drivers/media/radio/Kconfig

#
# Multimedia Video device configuration
#

menu "Radio Adapters"
	depends on VIDEO_DEV

config RADIO_CADET
	tristate "ADS Cadet AM/FM Tuner"
	depends on ISA && VIDEO_V4L2
	---help---
	  Choose Y here if you have one of these AM/FM radio cards, and then
	  fill in the port address below.

	  In order to control your radio card, you will need to use programs
	  that are compatible with the Video For Linux API.  Information on
	  this API and pointers to "v4l" programs may be found at
	  <file:Documentation/video4linux/API.html>.

	  Further documentation on this driver can be found on the WWW at
	  <http://linux.blackhawke.net/cadet/>.

	  To compile this driver as a module, choose M here: the
	  module will be called radio-cadet.

config RADIO_RTRACK
	tristate "AIMSlab RadioTrack (aka RadioReveal) support"
	depends on ISA && VIDEO_V4L2
	---help---
	  Choose Y here if you have one of these FM radio cards, and then fill
	  in the port address below.

	  Note that newer AIMSlab RadioTrack cards have a different chipset
	  and are not supported by this driver.  For these cards, use the
	  RadioTrack II driver below.

	  If you have a GemTeks combined (PnP) sound- and radio card you must
	  use this driver as a module and setup the card with isapnptools.
	  You must also pass the module a suitable io parameter, 0x248 has
	  been reported to be used by these cards.

	  In order to control your radio card, you will need to use programs
	  that are compatible with the Video For Linux API.  Information on
	  this API and pointers to "v4l" programs may be found at
	  <file:Documentation/video4linux/API.html>. More information is
	  contained in the file
	  <file:Documentation/video4linux/radiotrack.txt>.

	  To compile this driver as a module, choose M here: the
	  module will be called radio-aimslab.

config RADIO_RTRACK_PORT
	hex "RadioTrack i/o port (0x20f or 0x30f)"
	depends on RADIO_RTRACK=y
	default "20f"
	help
	  Enter either 0x30f or 0x20f here.  The card default is 0x30f, if you
	  haven't changed the jumper setting on the card.

config RADIO_RTRACK2
	tristate "AIMSlab RadioTrack II support"
	depends on ISA && VIDEO_V4L2
	---help---
	  Choose Y here if you have this FM radio card, and then fill in the
	  port address below.

	  In order to control your radio card, you will need to use programs
	  that are compatible with the Video For Linux API.  Information on
	  this API and pointers to "v4l" programs may be found at
	  <file:Documentation/video4linux/API.html>.

	  To compile this driver as a module, choose M here: the
	  module will be called radio-rtrack2.

config RADIO_RTRACK2_PORT
	hex "RadioTrack II i/o port (0x20c or 0x30c)"
	depends on RADIO_RTRACK2=y
	default "30c"
	help
	  Enter either 0x30c or 0x20c here.  The card default is 0x30c, if you
	  haven't changed the jumper setting on the card.

config RADIO_AZTECH
	tristate "Aztech/Packard Bell Radio"
	depends on ISA && VIDEO_V4L2
	---help---
	  Choose Y here if you have one of these FM radio cards, and then fill
	  in the port address below.

	  In order to control your radio card, you will need to use programs
	  that are compatible with the Video For Linux API.  Information on
	  this API and pointers to "v4l" programs may be found at
	  <file:Documentation/video4linux/API.html>.

	  To compile this driver as a module, choose M here: the
	  module will be called radio-aztech.

config RADIO_AZTECH_PORT
	hex "Aztech/Packard Bell I/O port (0x350 or 0x358)"
	depends on RADIO_AZTECH=y
	default "350"
	help
	  Enter either 0x350 or 0x358 here.  The card default is 0x350, if you
	  haven't changed the setting of jumper JP3 on the card.  Removing the
	  jumper sets the card to 0x358.

config RADIO_GEMTEK
	tristate "GemTek Radio Card support"
	depends on ISA && VIDEO_V4L2
	---help---
	  Choose Y here if you have this FM radio card, and then fill in the
	  port address below.

	  In order to control your radio card, you will need to use programs
	  that are compatible with the Video For Linux API.  Information on
	  this API and pointers to "v4l" programs may be found at
	  <file:Documentation/video4linux/API.html>.

	  To compile this driver as a module, choose M here: the
	  module will be called radio-gemtek.

config RADIO_GEMTEK_PORT
	hex "GemTek i/o port (0x20c, 0x30c, 0x24c or 0x34c)"
	depends on RADIO_GEMTEK=y
	default "34c"
	help
	  Enter either 0x20c, 0x30c, 0x24c or 0x34c here. The card default is
	  0x34c, if you haven't changed the jumper setting on the card. On
	  Sound Vision 16 Gold PnP with FM Radio (ESS1869+FM Gemtek), the I/O
	  port is 0x28c.

config RADIO_GEMTEK_PCI
	tristate "GemTek PCI Radio Card support"
	depends on VIDEO_V4L2 && PCI
	---help---
	  Choose Y here if you have this PCI FM radio card.

	  In order to control your radio card, you will need to use programs
	  that are compatible with the Video for Linux API.  Information on
	  this API and pointers to "v4l" programs may be found at
	  <file:Documentation/video4linux/API.html>.

	  To compile this driver as a module, choose M here: the
	  module will be called radio-gemtek-pci.

config RADIO_MAXIRADIO
	tristate "Guillemot MAXI Radio FM 2000 radio"
	depends on VIDEO_V4L2 && PCI
	---help---
	  Choose Y here if you have this radio card.  This card may also be
	  found as Gemtek PCI FM.

	  In order to control your radio card, you will need to use programs
	  that are compatible with the Video For Linux API.  Information on
	  this API and pointers to "v4l" programs may be found at
	  <file:Documentation/video4linux/API.html>.

	  To compile this driver as a module, choose M here: the
	  module will be called radio-maxiradio.

config RADIO_MAESTRO
	tristate "Maestro on board radio"
	depends on VIDEO_V4L2 && PCI
	---help---
	  Say Y here to directly support the on-board radio tuner on the
	  Maestro 2 or 2E sound card.

	  In order to control your radio card, you will need to use programs
	  that are compatible with the Video For Linux API.  Information on
	  this API and pointers to "v4l" programs may be found at
	  <file:Documentation/video4linux/API.html>.

	  To compile this driver as a module, choose M here: the
	  module will be called radio-maestro.

config RADIO_SF16FMI
	tristate "SF16FMI Radio"
	depends on ISA && VIDEO_V4L2
	---help---
	  Choose Y here if you have one of these FM radio cards.  If you
	  compile the driver into the kernel and your card is not PnP one, you
	  have to add "sf16fm=<io>" to the kernel command line (I/O address is
	  0x284 or 0x384).

	  In order to control your radio card, you will need to use programs
	  that are compatible with the Video For Linux API.  Information on
	  this API and pointers to "v4l" programs may be found at
	  <file:Documentation/video4linux/API.html>.

	  To compile this driver as a module, choose M here: the
	  module will be called radio-sf16fmi.

config RADIO_SF16FMR2
	tristate "SF16FMR2 Radio"
	depends on ISA && VIDEO_V4L2
	---help---
	  Choose Y here if you have one of these FM radio cards.

	  In order to control your radio card, you will need to use programs
	  that are compatible with the Video For Linux API.  Information on
	  this API and pointers to "v4l" programs may be found on the WWW at
	  <http://roadrunner.swansea.uk.linux.org/v4l.shtml>.

	  To compile this driver as a module, choose M here: the
	  module will be called radio-sf16fmr2.

config RADIO_TERRATEC
	tristate "TerraTec ActiveRadio ISA Standalone"
	depends on ISA && VIDEO_V4L2
	---help---
	  Choose Y here if you have this FM radio card, and then fill in the
	  port address below. (TODO)

	  Note: This driver is in its early stages.  Right now volume and
	  frequency control and muting works at least for me, but
	  unfortunately I have not found anybody who wants to use this card
	  with Linux.  So if it is this what YOU are trying to do right now,
	  PLEASE DROP ME A NOTE!!  Rolf Offermanns <rolf@offermanns.de>.

	  In order to control your radio card, you will need to use programs
	  that are compatible with the Video For Linux API.  Information on
	  this API and pointers to "v4l" programs may be found at
	  <file:Documentation/video4linux/API.html>.

	  To compile this driver as a module, choose M here: the
	  module will be called radio-terratec.

config RADIO_TERRATEC_PORT
	hex "Terratec i/o port (normally 0x590)"
	depends on RADIO_TERRATEC=y
	default "590"
	help
	  Fill in the I/O port of your TerraTec FM radio card. If unsure, go
	  with the default.

config RADIO_TRUST
	tristate "Trust FM radio card"
	depends on ISA && VIDEO_V4L2
	help
	  This is a driver for the Trust FM radio cards. Say Y if you have
	  such a card and want to use it under Linux.

	  To compile this driver as a module, choose M here: the
	  module will be called radio-trust.

config RADIO_TRUST_PORT
	hex "Trust i/o port (usually 0x350 or 0x358)"
	depends on RADIO_TRUST=y
	default "350"
	help
	  Enter the I/O port of your Trust FM radio card. If unsure, try the
	  values "0x350" or "0x358".

config RADIO_TYPHOON
	tristate "Typhoon Radio (a.k.a. EcoRadio)"
	depends on ISA && VIDEO_V4L2
	---help---
	  Choose Y here if you have one of these FM radio cards, and then fill
	  in the port address and the frequency used for muting below.

	  In order to control your radio card, you will need to use programs
	  that are compatible with the Video For Linux API.  Information on
	  this API and pointers to "v4l" programs may be found at
	  <file:Documentation/video4linux/API.html>.

	  To compile this driver as a module, choose M here: the
	  module will be called radio-typhoon.

config RADIO_TYPHOON_PROC_FS
	bool "Support for /proc/radio-typhoon"
	depends on PROC_FS && RADIO_TYPHOON
	help
	  Say Y here if you want the typhoon radio card driver to write
	  status information (frequency, volume, muted, mute frequency,
	  base address) to /proc/radio-typhoon. The file can be viewed with
	  your favorite pager (i.e. use "more /proc/radio-typhoon" or "less
	  /proc/radio-typhoon" or simply "cat /proc/radio-typhoon").

config RADIO_TYPHOON_PORT
	hex "Typhoon I/O port (0x316 or 0x336)"
	depends on RADIO_TYPHOON=y
	default "316"
	help
	  Enter the I/O port of your Typhoon or EcoRadio radio card.

config RADIO_TYPHOON_MUTEFREQ
	int "Typhoon frequency set when muting the device (kHz)"
	depends on RADIO_TYPHOON=y
	default "87500"
	help
	  Enter the frequency used for muting the radio. The device is never
	  completely silent. If the volume is just turned down, you can still
	  hear silent voices and music. For that reason, the frequency of the
	  radio device is set to the frequency you can enter here whenever
	  the device is muted. There should be no local radio station at that
	  frequency.

config RADIO_ZOLTRIX
	tristate "Zoltrix Radio"
	depends on ISA && VIDEO_V4L2
	---help---
	  Choose Y here if you have one of these FM radio cards, and then fill
	  in the port address below.

	  In order to control your radio card, you will need to use programs
	  that are compatible with the Video For Linux API.  Information on
	  this API and pointers to "v4l" programs may be found at
	  <file:Documentation/video4linux/API.html>.

	  To compile this driver as a module, choose M here: the
	  module will be called radio-zoltrix.

config RADIO_ZOLTRIX_PORT
	hex "ZOLTRIX I/O port (0x20c or 0x30c)"
	depends on RADIO_ZOLTRIX=y
	default "20c"
	help
	  Enter the I/O port of your Zoltrix radio card.

config USB_DSBR
	tristate "D-Link USB FM radio support (EXPERIMENTAL)"
	depends on USB && VIDEO_V4L2 && EXPERIMENTAL
	---help---
	  Say Y here if you want to connect this type of radio to your
	  computer's USB port. Note that the audio is not digital, and
	  you must connect the line out connector to a sound card or a
	  set of speakers.

	  To compile this driver as a module, choose M here: the
	  module will be called dsbr100.
endmenu