| # drivers/mtd/maps/Kconfig |
| # $Id: Kconfig,v 1.61 2005/11/07 11:14:26 gleixner Exp $ |
| |
| menu "Mapping drivers for chip access" |
| depends on MTD!=n |
| |
| config MTD_COMPLEX_MAPPINGS |
| bool "Support non-linear mappings of flash chips" |
| depends on MTD |
| help |
| This causes the chip drivers to allow for complicated |
| paged mappings of flash chips. |
| |
| config MTD_PHYSMAP |
| tristate "CFI Flash device in physical memory map" |
| depends on MTD_CFI |
| help |
| This provides a 'mapping' driver which allows the CFI probe and |
| command set driver code to communicate with flash chips which |
| are mapped physically into the CPU's memory. You will need to |
| configure the physical address and size of the flash chips on |
| your particular board as well as the bus width, either statically |
| with config options or at run-time. |
| |
| config MTD_PHYSMAP_START |
| hex "Physical start address of flash mapping" |
| depends on MTD_PHYSMAP |
| default "0x8000000" |
| help |
| This is the physical memory location at which the flash chips |
| are mapped on your particular target board. Refer to the |
| memory map which should hopefully be in the documentation for |
| your board. |
| Ignore this option if you use run-time physmap configuration |
| (i.e., run-time calling physmap_configure()). |
| |
| config MTD_PHYSMAP_LEN |
| hex "Physical length of flash mapping" |
| depends on MTD_PHYSMAP |
| default "0" |
| help |
| This is the total length of the mapping of the flash chips on |
| your particular board. If there is space, or aliases, in the |
| physical memory map between the chips, this could be larger |
| than the total amount of flash present. Refer to the memory |
| map which should hopefully be in the documentation for your |
| board. |
| Ignore this option if you use run-time physmap configuration |
| (i.e., run-time calling physmap_configure()). |
| |
| config MTD_PHYSMAP_BANKWIDTH |
| int "Bank width in octets" |
| depends on MTD_PHYSMAP |
| default "2" |
| help |
| This is the total width of the data bus of the flash devices |
| in octets. For example, if you have a data bus width of 32 |
| bits, you would set the bus width octect value to 4. This is |
| used internally by the CFI drivers. |
| Ignore this option if you use run-time physmap configuration |
| (i.e., run-time calling physmap_configure()). |
| |
| config MTD_SUN_UFLASH |
| tristate "Sun Microsystems userflash support" |
| depends on SPARC && MTD_CFI |
| help |
| This provides a 'mapping' driver which supports the way in |
| which user-programmable flash chips are connected on various |
| Sun Microsystems boardsets. This driver will require CFI support |
| in the kernel, so if you did not enable CFI previously, do that now. |
| |
| config MTD_PNC2000 |
| tristate "CFI Flash device mapped on Photron PNC-2000" |
| depends on X86 && MTD_CFI && MTD_PARTITIONS |
| help |
| PNC-2000 is the name of Network Camera product from PHOTRON |
| Ltd. in Japan. It uses CFI-compliant flash. |
| |
| config MTD_SC520CDP |
| tristate "CFI Flash device mapped on AMD SC520 CDP" |
| depends on X86 && MTD_CFI && MTD_CONCAT |
| help |
| The SC520 CDP board has two banks of CFI-compliant chips and one |
| Dual-in-line JEDEC chip. This 'mapping' driver supports that |
| arrangement, implementing three MTD devices. |
| |
| config MTD_NETSC520 |
| tristate "CFI Flash device mapped on AMD NetSc520" |
| depends on X86 && MTD_CFI && MTD_PARTITIONS |
| help |
| This enables access routines for the flash chips on the AMD NetSc520 |
| demonstration board. If you have one of these boards and would like |
| to use the flash chips on it, say 'Y'. |
| |
| config MTD_TS5500 |
| tristate "JEDEC Flash device mapped on Technologic Systems TS-5500" |
| depends on X86 |
| select MTD_PARTITIONS |
| select MTD_JEDECPROBE |
| select MTD_CFI_AMDSTD |
| help |
| This provides a driver for the on-board flash of the Technologic |
| System's TS-5500 board. The 2MB flash is split into 3 partitions |
| which are accessed as separate MTD devices. |
| |
| mtd0 and mtd2 are the two BIOS drives, which use the resident |
| flash disk (RFD) flash translation layer. |
| |
| mtd1 allows you to reprogram your BIOS. BE VERY CAREFUL. |
| |
| Note that jumper 3 ("Write Enable Drive A") must be set |
| otherwise detection won't succeed. |
| |
| config MTD_SBC_GXX |
| tristate "CFI Flash device mapped on Arcom SBC-GXx boards" |
| depends on X86 && MTD_CFI_INTELEXT && MTD_PARTITIONS && MTD_COMPLEX_MAPPINGS |
| help |
| This provides a driver for the on-board flash of Arcom Control |
| Systems' SBC-GXn family of boards, formerly known as SBC-MediaGX. |
| By default the flash is split into 3 partitions which are accessed |
| as separate MTD devices. This board utilizes Intel StrataFlash. |
| More info at |
| <http://www.arcomcontrols.com/products/icp/pc104/processors/SBC_GX1.htm>. |
| |
| config MTD_LUBBOCK |
| tristate "CFI Flash device mapped on Intel Lubbock XScale eval board" |
| depends on ARCH_LUBBOCK && MTD_CFI_INTELEXT && MTD_PARTITIONS |
| help |
| This provides a driver for the on-board flash of the Intel |
| 'Lubbock' XScale evaluation board. |
| |
| config MTD_MAINSTONE |
| tristate "CFI Flash device mapped on Intel Mainstone XScale eval board" |
| depends on MACH_MAINSTONE && MTD_CFI_INTELEXT |
| select MTD_PARTITIONS |
| help |
| This provides a driver for the on-board flash of the Intel |
| 'Mainstone PXA27x evaluation board. |
| |
| config MTD_OCTAGON |
| tristate "JEDEC Flash device mapped on Octagon 5066 SBC" |
| depends on X86 && MTD_JEDEC && MTD_COMPLEX_MAPPINGS |
| help |
| This provides a 'mapping' driver which supports the way in which |
| the flash chips are connected in the Octagon-5066 Single Board |
| Computer. More information on the board is available at |
| <http://www.octagonsystems.com/CPUpages/5066.html>. |
| |
| config MTD_VMAX |
| tristate "JEDEC Flash device mapped on Tempustech VMAX SBC301" |
| depends on X86 && MTD_JEDEC && MTD_COMPLEX_MAPPINGS |
| help |
| This provides a 'mapping' driver which supports the way in which |
| the flash chips are connected in the Tempustech VMAX SBC301 Single |
| Board Computer. More information on the board is available at |
| <http://www.tempustech.com/>. |
| |
| config MTD_SCx200_DOCFLASH |
| tristate "Flash device mapped with DOCCS on NatSemi SCx200" |
| depends on SCx200 && MTD_CFI && MTD_PARTITIONS |
| help |
| Enable support for a flash chip mapped using the DOCCS signal on a |
| National Semiconductor SCx200 processor. |
| |
| If you don't know what to do here, say N. |
| |
| If compiled as a module, it will be called scx200_docflash. |
| |
| config MTD_AMD76XROM |
| tristate "BIOS flash chip on AMD76x southbridge" |
| depends on X86 && MTD_JEDECPROBE |
| help |
| Support for treating the BIOS flash chip on AMD76x motherboards |
| as an MTD device - with this you can reprogram your BIOS. |
| |
| BE VERY CAREFUL. |
| |
| config MTD_ICHXROM |
| tristate "BIOS flash chip on Intel Controller Hub 2/3/4/5" |
| depends on X86 && MTD_JEDECPROBE |
| help |
| Support for treating the BIOS flash chip on ICHX motherboards |
| as an MTD device - with this you can reprogram your BIOS. |
| |
| BE VERY CAREFUL. |
| |
| config MTD_SCB2_FLASH |
| tristate "BIOS flash chip on Intel SCB2 boards" |
| depends on X86 && MTD_JEDECPROBE |
| help |
| Support for treating the BIOS flash chip on Intel SCB2 boards |
| as an MTD device - with this you can reprogram your BIOS. |
| |
| BE VERY CAREFUL. |
| |
| config MTD_TSUNAMI |
| tristate "Flash chips on Tsunami TIG bus" |
| depends on ALPHA_TSUNAMI && MTD_COMPLEX_MAPPINGS |
| help |
| Support for the flash chip on Tsunami TIG bus. |
| |
| config MTD_LASAT |
| tristate "LASAT flash device" |
| depends on LASAT && MTD_CFI |
| help |
| Support for the flash chips on the Lasat 100 and 200 boards. |
| |
| config MTD_NETtel |
| tristate "CFI flash device on SnapGear/SecureEdge" |
| depends on X86 && MTD_PARTITIONS && MTD_JEDECPROBE |
| help |
| Support for flash chips on NETtel/SecureEdge/SnapGear boards. |
| |
| config MTD_ALCHEMY |
| tristate "AMD Alchemy Pb1xxx/Db1xxx/RDK MTD support" |
| depends on SOC_AU1X00 |
| help |
| Flash memory access on AMD Alchemy Pb/Db/RDK Reference Boards |
| |
| config MTD_MTX1 |
| tristate "4G Systems MTX-1 Flash device" |
| depends on MIPS && MIPS_MTX1 |
| help |
| Flash memory access on 4G Systems MTX-1 Board. If you have one of |
| these boards and would like to use the flash chips on it, say 'Y'. |
| |
| config MTD_DILNETPC |
| tristate "CFI Flash device mapped on DIL/Net PC" |
| depends on X86 && MTD_CONCAT && MTD_PARTITIONS && MTD_CFI_INTELEXT |
| help |
| MTD map driver for SSV DIL/Net PC Boards "DNP" and "ADNP". |
| For details, see <http://www.ssv-embedded.de/ssv/pc104/p169.htm> |
| and <http://www.ssv-embedded.de/ssv/pc104/p170.htm> |
| |
| config MTD_DILNETPC_BOOTSIZE |
| hex "Size of DIL/Net PC flash boot partition" |
| depends on MTD_DILNETPC |
| default "0x80000" |
| help |
| The amount of space taken up by the kernel or Etherboot |
| on the DIL/Net PC flash chips. |
| |
| config MTD_L440GX |
| tristate "BIOS flash chip on Intel L440GX boards" |
| depends on X86 && MTD_JEDECPROBE |
| help |
| Support for treating the BIOS flash chip on Intel L440GX motherboards |
| as an MTD device - with this you can reprogram your BIOS. |
| |
| BE VERY CAREFUL. |
| |
| config MTD_SBC8240 |
| tristate "Flash device on SBC8240" |
| depends on MTD_JEDECPROBE && 8260 |
| help |
| Flash access on the SBC8240 board from Wind River. See |
| <http://www.windriver.com/products/sbc8240/> |
| |
| config MTD_TQM8XXL |
| tristate "CFI Flash device mapped on TQM8XXL" |
| depends on MTD_CFI && TQM8xxL |
| help |
| The TQM8xxL PowerPC board has up to two banks of CFI-compliant |
| chips, currently uses AMD one. This 'mapping' driver supports |
| that arrangement, allowing the CFI probe and command set driver |
| code to communicate with the chips on the TQM8xxL board. More at |
| <http://www.denx.de/embedded-ppc-en.html>. |
| |
| config MTD_RPXLITE |
| tristate "CFI Flash device mapped on RPX Lite or CLLF" |
| depends on MTD_CFI && (RPXCLASSIC || RPXLITE) |
| help |
| The RPXLite PowerPC board has CFI-compliant chips mapped in |
| a strange sparse mapping. This 'mapping' driver supports that |
| arrangement, allowing the CFI probe and command set driver code |
| to communicate with the chips on the RPXLite board. More at |
| <http://www.embeddedplanet.com/>. |
| |
| config MTD_MBX860 |
| tristate "System flash on MBX860 board" |
| depends on MTD_CFI && MBX |
| help |
| This enables access routines for the flash chips on the Motorola |
| MBX860 board. If you have one of these boards and would like |
| to use the flash chips on it, say 'Y'. |
| |
| config MTD_DBOX2 |
| tristate "CFI Flash device mapped on D-Box2" |
| depends on DBOX2 && MTD_CFI_INTELSTD && MTD_CFI_INTELEXT && MTD_CFI_AMDSTD |
| help |
| This enables access routines for the flash chips on the Nokia/Sagem |
| D-Box 2 board. If you have one of these boards and would like to use |
| the flash chips on it, say 'Y'. |
| |
| config MTD_CFI_FLAGADM |
| tristate "CFI Flash device mapping on FlagaDM" |
| depends on 8xx && MTD_CFI |
| help |
| Mapping for the Flaga digital module. If you don't have one, ignore |
| this setting. |
| |
| config MTD_BEECH |
| tristate "CFI Flash device mapped on IBM 405LP Beech" |
| depends on MTD_CFI && BEECH |
| help |
| This enables access routines for the flash chips on the IBM |
| 405LP Beech board. If you have one of these boards and would like |
| to use the flash chips on it, say 'Y'. |
| |
| config MTD_ARCTIC |
| tristate "CFI Flash device mapped on IBM 405LP Arctic" |
| depends on MTD_CFI && ARCTIC2 |
| help |
| This enables access routines for the flash chips on the IBM 405LP |
| Arctic board. If you have one of these boards and would like to |
| use the flash chips on it, say 'Y'. |
| |
| config MTD_WALNUT |
| tristate "Flash device mapped on IBM 405GP Walnut" |
| depends on MTD_JEDECPROBE && WALNUT |
| help |
| This enables access routines for the flash chips on the IBM 405GP |
| Walnut board. If you have one of these boards and would like to |
| use the flash chips on it, say 'Y'. |
| |
| config MTD_EBONY |
| tristate "Flash devices mapped on IBM 440GP Ebony" |
| depends on MTD_JEDECPROBE && EBONY |
| help |
| This enables access routines for the flash chips on the IBM 440GP |
| Ebony board. If you have one of these boards and would like to |
| use the flash chips on it, say 'Y'. |
| |
| config MTD_OCOTEA |
| tristate "Flash devices mapped on IBM 440GX Ocotea" |
| depends on MTD_CFI && OCOTEA |
| help |
| This enables access routines for the flash chips on the IBM 440GX |
| Ocotea board. If you have one of these boards and would like to |
| use the flash chips on it, say 'Y'. |
| |
| config MTD_REDWOOD |
| tristate "CFI Flash devices mapped on IBM Redwood" |
| depends on MTD_CFI && ( REDWOOD_4 || REDWOOD_5 || REDWOOD_6 ) |
| help |
| This enables access routines for the flash chips on the IBM |
| Redwood board. If you have one of these boards and would like to |
| use the flash chips on it, say 'Y'. |
| |
| config MTD_TQM834x |
| tristate "Flash device mapped on TQ Components TQM834x Boards" |
| depends on MTD_CFI && TQM834x |
| help |
| This enables access routines for the flash chips on the |
| TQ Components TQM834x boards. If you have one of these boards |
| and would like to use the flash chips on it, say 'Y'. |
| |
| config MTD_CSTM_MIPS_IXX |
| tristate "Flash chip mapping on ITE QED-4N-S01B, Globespan IVR or custom board" |
| depends on MIPS && MTD_CFI && MTD_JEDECPROBE && MTD_PARTITIONS |
| help |
| This provides a mapping driver for the Integrated Technology |
| Express, Inc (ITE) QED-4N-S01B eval board and the Globespan IVR |
| Reference Board. It provides the necessary addressing, length, |
| buswidth, vpp code and addition setup of the flash device for |
| these boards. In addition, this mapping driver can be used for |
| other boards via setting of the CONFIG_MTD_CSTM_MIPS_IXX_START/ |
| LEN/BUSWIDTH parameters. This mapping will provide one mtd device |
| using one partition. The start address can be offset from the |
| beginning of flash and the len can be less than the total flash |
| device size to allow a window into the flash. Both CFI and JEDEC |
| probes are called. |
| |
| config MTD_CSTM_MIPS_IXX_START |
| hex "Physical start address of flash mapping" |
| depends on MTD_CSTM_MIPS_IXX |
| default "0x8000000" |
| help |
| This is the physical memory location that the MTD driver will |
| use for the flash chips on your particular target board. |
| Refer to the memory map which should hopefully be in the |
| documentation for your board. |
| |
| config MTD_CSTM_MIPS_IXX_LEN |
| hex "Physical length of flash mapping" |
| depends on MTD_CSTM_MIPS_IXX |
| default "0x4000000" |
| help |
| This is the total length that the MTD driver will use for the |
| flash chips on your particular board. Refer to the memory |
| map which should hopefully be in the documentation for your |
| board. |
| |
| config MTD_CSTM_MIPS_IXX_BUSWIDTH |
| int "Bus width in octets" |
| depends on MTD_CSTM_MIPS_IXX |
| default "2" |
| help |
| This is the total bus width of the mapping of the flash chips |
| on your particular board. |
| |
| config MTD_OCELOT |
| tristate "Momenco Ocelot boot flash device" |
| depends on MIPS && MOMENCO_OCELOT |
| help |
| This enables access routines for the boot flash device and for the |
| NVRAM on the Momenco Ocelot board. If you have one of these boards |
| and would like access to either of these, say 'Y'. |
| |
| config MTD_SOLUTIONENGINE |
| tristate "CFI Flash device mapped on Hitachi SolutionEngine" |
| depends on SUPERH && MTD_CFI && MTD_REDBOOT_PARTS |
| help |
| This enables access to the flash chips on the Hitachi SolutionEngine and |
| similar boards. Say 'Y' if you are building a kernel for such a board. |
| |
| config MTD_ARM_INTEGRATOR |
| tristate "CFI Flash device mapped on ARM Integrator/P720T" |
| depends on ARM && MTD_CFI |
| |
| config MTD_CDB89712 |
| tristate "Cirrus CDB89712 evaluation board mappings" |
| depends on MTD_CFI && ARCH_CDB89712 |
| help |
| This enables access to the flash or ROM chips on the CDB89712 board. |
| If you have such a board, say 'Y'. |
| |
| config MTD_SA1100 |
| tristate "CFI Flash device mapped on StrongARM SA11x0" |
| depends on MTD_CFI && ARCH_SA1100 && MTD_PARTITIONS |
| help |
| This enables access to the flash chips on most platforms based on |
| the SA1100 and SA1110, including the Assabet and the Compaq iPAQ. |
| If you have such a board, say 'Y'. |
| |
| config MTD_IPAQ |
| tristate "CFI Flash device mapped on Compaq/HP iPAQ" |
| depends on IPAQ_HANDHELD && MTD_CFI |
| help |
| This provides a driver for the on-board flash of the iPAQ. |
| |
| config MTD_DC21285 |
| tristate "CFI Flash device mapped on DC21285 Footbridge" |
| depends on MTD_CFI && ARCH_FOOTBRIDGE && MTD_COMPLEX_MAPPINGS |
| help |
| This provides a driver for the flash accessed using Intel's |
| 21285 bridge used with Intel's StrongARM processors. More info at |
| <http://www.intel.com/design/bridge/docs/21285_documentation.htm>. |
| |
| config MTD_IQ80310 |
| tristate "CFI Flash device mapped on the XScale IQ80310 board" |
| depends on MTD_CFI && ARCH_IQ80310 |
| help |
| This enables access routines for the flash chips on the Intel XScale |
| IQ80310 evaluation board. If you have one of these boards and would |
| like to use the flash chips on it, say 'Y'. |
| |
| config MTD_IXP4XX |
| tristate "CFI Flash device mapped on Intel IXP4xx based systems" |
| depends on MTD_CFI && MTD_COMPLEX_MAPPINGS && ARCH_IXP4XX |
| help |
| This enables MTD access to flash devices on platforms based |
| on Intel's IXP4xx family of network processors such as the |
| IXDP425 and Coyote. If you have an IXP4xx based board and |
| would like to use the flash chips on it, say 'Y'. |
| |
| config MTD_IXP2000 |
| tristate "CFI Flash device mapped on Intel IXP2000 based systems" |
| depends on MTD_CFI && MTD_COMPLEX_MAPPINGS && ARCH_IXP2000 |
| help |
| This enables MTD access to flash devices on platforms based |
| on Intel's IXP2000 family of network processors such as the |
| IXDP425 and Coyote. If you have an IXP2000 based board and |
| would like to use the flash chips on it, say 'Y'. |
| |
| config MTD_FORTUNET |
| tristate "CFI Flash device mapped on the FortuNet board" |
| depends on MTD_CFI && MTD_PARTITIONS && SA1100_FORTUNET |
| help |
| This enables access to the Flash on the FortuNet board. If you |
| have such a board, say 'Y'. |
| |
| config MTD_AUTCPU12 |
| tristate "NV-RAM mapping AUTCPU12 board" |
| depends on ARCH_AUTCPU12 |
| help |
| This enables access to the NV-RAM on autronix autcpu12 board. |
| If you have such a board, say 'Y'. |
| |
| config MTD_EDB7312 |
| tristate "CFI Flash device mapped on EDB7312" |
| depends on ARCH_EDB7312 && MTD_CFI |
| help |
| This enables access to the CFI Flash on the Cogent EDB7312 board. |
| If you have such a board, say 'Y' here. |
| |
| config MTD_IMPA7 |
| tristate "JEDEC Flash device mapped on impA7" |
| depends on ARM && MTD_JEDECPROBE |
| help |
| This enables access to the NOR Flash on the impA7 board of |
| implementa GmbH. If you have such a board, say 'Y' here. |
| |
| config MTD_CEIVA |
| tristate "JEDEC Flash device mapped on Ceiva/Polaroid PhotoMax Digital Picture Frame" |
| depends on MTD_JEDECPROBE && ARCH_CEIVA |
| help |
| This enables access to the flash chips on the Ceiva/Polaroid |
| PhotoMax Digital Picture Frame. |
| If you have such a device, say 'Y'. |
| |
| config MTD_NOR_TOTO |
| tristate "NOR Flash device on TOTO board" |
| depends on ARCH_OMAP && OMAP_TOTO |
| help |
| This enables access to the NOR flash on the Texas Instruments |
| TOTO board. |
| |
| config MTD_H720X |
| tristate "Hynix evaluation board mappings" |
| depends on MTD_CFI && ( ARCH_H7201 || ARCH_H7202 ) |
| help |
| This enables access to the flash chips on the Hynix evaluation boards. |
| If you have such a board, say 'Y'. |
| |
| config MTD_MPC1211 |
| tristate "CFI Flash device mapped on Interface MPC-1211" |
| depends on SH_MPC1211 && MTD_CFI |
| help |
| This enables access to the flash chips on the Interface MPC-1211(CTP/PCI/MPC-SH02). |
| If you have such a board, say 'Y'. |
| |
| config MTD_OMAP_NOR |
| tristate "TI OMAP board mappings" |
| depends on MTD_CFI && ARCH_OMAP |
| help |
| This enables access to the NOR flash chips on TI OMAP-based |
| boards defining flash platform devices and flash platform data. |
| These boards include the Innovator, H2, H3, OSK, Perseus2, and |
| more. If you have such a board, say 'Y'. |
| |
| # This needs CFI or JEDEC, depending on the cards found. |
| config MTD_PCI |
| tristate "PCI MTD driver" |
| depends on MTD && PCI && MTD_COMPLEX_MAPPINGS |
| help |
| Mapping for accessing flash devices on add-in cards like the Intel XScale |
| IQ80310 card, and the Intel EBSA285 card in blank ROM programming mode |
| (please see the manual for the link settings). |
| |
| If you are not sure, say N. |
| |
| config MTD_PCMCIA |
| tristate "PCMCIA MTD driver" |
| depends on MTD && PCMCIA && MTD_COMPLEX_MAPPINGS && BROKEN |
| help |
| Map driver for accessing PCMCIA linear flash memory cards. These |
| cards are usually around 4-16MiB in size. This does not include |
| Compact Flash cards which are treated as IDE devices. |
| |
| config MTD_PCMCIA_ANONYMOUS |
| bool "Use PCMCIA MTD drivers for anonymous PCMCIA cards" |
| depends on MTD_PCMCIA |
| help |
| If this option is enabled, PCMCIA cards which do not report |
| anything about themselves are assumed to be MTD cards. |
| |
| If unsure, say N. |
| |
| config MTD_UCLINUX |
| tristate "Generic uClinux RAM/ROM filesystem support" |
| depends on MTD_PARTITIONS && !MMU |
| help |
| Map driver to support image based filesystems for uClinux. |
| |
| config MTD_WRSBC8260 |
| tristate "Map driver for WindRiver PowerQUICC II MPC82xx board" |
| depends on (SBC82xx || SBC8560) |
| select MTD_PARTITIONS |
| select MTD_MAP_BANK_WIDTH_4 |
| select MTD_MAP_BANK_WIDTH_1 |
| select MTD_CFI_I1 |
| select MTD_CFI_I4 |
| help |
| Map driver for WindRiver PowerQUICC II MPC82xx board. Drives |
| all three flash regions on CS0, CS1 and CS6 if they are configured |
| correctly by the boot loader. |
| |
| config MTD_DMV182 |
| tristate "Map driver for Dy-4 SVME/DMV-182 board." |
| depends on DMV182 |
| select MTD_PARTITIONS |
| select MTD_MAP_BANK_WIDTH_32 |
| select MTD_CFI_I8 |
| select MTD_CFI_AMDSTD |
| help |
| Map driver for Dy-4 SVME/DMV-182 board. |
| |
| config MTD_BAST |
| tristate "Map driver for Simtec BAST (EB2410ITX) or Thorcom VR1000" |
| depends on ARCH_BAST || MACH_VR1000 |
| select MTD_PARTITIONS |
| select MTD_MAP_BANK_WIDTH_16 |
| select MTD_JEDECPROBE |
| help |
| Map driver for NOR flash on the Simtec BAST (EB2410ITX), or the |
| Thorcom VR1000 |
| |
| Note, this driver *cannot* over-ride the WP link on the |
| board, or currently detect the state of the link. |
| |
| config MTD_BAST_MAXSIZE |
| int "Maximum size for BAST flash area (MiB)" |
| depends on MTD_BAST |
| default "4" |
| |
| config MTD_SHARP_SL |
| bool "ROM maped on Sharp SL Series" |
| depends on MTD && ARCH_PXA |
| help |
| This enables access to the flash chip on the Sharp SL Series of PDAs. |
| |
| config MTD_PLATRAM |
| tristate "Map driver for platform device RAM (mtd-ram)" |
| depends on MTD |
| select MTD_RAM |
| help |
| Map driver for RAM areas described via the platform device |
| system. |
| |
| This selection automatically selects the map_ram driver. |
| |
| endmenu |
| |