diff --git a/drivers/staging/iio/magnetometer/ak8975.c b/drivers/staging/iio/magnetometer/ak8975.c
index 420f206..d71904a 100644
--- a/drivers/staging/iio/magnetometer/ak8975.c
+++ b/drivers/staging/iio/magnetometer/ak8975.c
@@ -206,7 +206,7 @@
 	}
 
 	/* Precalculate scale factor for each axis and
-           store in the device data. */
+	   store in the device data. */
 	data->raw_to_gauss[0] = ((data->asa[0] + 128) * 30) >> 8;
 	data->raw_to_gauss[1] = ((data->asa[1] + 128) * 30) >> 8;
 	data->raw_to_gauss[2] = ((data->asa[2] + 128) * 30) >> 8;
@@ -316,6 +316,59 @@
 	return sprintf(buf, "%ld\n", data->raw_to_gauss[this_attr->address]);
 }
 
+static int wait_conversion_complete_gpio(struct ak8975_data *data)
+{
+	struct i2c_client *client = data->client;
+	u8 read_status;
+	u32 timeout_ms = AK8975_MAX_CONVERSION_TIMEOUT;
+	int ret;
+
+	/* Wait for the conversion to complete. */
+	while (timeout_ms) {
+		msleep(AK8975_CONVERSION_DONE_POLL_TIME);
+		if (gpio_get_value(data->eoc_gpio))
+			break;
+		timeout_ms -= AK8975_CONVERSION_DONE_POLL_TIME;
+	}
+	if (!timeout_ms) {
+		dev_err(&client->dev, "Conversion timeout happened\n");
+		return -EINVAL;
+	}
+
+	ret = ak8975_read_data(client, AK8975_REG_ST1, 1, &read_status);
+	if (ret < 0) {
+		dev_err(&client->dev, "Error in reading ST1\n");
+		return ret;
+	}
+	return read_status;
+}
+
+static int wait_conversion_complete_polled(struct ak8975_data *data)
+{
+	struct i2c_client *client = data->client;
+	u8 read_status;
+	u32 timeout_ms = AK8975_MAX_CONVERSION_TIMEOUT;
+	int ret;
+
+	/* Wait for the conversion to complete. */
+	while (timeout_ms) {
+		msleep(AK8975_CONVERSION_DONE_POLL_TIME);
+		ret = ak8975_read_data(client, AK8975_REG_ST1, 1, &read_status);
+		if (ret < 0) {
+			dev_err(&client->dev, "Error in reading ST1\n");
+			return ret;
+		}
+		if (read_status)
+			break;
+		timeout_ms -= AK8975_CONVERSION_DONE_POLL_TIME;
+	}
+	if (!timeout_ms) {
+		dev_err(&client->dev, "Conversion timeout happened\n");
+		return -EINVAL;
+	}
+	return read_status;
+}
+
 /*
  * Emits the raw flux value for the x, y, or z axis.
  */
@@ -326,7 +379,6 @@
 	struct ak8975_data *data = indio_dev->dev_data;
 	struct i2c_client *client = data->client;
 	struct iio_dev_attr *this_attr = to_iio_dev_attr(devattr);
-	u32 timeout_ms = AK8975_MAX_CONVERSION_TIMEOUT;
 	u16 meas_reg;
 	s16 raw;
 	u8 read_status;
@@ -352,23 +404,14 @@
 	}
 
 	/* Wait for the conversion to complete. */
-	while (timeout_ms) {
-		msleep(AK8975_CONVERSION_DONE_POLL_TIME);
-		if (gpio_get_value(data->eoc_gpio))
-			break;
-		timeout_ms -= AK8975_CONVERSION_DONE_POLL_TIME;
-	}
-	if (!timeout_ms) {
-		dev_err(&client->dev, "Conversion timeout happened\n");
-		ret = -EINVAL;
+	if (data->eoc_gpio)
+		ret = wait_conversion_complete_gpio(data);
+	else
+		ret = wait_conversion_complete_polled(data);
+	if (ret < 0)
 		goto exit;
-	}
 
-	ret = ak8975_read_data(client, AK8975_REG_ST1, 1, &read_status);
-	if (ret < 0) {
-		dev_err(&client->dev, "Error in reading ST1\n");
-		goto exit;
-	}
+	read_status = ret;
 
 	if (read_status & AK8975_REG_ST1_DRDY_MASK) {
 		ret = ak8975_read_data(client, AK8975_REG_ST2, 1, &read_status);
@@ -454,25 +497,26 @@
 	data->eoc_irq = client->irq;
 	data->eoc_gpio = irq_to_gpio(client->irq);
 
-	if (!data->eoc_gpio) {
-		dev_err(&client->dev, "failed, no valid GPIO\n");
-		err = -EINVAL;
-		goto exit_free;
-	}
+	/* We may not have a GPIO based IRQ to scan, that is fine, we will
+	   poll if so */
+	if (data->eoc_gpio > 0) {
+		err = gpio_request(data->eoc_gpio, "ak_8975");
+		if (err < 0) {
+			dev_err(&client->dev,
+				"failed to request GPIO %d, error %d\n",
+							data->eoc_gpio, err);
+			goto exit_free;
+		}
 
-	err = gpio_request(data->eoc_gpio, "ak_8975");
-	if (err < 0) {
-		dev_err(&client->dev, "failed to request GPIO %d, error %d\n",
-			data->eoc_gpio, err);
-		goto exit_free;
-	}
-
-	err = gpio_direction_input(data->eoc_gpio);
-	if (err < 0) {
-		dev_err(&client->dev, "Failed to configure input direction for"
-			" GPIO %d, error %d\n", data->eoc_gpio, err);
-		goto exit_gpio;
-	}
+		err = gpio_direction_input(data->eoc_gpio);
+		if (err < 0) {
+			dev_err(&client->dev,
+				"Failed to configure input direction for GPIO %d, error %d\n",
+						data->eoc_gpio, err);
+			goto exit_gpio;
+		}
+	} else
+		data->eoc_gpio = 0;	/* No GPIO available */
 
 	/* Perform some basic start-of-day setup of the device. */
 	err = ak8975_setup(client);
@@ -503,7 +547,8 @@
 exit_free_iio:
 	iio_free_device(data->indio_dev);
 exit_gpio:
-	gpio_free(data->eoc_gpio);
+	if (data->eoc_gpio)
+		gpio_free(data->eoc_gpio);
 exit_free:
 	kfree(data);
 exit:
@@ -517,7 +562,8 @@
 	iio_device_unregister(data->indio_dev);
 	iio_free_device(data->indio_dev);
 
-	gpio_free(data->eoc_gpio);
+	if (data->eoc_gpio)
+		gpio_free(data->eoc_gpio);
 
 	kfree(data);