arch/cris/Kconfig

#
# For a description of the syntax of this configuration file,
# see the Configure script.
#

mainmenu "Linux/CRIS Kernel Configuration"

config MMU
	bool
	default y

config ZONE_DMA
	bool
	default y

config NO_DMA
	bool
	default y

config RWSEM_GENERIC_SPINLOCK
	bool
	default y

config RWSEM_XCHGADD_ALGORITHM
	bool

config ARCH_HAS_ILOG2_U32
	bool
	default n

config ARCH_HAS_ILOG2_U64
	bool
	default n

config GENERIC_FIND_NEXT_BIT
	bool
	default y

config GENERIC_HWEIGHT
	bool
	default y

config GENERIC_CALIBRATE_DELAY
	bool
	default y

config IRQ_PER_CPU
	bool
	default y

config NO_IOPORT
	def_bool y

config CRIS
	bool
	default y

source "init/Kconfig"

menu "General setup"

source "fs/Kconfig.binfmt"

config GENERIC_HARDIRQS
	bool
	default y

config ETRAX_CMDLINE
	string "Kernel command line"
	default "root=/dev/mtdblock3"
	help
	  Pass additional commands to the kernel.

config ETRAX_WATCHDOG
	bool "Enable ETRAX watchdog"
	help
	  Enable the built-in watchdog timer support on ETRAX based embedded
	  network computers.

config ETRAX_WATCHDOG_NICE_DOGGY
	bool "Disable watchdog during Oops printouts"
	depends on ETRAX_WATCHDOG
	help
	  By enabling this you make sure that the watchdog does not bite while
	  printing oopses. Recommended for development systems but not for
	  production releases.

config ETRAX_FAST_TIMER
       bool "Enable ETRAX fast timer API"
       help
         This options enables the API to a fast timer implementation using
	 timer1 to get sub jiffie resolution timers (primarily one-shot
	 timers).
	 This is needed if CONFIG_ETRAX_SERIAL_FAST_TIMER is enabled.

config PREEMPT
	bool "Preemptible Kernel"
	help
	  This option reduces the latency of the kernel when reacting to
	  real-time or interactive events by allowing a low priority process to
	  be preempted even if it is in kernel mode executing a system call.
	  This allows applications to run more reliably even when the system is
	  under load.

	  Say Y here if you are building a kernel for a desktop, embedded
	  or real-time system.  Say N if you are unsure.

source mm/Kconfig

endmenu

menu "Hardware setup"

choice
	prompt "Processor type"
	default ETRAX100LX

config ETRAX100LX
	bool "ETRAX-100LX-v1"
	help
	  Support version 1 of the ETRAX 100LX.

config ETRAX100LX_V2
	bool "ETRAX-100LX-v2"
	help
	  Support version 2 of the ETRAX 100LX.

config SVINTO_SIM
	bool "ETRAX-100LX-for-xsim-simulator"
	help
	  Support the xsim ETRAX Simulator.

endchoice

config ETRAX_ARCH_V10
       bool
       default y if ETRAX100LX || ETRAX100LX_V2
       default n if !(ETRAX100LX || ETRAX100LX_V2)

config ETRAX_DRAM_SIZE
	int "DRAM size (dec, in MB)"
	default "8"
	help
	  Size of DRAM (decimal in MB) typically 2, 8 or 16.

config ETRAX_FLASH_BUSWIDTH
	int "Buswidth of flash in bytes"
	default "2"
	help
	  Width in bytes of the Flash bus (1, 2 or 4). Is usually 2.

source arch/cris/arch-v10/Kconfig

endmenu

source "net/Kconfig"

# bring in ETRAX built-in drivers
menu "Drivers for built-in interfaces"
# arch/cris/arch is a symlink to correct arch (arch-v10 or arch-v32)
source arch/cris/arch/drivers/Kconfig

endmenu

source "drivers/base/Kconfig"

# standard linux drivers
source "drivers/mtd/Kconfig"

source "drivers/parport/Kconfig"

source "drivers/pnp/Kconfig"

source "drivers/block/Kconfig"

source "drivers/md/Kconfig"

source "drivers/ide/Kconfig"

source "drivers/scsi/Kconfig"

source "drivers/ieee1394/Kconfig"

source "drivers/message/i2o/Kconfig"

source "drivers/net/Kconfig"

source "drivers/isdn/Kconfig"

source "drivers/telephony/Kconfig"

source "drivers/i2c/Kconfig"

source "drivers/rtc/Kconfig"

#
# input before char - char/joystick depends on it. As does USB.
#
source "drivers/input/Kconfig"

source "drivers/char/Kconfig"

#source drivers/misc/Config.in
source "drivers/media/Kconfig"

source "fs/Kconfig"

source "sound/Kconfig"

source "drivers/pcmcia/Kconfig"

source "drivers/pci/Kconfig"

source "drivers/usb/Kconfig"

source "kernel/Kconfig.instrumentation"

source "arch/cris/Kconfig.debug"

source "security/Kconfig"

source "crypto/Kconfig"

source "lib/Kconfig"