); i++)
+ at32_select_gpio(stk1000_j2_led[i].gpio, AT32_GPIOF_OUTPUT);
+
+ printk("STK1000: " LEDSTRING "\n");
+ platform_device_register(&stk1000_j2_led_dev);
+}
+#else /* CONFIG_BOARD_ATSTK1000_J2_LED */
+void __init atstk1000_setup_j2_leds(void)
+{
+
+}
+#endif /* CONFIG_BOARD_ATSTK1000_J2_LED */