| /* |
| Copyright (C) 2004 - 2009 Ivo van Doorn <IvDoorn@gmail.com> |
| <http://rt2x00.serialmonkey.com> |
| |
| This program is free software; you can redistribute it and/or modify |
| it under the terms of the GNU General Public License as published by |
| the Free Software Foundation; either version 2 of the License, or |
| (at your option) any later version. |
| |
| This program is distributed in the hope that it will be useful, |
| but WITHOUT ANY WARRANTY; without even the implied warranty of |
| MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the |
| GNU General Public License for more details. |
| |
| You should have received a copy of the GNU General Public License |
| along with this program; if not, write to the |
| Free Software Foundation, Inc., |
| 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA. |
| */ |
| |
| /* |
| Module: rt61pci |
| Abstract: Data structures and registers for the rt61pci module. |
| Supported chipsets: RT2561, RT2561s, RT2661. |
| */ |
| |
| #ifndef RT61PCI_H |
| #define RT61PCI_H |
| |
| /* |
| * RT chip PCI IDs. |
| */ |
| #define RT2561s_PCI_ID 0x0301 |
| #define RT2561_PCI_ID 0x0302 |
| #define RT2661_PCI_ID 0x0401 |
| |
| /* |
| * RF chip defines. |
| */ |
| #define RF5225 0x0001 |
| #define RF5325 0x0002 |
| #define RF2527 0x0003 |
| #define RF2529 0x0004 |
| |
| /* |
| * Signal information. |
| * Default offset is required for RSSI <-> dBm conversion. |
| */ |
| #define DEFAULT_RSSI_OFFSET 120 |
| |
| /* |
| * Register layout information. |
| */ |
| #define CSR_REG_BASE 0x3000 |
| #define CSR_REG_SIZE 0x04b0 |
| #define EEPROM_BASE 0x0000 |
| #define EEPROM_SIZE 0x0100 |
| #define BBP_BASE 0x0000 |
| #define BBP_SIZE 0x0080 |
| #define RF_BASE 0x0004 |
| #define RF_SIZE 0x0010 |
| |
| /* |
| * Number of TX queues. |
| */ |
| #define NUM_TX_QUEUES 4 |
| |
| /* |
| * PCI registers. |
| */ |
| |
| /* |
| * HOST_CMD_CSR: For HOST to interrupt embedded processor |
| */ |
| #define HOST_CMD_CSR 0x0008 |
| #define HOST_CMD_CSR_HOST_COMMAND FIELD32(0x0000007f) |
| #define HOST_CMD_CSR_INTERRUPT_MCU FIELD32(0x00000080) |
| |
| /* |
| * MCU_CNTL_CSR |
| * SELECT_BANK: Select 8051 program bank. |
| * RESET: Enable 8051 reset state. |
| * READY: Ready state for 8051. |
| */ |
| #define MCU_CNTL_CSR 0x000c |
| #define MCU_CNTL_CSR_SELECT_BANK FIELD32(0x00000001) |
| #define MCU_CNTL_CSR_RESET FIELD32(0x00000002) |
| #define MCU_CNTL_CSR_READY FIELD32(0x00000004) |
| |
| /* |
| * SOFT_RESET_CSR |
| * FORCE_CLOCK_ON: Host force MAC clock ON |
| */ |
| #define SOFT_RESET_CSR 0x0010 |
| #define SOFT_RESET_CSR_FORCE_CLOCK_ON FIELD32(0x00000002) |
| |
| /* |
| * MCU_INT_SOURCE_CSR: MCU interrupt source/mask register. |
| */ |
| #define MCU_INT_SOURCE_CSR 0x0014 |
| #define MCU_INT_SOURCE_CSR_0 FIELD32(0x00000001) |
| #define MCU_INT_SOURCE_CSR_1 FIELD32(0x00000002) |
| #define MCU_INT_SOURCE_CSR_2 FIELD32(0x00000004) |
| #define MCU_INT_SOURCE_CSR_3 FIELD32(0x00000008) |
| #define MCU_INT_SOURCE_CSR_4 FIELD32(0x00000010) |
| #define MCU_INT_SOURCE_CSR_5 FIELD32(0x00000020) |
| #define MCU_INT_SOURCE_CSR_6 FIELD32(0x00000040) |
| #define MCU_INT_SOURCE_CSR_7 FIELD32(0x00000080) |
| #define MCU_INT_SOURCE_CSR_TWAKEUP FIELD32(0x00000100) |
| #define MCU_INT_SOURCE_CSR_TBTT_EXPIRE FIELD32(0x00000200) |
| |
| /* |
| * MCU_INT_MASK_CSR: MCU interrupt source/mask register. |
| */ |
| #define MCU_INT_MASK_CSR 0x0018 |
| #define MCU_INT_MASK_CSR_0 FIELD32(0x00000001) |
| #define MCU_INT_MASK_CSR_1 FIELD32(0x00000002) |
| #define MCU_INT_MASK_CSR_2 FIELD32(0x00000004) |
| #define MCU_INT_MASK_CSR_3 FIELD32(0x00000008) |
| #define MCU_INT_MASK_CSR_4 FIELD32(0x00000010) |
| #define MCU_INT_MASK_CSR_5 FIELD32(0x00000020) |
| #define MCU_INT_MASK_CSR_6 FIELD32(0x00000040) |
| #define MCU_INT_MASK_CSR_7 FIELD32(0x00000080) |
| #define MCU_INT_MASK_CSR_TWAKEUP FIELD32(0x00000100) |
| #define MCU_INT_MASK_CSR_TBTT_EXPIRE FIELD32(0x00000200) |
| |
| /* |
| * PCI_USEC_CSR |
| */ |
| #define PCI_USEC_CSR 0x001c |
| |
| /* |
| * Security key table memory. |
| * 16 entries 32-byte for shared key table |
| * 64 entries 32-byte for pairwise key table |
| * 64 entries 8-byte for pairwise ta key table |
| */ |
| #define SHARED_KEY_TABLE_BASE 0x1000 |
| #define PAIRWISE_KEY_TABLE_BASE 0x1200 |
| #define PAIRWISE_TA_TABLE_BASE 0x1a00 |
| |
| #define SHARED_KEY_ENTRY(__idx) \ |
| ( SHARED_KEY_TABLE_BASE + \ |
| ((__idx) * sizeof(struct hw_key_entry)) ) |
| #define PAIRWISE_KEY_ENTRY(__idx) \ |
| ( PAIRWISE_KEY_TABLE_BASE + \ |
| ((__idx) * sizeof(struct hw_key_entry)) ) |
| #define PAIRWISE_TA_ENTRY(__idx) \ |
| ( PAIRWISE_TA_TABLE_BASE + \ |
| ((__idx) * sizeof(struct hw_pairwise_ta_entry)) ) |
| |
| struct hw_key_entry { |
| u8 key[16]; |
| u8 tx_mic[8]; |
| u8 rx_mic[8]; |
| } __packed; |
| |
| struct hw_pairwise_ta_entry { |
| u8 address[6]; |
| u8 cipher; |
| u8 reserved; |
| } __packed; |
| |
| /* |
| * Other on-chip shared memory space. |
| */ |
| #define HW_CIS_BASE 0x2000 |
| #define HW_NULL_BASE 0x2b00 |
| |
| /* |
| * Since NULL frame won't be that long (256 byte), |
| * We steal 16 tail bytes to save debugging settings. |
| */ |
| #define HW_DEBUG_SETTING_BASE 0x2bf0 |
| |
| /* |
| * On-chip BEACON frame space. |
| */ |
| #define HW_BEACON_BASE0 0x2c00 |
| #define HW_BEACON_BASE1 0x2d00 |
| #define HW_BEACON_BASE2 0x2e00 |
| #define HW_BEACON_BASE3 0x2f00 |
| |
| #define HW_BEACON_OFFSET(__index) \ |
| ( HW_BEACON_BASE0 + (__index * 0x0100) ) |
| |
| /* |
| * HOST-MCU shared memory. |
| */ |
| |
| /* |
| * H2M_MAILBOX_CSR: Host-to-MCU Mailbox. |
| */ |
| #define H2M_MAILBOX_CSR 0x2100 |
| #define H2M_MAILBOX_CSR_ARG0 FIELD32(0x000000ff) |
| #define H2M_MAILBOX_CSR_ARG1 FIELD32(0x0000ff00) |
| #define H2M_MAILBOX_CSR_CMD_TOKEN FIELD32(0x00ff0000) |
| #define H2M_MAILBOX_CSR_OWNER FIELD32(0xff000000) |
| |
| /* |
| * MCU_LEDCS: LED control for MCU Mailbox. |
| */ |
| #define MCU_LEDCS_LED_MODE FIELD16(0x001f) |
| #define MCU_LEDCS_RADIO_STATUS FIELD16(0x0020) |
| #define MCU_LEDCS_LINK_BG_STATUS FIELD16(0x0040) |
| #define MCU_LEDCS_LINK_A_STATUS FIELD16(0x0080) |
| #define MCU_LEDCS_POLARITY_GPIO_0 FIELD16(0x0100) |
| #define MCU_LEDCS_POLARITY_GPIO_1 FIELD16(0x0200) |
| #define MCU_LEDCS_POLARITY_GPIO_2 FIELD16(0x0400) |
| #define MCU_LEDCS_POLARITY_GPIO_3 FIELD16(0x0800) |
| #define MCU_LEDCS_POLARITY_GPIO_4 FIELD16(0x1000) |
| #define MCU_LEDCS_POLARITY_ACT FIELD16(0x2000) |
| #define MCU_LEDCS_POLARITY_READY_BG FIELD16(0x4000) |
| #define MCU_LEDCS_POLARITY_READY_A FIELD16(0x8000) |
| |
| /* |
| * M2H_CMD_DONE_CSR. |
| */ |
| #define M2H_CMD_DONE_CSR 0x2104 |
| |
| /* |
| * MCU_TXOP_ARRAY_BASE. |
| */ |
| #define MCU_TXOP_ARRAY_BASE 0x2110 |
| |
| /* |
| * MAC Control/Status Registers(CSR). |
| * Some values are set in TU, whereas 1 TU == 1024 us. |
| */ |
| |
| /* |
| * MAC_CSR0: ASIC revision number. |
| */ |
| #define MAC_CSR0 0x3000 |
| #define MAC_CSR0_REVISION FIELD32(0x0000000f) |
| #define MAC_CSR0_CHIPSET FIELD32(0x000ffff0) |
| |
| /* |
| * MAC_CSR1: System control register. |
| * SOFT_RESET: Software reset bit, 1: reset, 0: normal. |
| * BBP_RESET: Hardware reset BBP. |
| * HOST_READY: Host is ready after initialization, 1: ready. |
| */ |
| #define MAC_CSR1 0x3004 |
| #define MAC_CSR1_SOFT_RESET FIELD32(0x00000001) |
| #define MAC_CSR1_BBP_RESET FIELD32(0x00000002) |
| #define MAC_CSR1_HOST_READY FIELD32(0x00000004) |
| |
| /* |
| * MAC_CSR2: STA MAC register 0. |
| */ |
| #define MAC_CSR2 0x3008 |
| #define MAC_CSR2_BYTE0 FIELD32(0x000000ff) |
| #define MAC_CSR2_BYTE1 FIELD32(0x0000ff00) |
| #define MAC_CSR2_BYTE2 FIELD32(0x00ff0000) |
| #define MAC_CSR2_BYTE3 FIELD32(0xff000000) |
| |
| /* |
| * MAC_CSR3: STA MAC register 1. |
| * UNICAST_TO_ME_MASK: |
| * Used to mask off bits from byte 5 of the MAC address |
| * to determine the UNICAST_TO_ME bit for RX frames. |
| * The full mask is complemented by BSS_ID_MASK: |
| * MASK = BSS_ID_MASK & UNICAST_TO_ME_MASK |
| */ |
| #define MAC_CSR3 0x300c |
| #define MAC_CSR3_BYTE4 FIELD32(0x000000ff) |
| #define MAC_CSR3_BYTE5 FIELD32(0x0000ff00) |
| #define MAC_CSR3_UNICAST_TO_ME_MASK FIELD32(0x00ff0000) |
| |
| /* |
| * MAC_CSR4: BSSID register 0. |
| */ |
| #define MAC_CSR4 0x3010 |
| #define MAC_CSR4_BYTE0 FIELD32(0x000000ff) |
| #define MAC_CSR4_BYTE1 FIELD32(0x0000ff00) |
| #define MAC_CSR4_BYTE2 FIELD32(0x00ff0000) |
| #define MAC_CSR4_BYTE3 FIELD32(0xff000000) |
| |
| /* |
| * MAC_CSR5: BSSID register 1. |
| * BSS_ID_MASK: |
| * This mask is used to mask off bits 0 and 1 of byte 5 of the |
| * BSSID. This will make sure that those bits will be ignored |
| * when determining the MY_BSS of RX frames. |
| * 0: 1-BSSID mode (BSS index = 0) |
| * 1: 2-BSSID mode (BSS index: Byte5, bit 0) |
| * 2: 2-BSSID mode (BSS index: byte5, bit 1) |
| * 3: 4-BSSID mode (BSS index: byte5, bit 0 - 1) |
| */ |
| #define MAC_CSR5 0x3014 |
| #define MAC_CSR5_BYTE4 FIELD32(0x000000ff) |
| #define MAC_CSR5_BYTE5 FIELD32(0x0000ff00) |
| #define MAC_CSR5_BSS_ID_MASK FIELD32(0x00ff0000) |
| |
| /* |
| * MAC_CSR6: Maximum frame length register. |
| */ |
| #define MAC_CSR6 0x3018 |
| #define MAC_CSR6_MAX_FRAME_UNIT FIELD32(0x00000fff) |
| |
| /* |
| * MAC_CSR7: Reserved |
| */ |
| #define MAC_CSR7 0x301c |
| |
| /* |
| * MAC_CSR8: SIFS/EIFS register. |
| * All units are in US. |
| */ |
| #define MAC_CSR8 0x3020 |
| #define MAC_CSR8_SIFS FIELD32(0x000000ff) |
| #define MAC_CSR8_SIFS_AFTER_RX_OFDM FIELD32(0x0000ff00) |
| #define MAC_CSR8_EIFS FIELD32(0xffff0000) |
| |
| /* |
| * MAC_CSR9: Back-Off control register. |
| * SLOT_TIME: Slot time, default is 20us for 802.11BG. |
| * CWMIN: Bit for Cwmin. default Cwmin is 31 (2^5 - 1). |
| * CWMAX: Bit for Cwmax, default Cwmax is 1023 (2^10 - 1). |
| * CW_SELECT: 1: CWmin/Cwmax select from register, 0:select from TxD. |
| */ |
| #define MAC_CSR9 0x3024 |
| #define MAC_CSR9_SLOT_TIME FIELD32(0x000000ff) |
| #define MAC_CSR9_CWMIN FIELD32(0x00000f00) |
| #define MAC_CSR9_CWMAX FIELD32(0x0000f000) |
| #define MAC_CSR9_CW_SELECT FIELD32(0x00010000) |
| |
| /* |
| * MAC_CSR10: Power state configuration. |
| */ |
| #define MAC_CSR10 0x3028 |
| |
| /* |
| * MAC_CSR11: Power saving transition time register. |
| * DELAY_AFTER_TBCN: Delay after Tbcn expired in units of TU. |
| * TBCN_BEFORE_WAKEUP: Number of beacon before wakeup. |
| * WAKEUP_LATENCY: In unit of TU. |
| */ |
| #define MAC_CSR11 0x302c |
| #define MAC_CSR11_DELAY_AFTER_TBCN FIELD32(0x000000ff) |
| #define MAC_CSR11_TBCN_BEFORE_WAKEUP FIELD32(0x00007f00) |
| #define MAC_CSR11_AUTOWAKE FIELD32(0x00008000) |
| #define MAC_CSR11_WAKEUP_LATENCY FIELD32(0x000f0000) |
| |
| /* |
| * MAC_CSR12: Manual power control / status register (merge CSR20 & PWRCSR1). |
| * CURRENT_STATE: 0:sleep, 1:awake. |
| * FORCE_WAKEUP: This has higher priority than PUT_TO_SLEEP. |
| * BBP_CURRENT_STATE: 0: BBP sleep, 1: BBP awake. |
| */ |
| #define MAC_CSR12 0x3030 |
| #define MAC_CSR12_CURRENT_STATE FIELD32(0x00000001) |
| #define MAC_CSR12_PUT_TO_SLEEP FIELD32(0x00000002) |
| #define MAC_CSR12_FORCE_WAKEUP FIELD32(0x00000004) |
| #define MAC_CSR12_BBP_CURRENT_STATE FIELD32(0x00000008) |
| |
| /* |
| * MAC_CSR13: GPIO. |
| */ |
| #define MAC_CSR13 0x3034 |
| #define MAC_CSR13_BIT0 FIELD32(0x00000001) |
| #define MAC_CSR13_BIT1 FIELD32(0x00000002) |
| #define MAC_CSR13_BIT2 FIELD32(0x00000004) |
| #define MAC_CSR13_BIT3 FIELD32(0x00000008) |
| #define MAC_CSR13_BIT4 FIELD32(0x00000010) |
| #define MAC_CSR13_BIT5 FIELD32(0x00000020) |
| #define MAC_CSR13_BIT6 FIELD32(0x00000040) |
| #define MAC_CSR13_BIT7 FIELD32(0x00000080) |
| #define MAC_CSR13_BIT8 FIELD32(0x00000100) |
| #define MAC_CSR13_BIT9 FIELD32(0x00000200) |
| #define MAC_CSR13_BIT10 FIELD32(0x00000400) |
| #define MAC_CSR13_BIT11 FIELD32(0x00000800) |
| #define MAC_CSR13_BIT12 FIELD32(0x00001000) |
| #define MAC_CSR13_BIT13 FIELD32(0x00002000) |
| |
| /* |
| * MAC_CSR14: LED control register. |
| * ON_PERIOD: On period, default 70ms. |
| * OFF_PERIOD: Off period, default 30ms. |
| * HW_LED: HW TX activity, 1: normal OFF, 0: normal ON. |
| * SW_LED: s/w LED, 1: ON, 0: OFF. |
| * HW_LED_POLARITY: 0: active low, 1: active high. |
| */ |
| #define MAC_CSR14 0x3038 |
| #define MAC_CSR14_ON_PERIOD FIELD32(0x000000ff) |
| #define MAC_CSR14_OFF_PERIOD FIELD32(0x0000ff00) |
| #define MAC_CSR14_HW_LED FIELD32(0x00010000) |
| #define MAC_CSR14_SW_LED FIELD32(0x00020000) |
| #define MAC_CSR14_HW_LED_POLARITY FIELD32(0x00040000) |
| #define MAC_CSR14_SW_LED2 FIELD32(0x00080000) |
| |
| /* |
| * MAC_CSR15: NAV control. |
| */ |
| #define MAC_CSR15 0x303c |
| |
| /* |
| * TXRX control registers. |
| * Some values are set in TU, whereas 1 TU == 1024 us. |
| */ |
| |
| /* |
| * TXRX_CSR0: TX/RX configuration register. |
| * TSF_OFFSET: Default is 24. |
| * AUTO_TX_SEQ: 1: ASIC auto replace sequence nr in outgoing frame. |
| * DISABLE_RX: Disable Rx engine. |
| * DROP_CRC: Drop CRC error. |
| * DROP_PHYSICAL: Drop physical error. |
| * DROP_CONTROL: Drop control frame. |
| * DROP_NOT_TO_ME: Drop not to me unicast frame. |
| * DROP_TO_DS: Drop fram ToDs bit is true. |
| * DROP_VERSION_ERROR: Drop version error frame. |
| * DROP_MULTICAST: Drop multicast frames. |
| * DROP_BORADCAST: Drop broadcast frames. |
| * DROP_ACK_CTS: Drop received ACK and CTS. |
| */ |
| #define TXRX_CSR0 0x3040 |
| #define TXRX_CSR0_RX_ACK_TIMEOUT FIELD32(0x000001ff) |
| #define TXRX_CSR0_TSF_OFFSET FIELD32(0x00007e00) |
| #define TXRX_CSR0_AUTO_TX_SEQ FIELD32(0x00008000) |
| #define TXRX_CSR0_DISABLE_RX FIELD32(0x00010000) |
| #define TXRX_CSR0_DROP_CRC FIELD32(0x00020000) |
| #define TXRX_CSR0_DROP_PHYSICAL FIELD32(0x00040000) |
| #define TXRX_CSR0_DROP_CONTROL FIELD32(0x00080000) |
| #define TXRX_CSR0_DROP_NOT_TO_ME FIELD32(0x00100000) |
| #define TXRX_CSR0_DROP_TO_DS FIELD32(0x00200000) |
| #define TXRX_CSR0_DROP_VERSION_ERROR FIELD32(0x00400000) |
| #define TXRX_CSR0_DROP_MULTICAST FIELD32(0x00800000) |
| #define TXRX_CSR0_DROP_BROADCAST FIELD32(0x01000000) |
| #define TXRX_CSR0_DROP_ACK_CTS FIELD32(0x02000000) |
| #define TXRX_CSR0_TX_WITHOUT_WAITING FIELD32(0x04000000) |
| |
| /* |
| * TXRX_CSR1 |
| */ |
| #define TXRX_CSR1 0x3044 |
| #define TXRX_CSR1_BBP_ID0 FIELD32(0x0000007f) |
| #define TXRX_CSR1_BBP_ID0_VALID FIELD32(0x00000080) |
| #define TXRX_CSR1_BBP_ID1 FIELD32(0x00007f00) |
| #define TXRX_CSR1_BBP_ID1_VALID FIELD32(0x00008000) |
| #define TXRX_CSR1_BBP_ID2 FIELD32(0x007f0000) |
| #define TXRX_CSR1_BBP_ID2_VALID FIELD32(0x00800000) |
| #define TXRX_CSR1_BBP_ID3 FIELD32(0x7f000000) |
| #define TXRX_CSR1_BBP_ID3_VALID FIELD32(0x80000000) |
| |
| /* |
| * TXRX_CSR2 |
| */ |
| #define TXRX_CSR2 0x3048 |
| #define TXRX_CSR2_BBP_ID0 FIELD32(0x0000007f) |
| #define TXRX_CSR2_BBP_ID0_VALID FIELD32(0x00000080) |
| #define TXRX_CSR2_BBP_ID1 FIELD32(0x00007f00) |
| #define TXRX_CSR2_BBP_ID1_VALID FIELD32(0x00008000) |
| #define TXRX_CSR2_BBP_ID2 FIELD32(0x007f0000) |
| #define TXRX_CSR2_BBP_ID2_VALID FIELD32(0x00800000) |
| #define TXRX_CSR2_BBP_ID3 FIELD32(0x7f000000) |
| #define TXRX_CSR2_BBP_ID3_VALID FIELD32(0x80000000) |
| |
| /* |
| * TXRX_CSR3 |
| */ |
| #define TXRX_CSR3 0x304c |
| #define TXRX_CSR3_BBP_ID0 FIELD32(0x0000007f) |
| #define TXRX_CSR3_BBP_ID0_VALID FIELD32(0x00000080) |
| #define TXRX_CSR3_BBP_ID1 FIELD32(0x00007f00) |
| #define TXRX_CSR3_BBP_ID1_VALID FIELD32(0x00008000) |
| #define TXRX_CSR3_BBP_ID2 FIELD32(0x007f0000) |
| #define TXRX_CSR3_BBP_ID2_VALID FIELD32(0x00800000) |
| #define TXRX_CSR3_BBP_ID3 FIELD32(0x7f000000) |
| #define TXRX_CSR3_BBP_ID3_VALID FIELD32(0x80000000) |
| |
| /* |
| * TXRX_CSR4: Auto-Responder/Tx-retry register. |
| * AUTORESPOND_PREAMBLE: 0:long, 1:short preamble. |
| * OFDM_TX_RATE_DOWN: 1:enable. |
| * OFDM_TX_RATE_STEP: 0:1-step, 1: 2-step, 2:3-step, 3:4-step. |
| * OFDM_TX_FALLBACK_CCK: 0: Fallback to OFDM 6M only, 1: Fallback to CCK 1M,2M. |
| */ |
| #define TXRX_CSR4 0x3050 |
| #define TXRX_CSR4_TX_ACK_TIMEOUT FIELD32(0x000000ff) |
| #define TXRX_CSR4_CNTL_ACK_POLICY FIELD32(0x00000700) |
| #define TXRX_CSR4_ACK_CTS_PSM FIELD32(0x00010000) |
| #define TXRX_CSR4_AUTORESPOND_ENABLE FIELD32(0x00020000) |
| #define TXRX_CSR4_AUTORESPOND_PREAMBLE FIELD32(0x00040000) |
| #define TXRX_CSR4_OFDM_TX_RATE_DOWN FIELD32(0x00080000) |
| #define TXRX_CSR4_OFDM_TX_RATE_STEP FIELD32(0x00300000) |
| #define TXRX_CSR4_OFDM_TX_FALLBACK_CCK FIELD32(0x00400000) |
| #define TXRX_CSR4_LONG_RETRY_LIMIT FIELD32(0x0f000000) |
| #define TXRX_CSR4_SHORT_RETRY_LIMIT FIELD32(0xf0000000) |
| |
| /* |
| * TXRX_CSR5 |
| */ |
| #define TXRX_CSR5 0x3054 |
| |
| /* |
| * TXRX_CSR6: ACK/CTS payload consumed time |
| */ |
| #define TXRX_CSR6 0x3058 |
| |
| /* |
| * TXRX_CSR7: OFDM ACK/CTS payload consumed time for 6/9/12/18 mbps. |
| */ |
| #define TXRX_CSR7 0x305c |
| #define TXRX_CSR7_ACK_CTS_6MBS FIELD32(0x000000ff) |
| #define TXRX_CSR7_ACK_CTS_9MBS FIELD32(0x0000ff00) |
| #define TXRX_CSR7_ACK_CTS_12MBS FIELD32(0x00ff0000) |
| #define TXRX_CSR7_ACK_CTS_18MBS FIELD32(0xff000000) |
| |
| /* |
| * TXRX_CSR8: OFDM ACK/CTS payload consumed time for 24/36/48/54 mbps. |
| */ |
| #define TXRX_CSR8 0x3060 |
| #define TXRX_CSR8_ACK_CTS_24MBS FIELD32(0x000000ff) |
| #define TXRX_CSR8_ACK_CTS_36MBS FIELD32(0x0000ff00) |
| #define TXRX_CSR8_ACK_CTS_48MBS FIELD32(0x00ff0000) |
| #define TXRX_CSR8_ACK_CTS_54MBS FIELD32(0xff000000) |
| |
| /* |
| * TXRX_CSR9: Synchronization control register. |
| * BEACON_INTERVAL: In unit of 1/16 TU. |
| * TSF_TICKING: Enable TSF auto counting. |
| * TSF_SYNC: Tsf sync, 0: disable, 1: infra, 2: ad-hoc/master mode. |
| * BEACON_GEN: Enable beacon generator. |
| */ |
| #define TXRX_CSR9 0x3064 |
| #define TXRX_CSR9_BEACON_INTERVAL FIELD32(0x0000ffff) |
| #define TXRX_CSR9_TSF_TICKING FIELD32(0x00010000) |
| #define TXRX_CSR9_TSF_SYNC FIELD32(0x00060000) |
| #define TXRX_CSR9_TBTT_ENABLE FIELD32(0x00080000) |
| #define TXRX_CSR9_BEACON_GEN FIELD32(0x00100000) |
| #define TXRX_CSR9_TIMESTAMP_COMPENSATE FIELD32(0xff000000) |
| |
| /* |
| * TXRX_CSR10: BEACON alignment. |
| */ |
| #define TXRX_CSR10 0x3068 |
| |
| /* |
| * TXRX_CSR11: AES mask. |
| */ |
| #define TXRX_CSR11 0x306c |
| |
| /* |
| * TXRX_CSR12: TSF low 32. |
| */ |
| #define TXRX_CSR12 0x3070 |
| #define TXRX_CSR12_LOW_TSFTIMER FIELD32(0xffffffff) |
| |
| /* |
| * TXRX_CSR13: TSF high 32. |
| */ |
| #define TXRX_CSR13 0x3074 |
| #define TXRX_CSR13_HIGH_TSFTIMER FIELD32(0xffffffff) |
| |
| /* |
| * TXRX_CSR14: TBTT timer. |
| */ |
| #define TXRX_CSR14 0x3078 |
| |
| /* |
| * TXRX_CSR15: TKIP MIC priority byte "AND" mask. |
| */ |
| #define TXRX_CSR15 0x307c |
| |
| /* |
| * PHY control registers. |
| * Some values are set in TU, whereas 1 TU == 1024 us. |
| */ |
| |
| /* |
| * PHY_CSR0: RF/PS control. |
| */ |
| #define PHY_CSR0 0x3080 |
| #define PHY_CSR0_PA_PE_BG FIELD32(0x00010000) |
| #define PHY_CSR0_PA_PE_A FIELD32(0x00020000) |
| |
| /* |
| * PHY_CSR1 |
| */ |
| #define PHY_CSR1 0x3084 |
| |
| /* |
| * PHY_CSR2: Pre-TX BBP control. |
| */ |
| #define PHY_CSR2 0x3088 |
| |
| /* |
| * PHY_CSR3: BBP serial control register. |
| * VALUE: Register value to program into BBP. |
| * REG_NUM: Selected BBP register. |
| * READ_CONTROL: 0: Write BBP, 1: Read BBP. |
| * BUSY: 1: ASIC is busy execute BBP programming. |
| */ |
| #define PHY_CSR3 0x308c |
| #define PHY_CSR3_VALUE FIELD32(0x000000ff) |
| #define PHY_CSR3_REGNUM FIELD32(0x00007f00) |
| #define PHY_CSR3_READ_CONTROL FIELD32(0x00008000) |
| #define PHY_CSR3_BUSY FIELD32(0x00010000) |
| |
| /* |
| * PHY_CSR4: RF serial control register |
| * VALUE: Register value (include register id) serial out to RF/IF chip. |
| * NUMBER_OF_BITS: Number of bits used in RFRegValue (I:20, RFMD:22). |
| * IF_SELECT: 1: select IF to program, 0: select RF to program. |
| * PLL_LD: RF PLL_LD status. |
| * BUSY: 1: ASIC is busy execute RF programming. |
| */ |
| #define PHY_CSR4 0x3090 |
| #define PHY_CSR4_VALUE FIELD32(0x00ffffff) |
| #define PHY_CSR4_NUMBER_OF_BITS FIELD32(0x1f000000) |
| #define PHY_CSR4_IF_SELECT FIELD32(0x20000000) |
| #define PHY_CSR4_PLL_LD FIELD32(0x40000000) |
| #define PHY_CSR4_BUSY FIELD32(0x80000000) |
| |
| /* |
| * PHY_CSR5: RX to TX signal switch timing control. |
| */ |
| #define PHY_CSR5 0x3094 |
| #define PHY_CSR5_IQ_FLIP FIELD32(0x00000004) |
| |
| /* |
| * PHY_CSR6: TX to RX signal timing control. |
| */ |
| #define PHY_CSR6 0x3098 |
| #define PHY_CSR6_IQ_FLIP FIELD32(0x00000004) |
| |
| /* |
| * PHY_CSR7: TX DAC switching timing control. |
| */ |
| #define PHY_CSR7 0x309c |
| |
| /* |
| * Security control register. |
| */ |
| |
| /* |
| * SEC_CSR0: Shared key table control. |
| */ |
| #define SEC_CSR0 0x30a0 |
| #define SEC_CSR0_BSS0_KEY0_VALID FIELD32(0x00000001) |
| #define SEC_CSR0_BSS0_KEY1_VALID FIELD32(0x00000002) |
| #define SEC_CSR0_BSS0_KEY2_VALID FIELD32(0x00000004) |
| #define SEC_CSR0_BSS0_KEY3_VALID FIELD32(0x00000008) |
| #define SEC_CSR0_BSS1_KEY0_VALID FIELD32(0x00000010) |
| #define SEC_CSR0_BSS1_KEY1_VALID FIELD32(0x00000020) |
| #define SEC_CSR0_BSS1_KEY2_VALID FIELD32(0x00000040) |
| #define SEC_CSR0_BSS1_KEY3_VALID FIELD32(0x00000080) |
| #define SEC_CSR0_BSS2_KEY0_VALID FIELD32(0x00000100) |
| #define SEC_CSR0_BSS2_KEY1_VALID FIELD32(0x00000200) |
| #define SEC_CSR0_BSS2_KEY2_VALID FIELD32(0x00000400) |
| #define SEC_CSR0_BSS2_KEY3_VALID FIELD32(0x00000800) |
| #define SEC_CSR0_BSS3_KEY0_VALID FIELD32(0x00001000) |
| #define SEC_CSR0_BSS3_KEY1_VALID FIELD32(0x00002000) |
| #define SEC_CSR0_BSS3_KEY2_VALID FIELD32(0x00004000) |
| #define SEC_CSR0_BSS3_KEY3_VALID FIELD32(0x00008000) |
| |
| /* |
| * SEC_CSR1: Shared key table security mode register. |
| */ |
| #define SEC_CSR1 0x30a4 |
| #define SEC_CSR1_BSS0_KEY0_CIPHER_ALG FIELD32(0x00000007) |
| #define SEC_CSR1_BSS0_KEY1_CIPHER_ALG FIELD32(0x00000070) |
| #define SEC_CSR1_BSS0_KEY2_CIPHER_ALG FIELD32(0x00000700) |
| #define SEC_CSR1_BSS0_KEY3_CIPHER_ALG FIELD32(0x00007000) |
| #define SEC_CSR1_BSS1_KEY0_CIPHER_ALG FIELD32(0x00070000) |
| #define SEC_CSR1_BSS1_KEY1_CIPHER_ALG FIELD32(0x00700000) |
| #define SEC_CSR1_BSS1_KEY2_CIPHER_ALG FIELD32(0x07000000) |
| #define SEC_CSR1_BSS1_KEY3_CIPHER_ALG FIELD32(0x70000000) |
| |
| /* |
| * Pairwise key table valid bitmap registers. |
| * SEC_CSR2: pairwise key table valid bitmap 0. |
| * SEC_CSR3: pairwise key table valid bitmap 1. |
| */ |
| #define SEC_CSR2 0x30a8 |
| #define SEC_CSR3 0x30ac |
| |
| /* |
| * SEC_CSR4: Pairwise key table lookup control. |
| */ |
| #define SEC_CSR4 0x30b0 |
| #define SEC_CSR4_ENABLE_BSS0 FIELD32(0x00000001) |
| #define SEC_CSR4_ENABLE_BSS1 FIELD32(0x00000002) |
| #define SEC_CSR4_ENABLE_BSS2 FIELD32(0x00000004) |
| #define SEC_CSR4_ENABLE_BSS3 FIELD32(0x00000008) |
| |
| /* |
| * SEC_CSR5: shared key table security mode register. |
| */ |
| #define SEC_CSR5 0x30b4 |
| #define SEC_CSR5_BSS2_KEY0_CIPHER_ALG FIELD32(0x00000007) |
| #define SEC_CSR5_BSS2_KEY1_CIPHER_ALG FIELD32(0x00000070) |
| #define SEC_CSR5_BSS2_KEY2_CIPHER_ALG FIELD32(0x00000700) |
| #define SEC_CSR5_BSS2_KEY3_CIPHER_ALG FIELD32(0x00007000) |
| #define SEC_CSR5_BSS3_KEY0_CIPHER_ALG FIELD32(0x00070000) |
| #define SEC_CSR5_BSS3_KEY1_CIPHER_ALG FIELD32(0x00700000) |
| #define SEC_CSR5_BSS3_KEY2_CIPHER_ALG FIELD32(0x07000000) |
| #define SEC_CSR5_BSS3_KEY3_CIPHER_ALG FIELD32(0x70000000) |
| |
| /* |
| * STA control registers. |
| */ |
| |
| /* |
| * STA_CSR0: RX PLCP error count & RX FCS error count. |
| */ |
| #define STA_CSR0 0x30c0 |
| #define STA_CSR0_FCS_ERROR FIELD32(0x0000ffff) |
| #define STA_CSR0_PLCP_ERROR FIELD32(0xffff0000) |
| |
| /* |
| * STA_CSR1: RX False CCA count & RX LONG frame count. |
| */ |
| #define STA_CSR1 0x30c4 |
| #define STA_CSR1_PHYSICAL_ERROR FIELD32(0x0000ffff) |
| #define STA_CSR1_FALSE_CCA_ERROR FIELD32(0xffff0000) |
| |
| /* |
| * STA_CSR2: TX Beacon count and RX FIFO overflow count. |
| */ |
| #define STA_CSR2 0x30c8 |
| #define STA_CSR2_RX_FIFO_OVERFLOW_COUNT FIELD32(0x0000ffff) |
| #define STA_CSR2_RX_OVERFLOW_COUNT FIELD32(0xffff0000) |
| |
| /* |
| * STA_CSR3: TX Beacon count. |
| */ |
| #define STA_CSR3 0x30cc |
| #define STA_CSR3_TX_BEACON_COUNT FIELD32(0x0000ffff) |
| |
| /* |
| * STA_CSR4: TX Result status register. |
| * VALID: 1:This register contains a valid TX result. |
| */ |
| #define STA_CSR4 0x30d0 |
| #define STA_CSR4_VALID FIELD32(0x00000001) |
| #define STA_CSR4_TX_RESULT FIELD32(0x0000000e) |
| #define STA_CSR4_RETRY_COUNT FIELD32(0x000000f0) |
| #define STA_CSR4_PID_SUBTYPE FIELD32(0x00001f00) |
| #define STA_CSR4_PID_TYPE FIELD32(0x0000e000) |
| #define STA_CSR4_TXRATE FIELD32(0x000f0000) |
| |
| /* |
| * QOS control registers. |
| */ |
| |
| /* |
| * QOS_CSR0: TXOP holder MAC address register. |
| */ |
| #define QOS_CSR0 0x30e0 |
| #define QOS_CSR0_BYTE0 FIELD32(0x000000ff) |
| #define QOS_CSR0_BYTE1 FIELD32(0x0000ff00) |
| #define QOS_CSR0_BYTE2 FIELD32(0x00ff0000) |
| #define QOS_CSR0_BYTE3 FIELD32(0xff000000) |
| |
| /* |
| * QOS_CSR1: TXOP holder MAC address register. |
| */ |
| #define QOS_CSR1 0x30e4 |
| #define QOS_CSR1_BYTE4 FIELD32(0x000000ff) |
| #define QOS_CSR1_BYTE5 FIELD32(0x0000ff00) |
| |
| /* |
| * QOS_CSR2: TXOP holder timeout register. |
| */ |
| #define QOS_CSR2 0x30e8 |
| |
| /* |
| * RX QOS-CFPOLL MAC address register. |
| * QOS_CSR3: RX QOS-CFPOLL MAC address 0. |
| * QOS_CSR4: RX QOS-CFPOLL MAC address 1. |
| */ |
| #define QOS_CSR3 0x30ec |
| #define QOS_CSR4 0x30f0 |
| |
| /* |
| * QOS_CSR5: "QosControl" field of the RX QOS-CFPOLL. |
| */ |
| #define QOS_CSR5 0x30f4 |
| |
| /* |
| * Host DMA registers. |
| */ |
| |
| /* |
| * AC0_BASE_CSR: AC_VO base address. |
| */ |
| #define AC0_BASE_CSR 0x3400 |
| #define AC0_BASE_CSR_RING_REGISTER FIELD32(0xffffffff) |
| |
| /* |
| * AC1_BASE_CSR: AC_VI base address. |
| */ |
| #define AC1_BASE_CSR 0x3404 |
| #define AC1_BASE_CSR_RING_REGISTER FIELD32(0xffffffff) |
| |
| /* |
| * AC2_BASE_CSR: AC_BE base address. |
| */ |
| #define AC2_BASE_CSR 0x3408 |
| #define AC2_BASE_CSR_RING_REGISTER FIELD32(0xffffffff) |
| |
| /* |
| * AC3_BASE_CSR: AC_BK base address. |
| */ |
| #define AC3_BASE_CSR 0x340c |
| #define AC3_BASE_CSR_RING_REGISTER FIELD32(0xffffffff) |
| |
| /* |
| * MGMT_BASE_CSR: MGMT ring base address. |
| */ |
| #define MGMT_BASE_CSR 0x3410 |
| #define MGMT_BASE_CSR_RING_REGISTER FIELD32(0xffffffff) |
| |
| /* |
| * TX_RING_CSR0: TX Ring size for AC_VO, AC_VI, AC_BE, AC_BK. |
| */ |
| #define TX_RING_CSR0 0x3418 |
| #define TX_RING_CSR0_AC0_RING_SIZE FIELD32(0x000000ff) |
| #define TX_RING_CSR0_AC1_RING_SIZE FIELD32(0x0000ff00) |
| #define TX_RING_CSR0_AC2_RING_SIZE FIELD32(0x00ff0000) |
| #define TX_RING_CSR0_AC3_RING_SIZE FIELD32(0xff000000) |
| |
| /* |
| * TX_RING_CSR1: TX Ring size for MGMT Ring, HCCA Ring |
| * TXD_SIZE: In unit of 32-bit. |
| */ |
| #define TX_RING_CSR1 0x341c |
| #define TX_RING_CSR1_MGMT_RING_SIZE FIELD32(0x000000ff) |
| #define TX_RING_CSR1_HCCA_RING_SIZE FIELD32(0x0000ff00) |
| #define TX_RING_CSR1_TXD_SIZE FIELD32(0x003f0000) |
| |
| /* |
| * AIFSN_CSR: AIFSN for each EDCA AC. |
| * AIFSN0: For AC_VO. |
| * AIFSN1: For AC_VI. |
| * AIFSN2: For AC_BE. |
| * AIFSN3: For AC_BK. |
| */ |
| #define AIFSN_CSR 0x3420 |
| #define AIFSN_CSR_AIFSN0 FIELD32(0x0000000f) |
| #define AIFSN_CSR_AIFSN1 FIELD32(0x000000f0) |
| #define AIFSN_CSR_AIFSN2 FIELD32(0x00000f00) |
| #define AIFSN_CSR_AIFSN3 FIELD32(0x0000f000) |
| |
| /* |
| * CWMIN_CSR: CWmin for each EDCA AC. |
| * CWMIN0: For AC_VO. |
| * CWMIN1: For AC_VI. |
| * CWMIN2: For AC_BE. |
| * CWMIN3: For AC_BK. |
| */ |
| #define CWMIN_CSR 0x3424 |
| #define CWMIN_CSR_CWMIN0 FIELD32(0x0000000f) |
| #define CWMIN_CSR_CWMIN1 FIELD32(0x000000f0) |
| #define CWMIN_CSR_CWMIN2 FIELD32(0x00000f00) |
| #define CWMIN_CSR_CWMIN3 FIELD32(0x0000f000) |
| |
| /* |
| * CWMAX_CSR: CWmax for each EDCA AC. |
| * CWMAX0: For AC_VO. |
| * CWMAX1: For AC_VI. |
| * CWMAX2: For AC_BE. |
| * CWMAX3: For AC_BK. |
| */ |
| #define CWMAX_CSR 0x3428 |
| #define CWMAX_CSR_CWMAX0 FIELD32(0x0000000f) |
| #define CWMAX_CSR_CWMAX1 FIELD32(0x000000f0) |
| #define CWMAX_CSR_CWMAX2 FIELD32(0x00000f00) |
| #define CWMAX_CSR_CWMAX3 FIELD32(0x0000f000) |
| |
| /* |
| * TX_DMA_DST_CSR: TX DMA destination |
| * 0: TX ring0, 1: TX ring1, 2: TX ring2 3: invalid |
| */ |
| #define TX_DMA_DST_CSR 0x342c |
| #define TX_DMA_DST_CSR_DEST_AC0 FIELD32(0x00000003) |
| #define TX_DMA_DST_CSR_DEST_AC1 FIELD32(0x0000000c) |
| #define TX_DMA_DST_CSR_DEST_AC2 FIELD32(0x00000030) |
| #define TX_DMA_DST_CSR_DEST_AC3 FIELD32(0x000000c0) |
| #define TX_DMA_DST_CSR_DEST_MGMT FIELD32(0x00000300) |
| |
| /* |
| * TX_CNTL_CSR: KICK/Abort TX. |
| * KICK_TX_AC0: For AC_VO. |
| * KICK_TX_AC1: For AC_VI. |
| * KICK_TX_AC2: For AC_BE. |
| * KICK_TX_AC3: For AC_BK. |
| * ABORT_TX_AC0: For AC_VO. |
| * ABORT_TX_AC1: For AC_VI. |
| * ABORT_TX_AC2: For AC_BE. |
| * ABORT_TX_AC3: For AC_BK. |
| */ |
| #define TX_CNTL_CSR 0x3430 |
| #define TX_CNTL_CSR_KICK_TX_AC0 FIELD32(0x00000001) |
| #define TX_CNTL_CSR_KICK_TX_AC1 FIELD32(0x00000002) |
| #define TX_CNTL_CSR_KICK_TX_AC2 FIELD32(0x00000004) |
| #define TX_CNTL_CSR_KICK_TX_AC3 FIELD32(0x00000008) |
| #define TX_CNTL_CSR_KICK_TX_MGMT FIELD32(0x00000010) |
| #define TX_CNTL_CSR_ABORT_TX_AC0 FIELD32(0x00010000) |
| #define TX_CNTL_CSR_ABORT_TX_AC1 FIELD32(0x00020000) |
| #define TX_CNTL_CSR_ABORT_TX_AC2 FIELD32(0x00040000) |
| #define TX_CNTL_CSR_ABORT_TX_AC3 FIELD32(0x00080000) |
| #define TX_CNTL_CSR_ABORT_TX_MGMT FIELD32(0x00100000) |
| |
| /* |
| * LOAD_TX_RING_CSR: Load RX desriptor |
| */ |
| #define LOAD_TX_RING_CSR 0x3434 |
| #define LOAD_TX_RING_CSR_LOAD_TXD_AC0 FIELD32(0x00000001) |
| #define LOAD_TX_RING_CSR_LOAD_TXD_AC1 FIELD32(0x00000002) |
| #define LOAD_TX_RING_CSR_LOAD_TXD_AC2 FIELD32(0x00000004) |
| #define LOAD_TX_RING_CSR_LOAD_TXD_AC3 FIELD32(0x00000008) |
| #define LOAD_TX_RING_CSR_LOAD_TXD_MGMT FIELD32(0x00000010) |
| |
| /* |
| * Several read-only registers, for debugging. |
| */ |
| #define AC0_TXPTR_CSR 0x3438 |
| #define AC1_TXPTR_CSR 0x343c |
| #define AC2_TXPTR_CSR 0x3440 |
| #define AC3_TXPTR_CSR 0x3444 |
| #define MGMT_TXPTR_CSR 0x3448 |
| |
| /* |
| * RX_BASE_CSR |
| */ |
| #define RX_BASE_CSR 0x3450 |
| #define RX_BASE_CSR_RING_REGISTER FIELD32(0xffffffff) |
| |
| /* |
| * RX_RING_CSR. |
| * RXD_SIZE: In unit of 32-bit. |
| */ |
| #define RX_RING_CSR 0x3454 |
| #define RX_RING_CSR_RING_SIZE FIELD32(0x000000ff) |
| #define RX_RING_CSR_RXD_SIZE FIELD32(0x00003f00) |
| #define RX_RING_CSR_RXD_WRITEBACK_SIZE FIELD32(0x00070000) |
| |
| /* |
| * RX_CNTL_CSR |
| */ |
| #define RX_CNTL_CSR 0x3458 |
| #define RX_CNTL_CSR_ENABLE_RX_DMA FIELD32(0x00000001) |
| #define RX_CNTL_CSR_LOAD_RXD FIELD32(0x00000002) |
| |
| /* |
| * RXPTR_CSR: Read-only, for debugging. |
| */ |
| #define RXPTR_CSR 0x345c |
| |
| /* |
| * PCI_CFG_CSR |
| */ |
| #define PCI_CFG_CSR 0x3460 |
| |
| /* |
| * BUF_FORMAT_CSR |
| */ |
| #define BUF_FORMAT_CSR 0x3464 |
| |
| /* |
| * INT_SOURCE_CSR: Interrupt source register. |
| * Write one to clear corresponding bit. |
| */ |
| #define INT_SOURCE_CSR 0x3468 |
| #define INT_SOURCE_CSR_TXDONE FIELD32(0x00000001) |
| #define INT_SOURCE_CSR_RXDONE FIELD32(0x00000002) |
| #define INT_SOURCE_CSR_BEACON_DONE FIELD32(0x00000004) |
| #define INT_SOURCE_CSR_TX_ABORT_DONE FIELD32(0x00000010) |
| #define INT_SOURCE_CSR_AC0_DMA_DONE FIELD32(0x00010000) |
| #define INT_SOURCE_CSR_AC1_DMA_DONE FIELD32(0x00020000) |
| #define INT_SOURCE_CSR_AC2_DMA_DONE FIELD32(0x00040000) |
| #define INT_SOURCE_CSR_AC3_DMA_DONE FIELD32(0x00080000) |
| #define INT_SOURCE_CSR_MGMT_DMA_DONE FIELD32(0x00100000) |
| #define INT_SOURCE_CSR_HCCA_DMA_DONE FIELD32(0x00200000) |
| |
| /* |
| * INT_MASK_CSR: Interrupt MASK register. 1: the interrupt is mask OFF. |
| * MITIGATION_PERIOD: Interrupt mitigation in unit of 32 PCI clock. |
| */ |
| #define INT_MASK_CSR 0x346c |
| #define INT_MASK_CSR_TXDONE FIELD32(0x00000001) |
| #define INT_MASK_CSR_RXDONE FIELD32(0x00000002) |
| #define INT_MASK_CSR_BEACON_DONE FIELD32(0x00000004) |
| #define INT_MASK_CSR_TX_ABORT_DONE FIELD32(0x00000010) |
| #define INT_MASK_CSR_ENABLE_MITIGATION FIELD32(0x00000080) |
| #define INT_MASK_CSR_MITIGATION_PERIOD FIELD32(0x0000ff00) |
| #define INT_MASK_CSR_AC0_DMA_DONE FIELD32(0x00010000) |
| #define INT_MASK_CSR_AC1_DMA_DONE FIELD32(0x00020000) |
| #define INT_MASK_CSR_AC2_DMA_DONE FIELD32(0x00040000) |
| #define INT_MASK_CSR_AC3_DMA_DONE FIELD32(0x00080000) |
| #define INT_MASK_CSR_MGMT_DMA_DONE FIELD32(0x00100000) |
| #define INT_MASK_CSR_HCCA_DMA_DONE FIELD32(0x00200000) |
| |
| /* |
| * E2PROM_CSR: EEPROM control register. |
| * RELOAD: Write 1 to reload eeprom content. |
| * TYPE_93C46: 1: 93c46, 0:93c66. |
| * LOAD_STATUS: 1:loading, 0:done. |
| */ |
| #define E2PROM_CSR 0x3470 |
| #define E2PROM_CSR_RELOAD FIELD32(0x00000001) |
| #define E2PROM_CSR_DATA_CLOCK FIELD32(0x00000002) |
| #define E2PROM_CSR_CHIP_SELECT FIELD32(0x00000004) |
| #define E2PROM_CSR_DATA_IN FIELD32(0x00000008) |
| #define E2PROM_CSR_DATA_OUT FIELD32(0x00000010) |
| #define E2PROM_CSR_TYPE_93C46 FIELD32(0x00000020) |
| #define E2PROM_CSR_LOAD_STATUS FIELD32(0x00000040) |
| |
| /* |
| * AC_TXOP_CSR0: AC_VO/AC_VI TXOP register. |
| * AC0_TX_OP: For AC_VO, in unit of 32us. |
| * AC1_TX_OP: For AC_VI, in unit of 32us. |
| */ |
| #define AC_TXOP_CSR0 0x3474 |
| #define AC_TXOP_CSR0_AC0_TX_OP FIELD32(0x0000ffff) |
| #define AC_TXOP_CSR0_AC1_TX_OP FIELD32(0xffff0000) |
| |
| /* |
| * AC_TXOP_CSR1: AC_BE/AC_BK TXOP register. |
| * AC2_TX_OP: For AC_BE, in unit of 32us. |
| * AC3_TX_OP: For AC_BK, in unit of 32us. |
| */ |
| #define AC_TXOP_CSR1 0x3478 |
| #define AC_TXOP_CSR1_AC2_TX_OP FIELD32(0x0000ffff) |
| #define AC_TXOP_CSR1_AC3_TX_OP FIELD32(0xffff0000) |
| |
| /* |
| * DMA_STATUS_CSR |
| */ |
| #define DMA_STATUS_CSR 0x3480 |
| |
| /* |
| * TEST_MODE_CSR |
| */ |
| #define TEST_MODE_CSR 0x3484 |
| |
| /* |
| * UART0_TX_CSR |
| */ |
| #define UART0_TX_CSR 0x3488 |
| |
| /* |
| * UART0_RX_CSR |
| */ |
| #define UART0_RX_CSR 0x348c |
| |
| /* |
| * UART0_FRAME_CSR |
| */ |
| #define UART0_FRAME_CSR 0x3490 |
| |
| /* |
| * UART0_BUFFER_CSR |
| */ |
| #define UART0_BUFFER_CSR 0x3494 |
| |
| /* |
| * IO_CNTL_CSR |
| * RF_PS: Set RF interface value to power save |
| */ |
| #define IO_CNTL_CSR 0x3498 |
| #define IO_CNTL_CSR_RF_PS FIELD32(0x00000004) |
| |
| /* |
| * UART_INT_SOURCE_CSR |
| */ |
| #define UART_INT_SOURCE_CSR 0x34a8 |
| |
| /* |
| * UART_INT_MASK_CSR |
| */ |
| #define UART_INT_MASK_CSR 0x34ac |
| |
| /* |
| * PBF_QUEUE_CSR |
| */ |
| #define PBF_QUEUE_CSR 0x34b0 |
| |
| /* |
| * Firmware DMA registers. |
| * Firmware DMA registers are dedicated for MCU usage |
| * and should not be touched by host driver. |
| * Therefore we skip the definition of these registers. |
| */ |
| #define FW_TX_BASE_CSR 0x34c0 |
| #define FW_TX_START_CSR 0x34c4 |
| #define FW_TX_LAST_CSR 0x34c8 |
| #define FW_MODE_CNTL_CSR 0x34cc |
| #define FW_TXPTR_CSR 0x34d0 |
| |
| /* |
| * 8051 firmware image. |
| */ |
| #define FIRMWARE_RT2561 "rt2561.bin" |
| #define FIRMWARE_RT2561s "rt2561s.bin" |
| #define FIRMWARE_RT2661 "rt2661.bin" |
| #define FIRMWARE_IMAGE_BASE 0x4000 |
| |
| /* |
| * BBP registers. |
| * The wordsize of the BBP is 8 bits. |
| */ |
| |
| /* |
| * R2 |
| */ |
| #define BBP_R2_BG_MODE FIELD8(0x20) |
| |
| /* |
| * R3 |
| */ |
| #define BBP_R3_SMART_MODE FIELD8(0x01) |
| |
| /* |
| * R4: RX antenna control |
| * FRAME_END: 1 - DPDT, 0 - SPDT (Only valid for 802.11G, RF2527 & RF2529) |
| */ |
| |
| /* |
| * ANTENNA_CONTROL semantics (guessed): |
| * 0x1: Software controlled antenna switching (fixed or SW diversity) |
| * 0x2: Hardware diversity. |
| */ |
| #define BBP_R4_RX_ANTENNA_CONTROL FIELD8(0x03) |
| #define BBP_R4_RX_FRAME_END FIELD8(0x20) |
| |
| /* |
| * R77 |
| */ |
| #define BBP_R77_RX_ANTENNA FIELD8(0x03) |
| |
| /* |
| * RF registers |
| */ |
| |
| /* |
| * RF 3 |
| */ |
| #define RF3_TXPOWER FIELD32(0x00003e00) |
| |
| /* |
| * RF 4 |
| */ |
| #define RF4_FREQ_OFFSET FIELD32(0x0003f000) |
| |
| /* |
| * EEPROM content. |
| * The wordsize of the EEPROM is 16 bits. |
| */ |
| |
| /* |
| * HW MAC address. |
| */ |
| #define EEPROM_MAC_ADDR_0 0x0002 |
| #define EEPROM_MAC_ADDR_BYTE0 FIELD16(0x00ff) |
| #define EEPROM_MAC_ADDR_BYTE1 FIELD16(0xff00) |
| #define EEPROM_MAC_ADDR1 0x0003 |
| #define EEPROM_MAC_ADDR_BYTE2 FIELD16(0x00ff) |
| #define EEPROM_MAC_ADDR_BYTE3 FIELD16(0xff00) |
| #define EEPROM_MAC_ADDR_2 0x0004 |
| #define EEPROM_MAC_ADDR_BYTE4 FIELD16(0x00ff) |
| #define EEPROM_MAC_ADDR_BYTE5 FIELD16(0xff00) |
| |
| /* |
| * EEPROM antenna. |
| * ANTENNA_NUM: Number of antenna's. |
| * TX_DEFAULT: Default antenna 0: diversity, 1: A, 2: B. |
| * RX_DEFAULT: Default antenna 0: diversity, 1: A, 2: B. |
| * FRAME_TYPE: 0: DPDT , 1: SPDT , noted this bit is valid for g only. |
| * DYN_TXAGC: Dynamic TX AGC control. |
| * HARDWARE_RADIO: 1: Hardware controlled radio. Read GPIO0. |
| * RF_TYPE: Rf_type of this adapter. |
| */ |
| #define EEPROM_ANTENNA 0x0010 |
| #define EEPROM_ANTENNA_NUM FIELD16(0x0003) |
| #define EEPROM_ANTENNA_TX_DEFAULT FIELD16(0x000c) |
| #define EEPROM_ANTENNA_RX_DEFAULT FIELD16(0x0030) |
| #define EEPROM_ANTENNA_FRAME_TYPE FIELD16(0x0040) |
| #define EEPROM_ANTENNA_DYN_TXAGC FIELD16(0x0200) |
| #define EEPROM_ANTENNA_HARDWARE_RADIO FIELD16(0x0400) |
| #define EEPROM_ANTENNA_RF_TYPE FIELD16(0xf800) |
| |
| /* |
| * EEPROM NIC config. |
| * ENABLE_DIVERSITY: 1:enable, 0:disable. |
| * EXTERNAL_LNA_BG: External LNA enable for 2.4G. |
| * CARDBUS_ACCEL: 0:enable, 1:disable. |
| * EXTERNAL_LNA_A: External LNA enable for 5G. |
| */ |
| #define EEPROM_NIC 0x0011 |
| #define EEPROM_NIC_ENABLE_DIVERSITY FIELD16(0x0001) |
| #define EEPROM_NIC_TX_DIVERSITY FIELD16(0x0002) |
| #define EEPROM_NIC_RX_FIXED FIELD16(0x0004) |
| #define EEPROM_NIC_TX_FIXED FIELD16(0x0008) |
| #define EEPROM_NIC_EXTERNAL_LNA_BG FIELD16(0x0010) |
| #define EEPROM_NIC_CARDBUS_ACCEL FIELD16(0x0020) |
| #define EEPROM_NIC_EXTERNAL_LNA_A FIELD16(0x0040) |
| |
| /* |
| * EEPROM geography. |
| * GEO_A: Default geographical setting for 5GHz band |
| * GEO: Default geographical setting. |
| */ |
| #define EEPROM_GEOGRAPHY 0x0012 |
| #define EEPROM_GEOGRAPHY_GEO_A FIELD16(0x00ff) |
| #define EEPROM_GEOGRAPHY_GEO FIELD16(0xff00) |
| |
| /* |
| * EEPROM BBP. |
| */ |
| #define EEPROM_BBP_START 0x0013 |
| #define EEPROM_BBP_SIZE 16 |
| #define EEPROM_BBP_VALUE FIELD16(0x00ff) |
| #define EEPROM_BBP_REG_ID FIELD16(0xff00) |
| |
| /* |
| * EEPROM TXPOWER 802.11G |
| */ |
| #define EEPROM_TXPOWER_G_START 0x0023 |
| #define EEPROM_TXPOWER_G_SIZE 7 |
| #define EEPROM_TXPOWER_G_1 FIELD16(0x00ff) |
| #define EEPROM_TXPOWER_G_2 FIELD16(0xff00) |
| |
| /* |
| * EEPROM Frequency |
| */ |
| #define EEPROM_FREQ 0x002f |
| #define EEPROM_FREQ_OFFSET FIELD16(0x00ff) |
| #define EEPROM_FREQ_SEQ_MASK FIELD16(0xff00) |
| #define EEPROM_FREQ_SEQ FIELD16(0x0300) |
| |
| /* |
| * EEPROM LED. |
| * POLARITY_RDY_G: Polarity RDY_G setting. |
| * POLARITY_RDY_A: Polarity RDY_A setting. |
| * POLARITY_ACT: Polarity ACT setting. |
| * POLARITY_GPIO_0: Polarity GPIO0 setting. |
| * POLARITY_GPIO_1: Polarity GPIO1 setting. |
| * POLARITY_GPIO_2: Polarity GPIO2 setting. |
| * POLARITY_GPIO_3: Polarity GPIO3 setting. |
| * POLARITY_GPIO_4: Polarity GPIO4 setting. |
| * LED_MODE: Led mode. |
| */ |
| #define EEPROM_LED 0x0030 |
| #define EEPROM_LED_POLARITY_RDY_G FIELD16(0x0001) |
| #define EEPROM_LED_POLARITY_RDY_A FIELD16(0x0002) |
| #define EEPROM_LED_POLARITY_ACT FIELD16(0x0004) |
| #define EEPROM_LED_POLARITY_GPIO_0 FIELD16(0x0008) |
| #define EEPROM_LED_POLARITY_GPIO_1 FIELD16(0x0010) |
| #define EEPROM_LED_POLARITY_GPIO_2 FIELD16(0x0020) |
| #define EEPROM_LED_POLARITY_GPIO_3 FIELD16(0x0040) |
| #define EEPROM_LED_POLARITY_GPIO_4 FIELD16(0x0080) |
| #define EEPROM_LED_LED_MODE FIELD16(0x1f00) |
| |
| /* |
| * EEPROM TXPOWER 802.11A |
| */ |
| #define EEPROM_TXPOWER_A_START 0x0031 |
| #define EEPROM_TXPOWER_A_SIZE 12 |
| #define EEPROM_TXPOWER_A_1 FIELD16(0x00ff) |
| #define EEPROM_TXPOWER_A_2 FIELD16(0xff00) |
| |
| /* |
| * EEPROM RSSI offset 802.11BG |
| */ |
| #define EEPROM_RSSI_OFFSET_BG 0x004d |
| #define EEPROM_RSSI_OFFSET_BG_1 FIELD16(0x00ff) |
| #define EEPROM_RSSI_OFFSET_BG_2 FIELD16(0xff00) |
| |
| /* |
| * EEPROM RSSI offset 802.11A |
| */ |
| #define EEPROM_RSSI_OFFSET_A 0x004e |
| #define EEPROM_RSSI_OFFSET_A_1 FIELD16(0x00ff) |
| #define EEPROM_RSSI_OFFSET_A_2 FIELD16(0xff00) |
| |
| /* |
| * MCU mailbox commands. |
| */ |
| #define MCU_SLEEP 0x30 |
| #define MCU_WAKEUP 0x31 |
| #define MCU_LED 0x50 |
| #define MCU_LED_STRENGTH 0x52 |
| |
| /* |
| * DMA descriptor defines. |
| */ |
| #define TXD_DESC_SIZE ( 16 * sizeof(__le32) ) |
| #define TXINFO_SIZE ( 6 * sizeof(__le32) ) |
| #define RXD_DESC_SIZE ( 16 * sizeof(__le32) ) |
| |
| /* |
| * TX descriptor format for TX, PRIO and Beacon Ring. |
| */ |
| |
| /* |
| * Word0 |
| * TKIP_MIC: ASIC appends TKIP MIC if TKIP is used. |
| * KEY_TABLE: Use per-client pairwise KEY table. |
| * KEY_INDEX: |
| * Key index (0~31) to the pairwise KEY table. |
| * 0~3 to shared KEY table 0 (BSS0). |
| * 4~7 to shared KEY table 1 (BSS1). |
| * 8~11 to shared KEY table 2 (BSS2). |
| * 12~15 to shared KEY table 3 (BSS3). |
| * BURST: Next frame belongs to same "burst" event. |
| */ |
| #define TXD_W0_OWNER_NIC FIELD32(0x00000001) |
| #define TXD_W0_VALID FIELD32(0x00000002) |
| #define TXD_W0_MORE_FRAG FIELD32(0x00000004) |
| #define TXD_W0_ACK FIELD32(0x00000008) |
| #define TXD_W0_TIMESTAMP FIELD32(0x00000010) |
| #define TXD_W0_OFDM FIELD32(0x00000020) |
| #define TXD_W0_IFS FIELD32(0x00000040) |
| #define TXD_W0_RETRY_MODE FIELD32(0x00000080) |
| #define TXD_W0_TKIP_MIC FIELD32(0x00000100) |
| #define TXD_W0_KEY_TABLE FIELD32(0x00000200) |
| #define TXD_W0_KEY_INDEX FIELD32(0x0000fc00) |
| #define TXD_W0_DATABYTE_COUNT FIELD32(0x0fff0000) |
| #define TXD_W0_BURST FIELD32(0x10000000) |
| #define TXD_W0_CIPHER_ALG FIELD32(0xe0000000) |
| |
| /* |
| * Word1 |
| * HOST_Q_ID: EDCA/HCCA queue ID. |
| * HW_SEQUENCE: MAC overwrites the frame sequence number. |
| * BUFFER_COUNT: Number of buffers in this TXD. |
| */ |
| #define TXD_W1_HOST_Q_ID FIELD32(0x0000000f) |
| #define TXD_W1_AIFSN FIELD32(0x000000f0) |
| #define TXD_W1_CWMIN FIELD32(0x00000f00) |
| #define TXD_W1_CWMAX FIELD32(0x0000f000) |
| #define TXD_W1_IV_OFFSET FIELD32(0x003f0000) |
| #define TXD_W1_PIGGY_BACK FIELD32(0x01000000) |
| #define TXD_W1_HW_SEQUENCE FIELD32(0x10000000) |
| #define TXD_W1_BUFFER_COUNT FIELD32(0xe0000000) |
| |
| /* |
| * Word2: PLCP information |
| */ |
| #define TXD_W2_PLCP_SIGNAL FIELD32(0x000000ff) |
| #define TXD_W2_PLCP_SERVICE FIELD32(0x0000ff00) |
| #define TXD_W2_PLCP_LENGTH_LOW FIELD32(0x00ff0000) |
| #define TXD_W2_PLCP_LENGTH_HIGH FIELD32(0xff000000) |
| |
| /* |
| * Word3 |
| */ |
| #define TXD_W3_IV FIELD32(0xffffffff) |
| |
| /* |
| * Word4 |
| */ |
| #define TXD_W4_EIV FIELD32(0xffffffff) |
| |
| /* |
| * Word5 |
| * FRAME_OFFSET: Frame start offset inside ASIC TXFIFO (after TXINFO field). |
| * TXD_W5_PID_SUBTYPE: Driver assigned packet ID index for txdone handler. |
| * TXD_W5_PID_TYPE: Driver assigned packet ID type for txdone handler. |
| * WAITING_DMA_DONE_INT: TXD been filled with data |
| * and waiting for TxDoneISR housekeeping. |
| */ |
| #define TXD_W5_FRAME_OFFSET FIELD32(0x000000ff) |
| #define TXD_W5_PID_SUBTYPE FIELD32(0x00001f00) |
| #define TXD_W5_PID_TYPE FIELD32(0x0000e000) |
| #define TXD_W5_TX_POWER FIELD32(0x00ff0000) |
| #define TXD_W5_WAITING_DMA_DONE_INT FIELD32(0x01000000) |
| |
| /* |
| * the above 24-byte is called TXINFO and will be DMAed to MAC block |
| * through TXFIFO. MAC block use this TXINFO to control the transmission |
| * behavior of this frame. |
| * The following fields are not used by MAC block. |
| * They are used by DMA block and HOST driver only. |
| * Once a frame has been DMA to ASIC, all the following fields are useless |
| * to ASIC. |
| */ |
| |
| /* |
| * Word6-10: Buffer physical address |
| */ |
| #define TXD_W6_BUFFER_PHYSICAL_ADDRESS FIELD32(0xffffffff) |
| #define TXD_W7_BUFFER_PHYSICAL_ADDRESS FIELD32(0xffffffff) |
| #define TXD_W8_BUFFER_PHYSICAL_ADDRESS FIELD32(0xffffffff) |
| #define TXD_W9_BUFFER_PHYSICAL_ADDRESS FIELD32(0xffffffff) |
| #define TXD_W10_BUFFER_PHYSICAL_ADDRESS FIELD32(0xffffffff) |
| |
| /* |
| * Word11-13: Buffer length |
| */ |
| #define TXD_W11_BUFFER_LENGTH0 FIELD32(0x00000fff) |
| #define TXD_W11_BUFFER_LENGTH1 FIELD32(0x0fff0000) |
| #define TXD_W12_BUFFER_LENGTH2 FIELD32(0x00000fff) |
| #define TXD_W12_BUFFER_LENGTH3 FIELD32(0x0fff0000) |
| #define TXD_W13_BUFFER_LENGTH4 FIELD32(0x00000fff) |
| |
| /* |
| * Word14 |
| */ |
| #define TXD_W14_SK_BUFFER FIELD32(0xffffffff) |
| |
| /* |
| * Word15 |
| */ |
| #define TXD_W15_NEXT_SK_BUFFER FIELD32(0xffffffff) |
| |
| /* |
| * RX descriptor format for RX Ring. |
| */ |
| |
| /* |
| * Word0 |
| * CIPHER_ERROR: 1:ICV error, 2:MIC error, 3:invalid key. |
| * KEY_INDEX: Decryption key actually used. |
| */ |
| #define RXD_W0_OWNER_NIC FIELD32(0x00000001) |
| #define RXD_W0_DROP FIELD32(0x00000002) |
| #define RXD_W0_UNICAST_TO_ME FIELD32(0x00000004) |
| #define RXD_W0_MULTICAST FIELD32(0x00000008) |
| #define RXD_W0_BROADCAST FIELD32(0x00000010) |
| #define RXD_W0_MY_BSS FIELD32(0x00000020) |
| #define RXD_W0_CRC_ERROR FIELD32(0x00000040) |
| #define RXD_W0_OFDM FIELD32(0x00000080) |
| #define RXD_W0_CIPHER_ERROR FIELD32(0x00000300) |
| #define RXD_W0_KEY_INDEX FIELD32(0x0000fc00) |
| #define RXD_W0_DATABYTE_COUNT FIELD32(0x0fff0000) |
| #define RXD_W0_CIPHER_ALG FIELD32(0xe0000000) |
| |
| /* |
| * Word1 |
| * SIGNAL: RX raw data rate reported by BBP. |
| */ |
| #define RXD_W1_SIGNAL FIELD32(0x000000ff) |
| #define RXD_W1_RSSI_AGC FIELD32(0x00001f00) |
| #define RXD_W1_RSSI_LNA FIELD32(0x00006000) |
| #define RXD_W1_FRAME_OFFSET FIELD32(0x7f000000) |
| |
| /* |
| * Word2 |
| * IV: Received IV of originally encrypted. |
| */ |
| #define RXD_W2_IV FIELD32(0xffffffff) |
| |
| /* |
| * Word3 |
| * EIV: Received EIV of originally encrypted. |
| */ |
| #define RXD_W3_EIV FIELD32(0xffffffff) |
| |
| /* |
| * Word4 |
| * ICV: Received ICV of originally encrypted. |
| * NOTE: This is a guess, the official definition is "reserved" |
| */ |
| #define RXD_W4_ICV FIELD32(0xffffffff) |
| |
| /* |
| * the above 20-byte is called RXINFO and will be DMAed to MAC RX block |
| * and passed to the HOST driver. |
| * The following fields are for DMA block and HOST usage only. |
| * Can't be touched by ASIC MAC block. |
| */ |
| |
| /* |
| * Word5 |
| */ |
| #define RXD_W5_BUFFER_PHYSICAL_ADDRESS FIELD32(0xffffffff) |
| |
| /* |
| * Word6-15: Reserved |
| */ |
| #define RXD_W6_RESERVED FIELD32(0xffffffff) |
| #define RXD_W7_RESERVED FIELD32(0xffffffff) |
| #define RXD_W8_RESERVED FIELD32(0xffffffff) |
| #define RXD_W9_RESERVED FIELD32(0xffffffff) |
| #define RXD_W10_RESERVED FIELD32(0xffffffff) |
| #define RXD_W11_RESERVED FIELD32(0xffffffff) |
| #define RXD_W12_RESERVED FIELD32(0xffffffff) |
| #define RXD_W13_RESERVED FIELD32(0xffffffff) |
| #define RXD_W14_RESERVED FIELD32(0xffffffff) |
| #define RXD_W15_RESERVED FIELD32(0xffffffff) |
| |
| /* |
| * Macros for converting txpower from EEPROM to mac80211 value |
| * and from mac80211 value to register value. |
| */ |
| #define MIN_TXPOWER 0 |
| #define MAX_TXPOWER 31 |
| #define DEFAULT_TXPOWER 24 |
| |
| #define TXPOWER_FROM_DEV(__txpower) \ |
| (((u8)(__txpower)) > MAX_TXPOWER) ? DEFAULT_TXPOWER : (__txpower) |
| |
| #define TXPOWER_TO_DEV(__txpower) \ |
| clamp_t(char, __txpower, MIN_TXPOWER, MAX_TXPOWER) |
| |
| #endif /* RT61PCI_H */ |