| /* |
| * animeo_ip.dts - Device Tree file for Somfy Animeo IP Boards |
| * |
| * Copyright (C) 2011-2012 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> |
| * |
| * Licensed under GPLv2 only. |
| */ |
| |
| /dts-v1/; |
| #include "at91sam9260.dtsi" |
| |
| / { |
| model = "Somfy Animeo IP"; |
| compatible = "somfy,animeo-ip", "atmel,at91sam9260", "atmel,at91sam9"; |
| |
| aliases { |
| serial0 = &usart1; |
| serial1 = &usart2; |
| serial2 = &usart0; |
| serial3 = &dbgu; |
| serial4 = &usart3; |
| serial5 = &uart0; |
| serial6 = &uart1; |
| }; |
| |
| chosen { |
| linux,stdout-path = &usart2; |
| }; |
| |
| memory { |
| reg = <0x20000000 0x4000000>; |
| }; |
| |
| clocks { |
| slow_xtal { |
| clock-frequency = <32768>; |
| }; |
| |
| main_xtal { |
| clock-frequency = <18432000>; |
| }; |
| }; |
| |
| ahb { |
| apb { |
| usart0: serial@fffb0000 { |
| pinctrl-0 = <&pinctrl_usart0 &pinctrl_usart0_rts>; |
| linux,rs485-enabled-at-boot-time; |
| status = "okay"; |
| }; |
| |
| usart1: serial@fffb4000 { |
| pinctrl-0 = <&pinctrl_usart1 &pinctrl_usart1_rts>; |
| linux,rs485-enabled-at-boot-time; |
| status = "okay"; |
| }; |
| |
| usart2: serial@fffb8000 { |
| pinctrl-0 = <&pinctrl_usart2>; |
| status = "okay"; |
| }; |
| |
| macb0: ethernet@fffc4000 { |
| pinctrl-0 = <&pinctrl_macb_rmii &pinctrl_macb_rmii_mii>; |
| phy-mode = "mii"; |
| status = "okay"; |
| }; |
| |
| mmc0: mmc@fffa8000 { |
| pinctrl-0 = <&pinctrl_mmc0_clk |
| &pinctrl_mmc0_slot1_cmd_dat0 |
| &pinctrl_mmc0_slot1_dat1_3>; |
| status = "okay"; |
| |
| slot@1 { |
| reg = <1>; |
| bus-width = <4>; |
| }; |
| }; |
| |
| watchdog@fffffd40 { |
| status = "okay"; |
| }; |
| }; |
| |
| nand0: nand@40000000 { |
| nand-bus-width = <8>; |
| nand-ecc-mode = "soft"; |
| nand-on-flash-bbt; |
| status = "okay"; |
| |
| barebox@0 { |
| label = "barebox"; |
| reg = <0x0 0x58000>; |
| }; |
| |
| u_boot_env@58000 { |
| label = "u_boot_env"; |
| reg = <0x58000 0x8000>; |
| }; |
| |
| ubi@60000 { |
| label = "ubi"; |
| reg = <0x60000 0x1FA0000>; |
| }; |
| }; |
| |
| usb0: ohci@500000 { |
| num-ports = <2>; |
| atmel,vbus-gpio = <&pioB 15 GPIO_ACTIVE_LOW>; |
| status = "okay"; |
| }; |
| }; |
| |
| leds { |
| compatible = "gpio-leds"; |
| |
| power_green { |
| label = "power_green"; |
| gpios = <&pioC 17 GPIO_ACTIVE_HIGH>; |
| linux,default-trigger = "heartbeat"; |
| }; |
| |
| power_red { |
| label = "power_red"; |
| gpios = <&pioA 2 GPIO_ACTIVE_HIGH>; |
| }; |
| |
| tx_green { |
| label = "tx_green"; |
| gpios = <&pioC 19 GPIO_ACTIVE_HIGH>; |
| }; |
| |
| tx_red { |
| label = "tx_red"; |
| gpios = <&pioC 18 GPIO_ACTIVE_HIGH>; |
| }; |
| }; |
| |
| gpio_keys { |
| compatible = "gpio-keys"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| keyswitch_in { |
| label = "keyswitch_in"; |
| gpios = <&pioB 1 GPIO_ACTIVE_HIGH>; |
| linux,code = <28>; |
| wakeup-source; |
| }; |
| |
| error_in { |
| label = "error_in"; |
| gpios = <&pioB 2 GPIO_ACTIVE_HIGH>; |
| linux,code = <29>; |
| wakeup-source; |
| }; |
| |
| btn { |
| label = "btn"; |
| gpios = <&pioC 23 GPIO_ACTIVE_HIGH>; |
| linux,code = <31>; |
| wakeup-source; |
| }; |
| }; |
| }; |