diff --git a/arch/arm/mach-davinci/include/mach/spi.h b/arch/arm/mach-davinci/include/mach/spi.h
index 1f8b786..38f4da5 100644
--- a/arch/arm/mach-davinci/include/mach/spi.h
+++ b/arch/arm/mach-davinci/include/mach/spi.h
@@ -26,6 +26,20 @@
 	SPI_VERSION_2, /* For DA8xx */
 };
 
+/**
+ * davinci_spi_platform_data - Platform data for SPI master device on DaVinci
+ *
+ * @version:	version of the SPI IP. Different DaVinci devices have slightly
+ *		varying versions of the same IP.
+ * @num_chipselect: number of chipselects supported by this SPI master
+ * @intr_line:	interrupt line used to connect the SPI IP to the ARM interrupt
+ *		controller withn the SoC. Possible values are 0 and 1.
+ * @chip_sel:	list of GPIOs which can act as chip-selects for the SPI.
+ *		SPI_INTERN_CS denotes internal SPI chip-select. Not necessary
+ *		to populate if all chip-selects are internal.
+ * @cshold_bug:	set this to true if the SPI controller on your chip requires
+ *		a write to CSHOLD bit in between transfers (like in DM355).
+ */
 struct davinci_spi_platform_data {
 	u8	version;
 	u8	num_chipselect;
@@ -34,6 +48,24 @@
 	bool	cshold_bug;
 };
 
+/**
+ * davinci_spi_config - Per-chip-select configuration for SPI slave devices
+ *
+ * @wdelay:	amount of delay between transmissions. Measured in number of
+ *		SPI module clocks.
+ * @odd_parity:	polarity of parity flag at the end of transmit data stream.
+ *		0 - odd parity, 1 - even parity.
+ * @parity_enable: enable transmission of parity at end of each transmit
+ *		data stream.
+ * @io_type:	type of IO transfer. Choose between polled, interrupt and DMA.
+ * @timer_disable: disable chip-select timers (setup and hold)
+ * @c2tdelay:	chip-select setup time. Measured in number of SPI module clocks.
+ * @t2cdelay:	chip-select hold time. Measured in number of SPI module clocks.
+ * @t2edelay:	transmit data finished to SPI ENAn pin inactive time. Measured
+ *		in number of SPI clocks.
+ * @c2edelay:	chip-select active to SPI ENAn signal active time. Measured in
+ *		number of SPI clocks.
+ */
 struct davinci_spi_config {
 	u8	wdelay;
 	u8	odd_parity;
diff --git a/drivers/spi/davinci_spi.c b/drivers/spi/davinci_spi.c
index 2ec5fd2..f40f1be 100644
--- a/drivers/spi/davinci_spi.c
+++ b/drivers/spi/davinci_spi.c
@@ -787,6 +787,13 @@
 /**
  * davinci_spi_probe - probe function for SPI Master Controller
  * @pdev: platform_device structure which contains plateform specific data
+ *
+ * According to Linux Device Model this function will be invoked by Linux
+ * with platform_device struct which contains the device specific info.
+ * This function will map the SPI controller's memory, register IRQ,
+ * Reset SPI controller and setting its registers to default value.
+ * It will invoke spi_bitbang_start to create work queue so that client driver
+ * can register transfer method to work queue.
  */
 static int davinci_spi_probe(struct platform_device *pdev)
 {