ixgbe: add support for VF Transmit rate limit using iproute2
Implemented ixgbe_ndo_set_vf_bw function which is being used by iproute2
tool. In addition, updated ixgbe_ndo_get_vf_config function to show the
actual rate limit to the user.
The rate limitation can be configured only when the link is up and the
link speed is 10Gb.
The rate limit value can be 0 or ranged between 11 and actual link
speed measured in Mbps. A value of '0' disables the rate limit for
this specific VF.
iproute2 usage will be 'ip link set ethX vf Y rate Z'.
After the command is made, the rate will be changed instantly.
To view the current rate limit, use 'ip link show ethX'.
The rates will be zeroed only upon driver reload or a link speed change.
This feature is being supported by 82599 and X540 devices.
Signed-off-by: Lior Levy <lior.levy@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
diff --git a/drivers/net/ixgbe/ixgbe_sriov.c b/drivers/net/ixgbe/ixgbe_sriov.c
index 58c9b45..6e50d83 100644
--- a/drivers/net/ixgbe/ixgbe_sriov.c
+++ b/drivers/net/ixgbe/ixgbe_sriov.c
@@ -478,9 +478,90 @@
return err;
}
+static int ixgbe_link_mbps(int internal_link_speed)
+{
+ switch (internal_link_speed) {
+ case IXGBE_LINK_SPEED_100_FULL:
+ return 100;
+ case IXGBE_LINK_SPEED_1GB_FULL:
+ return 1000;
+ case IXGBE_LINK_SPEED_10GB_FULL:
+ return 10000;
+ default:
+ return 0;
+ }
+}
+
+static void ixgbe_set_vf_rate_limit(struct ixgbe_hw *hw, int vf, int tx_rate,
+ int link_speed)
+{
+ int rf_dec, rf_int;
+ u32 bcnrc_val;
+
+ if (tx_rate != 0) {
+ /* Calculate the rate factor values to set */
+ rf_int = link_speed / tx_rate;
+ rf_dec = (link_speed - (rf_int * tx_rate));
+ rf_dec = (rf_dec * (1<<IXGBE_RTTBCNRC_RF_INT_SHIFT)) / tx_rate;
+
+ bcnrc_val = IXGBE_RTTBCNRC_RS_ENA;
+ bcnrc_val |= ((rf_int<<IXGBE_RTTBCNRC_RF_INT_SHIFT) &
+ IXGBE_RTTBCNRC_RF_INT_MASK);
+ bcnrc_val |= (rf_dec & IXGBE_RTTBCNRC_RF_DEC_MASK);
+ } else {
+ bcnrc_val = 0;
+ }
+
+ IXGBE_WRITE_REG(hw, IXGBE_RTTDQSEL, 2*vf); /* vf Y uses queue 2*Y */
+ IXGBE_WRITE_REG(hw, IXGBE_RTTBCNRC, bcnrc_val);
+}
+
+void ixgbe_check_vf_rate_limit(struct ixgbe_adapter *adapter)
+{
+ int actual_link_speed, i;
+ bool reset_rate = false;
+
+ /* VF Tx rate limit was not set */
+ if (adapter->vf_rate_link_speed == 0)
+ return;
+
+ actual_link_speed = ixgbe_link_mbps(adapter->link_speed);
+ if (actual_link_speed != adapter->vf_rate_link_speed) {
+ reset_rate = true;
+ adapter->vf_rate_link_speed = 0;
+ dev_info(&adapter->pdev->dev,
+ "Link speed has been changed. VF Transmit rate "
+ "is disabled\n");
+ }
+
+ for (i = 0; i < adapter->num_vfs; i++) {
+ if (reset_rate)
+ adapter->vfinfo[i].tx_rate = 0;
+
+ ixgbe_set_vf_rate_limit(&adapter->hw, i,
+ adapter->vfinfo[i].tx_rate,
+ actual_link_speed);
+ }
+}
+
int ixgbe_ndo_set_vf_bw(struct net_device *netdev, int vf, int tx_rate)
{
- return -EOPNOTSUPP;
+ struct ixgbe_adapter *adapter = netdev_priv(netdev);
+ struct ixgbe_hw *hw = &adapter->hw;
+ int actual_link_speed;
+
+ actual_link_speed = ixgbe_link_mbps(adapter->link_speed);
+ if ((vf >= adapter->num_vfs) || (!adapter->link_up) ||
+ (tx_rate > actual_link_speed) || (actual_link_speed != 10000) ||
+ ((tx_rate != 0) && (tx_rate <= 10)))
+ /* rate limit cannot be set to 10Mb or less in 10Gb adapters */
+ return -EINVAL;
+
+ adapter->vf_rate_link_speed = actual_link_speed;
+ adapter->vfinfo[vf].tx_rate = (u16)tx_rate;
+ ixgbe_set_vf_rate_limit(hw, vf, tx_rate, actual_link_speed);
+
+ return 0;
}
int ixgbe_ndo_get_vf_config(struct net_device *netdev,
@@ -491,7 +572,7 @@
return -EINVAL;
ivi->vf = vf;
memcpy(&ivi->mac, adapter->vfinfo[vf].vf_mac_addresses, ETH_ALEN);
- ivi->tx_rate = 0;
+ ivi->tx_rate = adapter->vfinfo[vf].tx_rate;
ivi->vlan = adapter->vfinfo[vf].pf_vlan;
ivi->qos = adapter->vfinfo[vf].pf_qos;
return 0;