diff --git a/Documentation/devicetree/bindings/thermal/imx-thermal.txt b/Documentation/devicetree/bindings/thermal/imx-thermal.txt
new file mode 100644
index 0000000..541c25e
--- /dev/null
+++ b/Documentation/devicetree/bindings/thermal/imx-thermal.txt
@@ -0,0 +1,17 @@
+* Temperature Monitor (TEMPMON) on Freescale i.MX SoCs
+
+Required properties:
+- compatible : "fsl,imx6q-thermal"
+- fsl,tempmon : phandle pointer to system controller that contains TEMPMON
+  control registers, e.g. ANATOP on imx6q.
+- fsl,tempmon-data : phandle pointer to fuse controller that contains TEMPMON
+  calibration data, e.g. OCOTP on imx6q.  The details about calibration data
+  can be found in SoC Reference Manual.
+
+Example:
+
+tempmon {
+	compatible = "fsl,imx6q-tempmon";
+	fsl,tempmon = <&anatop>;
+	fsl,tempmon-data = <&ocotp>;
+};
diff --git a/drivers/thermal/Kconfig b/drivers/thermal/Kconfig
index 34fa688..ae18f02 100644
--- a/drivers/thermal/Kconfig
+++ b/drivers/thermal/Kconfig
@@ -91,6 +91,17 @@
 	  because userland can easily disable the thermal policy by simply
 	  flooding this sysfs node with low temperature values.
 
+config IMX_THERMAL
+	tristate "Temperature sensor driver for Freescale i.MX SoCs"
+	depends on CPU_THERMAL
+	depends on MFD_SYSCON
+	depends on OF
+	help
+	  Support for Temperature Monitor (TEMPMON) found on Freescale i.MX SoCs.
+	  It supports one critical trip point and one passive trip point.  The
+	  cpufreq is used as the cooling device to throttle CPUs when the
+	  passive trip is crossed.
+
 config SPEAR_THERMAL
 	bool "SPEAr thermal sensor driver"
 	depends on PLAT_SPEAR
diff --git a/drivers/thermal/Makefile b/drivers/thermal/Makefile
index 1f27ada..c19df7a 100644
--- a/drivers/thermal/Makefile
+++ b/drivers/thermal/Makefile
@@ -21,6 +21,7 @@
 obj-$(CONFIG_DOVE_THERMAL)  	+= dove_thermal.o
 obj-$(CONFIG_DB8500_THERMAL)	+= db8500_thermal.o
 obj-$(CONFIG_ARMADA_THERMAL)	+= armada_thermal.o
+obj-$(CONFIG_IMX_THERMAL)	+= imx_thermal.o
 obj-$(CONFIG_DB8500_CPUFREQ_COOLING)	+= db8500_cpufreq_cooling.o
 obj-$(CONFIG_INTEL_POWERCLAMP)	+= intel_powerclamp.o
 obj-$(CONFIG_X86_PKG_TEMP_THERMAL)	+= x86_pkg_temp_thermal.o
diff --git a/drivers/thermal/cpu_cooling.c b/drivers/thermal/cpu_cooling.c
index 82e15db..5b3744e 100644
--- a/drivers/thermal/cpu_cooling.c
+++ b/drivers/thermal/cpu_cooling.c
@@ -322,6 +322,8 @@
 
 	if (cpumask_test_cpu(policy->cpu, &notify_device->allowed_cpus))
 		max_freq = notify_device->cpufreq_val;
+	else
+		return 0;
 
 	/* Never exceed user_policy.max */
 	if (max_freq > policy->user_policy.max)
diff --git a/drivers/thermal/imx_thermal.c b/drivers/thermal/imx_thermal.c
new file mode 100644
index 0000000..1d6c801
--- /dev/null
+++ b/drivers/thermal/imx_thermal.c
@@ -0,0 +1,541 @@
+/*
+ * Copyright 2013 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ */
+
+#include <linux/cpu_cooling.h>
+#include <linux/cpufreq.h>
+#include <linux/delay.h>
+#include <linux/device.h>
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/kernel.h>
+#include <linux/mfd/syscon.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+#include <linux/slab.h>
+#include <linux/thermal.h>
+#include <linux/types.h>
+
+#define REG_SET		0x4
+#define REG_CLR		0x8
+#define REG_TOG		0xc
+
+#define MISC0				0x0150
+#define MISC0_REFTOP_SELBIASOFF		(1 << 3)
+
+#define TEMPSENSE0			0x0180
+#define TEMPSENSE0_ALARM_VALUE_SHIFT	20
+#define TEMPSENSE0_ALARM_VALUE_MASK	(0xfff << TEMPSENSE0_ALARM_VALUE_SHIFT)
+#define TEMPSENSE0_TEMP_CNT_SHIFT	8
+#define TEMPSENSE0_TEMP_CNT_MASK	(0xfff << TEMPSENSE0_TEMP_CNT_SHIFT)
+#define TEMPSENSE0_FINISHED		(1 << 2)
+#define TEMPSENSE0_MEASURE_TEMP		(1 << 1)
+#define TEMPSENSE0_POWER_DOWN		(1 << 0)
+
+#define TEMPSENSE1			0x0190
+#define TEMPSENSE1_MEASURE_FREQ		0xffff
+
+#define OCOTP_ANA1			0x04e0
+
+/* The driver supports 1 passive trip point and 1 critical trip point */
+enum imx_thermal_trip {
+	IMX_TRIP_PASSIVE,
+	IMX_TRIP_CRITICAL,
+	IMX_TRIP_NUM,
+};
+
+/*
+ * It defines the temperature in millicelsius for passive trip point
+ * that will trigger cooling action when crossed.
+ */
+#define IMX_TEMP_PASSIVE		85000
+
+#define IMX_POLLING_DELAY		2000 /* millisecond */
+#define IMX_PASSIVE_DELAY		1000
+
+struct imx_thermal_data {
+	struct thermal_zone_device *tz;
+	struct thermal_cooling_device *cdev;
+	enum thermal_device_mode mode;
+	struct regmap *tempmon;
+	int c1, c2; /* See formula in imx_get_sensor_data() */
+	unsigned long temp_passive;
+	unsigned long temp_critical;
+	unsigned long alarm_temp;
+	unsigned long last_temp;
+	bool irq_enabled;
+	int irq;
+};
+
+static void imx_set_alarm_temp(struct imx_thermal_data *data,
+			       signed long alarm_temp)
+{
+	struct regmap *map = data->tempmon;
+	int alarm_value;
+
+	data->alarm_temp = alarm_temp;
+	alarm_value = (alarm_temp - data->c2) / data->c1;
+	regmap_write(map, TEMPSENSE0 + REG_CLR, TEMPSENSE0_ALARM_VALUE_MASK);
+	regmap_write(map, TEMPSENSE0 + REG_SET, alarm_value <<
+			TEMPSENSE0_ALARM_VALUE_SHIFT);
+}
+
+static int imx_get_temp(struct thermal_zone_device *tz, unsigned long *temp)
+{
+	struct imx_thermal_data *data = tz->devdata;
+	struct regmap *map = data->tempmon;
+	unsigned int n_meas;
+	bool wait;
+	u32 val;
+
+	if (data->mode == THERMAL_DEVICE_ENABLED) {
+		/* Check if a measurement is currently in progress */
+		regmap_read(map, TEMPSENSE0, &val);
+		wait = !(val & TEMPSENSE0_FINISHED);
+	} else {
+		/*
+		 * Every time we measure the temperature, we will power on the
+		 * temperature sensor, enable measurements, take a reading,
+		 * disable measurements, power off the temperature sensor.
+		 */
+		regmap_write(map, TEMPSENSE0 + REG_CLR, TEMPSENSE0_POWER_DOWN);
+		regmap_write(map, TEMPSENSE0 + REG_SET, TEMPSENSE0_MEASURE_TEMP);
+
+		wait = true;
+	}
+
+	/*
+	 * According to the temp sensor designers, it may require up to ~17us
+	 * to complete a measurement.
+	 */
+	if (wait)
+		usleep_range(20, 50);
+
+	regmap_read(map, TEMPSENSE0, &val);
+
+	if (data->mode != THERMAL_DEVICE_ENABLED) {
+		regmap_write(map, TEMPSENSE0 + REG_CLR, TEMPSENSE0_MEASURE_TEMP);
+		regmap_write(map, TEMPSENSE0 + REG_SET, TEMPSENSE0_POWER_DOWN);
+	}
+
+	if ((val & TEMPSENSE0_FINISHED) == 0) {
+		dev_dbg(&tz->device, "temp measurement never finished\n");
+		return -EAGAIN;
+	}
+
+	n_meas = (val & TEMPSENSE0_TEMP_CNT_MASK) >> TEMPSENSE0_TEMP_CNT_SHIFT;
+
+	/* See imx_get_sensor_data() for formula derivation */
+	*temp = data->c2 + data->c1 * n_meas;
+
+	/* Update alarm value to next higher trip point */
+	if (data->alarm_temp == data->temp_passive && *temp >= data->temp_passive)
+		imx_set_alarm_temp(data, data->temp_critical);
+	if (data->alarm_temp == data->temp_critical && *temp < data->temp_passive) {
+		imx_set_alarm_temp(data, data->temp_passive);
+		dev_dbg(&tz->device, "thermal alarm off: T < %lu\n",
+			data->alarm_temp / 1000);
+	}
+
+	if (*temp != data->last_temp) {
+		dev_dbg(&tz->device, "millicelsius: %ld\n", *temp);
+		data->last_temp = *temp;
+	}
+
+	/* Reenable alarm IRQ if temperature below alarm temperature */
+	if (!data->irq_enabled && *temp < data->alarm_temp) {
+		data->irq_enabled = true;
+		enable_irq(data->irq);
+	}
+
+	return 0;
+}
+
+static int imx_get_mode(struct thermal_zone_device *tz,
+			enum thermal_device_mode *mode)
+{
+	struct imx_thermal_data *data = tz->devdata;
+
+	*mode = data->mode;
+
+	return 0;
+}
+
+static int imx_set_mode(struct thermal_zone_device *tz,
+			enum thermal_device_mode mode)
+{
+	struct imx_thermal_data *data = tz->devdata;
+	struct regmap *map = data->tempmon;
+
+	if (mode == THERMAL_DEVICE_ENABLED) {
+		tz->polling_delay = IMX_POLLING_DELAY;
+		tz->passive_delay = IMX_PASSIVE_DELAY;
+
+		regmap_write(map, TEMPSENSE0 + REG_CLR, TEMPSENSE0_POWER_DOWN);
+		regmap_write(map, TEMPSENSE0 + REG_SET, TEMPSENSE0_MEASURE_TEMP);
+
+		if (!data->irq_enabled) {
+			data->irq_enabled = true;
+			enable_irq(data->irq);
+		}
+	} else {
+		regmap_write(map, TEMPSENSE0 + REG_CLR, TEMPSENSE0_MEASURE_TEMP);
+		regmap_write(map, TEMPSENSE0 + REG_SET, TEMPSENSE0_POWER_DOWN);
+
+		tz->polling_delay = 0;
+		tz->passive_delay = 0;
+
+		if (data->irq_enabled) {
+			disable_irq(data->irq);
+			data->irq_enabled = false;
+		}
+	}
+
+	data->mode = mode;
+	thermal_zone_device_update(tz);
+
+	return 0;
+}
+
+static int imx_get_trip_type(struct thermal_zone_device *tz, int trip,
+			     enum thermal_trip_type *type)
+{
+	*type = (trip == IMX_TRIP_PASSIVE) ? THERMAL_TRIP_PASSIVE :
+					     THERMAL_TRIP_CRITICAL;
+	return 0;
+}
+
+static int imx_get_crit_temp(struct thermal_zone_device *tz,
+			     unsigned long *temp)
+{
+	struct imx_thermal_data *data = tz->devdata;
+
+	*temp = data->temp_critical;
+	return 0;
+}
+
+static int imx_get_trip_temp(struct thermal_zone_device *tz, int trip,
+			     unsigned long *temp)
+{
+	struct imx_thermal_data *data = tz->devdata;
+
+	*temp = (trip == IMX_TRIP_PASSIVE) ? data->temp_passive :
+					     data->temp_critical;
+	return 0;
+}
+
+static int imx_set_trip_temp(struct thermal_zone_device *tz, int trip,
+			     unsigned long temp)
+{
+	struct imx_thermal_data *data = tz->devdata;
+
+	if (trip == IMX_TRIP_CRITICAL)
+		return -EPERM;
+
+	if (temp > IMX_TEMP_PASSIVE)
+		return -EINVAL;
+
+	data->temp_passive = temp;
+
+	imx_set_alarm_temp(data, temp);
+
+	return 0;
+}
+
+static int imx_bind(struct thermal_zone_device *tz,
+		    struct thermal_cooling_device *cdev)
+{
+	int ret;
+
+	ret = thermal_zone_bind_cooling_device(tz, IMX_TRIP_PASSIVE, cdev,
+					       THERMAL_NO_LIMIT,
+					       THERMAL_NO_LIMIT);
+	if (ret) {
+		dev_err(&tz->device,
+			"binding zone %s with cdev %s failed:%d\n",
+			tz->type, cdev->type, ret);
+		return ret;
+	}
+
+	return 0;
+}
+
+static int imx_unbind(struct thermal_zone_device *tz,
+		      struct thermal_cooling_device *cdev)
+{
+	int ret;
+
+	ret = thermal_zone_unbind_cooling_device(tz, IMX_TRIP_PASSIVE, cdev);
+	if (ret) {
+		dev_err(&tz->device,
+			"unbinding zone %s with cdev %s failed:%d\n",
+			tz->type, cdev->type, ret);
+		return ret;
+	}
+
+	return 0;
+}
+
+static const struct thermal_zone_device_ops imx_tz_ops = {
+	.bind = imx_bind,
+	.unbind = imx_unbind,
+	.get_temp = imx_get_temp,
+	.get_mode = imx_get_mode,
+	.set_mode = imx_set_mode,
+	.get_trip_type = imx_get_trip_type,
+	.get_trip_temp = imx_get_trip_temp,
+	.get_crit_temp = imx_get_crit_temp,
+	.set_trip_temp = imx_set_trip_temp,
+};
+
+static int imx_get_sensor_data(struct platform_device *pdev)
+{
+	struct imx_thermal_data *data = platform_get_drvdata(pdev);
+	struct regmap *map;
+	int t1, t2, n1, n2;
+	int ret;
+	u32 val;
+
+	map = syscon_regmap_lookup_by_phandle(pdev->dev.of_node,
+					      "fsl,tempmon-data");
+	if (IS_ERR(map)) {
+		ret = PTR_ERR(map);
+		dev_err(&pdev->dev, "failed to get sensor regmap: %d\n", ret);
+		return ret;
+	}
+
+	ret = regmap_read(map, OCOTP_ANA1, &val);
+	if (ret) {
+		dev_err(&pdev->dev, "failed to read sensor data: %d\n", ret);
+		return ret;
+	}
+
+	if (val == 0 || val == ~0) {
+		dev_err(&pdev->dev, "invalid sensor calibration data\n");
+		return -EINVAL;
+	}
+
+	/*
+	 * Sensor data layout:
+	 *   [31:20] - sensor value @ 25C
+	 *    [19:8] - sensor value of hot
+	 *     [7:0] - hot temperature value
+	 */
+	n1 = val >> 20;
+	n2 = (val & 0xfff00) >> 8;
+	t2 = val & 0xff;
+	t1 = 25; /* t1 always 25C */
+
+	/*
+	 * Derived from linear interpolation,
+	 * Tmeas = T2 + (Nmeas - N2) * (T1 - T2) / (N1 - N2)
+	 * We want to reduce this down to the minimum computation necessary
+	 * for each temperature read.  Also, we want Tmeas in millicelsius
+	 * and we don't want to lose precision from integer division. So...
+	 * milli_Tmeas = 1000 * T2 + 1000 * (Nmeas - N2) * (T1 - T2) / (N1 - N2)
+	 * Let constant c1 = 1000 * (T1 - T2) / (N1 - N2)
+	 * milli_Tmeas = (1000 * T2) + c1 * (Nmeas - N2)
+	 * milli_Tmeas = (1000 * T2) + (c1 * Nmeas) - (c1 * N2)
+	 * Let constant c2 = (1000 * T2) - (c1 * N2)
+	 * milli_Tmeas = c2 + (c1 * Nmeas)
+	 */
+	data->c1 = 1000 * (t1 - t2) / (n1 - n2);
+	data->c2 = 1000 * t2 - data->c1 * n2;
+
+	/*
+	 * Set the default passive cooling trip point to 20 °C below the
+	 * maximum die temperature. Can be changed from userspace.
+	 */
+	data->temp_passive = 1000 * (t2 - 20);
+
+	/*
+	 * The maximum die temperature is t2, let's give 5 °C cushion
+	 * for noise and possible temperature rise between measurements.
+	 */
+	data->temp_critical = 1000 * (t2 - 5);
+
+	return 0;
+}
+
+static irqreturn_t imx_thermal_alarm_irq(int irq, void *dev)
+{
+	struct imx_thermal_data *data = dev;
+
+	disable_irq_nosync(irq);
+	data->irq_enabled = false;
+
+	return IRQ_WAKE_THREAD;
+}
+
+static irqreturn_t imx_thermal_alarm_irq_thread(int irq, void *dev)
+{
+	struct imx_thermal_data *data = dev;
+
+	dev_dbg(&data->tz->device, "THERMAL ALARM: T > %lu\n",
+		data->alarm_temp / 1000);
+
+	thermal_zone_device_update(data->tz);
+
+	return IRQ_HANDLED;
+}
+
+static int imx_thermal_probe(struct platform_device *pdev)
+{
+	struct imx_thermal_data *data;
+	struct cpumask clip_cpus;
+	struct regmap *map;
+	int measure_freq;
+	int ret;
+
+	data = devm_kzalloc(&pdev->dev, sizeof(*data), GFP_KERNEL);
+	if (!data)
+		return -ENOMEM;
+
+	map = syscon_regmap_lookup_by_phandle(pdev->dev.of_node, "fsl,tempmon");
+	if (IS_ERR(map)) {
+		ret = PTR_ERR(map);
+		dev_err(&pdev->dev, "failed to get tempmon regmap: %d\n", ret);
+		return ret;
+	}
+	data->tempmon = map;
+
+	data->irq = platform_get_irq(pdev, 0);
+	if (data->irq < 0)
+		return data->irq;
+
+	ret = devm_request_threaded_irq(&pdev->dev, data->irq,
+			imx_thermal_alarm_irq, imx_thermal_alarm_irq_thread,
+			0, "imx_thermal", data);
+	if (ret < 0) {
+		dev_err(&pdev->dev, "failed to request alarm irq: %d\n", ret);
+		return ret;
+	}
+
+	platform_set_drvdata(pdev, data);
+
+	ret = imx_get_sensor_data(pdev);
+	if (ret) {
+		dev_err(&pdev->dev, "failed to get sensor data\n");
+		return ret;
+	}
+
+	/* Make sure sensor is in known good state for measurements */
+	regmap_write(map, TEMPSENSE0 + REG_CLR, TEMPSENSE0_POWER_DOWN);
+	regmap_write(map, TEMPSENSE0 + REG_CLR, TEMPSENSE0_MEASURE_TEMP);
+	regmap_write(map, TEMPSENSE1 + REG_CLR, TEMPSENSE1_MEASURE_FREQ);
+	regmap_write(map, MISC0 + REG_SET, MISC0_REFTOP_SELBIASOFF);
+	regmap_write(map, TEMPSENSE0 + REG_SET, TEMPSENSE0_POWER_DOWN);
+
+	cpumask_set_cpu(0, &clip_cpus);
+	data->cdev = cpufreq_cooling_register(&clip_cpus);
+	if (IS_ERR(data->cdev)) {
+		ret = PTR_ERR(data->cdev);
+		dev_err(&pdev->dev,
+			"failed to register cpufreq cooling device: %d\n", ret);
+		return ret;
+	}
+
+	data->tz = thermal_zone_device_register("imx_thermal_zone",
+						IMX_TRIP_NUM,
+						BIT(IMX_TRIP_PASSIVE), data,
+						&imx_tz_ops, NULL,
+						IMX_PASSIVE_DELAY,
+						IMX_POLLING_DELAY);
+	if (IS_ERR(data->tz)) {
+		ret = PTR_ERR(data->tz);
+		dev_err(&pdev->dev,
+			"failed to register thermal zone device %d\n", ret);
+		cpufreq_cooling_unregister(data->cdev);
+		return ret;
+	}
+
+	/* Enable measurements at ~ 10 Hz */
+	regmap_write(map, TEMPSENSE1 + REG_CLR, TEMPSENSE1_MEASURE_FREQ);
+	measure_freq = DIV_ROUND_UP(32768, 10); /* 10 Hz */
+	regmap_write(map, TEMPSENSE1 + REG_SET, measure_freq);
+	imx_set_alarm_temp(data, data->temp_passive);
+	regmap_write(map, TEMPSENSE0 + REG_CLR, TEMPSENSE0_POWER_DOWN);
+	regmap_write(map, TEMPSENSE0 + REG_SET, TEMPSENSE0_MEASURE_TEMP);
+
+	data->irq_enabled = true;
+	data->mode = THERMAL_DEVICE_ENABLED;
+
+	return 0;
+}
+
+static int imx_thermal_remove(struct platform_device *pdev)
+{
+	struct imx_thermal_data *data = platform_get_drvdata(pdev);
+	struct regmap *map = data->tempmon;
+
+	/* Disable measurements */
+	regmap_write(map, TEMPSENSE0 + REG_SET, TEMPSENSE0_POWER_DOWN);
+
+	thermal_zone_device_unregister(data->tz);
+	cpufreq_cooling_unregister(data->cdev);
+
+	return 0;
+}
+
+#ifdef CONFIG_PM_SLEEP
+static int imx_thermal_suspend(struct device *dev)
+{
+	struct imx_thermal_data *data = dev_get_drvdata(dev);
+	struct regmap *map = data->tempmon;
+	u32 val;
+
+	regmap_read(map, TEMPSENSE0, &val);
+	if ((val & TEMPSENSE0_POWER_DOWN) == 0) {
+		/*
+		 * If a measurement is taking place, wait for a long enough
+		 * time for it to finish, and then check again.  If it still
+		 * does not finish, something must go wrong.
+		 */
+		udelay(50);
+		regmap_read(map, TEMPSENSE0, &val);
+		if ((val & TEMPSENSE0_POWER_DOWN) == 0)
+			return -ETIMEDOUT;
+	}
+
+	return 0;
+}
+
+static int imx_thermal_resume(struct device *dev)
+{
+	/* Nothing to do for now */
+	return 0;
+}
+#endif
+
+static SIMPLE_DEV_PM_OPS(imx_thermal_pm_ops,
+			 imx_thermal_suspend, imx_thermal_resume);
+
+static const struct of_device_id of_imx_thermal_match[] = {
+	{ .compatible = "fsl,imx6q-tempmon", },
+	{ /* end */ }
+};
+
+static struct platform_driver imx_thermal = {
+	.driver = {
+		.name	= "imx_thermal",
+		.owner  = THIS_MODULE,
+		.pm	= &imx_thermal_pm_ops,
+		.of_match_table = of_imx_thermal_match,
+	},
+	.probe		= imx_thermal_probe,
+	.remove		= imx_thermal_remove,
+};
+module_platform_driver(imx_thermal);
+
+MODULE_AUTHOR("Freescale Semiconductor, Inc.");
+MODULE_DESCRIPTION("Thermal driver for Freescale i.MX SoCs");
+MODULE_LICENSE("GPL v2");
+MODULE_ALIAS("platform:imx-thermal");