| Sebastian Hesselbarth | 3707873 | 2013-08-12 20:46:54 +0200 | [diff] [blame] | 1 | /dts-v1/; |
| 2 | |
| 3 | #include "dove.dtsi" |
| 4 | |
| 5 | / { |
| 6 | model = "Globalscale D3Plug"; |
| 7 | compatible = "globalscale,d3plug", "marvell,dove"; |
| 8 | |
| 9 | memory { |
| 10 | device_type = "memory"; |
| 11 | reg = <0x00000000 0x40000000>; |
| 12 | }; |
| 13 | |
| 14 | chosen { |
| 15 | bootargs = "console=ttyS0,115200n8 earlyprintk root=/dev/mmcblk0p2 rw rootwait"; |
| 16 | }; |
| 17 | |
| 18 | leds { |
| 19 | compatible = "gpio-leds"; |
| 20 | pinctrl-0 = <&pmx_gpio_0 &pmx_gpio_1 &pmx_gpio_2>; |
| 21 | pinctrl-names = "default"; |
| 22 | |
| 23 | wlan-act { |
| 24 | label = "wlan-act"; |
| 25 | gpios = <&gpio0 0 1>; |
| 26 | }; |
| 27 | |
| 28 | wlan-ap { |
| 29 | label = "wlan-ap"; |
| 30 | gpios = <&gpio0 1 1>; |
| 31 | }; |
| 32 | |
| 33 | status { |
| 34 | label = "status"; |
| 35 | gpios = <&gpio0 2 1>; |
| 36 | }; |
| 37 | }; |
| 38 | |
| 39 | regulators { |
| 40 | compatible = "simple-bus"; |
| 41 | #address-cells = <1>; |
| 42 | #size-cells = <0>; |
| 43 | |
| 44 | usb_power: regulator@1 { |
| 45 | compatible = "regulator-fixed"; |
| 46 | reg = <1>; |
| 47 | regulator-name = "USB Power"; |
| 48 | regulator-min-microvolt = <5000000>; |
| 49 | regulator-max-microvolt = <5000000>; |
| 50 | enable-active-high; |
| 51 | regulator-always-on; |
| 52 | regulator-boot-on; |
| 53 | gpio = <&gpio0 8 0>; |
| 54 | pinctrl-0 = <&pmx_gpio_8>; |
| 55 | pinctrl-names = "default"; |
| 56 | }; |
| 57 | }; |
| 58 | }; |
| 59 | |
| 60 | &uart0 { status = "okay"; }; |
| 61 | &sata0 { status = "okay"; }; |
| 62 | &i2c0 { status = "okay"; }; |
| 63 | |
| 64 | /* Samsung M8G2F eMMC */ |
| 65 | &sdio0 { |
| 66 | status = "okay"; |
| 67 | non-removable; |
| 68 | bus-width = <4>; |
| 69 | }; |
| 70 | |
| 71 | /* Marvell SD8787 WLAN/BT */ |
| 72 | &sdio1 { |
| 73 | status = "okay"; |
| 74 | non-removable; |
| 75 | }; |
| 76 | |
| 77 | &spi0 { |
| 78 | status = "okay"; |
| 79 | |
| 80 | /* spi0.0: 2M Flash Macronix MX25L1605D */ |
| 81 | spi-flash@0 { |
| 82 | compatible = "st,m25l1605d"; |
| 83 | spi-max-frequency = <86000000>; |
| 84 | reg = <0>; |
| 85 | }; |
| 86 | }; |
| 87 | |
| 88 | &pcie { |
| 89 | status = "okay"; |
| 90 | /* Fresco Logic USB3.0 xHCI controller */ |
| 91 | pcie-port@0 { |
| 92 | status = "okay"; |
| 93 | reset-gpios = <&gpio0 26 1>; |
| 94 | reset-delay-us = <20000>; |
| 95 | pinctrl-0 = <&pmx_camera_gpio>; |
| 96 | pinctrl-names = "default"; |
| 97 | }; |
| 98 | /* Mini-PCIe slot */ |
| 99 | pcie-port@1 { |
| 100 | status = "okay"; |
| 101 | reset-gpios = <&gpio0 25 1>; |
| 102 | }; |
| 103 | }; |