| # |
| # PINCTRL infrastructure and drivers |
| # |
| |
| config PINCTRL |
| bool |
| |
| if PINCTRL |
| |
| menu "Pin controllers" |
| depends on PINCTRL |
| |
| config PINMUX |
| bool "Support pin multiplexing controllers" if COMPILE_TEST |
| |
| config PINCONF |
| bool "Support pin configuration controllers" if COMPILE_TEST |
| |
| config GENERIC_PINCONF |
| bool |
| select PINCONF |
| |
| config DEBUG_PINCTRL |
| bool "Debug PINCTRL calls" |
| depends on DEBUG_KERNEL |
| help |
| Say Y here to add some extra checks and diagnostics to PINCTRL calls. |
| |
| config PINCTRL_ADI2 |
| bool "ADI pin controller driver" |
| depends on BLACKFIN |
| select PINMUX |
| select IRQ_DOMAIN |
| help |
| This is the pin controller and gpio driver for ADI BF54x, BF60x and |
| future processors. This option is selected automatically when specific |
| machine and arch are selected to build. |
| |
| config PINCTRL_AS3722 |
| bool "Pinctrl and GPIO driver for ams AS3722 PMIC" |
| depends on MFD_AS3722 && GPIOLIB |
| select PINMUX |
| select GENERIC_PINCONF |
| help |
| AS3722 device supports the configuration of GPIO pins for different |
| functionality. This driver supports the pinmux, push-pull and |
| open drain configuration for the GPIO pins of AS3722 devices. It also |
| supports the GPIO functionality through gpiolib. |
| |
| config PINCTRL_BF54x |
| def_bool y if BF54x |
| select PINCTRL_ADI2 |
| |
| config PINCTRL_BF60x |
| def_bool y if BF60x |
| select PINCTRL_ADI2 |
| |
| config PINCTRL_AT91 |
| bool "AT91 pinctrl driver" |
| depends on OF |
| depends on ARCH_AT91 |
| select PINMUX |
| select PINCONF |
| select GPIOLIB |
| select OF_GPIO |
| select GPIOLIB_IRQCHIP |
| help |
| Say Y here to enable the at91 pinctrl driver |
| |
| config PINCTRL_LANTIQ |
| bool |
| depends on LANTIQ |
| select PINMUX |
| select PINCONF |
| |
| config PINCTRL_FALCON |
| bool |
| depends on SOC_FALCON |
| depends on PINCTRL_LANTIQ |
| |
| config PINCTRL_MESON |
| bool |
| select PINMUX |
| select PINCONF |
| select GENERIC_PINCONF |
| select OF_GPIO |
| select REGMAP_MMIO |
| |
| config PINCTRL_ROCKCHIP |
| bool |
| select PINMUX |
| select GENERIC_PINCONF |
| select GENERIC_IRQ_CHIP |
| select MFD_SYSCON |
| |
| config PINCTRL_SINGLE |
| tristate "One-register-per-pin type device tree based pinctrl driver" |
| depends on OF |
| select PINMUX |
| select PINCONF |
| select GENERIC_PINCONF |
| help |
| This selects the device tree based generic pinctrl driver. |
| |
| config PINCTRL_SIRF |
| bool "CSR SiRFprimaII pin controller driver" |
| depends on ARCH_SIRF |
| select PINMUX |
| select GPIOLIB_IRQCHIP |
| |
| config PINCTRL_ST |
| bool |
| depends on OF |
| select PINMUX |
| select PINCONF |
| select GPIOLIB_IRQCHIP |
| |
| config PINCTRL_TEGRA |
| bool |
| select PINMUX |
| select PINCONF |
| |
| config PINCTRL_TEGRA20 |
| bool |
| select PINCTRL_TEGRA |
| |
| config PINCTRL_TEGRA30 |
| bool |
| select PINCTRL_TEGRA |
| |
| config PINCTRL_TEGRA114 |
| bool |
| select PINCTRL_TEGRA |
| |
| config PINCTRL_TEGRA124 |
| bool |
| select PINCTRL_TEGRA |
| |
| config PINCTRL_TEGRA210 |
| bool |
| select PINCTRL_TEGRA |
| |
| config PINCTRL_TEGRA_XUSB |
| def_bool y if ARCH_TEGRA |
| select GENERIC_PHY |
| select PINCONF |
| select PINMUX |
| |
| config PINCTRL_TZ1090 |
| bool "Toumaz Xenif TZ1090 pin control driver" |
| depends on SOC_TZ1090 |
| select PINMUX |
| select GENERIC_PINCONF |
| |
| config PINCTRL_TZ1090_PDC |
| bool "Toumaz Xenif TZ1090 PDC pin control driver" |
| depends on SOC_TZ1090 |
| select PINMUX |
| select PINCONF |
| |
| config PINCTRL_U300 |
| bool "U300 pin controller driver" |
| depends on ARCH_U300 |
| select PINMUX |
| select GENERIC_PINCONF |
| |
| config PINCTRL_COH901 |
| bool "ST-Ericsson U300 COH 901 335/571 GPIO" |
| depends on GPIOLIB && ARCH_U300 && PINCTRL_U300 |
| select GPIOLIB_IRQCHIP |
| help |
| Say yes here to support GPIO interface on ST-Ericsson U300. |
| The names of the two IP block variants supported are |
| COH 901 335 and COH 901 571/3. They contain 3, 5 or 7 |
| ports of 8 GPIO pins each. |
| |
| config PINCTRL_PALMAS |
| bool "Pinctrl driver for the PALMAS Series MFD devices" |
| depends on OF && MFD_PALMAS |
| select PINMUX |
| select GENERIC_PINCONF |
| help |
| Palmas device supports the configuration of pins for different |
| functionality. This driver supports the pinmux, push-pull and |
| open drain configuration for the Palmas series devices like |
| TPS65913, TPS80036 etc. |
| |
| config PINCTRL_ZYNQ |
| bool "Pinctrl driver for Xilinx Zynq" |
| depends on ARCH_ZYNQ |
| select PINMUX |
| select GENERIC_PINCONF |
| help |
| This selectes the pinctrl driver for Xilinx Zynq. |
| |
| source "drivers/pinctrl/bcm/Kconfig" |
| source "drivers/pinctrl/berlin/Kconfig" |
| source "drivers/pinctrl/freescale/Kconfig" |
| source "drivers/pinctrl/intel/Kconfig" |
| source "drivers/pinctrl/mvebu/Kconfig" |
| source "drivers/pinctrl/nomadik/Kconfig" |
| source "drivers/pinctrl/qcom/Kconfig" |
| source "drivers/pinctrl/samsung/Kconfig" |
| source "drivers/pinctrl/sh-pfc/Kconfig" |
| source "drivers/pinctrl/spear/Kconfig" |
| source "drivers/pinctrl/sunxi/Kconfig" |
| source "drivers/pinctrl/vt8500/Kconfig" |
| source "drivers/pinctrl/mediatek/Kconfig" |
| |
| config PINCTRL_XWAY |
| bool |
| depends on SOC_TYPE_XWAY |
| depends on PINCTRL_LANTIQ |
| |
| config PINCTRL_TB10X |
| bool |
| depends on ARC_PLAT_TB10X |
| |
| endmenu |
| |
| endif |