| /* |
| * arch/arm/mach-orion5x/rd88f5182-setup.c |
| * |
| * Marvell Orion-NAS Reference Design Setup |
| * |
| * Maintainer: Ronen Shitrit <rshitrit@marvell.com> |
| * |
| * This file is licensed under the terms of the GNU General Public |
| * License version 2. This program is licensed "as is" without any |
| * warranty of any kind, whether express or implied. |
| */ |
| |
| #include <linux/kernel.h> |
| #include <linux/init.h> |
| #include <linux/platform_device.h> |
| #include <linux/pci.h> |
| #include <linux/irq.h> |
| #include <linux/mtd/physmap.h> |
| #include <linux/mv643xx_eth.h> |
| #include <linux/ata_platform.h> |
| #include <linux/i2c.h> |
| #include <asm/mach-types.h> |
| #include <asm/gpio.h> |
| #include <asm/leds.h> |
| #include <asm/mach/arch.h> |
| #include <asm/mach/pci.h> |
| #include <asm/arch/orion5x.h> |
| #include "common.h" |
| |
| /***************************************************************************** |
| * RD-88F5182 Info |
| ****************************************************************************/ |
| |
| /* |
| * 512K NOR flash Device bus boot chip select |
| */ |
| |
| #define RD88F5182_NOR_BOOT_BASE 0xf4000000 |
| #define RD88F5182_NOR_BOOT_SIZE SZ_512K |
| |
| /* |
| * 16M NOR flash on Device bus chip select 1 |
| */ |
| |
| #define RD88F5182_NOR_BASE 0xfc000000 |
| #define RD88F5182_NOR_SIZE SZ_16M |
| |
| /* |
| * PCI |
| */ |
| |
| #define RD88F5182_PCI_SLOT0_OFFS 7 |
| #define RD88F5182_PCI_SLOT0_IRQ_A_PIN 7 |
| #define RD88F5182_PCI_SLOT0_IRQ_B_PIN 6 |
| |
| /* |
| * GPIO Debug LED |
| */ |
| |
| #define RD88F5182_GPIO_DBG_LED 0 |
| |
| /***************************************************************************** |
| * 16M NOR Flash on Device bus CS1 |
| ****************************************************************************/ |
| |
| static struct physmap_flash_data rd88f5182_nor_flash_data = { |
| .width = 1, |
| }; |
| |
| static struct resource rd88f5182_nor_flash_resource = { |
| .flags = IORESOURCE_MEM, |
| .start = RD88F5182_NOR_BASE, |
| .end = RD88F5182_NOR_BASE + RD88F5182_NOR_SIZE - 1, |
| }; |
| |
| static struct platform_device rd88f5182_nor_flash = { |
| .name = "physmap-flash", |
| .id = 0, |
| .dev = { |
| .platform_data = &rd88f5182_nor_flash_data, |
| }, |
| .num_resources = 1, |
| .resource = &rd88f5182_nor_flash_resource, |
| }; |
| |
| #ifdef CONFIG_LEDS |
| |
| /***************************************************************************** |
| * Use GPIO debug led as CPU active indication |
| ****************************************************************************/ |
| |
| static void rd88f5182_dbgled_event(led_event_t evt) |
| { |
| int val; |
| |
| if (evt == led_idle_end) |
| val = 1; |
| else if (evt == led_idle_start) |
| val = 0; |
| else |
| return; |
| |
| gpio_set_value(RD88F5182_GPIO_DBG_LED, val); |
| } |
| |
| static int __init rd88f5182_dbgled_init(void) |
| { |
| int pin; |
| |
| if (machine_is_rd88f5182()) { |
| pin = RD88F5182_GPIO_DBG_LED; |
| |
| if (gpio_request(pin, "DBGLED") == 0) { |
| if (gpio_direction_output(pin, 0) != 0) { |
| printk(KERN_ERR "rd88f5182_dbgled_init failed " |
| "to set output pin %d\n", pin); |
| gpio_free(pin); |
| return 0; |
| } |
| } else { |
| printk(KERN_ERR "rd88f5182_dbgled_init failed " |
| "to request gpio %d\n", pin); |
| return 0; |
| } |
| |
| leds_event = rd88f5182_dbgled_event; |
| } |
| |
| return 0; |
| } |
| |
| __initcall(rd88f5182_dbgled_init); |
| |
| #endif |
| |
| /***************************************************************************** |
| * PCI |
| ****************************************************************************/ |
| |
| void __init rd88f5182_pci_preinit(void) |
| { |
| int pin; |
| |
| /* |
| * Configure PCI GPIO IRQ pins |
| */ |
| pin = RD88F5182_PCI_SLOT0_IRQ_A_PIN; |
| if (gpio_request(pin, "PCI IntA") == 0) { |
| if (gpio_direction_input(pin) == 0) { |
| set_irq_type(gpio_to_irq(pin), IRQT_LOW); |
| } else { |
| printk(KERN_ERR "rd88f5182_pci_preinit faield to " |
| "set_irq_type pin %d\n", pin); |
| gpio_free(pin); |
| } |
| } else { |
| printk(KERN_ERR "rd88f5182_pci_preinit failed to request gpio %d\n", pin); |
| } |
| |
| pin = RD88F5182_PCI_SLOT0_IRQ_B_PIN; |
| if (gpio_request(pin, "PCI IntB") == 0) { |
| if (gpio_direction_input(pin) == 0) { |
| set_irq_type(gpio_to_irq(pin), IRQT_LOW); |
| } else { |
| printk(KERN_ERR "rd88f5182_pci_preinit faield to " |
| "set_irq_type pin %d\n", pin); |
| gpio_free(pin); |
| } |
| } else { |
| printk(KERN_ERR "rd88f5182_pci_preinit failed to gpio_request %d\n", pin); |
| } |
| } |
| |
| static int __init rd88f5182_pci_map_irq(struct pci_dev *dev, u8 slot, u8 pin) |
| { |
| int irq; |
| |
| /* |
| * Check for devices with hard-wired IRQs. |
| */ |
| irq = orion5x_pci_map_irq(dev, slot, pin); |
| if (irq != -1) |
| return irq; |
| |
| /* |
| * PCI IRQs are connected via GPIOs |
| */ |
| switch (slot - RD88F5182_PCI_SLOT0_OFFS) { |
| case 0: |
| if (pin == 1) |
| return gpio_to_irq(RD88F5182_PCI_SLOT0_IRQ_A_PIN); |
| else |
| return gpio_to_irq(RD88F5182_PCI_SLOT0_IRQ_B_PIN); |
| default: |
| return -1; |
| } |
| } |
| |
| static struct hw_pci rd88f5182_pci __initdata = { |
| .nr_controllers = 2, |
| .preinit = rd88f5182_pci_preinit, |
| .swizzle = pci_std_swizzle, |
| .setup = orion5x_pci_sys_setup, |
| .scan = orion5x_pci_sys_scan_bus, |
| .map_irq = rd88f5182_pci_map_irq, |
| }; |
| |
| static int __init rd88f5182_pci_init(void) |
| { |
| if (machine_is_rd88f5182()) |
| pci_common_init(&rd88f5182_pci); |
| |
| return 0; |
| } |
| |
| subsys_initcall(rd88f5182_pci_init); |
| |
| /***************************************************************************** |
| * Ethernet |
| ****************************************************************************/ |
| |
| static struct mv643xx_eth_platform_data rd88f5182_eth_data = { |
| .phy_addr = 8, |
| .force_phy_addr = 1, |
| }; |
| |
| /***************************************************************************** |
| * RTC DS1338 on I2C bus |
| ****************************************************************************/ |
| static struct i2c_board_info __initdata rd88f5182_i2c_rtc = { |
| I2C_BOARD_INFO("ds1338", 0x68), |
| }; |
| |
| /***************************************************************************** |
| * Sata |
| ****************************************************************************/ |
| static struct mv_sata_platform_data rd88f5182_sata_data = { |
| .n_ports = 2, |
| }; |
| |
| /***************************************************************************** |
| * General Setup |
| ****************************************************************************/ |
| static void __init rd88f5182_init(void) |
| { |
| /* |
| * Setup basic Orion functions. Need to be called early. |
| */ |
| orion5x_init(); |
| |
| /* |
| * Open a special address decode windows for the PCIe WA. |
| */ |
| orion5x_setup_pcie_wa_win(ORION5X_PCIE_WA_PHYS_BASE, |
| ORION5X_PCIE_WA_SIZE); |
| |
| /* |
| * Setup Multiplexing Pins -- |
| * MPP[0] Debug Led (GPIO - Out) |
| * MPP[1] Debug Led (GPIO - Out) |
| * MPP[2] N/A |
| * MPP[3] RTC_Int (GPIO - In) |
| * MPP[4] GPIO |
| * MPP[5] GPIO |
| * MPP[6] PCI_intA (GPIO - In) |
| * MPP[7] PCI_intB (GPIO - In) |
| * MPP[8-11] N/A |
| * MPP[12] SATA 0 presence Indication |
| * MPP[13] SATA 1 presence Indication |
| * MPP[14] SATA 0 active Indication |
| * MPP[15] SATA 1 active indication |
| * MPP[16-19] Not used |
| * MPP[20] PCI Clock to MV88F5182 |
| * MPP[21] PCI Clock to mini PCI CON11 |
| * MPP[22] USB 0 over current indication |
| * MPP[23] USB 1 over current indication |
| * MPP[24] USB 1 over current enable |
| * MPP[25] USB 0 over current enable |
| */ |
| |
| orion5x_write(MPP_0_7_CTRL, 0x00000003); |
| orion5x_write(MPP_8_15_CTRL, 0x55550000); |
| orion5x_write(MPP_16_19_CTRL, 0x5555); |
| |
| orion5x_gpio_set_valid_pins(0x000000fb); |
| |
| /* |
| * Configure peripherals. |
| */ |
| orion5x_ehci0_init(); |
| orion5x_ehci1_init(); |
| orion5x_eth_init(&rd88f5182_eth_data); |
| orion5x_i2c_init(); |
| orion5x_sata_init(&rd88f5182_sata_data); |
| orion5x_uart0_init(); |
| |
| orion5x_setup_dev_boot_win(RD88F5182_NOR_BOOT_BASE, |
| RD88F5182_NOR_BOOT_SIZE); |
| |
| orion5x_setup_dev1_win(RD88F5182_NOR_BASE, RD88F5182_NOR_SIZE); |
| platform_device_register(&rd88f5182_nor_flash); |
| |
| i2c_register_board_info(0, &rd88f5182_i2c_rtc, 1); |
| } |
| |
| MACHINE_START(RD88F5182, "Marvell Orion-NAS Reference Design") |
| /* Maintainer: Ronen Shitrit <rshitrit@marvell.com> */ |
| .phys_io = ORION5X_REGS_PHYS_BASE, |
| .io_pg_offst = ((ORION5X_REGS_VIRT_BASE) >> 18) & 0xFFFC, |
| .boot_params = 0x00000100, |
| .init_machine = rd88f5182_init, |
| .map_io = orion5x_map_io, |
| .init_irq = orion5x_init_irq, |
| .timer = &orion5x_timer, |
| MACHINE_END |