| # arch/arm/plat-s3c/Kconfig |
| # |
| # Copyright 2007 Simtec Electronics |
| # |
| # Licensed under GPLv2 |
| |
| config PLAT_S3C |
| bool |
| depends on ARCH_S3C2410 || ARCH_S3C24A0 || ARCH_S3C64XX |
| default y |
| select NO_IOPORT |
| help |
| Base platform code for any Samsung S3C device |
| |
| # low-level serial option nodes |
| |
| config CPU_LLSERIAL_S3C2410_ONLY |
| bool |
| depends on PLAT_S3C |
| default y if CPU_LLSERIAL_S3C2410 && !CPU_LLSERIAL_S3C2440 |
| |
| config CPU_LLSERIAL_S3C2440_ONLY |
| bool |
| depends on PLAT_S3C |
| default y if CPU_LLSERIAL_S3C2440 && !CPU_LLSERIAL_S3C2410 |
| |
| config CPU_LLSERIAL_S3C2410 |
| bool |
| depends on PLAT_S3C |
| help |
| Selected if there is an S3C2410 (or register compatible) serial |
| low-level implementation needed |
| |
| config CPU_LLSERIAL_S3C2440 |
| bool |
| depends on PLAT_S3C |
| help |
| Selected if there is an S3C2440 (or register compatible) serial |
| low-level implementation needed |
| |
| # boot configurations |
| |
| comment "Boot options" |
| |
| config S3C_BOOT_WATCHDOG |
| bool "S3C Initialisation watchdog" |
| depends on PLAT_S3C && S3C2410_WATCHDOG |
| help |
| Say y to enable the watchdog during the kernel decompression |
| stage. If the kernel fails to uncompress, then the watchdog |
| will trigger a reset and the system should restart. |
| |
| config S3C_BOOT_ERROR_RESET |
| bool "S3C Reboot on decompression error" |
| depends on PLAT_S3C |
| help |
| Say y here to use the watchdog to reset the system if the |
| kernel decompressor detects an error during decompression. |
| |
| config S3C_BOOT_UART_FORCE_FIFO |
| bool "Force UART FIFO on during boot process" |
| depends on PLAT_S3C |
| default y |
| help |
| Say Y here to force the UART FIFOs on during the kernel |
| uncompressor |
| |
| comment "Power management" |
| |
| config S3C2410_PM_DEBUG |
| bool "S3C2410 PM Suspend debug" |
| depends on PLAT_S3C && PM |
| help |
| Say Y here if you want verbose debugging from the PM Suspend and |
| Resume code. See <file:Documentation/arm/Samsung-S3C24XX/Suspend.txt> |
| for more information. |
| |
| config S3C2410_PM_CHECK |
| bool "S3C2410 PM Suspend Memory CRC" |
| depends on PLAT_S3C && PM && CRC32 |
| help |
| Enable the PM code's memory area checksum over sleep. This option |
| will generate CRCs of all blocks of memory, and store them before |
| going to sleep. The blocks are then checked on resume for any |
| errors. |
| |
| Note, this can take several seconds depending on memory size |
| and CPU speed. |
| |
| See <file:Documentation/arm/Samsung-S3C24XX/Suspend.txt> |
| |
| config S3C2410_PM_CHECK_CHUNKSIZE |
| int "S3C2410 PM Suspend CRC Chunksize (KiB)" |
| depends on PLAT_S3C && PM && S3C2410_PM_CHECK |
| default 64 |
| help |
| Set the chunksize in Kilobytes of the CRC for checking memory |
| corruption over suspend and resume. A smaller value will mean that |
| the CRC data block will take more memory, but wil identify any |
| faults with better precision. |
| |
| See <file:Documentation/arm/Samsung-S3C24XX/Suspend.txt> |
| |
| config S3C_LOWLEVEL_UART_PORT |
| int "S3C UART to use for low-level messages" |
| depends on PLAT_S3C |
| default 0 |
| help |
| Choice of which UART port to use for the low-level messages, |
| such as the `Uncompressing...` at start time. The value of |
| this configuration should be between zero and two. The port |
| must have been initialised by the boot-loader before use. |
| |
| # options for gpiolib support |
| |
| config S3C_GPIO_SPACE |
| int "Space between gpio banks" |
| default 0 |
| help |
| Add a number of spare GPIO entries between each bank for debugging |
| purposes. This allows any problems where an counter overflows from |
| one bank to another to be caught, at the expense of using a little |
| more memory. |
| |
| config S3C_GPIO_TRACK |
| bool |
| help |
| Internal configuration option to enable the s3c specific gpio |
| chip tracking if the platform requires it. |
| |
| config S3C_GPIO_PULL_UPDOWN |
| bool |
| help |
| Internal configuration to enable the correct GPIO pull helper |
| |
| config S3C_GPIO_PULL_DOWN |
| bool |
| help |
| Internal configuration to enable the correct GPIO pull helper |
| |
| config S3C_GPIO_PULL_UP |
| bool |
| help |
| Internal configuration to enable the correct GPIO pull helper |
| |
| config S3C_GPIO_CFG_S3C24XX |
| bool |
| help |
| Internal configuration to enable S3C24XX style GPIO configuration |
| functions. |
| |
| config S3C_GPIO_CFG_S3C64XX |
| bool |
| help |
| Internal configuration to enable S3C64XX style GPIO configuration |
| functions. |
| |
| # device definitions to compile in |
| |
| config S3C_DEV_HSMMC |
| bool |
| depends on PLAT_S3C |
| help |
| Compile in platform device definitions for HSMMC code |
| |
| config S3C_DEV_HSMMC1 |
| bool |
| depends on PLAT_S3C |
| help |
| Compile in platform device definitions for HSMMC channel 1 |
| |
| config S3C_DEV_I2C1 |
| bool |
| depends on PLAT_S3C |
| help |
| Compile in platform device definitions for I2C channel 1 |
| |
| config S3C_DEV_FB |
| bool |
| depends on PLAT_S3C |
| help |
| Compile in platform device definition for framebuffer |