e1000e: Expand workaround for 10Mb HD throughput bug
In commit 772d05c51c4f4896c120ad418b1e91144a2ac813 "e1000e: slow performance
between two 82579 connected via 10Mbit hub", a workaround was put into place
to address the overaggressive transmit behavior of 82579 parts when connecting
at 10Mbs half-duplex.
This same behavior is seen on i217 and i218 parts as well. This patch expands
the original workaround to encompass these parts.
Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
diff --git a/drivers/net/ethernet/intel/e1000e/ich8lan.c b/drivers/net/ethernet/intel/e1000e/ich8lan.c
index 9b736b8..059f1b0 100644
--- a/drivers/net/ethernet/intel/e1000e/ich8lan.c
+++ b/drivers/net/ethernet/intel/e1000e/ich8lan.c
@@ -1314,14 +1314,17 @@
return ret_val;
}
- /* When connected at 10Mbps half-duplex, 82579 parts are excessively
+ /* When connected at 10Mbps half-duplex, some parts are excessively
* aggressive resulting in many collisions. To avoid this, increase
* the IPG and reduce Rx latency in the PHY.
*/
- if ((hw->mac.type == e1000_pch2lan) && link) {
+ if (((hw->mac.type == e1000_pch2lan) ||
+ (hw->mac.type == e1000_pch_lpt)) && link) {
u32 reg;
reg = er32(STATUS);
if (!(reg & (E1000_STATUS_FD | E1000_STATUS_SPEED_MASK))) {
+ u16 emi_addr;
+
reg = er32(TIPG);
reg &= ~E1000_TIPG_IPGT_MASK;
reg |= 0xFF;
@@ -1332,8 +1335,12 @@
if (ret_val)
return ret_val;
- ret_val =
- e1000_write_emi_reg_locked(hw, I82579_RX_CONFIG, 0);
+ if (hw->mac.type == e1000_pch2lan)
+ emi_addr = I82579_RX_CONFIG;
+ else
+ emi_addr = I217_RX_CONFIG;
+
+ ret_val = e1000_write_emi_reg_locked(hw, emi_addr, 0);
hw->phy.ops.release(hw);
diff --git a/drivers/net/ethernet/intel/e1000e/ich8lan.h b/drivers/net/ethernet/intel/e1000e/ich8lan.h
index bead50f..8fc6c15 100644
--- a/drivers/net/ethernet/intel/e1000e/ich8lan.h
+++ b/drivers/net/ethernet/intel/e1000e/ich8lan.h
@@ -242,6 +242,7 @@
#define I217_EEE_CAPABILITY 0x8000 /* IEEE MMD Register 3.20 */
#define I217_EEE_ADVERTISEMENT 0x8001 /* IEEE MMD Register 7.60 */
#define I217_EEE_LP_ABILITY 0x8002 /* IEEE MMD Register 7.61 */
+#define I217_RX_CONFIG 0xB20C /* Receive configuration */
#define E1000_EEE_RX_LPI_RCVD 0x0400 /* Tx LP idle received */
#define E1000_EEE_TX_LPI_RCVD 0x0800 /* Rx LP idle received */