ARM: OMAP1: ams-delta: register latch dependent devices later
In preparation to converting Amstrad Delta on-board latches to
basic_mmio_gpio devices, registration of platform devices which depend
on latches and will require initialization of their GPIO pins first,
should be moved out of .machine_init down to late_initcall level, as the
gpio-generic driver is not available until device_initcall time. The
latch reset operation, which will be replaced with GPIO initialization,
must also be moved to late_initcall for the same reason.
Since there was already another, separate arch_initcall function for
setting up one of those latch dependent devices, the on-board modem
device, reuse that function, i.e., rename it to a name that matches the
new purpose, extend with other device setup relocated from
.machine_init, and move down to the late_initcall level.
While being at it, add missing gpio_free() in case the modem platform
device registration fails.
Thanks to Tony Lindgren <tony@atomide.com> who suggested this approach
instead of shifting up the gpio-generic driver initialization.
In addition, defer registration of the Amstrad Delta ASoC and serio
devices, done from their device driver files, until late_initcall time,
as those drivers will depend on their GPIO pins already requested from
the board late_init() function until updated to register their GPIO pins
themselves.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
diff --git a/arch/arm/mach-omap1/board-ams-delta.c b/arch/arm/mach-omap1/board-ams-delta.c
index b0f15d2..50987c9 100644
--- a/arch/arm/mach-omap1/board-ams-delta.c
+++ b/arch/arm/mach-omap1/board-ams-delta.c
@@ -275,11 +275,14 @@
};
static struct platform_device *ams_delta_devices[] __initdata = {
- &ams_delta_nand_device,
&ams_delta_kp_device,
+ &ams_delta_camera_device,
+};
+
+static struct platform_device *late_devices[] __initdata = {
+ &ams_delta_nand_device,
&ams_delta_lcd_device,
&ams_delta_led_device,
- &ams_delta_camera_device,
};
static void __init ams_delta_init(void)
@@ -307,9 +310,6 @@
omap_serial_init();
omap_register_i2c_bus(1, 100, NULL, 0);
- /* Clear latch2 (NAND, LCD, modem enable) */
- ams_delta_latch2_write(~0, 0);
-
omap1_usb_init(&ams_delta_usb_config);
omap1_set_camera_info(&ams_delta_camera_platform_data);
#ifdef CONFIG_LEDS_TRIGGERS
@@ -345,13 +345,18 @@
},
};
-static int __init ams_delta_modem_init(void)
+static int __init late_init(void)
{
int err;
if (!machine_is_ams_delta())
return -ENODEV;
+ /* Clear latch2 (NAND, LCD, modem enable) */
+ ams_delta_latch2_write(~0, 0);
+
+ platform_add_devices(late_devices, ARRAY_SIZE(late_devices));
+
omap_cfg_reg(M14_1510_GPIO2);
ams_delta_modem_ports[0].irq =
gpio_to_irq(AMS_DELTA_GPIO_PIN_MODEM_IRQ);
@@ -367,9 +372,16 @@
AMS_DELTA_LATCH2_MODEM_NRESET | AMS_DELTA_LATCH2_MODEM_CODEC,
AMS_DELTA_LATCH2_MODEM_NRESET | AMS_DELTA_LATCH2_MODEM_CODEC);
- return platform_device_register(&ams_delta_modem_device);
+ err = platform_device_register(&ams_delta_modem_device);
+ if (err)
+ goto gpio_free;
+ return 0;
+
+gpio_free:
+ gpio_free(AMS_DELTA_GPIO_PIN_MODEM_IRQ);
+ return err;
}
-arch_initcall(ams_delta_modem_init);
+late_initcall(late_init);
static void __init ams_delta_map_io(void)
{
diff --git a/drivers/input/serio/ams_delta_serio.c b/drivers/input/serio/ams_delta_serio.c
index d4d08bd..835d37a 100644
--- a/drivers/input/serio/ams_delta_serio.c
+++ b/drivers/input/serio/ams_delta_serio.c
@@ -165,7 +165,7 @@
kfree(ams_delta_serio);
return err;
}
-module_init(ams_delta_serio_init);
+late_initcall(ams_delta_serio_init);
static void __exit ams_delta_serio_exit(void)
{
diff --git a/sound/soc/omap/ams-delta.c b/sound/soc/omap/ams-delta.c
index ccb8a6a..be81bc7 100644
--- a/sound/soc/omap/ams-delta.c
+++ b/sound/soc/omap/ams-delta.c
@@ -636,7 +636,7 @@
platform_device_put(ams_delta_audio_platform_device);
return ret;
}
-module_init(ams_delta_module_init);
+late_initcall(ams_delta_module_init);
static void __exit ams_delta_module_exit(void)
{