| Eduard Hasenleithner | 5d7e7d4 | 2011-09-07 14:08:54 -0700 | [diff] [blame] | 1 | What: /sys/class/hidraw/hidraw*/device/speed |
| 2 | Date: April 2010 |
| 3 | Kernel Version: 2.6.35 |
| 4 | Contact: linux-bluetooth@vger.kernel.org |
| 5 | Description: |
| 6 | The /sys/class/hidraw/hidraw*/device/speed file controls |
| 7 | reporting speed of Wacom bluetooth tablet. Reading from |
| 8 | this file returns 1 if tablet reports in high speed mode |
| 9 | or 0 otherwise. Writing to this file one of these values |
| 10 | switches reporting speed. |
| 11 | |
| 12 | What: /sys/bus/usb/devices/<busnum>-<devnum>:<cfg>.<intf>/wacom_led/led |
| 13 | Date: August 2011 |
| 14 | Contact: linux-input@vger.kernel.org |
| 15 | Description: |
| 16 | Attribute group for control of the status LEDs and the OLED |
| 17 | displays found on the Wacom Intuos 4 M, L, and XL tablets. This |
| 18 | attribute group is not available for other Wacom tablets. |
| 19 | Therefore its presence implicitly signifies the presence of |
| 20 | said LEDs and OLED displays on the tablet device. |
| 21 | |
| 22 | What: /sys/bus/usb/devices/<busnum>-<devnum>:<cfg>.<intf>/wacom_led/status0_luminance |
| 23 | Date: August 2011 |
| 24 | Contact: linux-input@vger.kernel.org |
| 25 | Description: |
| 26 | Writing to this file sets the status LED luminance (0..127) |
| 27 | when the stylus does not touch the tablet surface, and no |
| Ping Cheng | f4fa9a6 | 2011-10-04 23:49:42 -0700 | [diff] [blame^] | 28 | button is pressed on the stylus. This luminance level is |
| 29 | normally lower than the level when a button is pressed. |
| Eduard Hasenleithner | 5d7e7d4 | 2011-09-07 14:08:54 -0700 | [diff] [blame] | 30 | |
| 31 | What: /sys/bus/usb/devices/<busnum>-<devnum>:<cfg>.<intf>/wacom_led/status1_luminance |
| 32 | Date: August 2011 |
| 33 | Contact: linux-input@vger.kernel.org |
| 34 | Description: |
| 35 | Writing to this file sets the status LED luminance (0..127) |
| 36 | when the stylus touches the tablet surface, or any button is |
| 37 | pressed on the stylus. |
| 38 | |
| 39 | What: /sys/bus/usb/devices/<busnum>-<devnum>:<cfg>.<intf>/wacom_led/status_led_select |
| 40 | Date: August 2011 |
| 41 | Contact: linux-input@vger.kernel.org |
| 42 | Description: |
| 43 | Writing to this file sets which one of the four status LEDs is |
| 44 | active (0..3). The other three LEDs are always inactive. By |
| 45 | means of specifying "-1" it is possible to set all status LEDs |
| 46 | to inactive. |
| 47 | |
| 48 | What: /sys/bus/usb/devices/<busnum>-<devnum>:<cfg>.<intf>/wacom_led/buttons_luminance |
| 49 | Date: August 2011 |
| 50 | Contact: linux-input@vger.kernel.org |
| 51 | Description: |
| 52 | Writing to this file sets the overall luminance level (0..15) |
| 53 | of all eight button OLED displays. |
| 54 | |
| 55 | What: /sys/bus/usb/devices/<busnum>-<devnum>:<cfg>.<intf>/wacom_led/button<n>_rawimg |
| 56 | Date: August 2011 |
| 57 | Contact: linux-input@vger.kernel.org |
| 58 | Description: |
| 59 | When writing a 1024 byte raw image in Wacom Intuos 4 |
| 60 | interleaving format to the file, the image shows up on Button N |
| 61 | of the device. The image is a 64x32 pixel 4-bit gray image. The |
| 62 | 1024 byte binary is split up into 16x 64 byte chunks. Each 64 |
| 63 | byte chunk encodes the image data for two consecutive lines on |
| 64 | the display. The low nibble of each byte contains the first |
| 65 | line, and the high nibble contains the second line. |