Sangwook Lee | 8b99312 | 2012-09-13 07:02:14 -0300 | [diff] [blame] | 1 | /* |
| 2 | * Driver for Samsung S5K4ECGX 1/4" 5Mp CMOS Image Sensor SoC |
| 3 | * with an Embedded Image Signal Processor. |
| 4 | * |
| 5 | * Copyright (C) 2012, Linaro, Sangwook Lee <sangwook.lee@linaro.org> |
| 6 | * Copyright (C) 2012, Insignal Co,. Ltd, Homin Lee <suapapa@insignal.co.kr> |
| 7 | * |
| 8 | * Based on s5k6aa and noon010pc30 driver |
| 9 | * Copyright (C) 2011, Samsung Electronics Co., Ltd. |
| 10 | * |
| 11 | * This program is free software; you can redistribute it and/or modify |
| 12 | * it under the terms of the GNU General Public License as published by |
| 13 | * the Free Software Foundation; either version 2 of the License, or |
| 14 | * (at your option) any later version. |
| 15 | */ |
| 16 | |
| 17 | #include <linux/clk.h> |
| 18 | #include <linux/crc32.h> |
| 19 | #include <linux/ctype.h> |
| 20 | #include <linux/delay.h> |
| 21 | #include <linux/firmware.h> |
| 22 | #include <linux/gpio.h> |
| 23 | #include <linux/i2c.h> |
| 24 | #include <linux/module.h> |
| 25 | #include <linux/regulator/consumer.h> |
| 26 | #include <linux/slab.h> |
| 27 | #include <asm/unaligned.h> |
| 28 | |
| 29 | #include <media/media-entity.h> |
| 30 | #include <media/s5k4ecgx.h> |
| 31 | #include <media/v4l2-ctrls.h> |
| 32 | #include <media/v4l2-device.h> |
| 33 | #include <media/v4l2-mediabus.h> |
| 34 | #include <media/v4l2-subdev.h> |
| 35 | |
| 36 | static int debug; |
| 37 | module_param(debug, int, 0644); |
| 38 | |
| 39 | #define S5K4ECGX_DRIVER_NAME "s5k4ecgx" |
| 40 | #define S5K4ECGX_FIRMWARE "s5k4ecgx.bin" |
| 41 | |
| 42 | /* Firmware revision information */ |
| 43 | #define REG_FW_REVISION 0x700001a6 |
| 44 | #define REG_FW_VERSION 0x700001a4 |
| 45 | #define S5K4ECGX_REVISION_1_1 0x11 |
| 46 | #define S5K4ECGX_FW_VERSION 0x4ec0 |
| 47 | |
| 48 | /* General purpose parameters */ |
| 49 | #define REG_USER_BRIGHTNESS 0x7000022c |
| 50 | #define REG_USER_CONTRAST 0x7000022e |
| 51 | #define REG_USER_SATURATION 0x70000230 |
| 52 | |
| 53 | #define REG_G_ENABLE_PREV 0x7000023e |
| 54 | #define REG_G_ENABLE_PREV_CHG 0x70000240 |
| 55 | #define REG_G_NEW_CFG_SYNC 0x7000024a |
| 56 | #define REG_G_PREV_IN_WIDTH 0x70000250 |
| 57 | #define REG_G_PREV_IN_HEIGHT 0x70000252 |
| 58 | #define REG_G_PREV_IN_XOFFS 0x70000254 |
| 59 | #define REG_G_PREV_IN_YOFFS 0x70000256 |
| 60 | #define REG_G_CAP_IN_WIDTH 0x70000258 |
| 61 | #define REG_G_CAP_IN_HEIGHT 0x7000025a |
| 62 | #define REG_G_CAP_IN_XOFFS 0x7000025c |
| 63 | #define REG_G_CAP_IN_YOFFS 0x7000025e |
| 64 | #define REG_G_INPUTS_CHANGE_REQ 0x70000262 |
| 65 | #define REG_G_ACTIVE_PREV_CFG 0x70000266 |
| 66 | #define REG_G_PREV_CFG_CHG 0x70000268 |
| 67 | #define REG_G_PREV_OPEN_AFTER_CH 0x7000026a |
| 68 | |
| 69 | /* Preview context register sets. n = 0...4. */ |
| 70 | #define PREG(n, x) ((n) * 0x30 + (x)) |
| 71 | #define REG_P_OUT_WIDTH(n) PREG(n, 0x700002a6) |
| 72 | #define REG_P_OUT_HEIGHT(n) PREG(n, 0x700002a8) |
| 73 | #define REG_P_FMT(n) PREG(n, 0x700002aa) |
| 74 | #define REG_P_PVI_MASK(n) PREG(n, 0x700002b4) |
| 75 | #define REG_P_FR_TIME_TYPE(n) PREG(n, 0x700002be) |
| 76 | #define FR_TIME_DYNAMIC 0 |
| 77 | #define FR_TIME_FIXED 1 |
| 78 | #define FR_TIME_FIXED_ACCURATE 2 |
| 79 | #define REG_P_FR_TIME_Q_TYPE(n) PREG(n, 0x700002c0) |
| 80 | #define FR_TIME_Q_DYNAMIC 0 |
| 81 | #define FR_TIME_Q_BEST_FRRATE 1 |
| 82 | #define FR_TIME_Q_BEST_QUALITY 2 |
| 83 | |
| 84 | /* Frame period in 0.1 ms units */ |
| 85 | #define REG_P_MAX_FR_TIME(n) PREG(n, 0x700002c2) |
| 86 | #define REG_P_MIN_FR_TIME(n) PREG(n, 0x700002c4) |
| 87 | #define US_TO_FR_TIME(__t) ((__t) / 100) |
| 88 | #define REG_P_PREV_MIRROR(n) PREG(n, 0x700002d0) |
| 89 | #define REG_P_CAP_MIRROR(n) PREG(n, 0x700002d2) |
| 90 | |
| 91 | #define REG_G_PREVZOOM_IN_WIDTH 0x70000494 |
| 92 | #define REG_G_PREVZOOM_IN_HEIGHT 0x70000496 |
| 93 | #define REG_G_PREVZOOM_IN_XOFFS 0x70000498 |
| 94 | #define REG_G_PREVZOOM_IN_YOFFS 0x7000049a |
| 95 | #define REG_G_CAPZOOM_IN_WIDTH 0x7000049c |
| 96 | #define REG_G_CAPZOOM_IN_HEIGHT 0x7000049e |
| 97 | #define REG_G_CAPZOOM_IN_XOFFS 0x700004a0 |
| 98 | #define REG_G_CAPZOOM_IN_YOFFS 0x700004a2 |
| 99 | |
| 100 | /* n = 0...4 */ |
| 101 | #define REG_USER_SHARPNESS(n) (0x70000a28 + (n) * 0xb6) |
| 102 | |
| 103 | /* Reduce sharpness range for user space API */ |
| 104 | #define SHARPNESS_DIV 8208 |
| 105 | #define TOK_TERM 0xffffffff |
| 106 | |
| 107 | /* |
| 108 | * FIXME: This is copied from s5k6aa, because of no information |
| 109 | * in the S5K4ECGX datasheet. |
| 110 | * H/W register Interface (0xd0000000 - 0xd0000fff) |
| 111 | */ |
| 112 | #define AHB_MSB_ADDR_PTR 0xfcfc |
| 113 | #define GEN_REG_OFFSH 0xd000 |
| 114 | #define REG_CMDWR_ADDRH 0x0028 |
| 115 | #define REG_CMDWR_ADDRL 0x002a |
| 116 | #define REG_CMDRD_ADDRH 0x002c |
| 117 | #define REG_CMDRD_ADDRL 0x002e |
| 118 | #define REG_CMDBUF0_ADDR 0x0f12 |
| 119 | |
| 120 | struct s5k4ecgx_frmsize { |
| 121 | struct v4l2_frmsize_discrete size; |
| 122 | /* Fixed sensor matrix crop rectangle */ |
| 123 | struct v4l2_rect input_window; |
| 124 | }; |
| 125 | |
| 126 | struct regval_list { |
| 127 | u32 addr; |
| 128 | u16 val; |
| 129 | }; |
| 130 | |
| 131 | /* |
| 132 | * TODO: currently only preview is supported and snapshot (capture) |
| 133 | * is not implemented yet |
| 134 | */ |
| 135 | static const struct s5k4ecgx_frmsize s5k4ecgx_prev_sizes[] = { |
| 136 | { |
| 137 | .size = { 176, 144 }, |
| 138 | .input_window = { 0x00, 0x00, 0x928, 0x780 }, |
| 139 | }, { |
| 140 | .size = { 352, 288 }, |
| 141 | .input_window = { 0x00, 0x00, 0x928, 0x780 }, |
| 142 | }, { |
| 143 | .size = { 640, 480 }, |
| 144 | .input_window = { 0x00, 0x00, 0xa00, 0x780 }, |
| 145 | }, { |
| 146 | .size = { 720, 480 }, |
| 147 | .input_window = { 0x00, 0x00, 0xa00, 0x6a8 }, |
| 148 | } |
| 149 | }; |
| 150 | |
| 151 | #define S5K4ECGX_NUM_PREV ARRAY_SIZE(s5k4ecgx_prev_sizes) |
| 152 | |
| 153 | struct s5k4ecgx_pixfmt { |
Boris BREZILLON | f5fe58f | 2014-11-10 14:28:29 -0300 | [diff] [blame^] | 154 | u32 code; |
Sangwook Lee | 8b99312 | 2012-09-13 07:02:14 -0300 | [diff] [blame] | 155 | u32 colorspace; |
| 156 | /* REG_TC_PCFG_Format register value */ |
| 157 | u16 reg_p_format; |
| 158 | }; |
| 159 | |
| 160 | /* By default value, output from sensor will be YUV422 0-255 */ |
| 161 | static const struct s5k4ecgx_pixfmt s5k4ecgx_formats[] = { |
Boris BREZILLON | f5fe58f | 2014-11-10 14:28:29 -0300 | [diff] [blame^] | 162 | { MEDIA_BUS_FMT_YUYV8_2X8, V4L2_COLORSPACE_JPEG, 5 }, |
Sangwook Lee | 8b99312 | 2012-09-13 07:02:14 -0300 | [diff] [blame] | 163 | }; |
| 164 | |
| 165 | static const char * const s5k4ecgx_supply_names[] = { |
| 166 | /* |
| 167 | * Usually 2.8V is used for analog power (vdda) |
| 168 | * and digital IO (vddio, vdddcore) |
| 169 | */ |
| 170 | "vdda", |
| 171 | "vddio", |
| 172 | "vddcore", |
| 173 | "vddreg", /* The internal s5k4ecgx regulator's supply (1.8V) */ |
| 174 | }; |
| 175 | |
| 176 | #define S5K4ECGX_NUM_SUPPLIES ARRAY_SIZE(s5k4ecgx_supply_names) |
| 177 | |
| 178 | enum s5k4ecgx_gpio_id { |
| 179 | STBY, |
| 180 | RST, |
| 181 | GPIO_NUM, |
| 182 | }; |
| 183 | |
| 184 | struct s5k4ecgx { |
| 185 | struct v4l2_subdev sd; |
| 186 | struct media_pad pad; |
| 187 | struct v4l2_ctrl_handler handler; |
| 188 | |
| 189 | struct s5k4ecgx_platform_data *pdata; |
| 190 | const struct s5k4ecgx_pixfmt *curr_pixfmt; |
| 191 | const struct s5k4ecgx_frmsize *curr_frmsize; |
| 192 | struct mutex lock; |
| 193 | u8 streaming; |
| 194 | u8 set_params; |
| 195 | |
| 196 | struct regulator_bulk_data supplies[S5K4ECGX_NUM_SUPPLIES]; |
| 197 | struct s5k4ecgx_gpio gpio[GPIO_NUM]; |
| 198 | }; |
| 199 | |
| 200 | static inline struct s5k4ecgx *to_s5k4ecgx(struct v4l2_subdev *sd) |
| 201 | { |
| 202 | return container_of(sd, struct s5k4ecgx, sd); |
| 203 | } |
| 204 | |
| 205 | static int s5k4ecgx_i2c_read(struct i2c_client *client, u16 addr, u16 *val) |
| 206 | { |
| 207 | u8 wbuf[2] = { addr >> 8, addr & 0xff }; |
| 208 | struct i2c_msg msg[2]; |
| 209 | u8 rbuf[2]; |
| 210 | int ret; |
| 211 | |
| 212 | msg[0].addr = client->addr; |
| 213 | msg[0].flags = 0; |
| 214 | msg[0].len = 2; |
| 215 | msg[0].buf = wbuf; |
| 216 | |
| 217 | msg[1].addr = client->addr; |
| 218 | msg[1].flags = I2C_M_RD; |
| 219 | msg[1].len = 2; |
| 220 | msg[1].buf = rbuf; |
| 221 | |
| 222 | ret = i2c_transfer(client->adapter, msg, 2); |
| 223 | *val = be16_to_cpu(*((u16 *)rbuf)); |
| 224 | |
| 225 | v4l2_dbg(4, debug, client, "i2c_read: 0x%04X : 0x%04x\n", addr, *val); |
| 226 | |
| 227 | return ret == 2 ? 0 : ret; |
| 228 | } |
| 229 | |
| 230 | static int s5k4ecgx_i2c_write(struct i2c_client *client, u16 addr, u16 val) |
| 231 | { |
| 232 | u8 buf[4] = { addr >> 8, addr & 0xff, val >> 8, val & 0xff }; |
| 233 | |
| 234 | int ret = i2c_master_send(client, buf, 4); |
| 235 | v4l2_dbg(4, debug, client, "i2c_write: 0x%04x : 0x%04x\n", addr, val); |
| 236 | |
| 237 | return ret == 4 ? 0 : ret; |
| 238 | } |
| 239 | |
| 240 | static int s5k4ecgx_write(struct i2c_client *client, u32 addr, u16 val) |
| 241 | { |
| 242 | u16 high = addr >> 16, low = addr & 0xffff; |
| 243 | int ret; |
| 244 | |
| 245 | v4l2_dbg(3, debug, client, "write: 0x%08x : 0x%04x\n", addr, val); |
| 246 | |
| 247 | ret = s5k4ecgx_i2c_write(client, REG_CMDWR_ADDRH, high); |
| 248 | if (!ret) |
| 249 | ret = s5k4ecgx_i2c_write(client, REG_CMDWR_ADDRL, low); |
| 250 | if (!ret) |
| 251 | ret = s5k4ecgx_i2c_write(client, REG_CMDBUF0_ADDR, val); |
| 252 | |
| 253 | return ret; |
| 254 | } |
| 255 | |
| 256 | static int s5k4ecgx_read(struct i2c_client *client, u32 addr, u16 *val) |
| 257 | { |
| 258 | u16 high = addr >> 16, low = addr & 0xffff; |
| 259 | int ret; |
| 260 | |
| 261 | ret = s5k4ecgx_i2c_write(client, REG_CMDRD_ADDRH, high); |
| 262 | if (!ret) |
| 263 | ret = s5k4ecgx_i2c_write(client, REG_CMDRD_ADDRL, low); |
| 264 | if (!ret) |
| 265 | ret = s5k4ecgx_i2c_read(client, REG_CMDBUF0_ADDR, val); |
| 266 | if (!ret) |
| 267 | dev_err(&client->dev, "Failed to execute read command\n"); |
| 268 | |
| 269 | return ret; |
| 270 | } |
| 271 | |
| 272 | static int s5k4ecgx_read_fw_ver(struct v4l2_subdev *sd) |
| 273 | { |
| 274 | struct i2c_client *client = v4l2_get_subdevdata(sd); |
| 275 | u16 hw_rev, fw_ver = 0; |
| 276 | int ret; |
| 277 | |
| 278 | ret = s5k4ecgx_read(client, REG_FW_VERSION, &fw_ver); |
| 279 | if (ret < 0 || fw_ver != S5K4ECGX_FW_VERSION) { |
| 280 | v4l2_err(sd, "FW version check failed!\n"); |
| 281 | return -ENODEV; |
| 282 | } |
| 283 | |
| 284 | ret = s5k4ecgx_read(client, REG_FW_REVISION, &hw_rev); |
| 285 | if (ret < 0) |
| 286 | return ret; |
| 287 | |
| 288 | v4l2_info(sd, "chip found FW ver: 0x%x, HW rev: 0x%x\n", |
| 289 | fw_ver, hw_rev); |
| 290 | return 0; |
| 291 | } |
| 292 | |
| 293 | static int s5k4ecgx_set_ahb_address(struct v4l2_subdev *sd) |
| 294 | { |
| 295 | struct i2c_client *client = v4l2_get_subdevdata(sd); |
| 296 | int ret; |
| 297 | |
| 298 | /* Set APB peripherals start address */ |
| 299 | ret = s5k4ecgx_i2c_write(client, AHB_MSB_ADDR_PTR, GEN_REG_OFFSH); |
| 300 | if (ret < 0) |
| 301 | return ret; |
| 302 | /* |
| 303 | * FIXME: This is copied from s5k6aa, because of no information |
| 304 | * in s5k4ecgx's datasheet. |
| 305 | * sw_reset is activated to put device into idle status |
| 306 | */ |
| 307 | ret = s5k4ecgx_i2c_write(client, 0x0010, 0x0001); |
| 308 | if (ret < 0) |
| 309 | return ret; |
| 310 | |
| 311 | ret = s5k4ecgx_i2c_write(client, 0x1030, 0x0000); |
| 312 | if (ret < 0) |
| 313 | return ret; |
| 314 | /* Halt ARM CPU */ |
| 315 | return s5k4ecgx_i2c_write(client, 0x0014, 0x0001); |
| 316 | } |
| 317 | |
| 318 | #define FW_CRC_SIZE 4 |
| 319 | /* Register address, value are 4, 2 bytes */ |
| 320 | #define FW_RECORD_SIZE 6 |
| 321 | /* |
| 322 | * The firmware has following format: |
| 323 | * < total number of records (4 bytes + 2 bytes padding) N >, |
| 324 | * < record 0 >, ..., < record N - 1 >, < CRC32-CCITT (4-bytes) >, |
| 325 | * where "record" is a 4-byte register address followed by 2-byte |
| 326 | * register value (little endian). |
| 327 | * The firmware generator can be found in following git repository: |
| 328 | * git://git.linaro.org/people/sangwook/fimc-v4l2-app.git |
| 329 | */ |
| 330 | static int s5k4ecgx_load_firmware(struct v4l2_subdev *sd) |
| 331 | { |
| 332 | struct i2c_client *client = v4l2_get_subdevdata(sd); |
| 333 | const struct firmware *fw; |
| 334 | const u8 *ptr; |
| 335 | int err, i, regs_num; |
| 336 | u32 addr, crc, crc_file, addr_inc = 0; |
| 337 | u16 val; |
| 338 | |
| 339 | err = request_firmware(&fw, S5K4ECGX_FIRMWARE, sd->v4l2_dev->dev); |
| 340 | if (err) { |
| 341 | v4l2_err(sd, "Failed to read firmware %s\n", S5K4ECGX_FIRMWARE); |
| 342 | return err; |
| 343 | } |
| 344 | regs_num = le32_to_cpu(get_unaligned_le32(fw->data)); |
| 345 | |
Randy Dunlap | 107376b | 2012-10-16 16:17:59 -0300 | [diff] [blame] | 346 | v4l2_dbg(3, debug, sd, "FW: %s size %zu register sets %d\n", |
Sangwook Lee | 8b99312 | 2012-09-13 07:02:14 -0300 | [diff] [blame] | 347 | S5K4ECGX_FIRMWARE, fw->size, regs_num); |
| 348 | |
| 349 | regs_num++; /* Add header */ |
| 350 | if (fw->size != regs_num * FW_RECORD_SIZE + FW_CRC_SIZE) { |
| 351 | err = -EINVAL; |
| 352 | goto fw_out; |
| 353 | } |
| 354 | crc_file = le32_to_cpu(get_unaligned_le32(fw->data + |
| 355 | regs_num * FW_RECORD_SIZE)); |
| 356 | crc = crc32_le(~0, fw->data, regs_num * FW_RECORD_SIZE); |
| 357 | if (crc != crc_file) { |
| 358 | v4l2_err(sd, "FW: invalid crc (%#x:%#x)\n", crc, crc_file); |
| 359 | err = -EINVAL; |
| 360 | goto fw_out; |
| 361 | } |
| 362 | ptr = fw->data + FW_RECORD_SIZE; |
| 363 | for (i = 1; i < regs_num; i++) { |
| 364 | addr = le32_to_cpu(get_unaligned_le32(ptr)); |
| 365 | ptr += sizeof(u32); |
| 366 | val = le16_to_cpu(get_unaligned_le16(ptr)); |
| 367 | ptr += sizeof(u16); |
| 368 | if (addr - addr_inc != 2) |
| 369 | err = s5k4ecgx_write(client, addr, val); |
| 370 | else |
| 371 | err = s5k4ecgx_i2c_write(client, REG_CMDBUF0_ADDR, val); |
| 372 | if (err) |
| 373 | break; |
| 374 | addr_inc = addr; |
| 375 | } |
| 376 | fw_out: |
| 377 | release_firmware(fw); |
| 378 | return err; |
| 379 | } |
| 380 | |
| 381 | /* Set preview and capture input window */ |
| 382 | static int s5k4ecgx_set_input_window(struct i2c_client *c, |
| 383 | const struct v4l2_rect *r) |
| 384 | { |
| 385 | int ret; |
| 386 | |
| 387 | ret = s5k4ecgx_write(c, REG_G_PREV_IN_WIDTH, r->width); |
| 388 | if (!ret) |
| 389 | ret = s5k4ecgx_write(c, REG_G_PREV_IN_HEIGHT, r->height); |
| 390 | if (!ret) |
| 391 | ret = s5k4ecgx_write(c, REG_G_PREV_IN_XOFFS, r->left); |
| 392 | if (!ret) |
| 393 | ret = s5k4ecgx_write(c, REG_G_PREV_IN_YOFFS, r->top); |
| 394 | if (!ret) |
| 395 | ret = s5k4ecgx_write(c, REG_G_CAP_IN_WIDTH, r->width); |
| 396 | if (!ret) |
| 397 | ret = s5k4ecgx_write(c, REG_G_CAP_IN_HEIGHT, r->height); |
| 398 | if (!ret) |
| 399 | ret = s5k4ecgx_write(c, REG_G_CAP_IN_XOFFS, r->left); |
| 400 | if (!ret) |
| 401 | ret = s5k4ecgx_write(c, REG_G_CAP_IN_YOFFS, r->top); |
| 402 | |
| 403 | return ret; |
| 404 | } |
| 405 | |
| 406 | /* Set preview and capture zoom input window */ |
| 407 | static int s5k4ecgx_set_zoom_window(struct i2c_client *c, |
| 408 | const struct v4l2_rect *r) |
| 409 | { |
| 410 | int ret; |
| 411 | |
| 412 | ret = s5k4ecgx_write(c, REG_G_PREVZOOM_IN_WIDTH, r->width); |
| 413 | if (!ret) |
| 414 | ret = s5k4ecgx_write(c, REG_G_PREVZOOM_IN_HEIGHT, r->height); |
| 415 | if (!ret) |
| 416 | ret = s5k4ecgx_write(c, REG_G_PREVZOOM_IN_XOFFS, r->left); |
| 417 | if (!ret) |
| 418 | ret = s5k4ecgx_write(c, REG_G_PREVZOOM_IN_YOFFS, r->top); |
| 419 | if (!ret) |
| 420 | ret = s5k4ecgx_write(c, REG_G_CAPZOOM_IN_WIDTH, r->width); |
| 421 | if (!ret) |
| 422 | ret = s5k4ecgx_write(c, REG_G_CAPZOOM_IN_HEIGHT, r->height); |
| 423 | if (!ret) |
| 424 | ret = s5k4ecgx_write(c, REG_G_CAPZOOM_IN_XOFFS, r->left); |
| 425 | if (!ret) |
| 426 | ret = s5k4ecgx_write(c, REG_G_CAPZOOM_IN_YOFFS, r->top); |
| 427 | |
| 428 | return ret; |
| 429 | } |
| 430 | |
| 431 | static int s5k4ecgx_set_output_framefmt(struct s5k4ecgx *priv) |
| 432 | { |
| 433 | struct i2c_client *client = v4l2_get_subdevdata(&priv->sd); |
| 434 | int ret; |
| 435 | |
| 436 | ret = s5k4ecgx_write(client, REG_P_OUT_WIDTH(0), |
| 437 | priv->curr_frmsize->size.width); |
| 438 | if (!ret) |
| 439 | ret = s5k4ecgx_write(client, REG_P_OUT_HEIGHT(0), |
| 440 | priv->curr_frmsize->size.height); |
| 441 | if (!ret) |
| 442 | ret = s5k4ecgx_write(client, REG_P_FMT(0), |
| 443 | priv->curr_pixfmt->reg_p_format); |
| 444 | return ret; |
| 445 | } |
| 446 | |
| 447 | static int s5k4ecgx_init_sensor(struct v4l2_subdev *sd) |
| 448 | { |
| 449 | int ret; |
| 450 | |
| 451 | ret = s5k4ecgx_set_ahb_address(sd); |
| 452 | |
| 453 | /* The delay is from manufacturer's settings */ |
| 454 | msleep(100); |
| 455 | |
| 456 | if (!ret) |
| 457 | ret = s5k4ecgx_load_firmware(sd); |
| 458 | if (ret) |
| 459 | v4l2_err(sd, "Failed to write initial settings\n"); |
| 460 | |
| 461 | return ret; |
| 462 | } |
| 463 | |
| 464 | static int s5k4ecgx_gpio_set_value(struct s5k4ecgx *priv, int id, u32 val) |
| 465 | { |
| 466 | if (!gpio_is_valid(priv->gpio[id].gpio)) |
| 467 | return 0; |
| 468 | gpio_set_value(priv->gpio[id].gpio, val); |
| 469 | |
| 470 | return 1; |
| 471 | } |
| 472 | |
| 473 | static int __s5k4ecgx_power_on(struct s5k4ecgx *priv) |
| 474 | { |
| 475 | int ret; |
| 476 | |
| 477 | ret = regulator_bulk_enable(S5K4ECGX_NUM_SUPPLIES, priv->supplies); |
| 478 | if (ret) |
| 479 | return ret; |
| 480 | usleep_range(30, 50); |
| 481 | |
| 482 | /* The polarity of STBY is controlled by TSP */ |
| 483 | if (s5k4ecgx_gpio_set_value(priv, STBY, priv->gpio[STBY].level)) |
| 484 | usleep_range(30, 50); |
| 485 | |
| 486 | if (s5k4ecgx_gpio_set_value(priv, RST, priv->gpio[RST].level)) |
| 487 | usleep_range(30, 50); |
| 488 | |
| 489 | return 0; |
| 490 | } |
| 491 | |
| 492 | static int __s5k4ecgx_power_off(struct s5k4ecgx *priv) |
| 493 | { |
| 494 | if (s5k4ecgx_gpio_set_value(priv, RST, !priv->gpio[RST].level)) |
| 495 | usleep_range(30, 50); |
| 496 | |
| 497 | if (s5k4ecgx_gpio_set_value(priv, STBY, !priv->gpio[STBY].level)) |
| 498 | usleep_range(30, 50); |
| 499 | |
| 500 | priv->streaming = 0; |
| 501 | |
| 502 | return regulator_bulk_disable(S5K4ECGX_NUM_SUPPLIES, priv->supplies); |
| 503 | } |
| 504 | |
| 505 | /* Find nearest matching image pixel size. */ |
| 506 | static int s5k4ecgx_try_frame_size(struct v4l2_mbus_framefmt *mf, |
| 507 | const struct s5k4ecgx_frmsize **size) |
| 508 | { |
| 509 | unsigned int min_err = ~0; |
| 510 | int i = ARRAY_SIZE(s5k4ecgx_prev_sizes); |
| 511 | const struct s5k4ecgx_frmsize *fsize = &s5k4ecgx_prev_sizes[0], |
| 512 | *match = NULL; |
| 513 | |
| 514 | while (i--) { |
| 515 | int err = abs(fsize->size.width - mf->width) |
| 516 | + abs(fsize->size.height - mf->height); |
| 517 | if (err < min_err) { |
| 518 | min_err = err; |
| 519 | match = fsize; |
| 520 | } |
| 521 | fsize++; |
| 522 | } |
| 523 | if (match) { |
| 524 | mf->width = match->size.width; |
| 525 | mf->height = match->size.height; |
| 526 | if (size) |
| 527 | *size = match; |
| 528 | return 0; |
| 529 | } |
| 530 | |
| 531 | return -EINVAL; |
| 532 | } |
| 533 | |
| 534 | static int s5k4ecgx_enum_mbus_code(struct v4l2_subdev *sd, |
| 535 | struct v4l2_subdev_fh *fh, |
| 536 | struct v4l2_subdev_mbus_code_enum *code) |
| 537 | { |
| 538 | if (code->index >= ARRAY_SIZE(s5k4ecgx_formats)) |
| 539 | return -EINVAL; |
| 540 | code->code = s5k4ecgx_formats[code->index].code; |
| 541 | |
| 542 | return 0; |
| 543 | } |
| 544 | |
| 545 | static int s5k4ecgx_get_fmt(struct v4l2_subdev *sd, struct v4l2_subdev_fh *fh, |
| 546 | struct v4l2_subdev_format *fmt) |
| 547 | { |
| 548 | struct s5k4ecgx *priv = to_s5k4ecgx(sd); |
| 549 | struct v4l2_mbus_framefmt *mf; |
| 550 | |
| 551 | if (fmt->which == V4L2_SUBDEV_FORMAT_TRY) { |
| 552 | if (fh) { |
| 553 | mf = v4l2_subdev_get_try_format(fh, 0); |
| 554 | fmt->format = *mf; |
| 555 | } |
| 556 | return 0; |
| 557 | } |
| 558 | |
| 559 | mf = &fmt->format; |
| 560 | |
| 561 | mutex_lock(&priv->lock); |
| 562 | mf->width = priv->curr_frmsize->size.width; |
| 563 | mf->height = priv->curr_frmsize->size.height; |
| 564 | mf->code = priv->curr_pixfmt->code; |
| 565 | mf->colorspace = priv->curr_pixfmt->colorspace; |
| 566 | mf->field = V4L2_FIELD_NONE; |
| 567 | mutex_unlock(&priv->lock); |
| 568 | |
| 569 | return 0; |
| 570 | } |
| 571 | |
| 572 | static const struct s5k4ecgx_pixfmt *s5k4ecgx_try_fmt(struct v4l2_subdev *sd, |
| 573 | struct v4l2_mbus_framefmt *mf) |
| 574 | { |
| 575 | int i = ARRAY_SIZE(s5k4ecgx_formats); |
| 576 | |
| 577 | while (--i) |
| 578 | if (mf->code == s5k4ecgx_formats[i].code) |
| 579 | break; |
| 580 | mf->code = s5k4ecgx_formats[i].code; |
| 581 | |
| 582 | return &s5k4ecgx_formats[i]; |
| 583 | } |
| 584 | |
| 585 | static int s5k4ecgx_set_fmt(struct v4l2_subdev *sd, struct v4l2_subdev_fh *fh, |
| 586 | struct v4l2_subdev_format *fmt) |
| 587 | { |
| 588 | struct s5k4ecgx *priv = to_s5k4ecgx(sd); |
| 589 | const struct s5k4ecgx_frmsize *fsize = NULL; |
| 590 | const struct s5k4ecgx_pixfmt *pf; |
| 591 | struct v4l2_mbus_framefmt *mf; |
| 592 | int ret = 0; |
| 593 | |
| 594 | pf = s5k4ecgx_try_fmt(sd, &fmt->format); |
| 595 | s5k4ecgx_try_frame_size(&fmt->format, &fsize); |
| 596 | fmt->format.colorspace = V4L2_COLORSPACE_JPEG; |
Laurent Pinchart | 776a347 | 2014-05-19 12:04:32 -0300 | [diff] [blame] | 597 | fmt->format.field = V4L2_FIELD_NONE; |
Sangwook Lee | 8b99312 | 2012-09-13 07:02:14 -0300 | [diff] [blame] | 598 | |
| 599 | if (fmt->which == V4L2_SUBDEV_FORMAT_TRY) { |
| 600 | if (fh) { |
| 601 | mf = v4l2_subdev_get_try_format(fh, 0); |
| 602 | *mf = fmt->format; |
| 603 | } |
| 604 | return 0; |
| 605 | } |
| 606 | |
| 607 | mutex_lock(&priv->lock); |
| 608 | if (!priv->streaming) { |
| 609 | priv->curr_frmsize = fsize; |
| 610 | priv->curr_pixfmt = pf; |
| 611 | priv->set_params = 1; |
| 612 | } else { |
| 613 | ret = -EBUSY; |
| 614 | } |
| 615 | mutex_unlock(&priv->lock); |
| 616 | |
| 617 | return ret; |
| 618 | } |
| 619 | |
| 620 | static const struct v4l2_subdev_pad_ops s5k4ecgx_pad_ops = { |
| 621 | .enum_mbus_code = s5k4ecgx_enum_mbus_code, |
| 622 | .get_fmt = s5k4ecgx_get_fmt, |
| 623 | .set_fmt = s5k4ecgx_set_fmt, |
| 624 | }; |
| 625 | |
| 626 | /* |
| 627 | * V4L2 subdev controls |
| 628 | */ |
| 629 | static int s5k4ecgx_s_ctrl(struct v4l2_ctrl *ctrl) |
| 630 | { |
| 631 | struct v4l2_subdev *sd = &container_of(ctrl->handler, struct s5k4ecgx, |
| 632 | handler)->sd; |
| 633 | struct i2c_client *client = v4l2_get_subdevdata(sd); |
| 634 | struct s5k4ecgx *priv = to_s5k4ecgx(sd); |
| 635 | unsigned int i; |
| 636 | int err = 0; |
| 637 | |
| 638 | v4l2_dbg(1, debug, sd, "ctrl: 0x%x, value: %d\n", ctrl->id, ctrl->val); |
| 639 | |
| 640 | mutex_lock(&priv->lock); |
| 641 | switch (ctrl->id) { |
| 642 | case V4L2_CID_CONTRAST: |
| 643 | err = s5k4ecgx_write(client, REG_USER_CONTRAST, ctrl->val); |
| 644 | break; |
| 645 | |
| 646 | case V4L2_CID_SATURATION: |
| 647 | err = s5k4ecgx_write(client, REG_USER_SATURATION, ctrl->val); |
| 648 | break; |
| 649 | |
| 650 | case V4L2_CID_SHARPNESS: |
| 651 | /* TODO: Revisit, is this setting for all presets ? */ |
| 652 | for (i = 0; i < 4 && !err; i++) |
| 653 | err = s5k4ecgx_write(client, REG_USER_SHARPNESS(i), |
| 654 | ctrl->val * SHARPNESS_DIV); |
| 655 | break; |
| 656 | |
| 657 | case V4L2_CID_BRIGHTNESS: |
| 658 | err = s5k4ecgx_write(client, REG_USER_BRIGHTNESS, ctrl->val); |
| 659 | break; |
| 660 | } |
| 661 | mutex_unlock(&priv->lock); |
| 662 | if (err < 0) |
| 663 | v4l2_err(sd, "Failed to write s_ctrl err %d\n", err); |
| 664 | |
| 665 | return err; |
| 666 | } |
| 667 | |
| 668 | static const struct v4l2_ctrl_ops s5k4ecgx_ctrl_ops = { |
| 669 | .s_ctrl = s5k4ecgx_s_ctrl, |
| 670 | }; |
| 671 | |
| 672 | /* |
| 673 | * Reading s5k4ecgx version information |
| 674 | */ |
| 675 | static int s5k4ecgx_registered(struct v4l2_subdev *sd) |
| 676 | { |
| 677 | int ret; |
| 678 | struct s5k4ecgx *priv = to_s5k4ecgx(sd); |
| 679 | |
| 680 | mutex_lock(&priv->lock); |
| 681 | ret = __s5k4ecgx_power_on(priv); |
| 682 | if (!ret) { |
| 683 | ret = s5k4ecgx_read_fw_ver(sd); |
| 684 | __s5k4ecgx_power_off(priv); |
| 685 | } |
| 686 | mutex_unlock(&priv->lock); |
| 687 | |
| 688 | return ret; |
| 689 | } |
| 690 | |
| 691 | /* |
| 692 | * V4L2 subdev internal operations |
| 693 | */ |
| 694 | static int s5k4ecgx_open(struct v4l2_subdev *sd, struct v4l2_subdev_fh *fh) |
| 695 | { |
| 696 | struct v4l2_mbus_framefmt *mf = v4l2_subdev_get_try_format(fh, 0); |
| 697 | |
| 698 | mf->width = s5k4ecgx_prev_sizes[0].size.width; |
| 699 | mf->height = s5k4ecgx_prev_sizes[0].size.height; |
| 700 | mf->code = s5k4ecgx_formats[0].code; |
| 701 | mf->colorspace = V4L2_COLORSPACE_JPEG; |
| 702 | mf->field = V4L2_FIELD_NONE; |
| 703 | |
| 704 | return 0; |
| 705 | } |
| 706 | |
| 707 | static const struct v4l2_subdev_internal_ops s5k4ecgx_subdev_internal_ops = { |
| 708 | .registered = s5k4ecgx_registered, |
| 709 | .open = s5k4ecgx_open, |
| 710 | }; |
| 711 | |
| 712 | static int s5k4ecgx_s_power(struct v4l2_subdev *sd, int on) |
| 713 | { |
| 714 | struct s5k4ecgx *priv = to_s5k4ecgx(sd); |
| 715 | int ret; |
| 716 | |
| 717 | v4l2_dbg(1, debug, sd, "Switching %s\n", on ? "on" : "off"); |
| 718 | |
| 719 | if (on) { |
| 720 | ret = __s5k4ecgx_power_on(priv); |
| 721 | if (ret < 0) |
| 722 | return ret; |
| 723 | /* Time to stabilize sensor */ |
| 724 | msleep(100); |
| 725 | ret = s5k4ecgx_init_sensor(sd); |
| 726 | if (ret < 0) |
| 727 | __s5k4ecgx_power_off(priv); |
| 728 | else |
| 729 | priv->set_params = 1; |
| 730 | } else { |
| 731 | ret = __s5k4ecgx_power_off(priv); |
| 732 | } |
| 733 | |
| 734 | return ret; |
| 735 | } |
| 736 | |
| 737 | static int s5k4ecgx_log_status(struct v4l2_subdev *sd) |
| 738 | { |
| 739 | v4l2_ctrl_handler_log_status(sd->ctrl_handler, sd->name); |
| 740 | |
| 741 | return 0; |
| 742 | } |
| 743 | |
| 744 | static const struct v4l2_subdev_core_ops s5k4ecgx_core_ops = { |
| 745 | .s_power = s5k4ecgx_s_power, |
| 746 | .log_status = s5k4ecgx_log_status, |
| 747 | }; |
| 748 | |
| 749 | static int __s5k4ecgx_s_params(struct s5k4ecgx *priv) |
| 750 | { |
| 751 | struct i2c_client *client = v4l2_get_subdevdata(&priv->sd); |
| 752 | const struct v4l2_rect *crop_rect = &priv->curr_frmsize->input_window; |
| 753 | int ret; |
| 754 | |
| 755 | ret = s5k4ecgx_set_input_window(client, crop_rect); |
| 756 | if (!ret) |
| 757 | ret = s5k4ecgx_set_zoom_window(client, crop_rect); |
| 758 | if (!ret) |
| 759 | ret = s5k4ecgx_write(client, REG_G_INPUTS_CHANGE_REQ, 1); |
| 760 | if (!ret) |
| 761 | ret = s5k4ecgx_write(client, 0x70000a1e, 0x28); |
| 762 | if (!ret) |
| 763 | ret = s5k4ecgx_write(client, 0x70000ad4, 0x3c); |
| 764 | if (!ret) |
| 765 | ret = s5k4ecgx_set_output_framefmt(priv); |
| 766 | if (!ret) |
| 767 | ret = s5k4ecgx_write(client, REG_P_PVI_MASK(0), 0x52); |
| 768 | if (!ret) |
| 769 | ret = s5k4ecgx_write(client, REG_P_FR_TIME_TYPE(0), |
| 770 | FR_TIME_DYNAMIC); |
| 771 | if (!ret) |
| 772 | ret = s5k4ecgx_write(client, REG_P_FR_TIME_Q_TYPE(0), |
| 773 | FR_TIME_Q_BEST_FRRATE); |
| 774 | if (!ret) |
| 775 | ret = s5k4ecgx_write(client, REG_P_MIN_FR_TIME(0), |
| 776 | US_TO_FR_TIME(33300)); |
| 777 | if (!ret) |
| 778 | ret = s5k4ecgx_write(client, REG_P_MAX_FR_TIME(0), |
| 779 | US_TO_FR_TIME(66600)); |
| 780 | if (!ret) |
| 781 | ret = s5k4ecgx_write(client, REG_P_PREV_MIRROR(0), 0); |
| 782 | if (!ret) |
| 783 | ret = s5k4ecgx_write(client, REG_P_CAP_MIRROR(0), 0); |
| 784 | if (!ret) |
| 785 | ret = s5k4ecgx_write(client, REG_G_ACTIVE_PREV_CFG, 0); |
| 786 | if (!ret) |
| 787 | ret = s5k4ecgx_write(client, REG_G_PREV_OPEN_AFTER_CH, 1); |
| 788 | if (!ret) |
| 789 | ret = s5k4ecgx_write(client, REG_G_NEW_CFG_SYNC, 1); |
| 790 | if (!ret) |
| 791 | ret = s5k4ecgx_write(client, REG_G_PREV_CFG_CHG, 1); |
| 792 | |
| 793 | return ret; |
| 794 | } |
| 795 | |
| 796 | static int __s5k4ecgx_s_stream(struct s5k4ecgx *priv, int on) |
| 797 | { |
| 798 | struct i2c_client *client = v4l2_get_subdevdata(&priv->sd); |
| 799 | int ret; |
| 800 | |
| 801 | if (on && priv->set_params) { |
| 802 | ret = __s5k4ecgx_s_params(priv); |
| 803 | if (ret < 0) |
| 804 | return ret; |
| 805 | priv->set_params = 0; |
| 806 | } |
| 807 | /* |
| 808 | * This enables/disables preview stream only. Capture requests |
| 809 | * are not supported yet. |
| 810 | */ |
| 811 | ret = s5k4ecgx_write(client, REG_G_ENABLE_PREV, on); |
| 812 | if (ret < 0) |
| 813 | return ret; |
| 814 | return s5k4ecgx_write(client, REG_G_ENABLE_PREV_CHG, 1); |
| 815 | } |
| 816 | |
| 817 | static int s5k4ecgx_s_stream(struct v4l2_subdev *sd, int on) |
| 818 | { |
| 819 | struct s5k4ecgx *priv = to_s5k4ecgx(sd); |
| 820 | int ret = 0; |
| 821 | |
| 822 | v4l2_dbg(1, debug, sd, "Turn streaming %s\n", on ? "on" : "off"); |
| 823 | |
| 824 | mutex_lock(&priv->lock); |
| 825 | |
| 826 | if (priv->streaming == !on) { |
| 827 | ret = __s5k4ecgx_s_stream(priv, on); |
| 828 | if (!ret) |
| 829 | priv->streaming = on & 1; |
| 830 | } |
| 831 | |
| 832 | mutex_unlock(&priv->lock); |
| 833 | return ret; |
| 834 | } |
| 835 | |
| 836 | static const struct v4l2_subdev_video_ops s5k4ecgx_video_ops = { |
| 837 | .s_stream = s5k4ecgx_s_stream, |
| 838 | }; |
| 839 | |
| 840 | static const struct v4l2_subdev_ops s5k4ecgx_ops = { |
| 841 | .core = &s5k4ecgx_core_ops, |
| 842 | .pad = &s5k4ecgx_pad_ops, |
| 843 | .video = &s5k4ecgx_video_ops, |
| 844 | }; |
| 845 | |
| 846 | /* |
| 847 | * GPIO setup |
| 848 | */ |
| 849 | static int s5k4ecgx_config_gpio(int nr, int val, const char *name) |
| 850 | { |
| 851 | unsigned long flags = val ? GPIOF_OUT_INIT_HIGH : GPIOF_OUT_INIT_LOW; |
| 852 | int ret; |
| 853 | |
| 854 | if (!gpio_is_valid(nr)) |
| 855 | return 0; |
| 856 | ret = gpio_request_one(nr, flags, name); |
| 857 | if (!ret) |
| 858 | gpio_export(nr, 0); |
| 859 | |
| 860 | return ret; |
| 861 | } |
| 862 | |
| 863 | static void s5k4ecgx_free_gpios(struct s5k4ecgx *priv) |
| 864 | { |
| 865 | int i; |
| 866 | |
| 867 | for (i = 0; i < ARRAY_SIZE(priv->gpio); i++) { |
| 868 | if (!gpio_is_valid(priv->gpio[i].gpio)) |
| 869 | continue; |
| 870 | gpio_free(priv->gpio[i].gpio); |
| 871 | priv->gpio[i].gpio = -EINVAL; |
| 872 | } |
| 873 | } |
| 874 | |
| 875 | static int s5k4ecgx_config_gpios(struct s5k4ecgx *priv, |
| 876 | const struct s5k4ecgx_platform_data *pdata) |
| 877 | { |
| 878 | const struct s5k4ecgx_gpio *gpio = &pdata->gpio_stby; |
| 879 | int ret; |
| 880 | |
| 881 | priv->gpio[STBY].gpio = -EINVAL; |
| 882 | priv->gpio[RST].gpio = -EINVAL; |
| 883 | |
| 884 | ret = s5k4ecgx_config_gpio(gpio->gpio, gpio->level, "S5K4ECGX_STBY"); |
| 885 | |
| 886 | if (ret) { |
| 887 | s5k4ecgx_free_gpios(priv); |
| 888 | return ret; |
| 889 | } |
| 890 | priv->gpio[STBY] = *gpio; |
| 891 | if (gpio_is_valid(gpio->gpio)) |
| 892 | gpio_set_value(gpio->gpio, 0); |
| 893 | |
| 894 | gpio = &pdata->gpio_reset; |
| 895 | |
| 896 | ret = s5k4ecgx_config_gpio(gpio->gpio, gpio->level, "S5K4ECGX_RST"); |
| 897 | if (ret) { |
| 898 | s5k4ecgx_free_gpios(priv); |
| 899 | return ret; |
| 900 | } |
| 901 | priv->gpio[RST] = *gpio; |
| 902 | if (gpio_is_valid(gpio->gpio)) |
| 903 | gpio_set_value(gpio->gpio, 0); |
| 904 | |
| 905 | return 0; |
| 906 | } |
| 907 | |
| 908 | static int s5k4ecgx_init_v4l2_ctrls(struct s5k4ecgx *priv) |
| 909 | { |
| 910 | const struct v4l2_ctrl_ops *ops = &s5k4ecgx_ctrl_ops; |
| 911 | struct v4l2_ctrl_handler *hdl = &priv->handler; |
| 912 | int ret; |
| 913 | |
| 914 | ret = v4l2_ctrl_handler_init(hdl, 4); |
| 915 | if (ret) |
| 916 | return ret; |
| 917 | |
| 918 | v4l2_ctrl_new_std(hdl, ops, V4L2_CID_BRIGHTNESS, -208, 127, 1, 0); |
| 919 | v4l2_ctrl_new_std(hdl, ops, V4L2_CID_CONTRAST, -127, 127, 1, 0); |
| 920 | v4l2_ctrl_new_std(hdl, ops, V4L2_CID_SATURATION, -127, 127, 1, 0); |
| 921 | |
| 922 | /* Sharpness default is 24612, and then (24612/SHARPNESS_DIV) = 2 */ |
| 923 | v4l2_ctrl_new_std(hdl, ops, V4L2_CID_SHARPNESS, -32704/SHARPNESS_DIV, |
| 924 | 24612/SHARPNESS_DIV, 1, 2); |
| 925 | if (hdl->error) { |
| 926 | ret = hdl->error; |
| 927 | v4l2_ctrl_handler_free(hdl); |
| 928 | return ret; |
| 929 | } |
| 930 | priv->sd.ctrl_handler = hdl; |
| 931 | |
| 932 | return 0; |
| 933 | }; |
| 934 | |
| 935 | static int s5k4ecgx_probe(struct i2c_client *client, |
| 936 | const struct i2c_device_id *id) |
| 937 | { |
| 938 | struct s5k4ecgx_platform_data *pdata = client->dev.platform_data; |
| 939 | struct v4l2_subdev *sd; |
| 940 | struct s5k4ecgx *priv; |
| 941 | int ret, i; |
| 942 | |
| 943 | if (pdata == NULL) { |
| 944 | dev_err(&client->dev, "platform data is missing!\n"); |
| 945 | return -EINVAL; |
| 946 | } |
| 947 | |
| 948 | priv = devm_kzalloc(&client->dev, sizeof(struct s5k4ecgx), GFP_KERNEL); |
| 949 | if (!priv) |
| 950 | return -ENOMEM; |
| 951 | |
| 952 | mutex_init(&priv->lock); |
| 953 | priv->streaming = 0; |
| 954 | |
| 955 | sd = &priv->sd; |
| 956 | /* Registering subdev */ |
| 957 | v4l2_i2c_subdev_init(sd, client, &s5k4ecgx_ops); |
| 958 | strlcpy(sd->name, S5K4ECGX_DRIVER_NAME, sizeof(sd->name)); |
| 959 | |
| 960 | sd->internal_ops = &s5k4ecgx_subdev_internal_ops; |
| 961 | /* Support v4l2 sub-device user space API */ |
| 962 | sd->flags |= V4L2_SUBDEV_FL_HAS_DEVNODE; |
| 963 | |
| 964 | priv->pad.flags = MEDIA_PAD_FL_SOURCE; |
| 965 | sd->entity.type = MEDIA_ENT_T_V4L2_SUBDEV_SENSOR; |
| 966 | ret = media_entity_init(&sd->entity, 1, &priv->pad, 0); |
| 967 | if (ret) |
| 968 | return ret; |
| 969 | |
| 970 | ret = s5k4ecgx_config_gpios(priv, pdata); |
| 971 | if (ret) { |
| 972 | dev_err(&client->dev, "Failed to set gpios\n"); |
| 973 | goto out_err1; |
| 974 | } |
| 975 | for (i = 0; i < S5K4ECGX_NUM_SUPPLIES; i++) |
| 976 | priv->supplies[i].supply = s5k4ecgx_supply_names[i]; |
| 977 | |
| 978 | ret = devm_regulator_bulk_get(&client->dev, S5K4ECGX_NUM_SUPPLIES, |
| 979 | priv->supplies); |
| 980 | if (ret) { |
| 981 | dev_err(&client->dev, "Failed to get regulators\n"); |
| 982 | goto out_err2; |
| 983 | } |
| 984 | ret = s5k4ecgx_init_v4l2_ctrls(priv); |
| 985 | if (ret) |
| 986 | goto out_err2; |
| 987 | |
| 988 | priv->curr_pixfmt = &s5k4ecgx_formats[0]; |
| 989 | priv->curr_frmsize = &s5k4ecgx_prev_sizes[0]; |
| 990 | |
| 991 | return 0; |
| 992 | |
| 993 | out_err2: |
| 994 | s5k4ecgx_free_gpios(priv); |
| 995 | out_err1: |
| 996 | media_entity_cleanup(&priv->sd.entity); |
| 997 | |
| 998 | return ret; |
| 999 | } |
| 1000 | |
| 1001 | static int s5k4ecgx_remove(struct i2c_client *client) |
| 1002 | { |
| 1003 | struct v4l2_subdev *sd = i2c_get_clientdata(client); |
| 1004 | struct s5k4ecgx *priv = to_s5k4ecgx(sd); |
| 1005 | |
| 1006 | mutex_destroy(&priv->lock); |
| 1007 | s5k4ecgx_free_gpios(priv); |
| 1008 | v4l2_device_unregister_subdev(sd); |
| 1009 | v4l2_ctrl_handler_free(&priv->handler); |
| 1010 | media_entity_cleanup(&sd->entity); |
| 1011 | |
| 1012 | return 0; |
| 1013 | } |
| 1014 | |
| 1015 | static const struct i2c_device_id s5k4ecgx_id[] = { |
| 1016 | { S5K4ECGX_DRIVER_NAME, 0 }, |
| 1017 | {} |
| 1018 | }; |
| 1019 | MODULE_DEVICE_TABLE(i2c, s5k4ecgx_id); |
| 1020 | |
| 1021 | static struct i2c_driver v4l2_i2c_driver = { |
| 1022 | .driver = { |
| 1023 | .owner = THIS_MODULE, |
| 1024 | .name = S5K4ECGX_DRIVER_NAME, |
| 1025 | }, |
| 1026 | .probe = s5k4ecgx_probe, |
| 1027 | .remove = s5k4ecgx_remove, |
| 1028 | .id_table = s5k4ecgx_id, |
| 1029 | }; |
| 1030 | |
| 1031 | module_i2c_driver(v4l2_i2c_driver); |
| 1032 | |
| 1033 | MODULE_DESCRIPTION("Samsung S5K4ECGX 5MP SOC camera"); |
| 1034 | MODULE_AUTHOR("Sangwook Lee <sangwook.lee@linaro.org>"); |
| 1035 | MODULE_AUTHOR("Seok-Young Jang <quartz.jang@samsung.com>"); |
| 1036 | MODULE_LICENSE("GPL"); |
| 1037 | MODULE_FIRMWARE(S5K4ECGX_FIRMWARE); |