| Laurent Pinchart | 7ef077a | 2015-01-21 00:56:02 +0200 | [diff] [blame] | 1 | config USB_ISP1760 |
| 2 | tristate "NXP ISP 1760/1761 support" |
| Laurent Pinchart | 100832a | 2015-01-21 00:56:03 +0200 | [diff] [blame] | 3 | depends on USB || USB_GADGET |
| Laurent Pinchart | 7ef077a | 2015-01-21 00:56:02 +0200 | [diff] [blame] | 4 | help |
| 5 | Say Y or M here if your system as an ISP1760 USB host controller |
| 6 | or an ISP1761 USB dual-role controller. |
| 7 | |
| 8 | This driver does not support isochronous transfers or OTG. |
| 9 | This USB controller is usually attached to a non-DMA-Master |
| 10 | capable bus. NXP's eval kit brings this chip on PCI card |
| 11 | where the chip itself is behind a PLB to simulate such |
| 12 | a bus. |
| 13 | |
| 14 | To compile this driver as a module, choose M here: the |
| 15 | module will be called isp1760. |
| 16 | |
| Laurent Pinchart | 100832a | 2015-01-21 00:56:03 +0200 | [diff] [blame] | 17 | config USB_ISP1760_HCD |
| 18 | bool |
| 19 | |
| Laurent Pinchart | 7ef077a | 2015-01-21 00:56:02 +0200 | [diff] [blame] | 20 | config USB_ISP1761_UDC |
| Laurent Pinchart | 100832a | 2015-01-21 00:56:03 +0200 | [diff] [blame] | 21 | bool |
| 22 | |
| 23 | if USB_ISP1760 |
| 24 | |
| 25 | choice |
| 26 | bool "ISP1760 Mode Selection" |
| 27 | default USB_ISP1760_DUAL_ROLE if (USB && USB_GADGET) |
| 28 | default USB_ISP1760_HOST_ROLE if (USB && !USB_GADGET) |
| 29 | default USB_ISP1760_GADGET_ROLE if (!USB && USB_GADGET) |
| 30 | |
| 31 | config USB_ISP1760_HOST_ROLE |
| 32 | bool "Host only mode" |
| 33 | depends on USB=y || USB=USB_ISP1760 |
| 34 | select USB_ISP1760_HCD |
| Laurent Pinchart | 7ef077a | 2015-01-21 00:56:02 +0200 | [diff] [blame] | 35 | help |
| Laurent Pinchart | 100832a | 2015-01-21 00:56:03 +0200 | [diff] [blame] | 36 | Select this if you want to use the ISP1760 in host mode only. The |
| 37 | gadget function will be disabled. |
| 38 | |
| 39 | config USB_ISP1760_GADGET_ROLE |
| 40 | bool "Gadget only mode" |
| 41 | depends on USB_GADGET=y || USB_GADGET=USB_ISP1760 |
| 42 | select USB_ISP1761_UDC |
| 43 | help |
| 44 | Select this if you want to use the ISP1760 in peripheral mode only. |
| 45 | The host function will be disabled. |
| 46 | |
| 47 | config USB_ISP1760_DUAL_ROLE |
| 48 | bool "Dual Role mode" |
| 49 | depends on USB=y || USB=USB_ISP1760 |
| 50 | depends on USB_GADGET=y || USB_GADGET=USB_ISP1760 |
| 51 | select USB_ISP1760_HCD |
| 52 | select USB_ISP1761_UDC |
| 53 | help |
| 54 | Select this if you want to use the ISP1760 in both host and |
| 55 | peripheral modes. |
| 56 | |
| 57 | endchoice |
| 58 | |
| 59 | endif |