| Andrew Lunn | e2eaa33 | 2014-02-15 13:59:53 +0100 | [diff] [blame] | 1 | /* |
| 2 | * Marvell RD88F6181 Common Board descrition |
| 3 | * |
| 4 | * Andrew Lunn <andrew@lunn.ch> |
| 5 | * |
| 6 | * This file is licensed under the terms of the GNU General Public |
| 7 | * License version 2. This program is licensed "as is" without any |
| 8 | * warranty of any kind, whether express or implied. |
| 9 | * |
| 10 | * This file contains the definitions that are common between the two |
| 11 | * variants of the Marvell Kirkwood Development Board. |
| 12 | */ |
| 13 | |
| 14 | #include "kirkwood.dtsi" |
| 15 | #include "kirkwood-6281.dtsi" |
| 16 | |
| 17 | / { |
| 18 | memory { |
| 19 | device_type = "memory"; |
| 20 | reg = <0x00000000 0x20000000>; |
| 21 | }; |
| 22 | |
| 23 | chosen { |
| 24 | bootargs = "console=ttyS0,115200n8"; |
| 25 | }; |
| 26 | |
| 27 | mbus { |
| 28 | pcie-controller { |
| 29 | status = "okay"; |
| 30 | |
| 31 | pcie@1,0 { |
| 32 | status = "okay"; |
| 33 | }; |
| 34 | }; |
| 35 | }; |
| 36 | |
| 37 | ocp@f1000000 { |
| 38 | pinctrl: pinctrl@10000 { |
| 39 | pinctrl-0 = <&pmx_sdio_cd>; |
| 40 | pinctrl-names = "default"; |
| 41 | |
| 42 | pmx_sdio_cd: pmx-sdio-cd { |
| 43 | marvell,pins = "mpp28"; |
| 44 | marvell,function = "gpio"; |
| 45 | }; |
| 46 | }; |
| 47 | |
| 48 | serial@12000 { |
| 49 | status = "okay"; |
| 50 | |
| 51 | }; |
| 52 | |
| 53 | sata@80000 { |
| 54 | status = "okay"; |
| 55 | nr-ports = <2>; |
| 56 | }; |
| 57 | mvsdio@90000 { |
| 58 | pinctrl-0 = <&pmx_sdio &pmx_sdio_cd>; |
| 59 | pinctrl-names = "default"; |
| 60 | status = "okay"; |
| 61 | cd-gpios = <&gpio0 28 GPIO_ACTIVE_HIGH>; |
| 62 | /* No WP GPIO */ |
| 63 | }; |
| 64 | }; |
| 65 | |
| 66 | dsa@0 { |
| 67 | compatible = "marvell,dsa"; |
| 68 | #address-cells = <2>; |
| 69 | #size-cells = <0>; |
| 70 | |
| 71 | dsa,ethernet = <ð0>; |
| 72 | dsa,mii-bus = <ðphy1>; |
| 73 | |
| 74 | switch@0 { |
| 75 | #address-cells = <1>; |
| 76 | #size-cells = <0>; |
| 77 | |
| 78 | port@0 { |
| 79 | reg = <0>; |
| 80 | label = "lan1"; |
| 81 | }; |
| 82 | |
| 83 | port@1 { |
| 84 | reg = <1>; |
| 85 | label = "lan2"; |
| 86 | }; |
| 87 | |
| 88 | port@2 { |
| 89 | reg = <2>; |
| 90 | label = "lan3"; |
| 91 | }; |
| 92 | |
| 93 | port@3 { |
| 94 | reg = <3>; |
| 95 | label = "lan4"; |
| 96 | }; |
| 97 | |
| 98 | port@5 { |
| 99 | reg = <5>; |
| 100 | label = "cpu"; |
| 101 | }; |
| 102 | }; |
| 103 | }; |
| 104 | }; |
| 105 | |
| 106 | &nand { |
| 107 | status = "okay"; |
| 108 | |
| 109 | partition@0 { |
| 110 | label = "u-boot"; |
| 111 | reg = <0x0000000 0x100000>; |
| 112 | read-only; |
| 113 | }; |
| 114 | |
| 115 | partition@100000 { |
| 116 | label = "uImage"; |
| 117 | reg = <0x0100000 0x200000>; |
| 118 | }; |
| 119 | |
| 120 | partition@300000 { |
| 121 | label = "data"; |
| 122 | reg = <0x0300000 0x500000>; |
| 123 | }; |
| 124 | }; |
| 125 | |
| 126 | &mdio { |
| 127 | status = "okay"; |
| 128 | |
| 129 | ethphy0: ethernet-phy@0 { |
| 130 | reg = <0>; |
| 131 | }; |
| 132 | |
| 133 | ethphy1: ethernet-phy@ff { |
| 134 | reg = <0xff>; /* No PHY attached */ |
| 135 | speed = <1000>; |
| 136 | duple = <1>; |
| 137 | }; |
| 138 | }; |
| 139 | |
| 140 | ð0 { |
| 141 | status = "okay"; |
| 142 | ethernet0-port@0 { |
| 143 | phy-handle = <ðphy0>; |
| 144 | }; |
| 145 | }; |
| 146 | |
| 147 | ð1 { |
| 148 | status = "okay"; |
| 149 | ethernet1-port@0 { |
| 150 | phy-handle = <ðphy1>; |
| 151 | }; |
| 152 | }; |