/*
 * Copyright (c) 2015-2019, The Linux Foundation. All rights reserved.
 *
 * This program is free software; you can redistribute it and/or modify
 * it under the terms of the GNU General Public License version 2 and
 * only version 2 as published by the Free Software Foundation.
 *
 * This program is distributed in the hope that it will be useful,
 * but WITHOUT ANY WARRANTY; without even the implied warranty of
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
 * GNU General Public License for more details.
 */

&cci {
	#address-cells = <1>;
	#size-cells = <0>;

	actuator0: qcom,actuator@0 {
		cell-index = <0>;
		reg = <0x0>;
		compatible = "qcom,actuator";
		qcom,cci-master = <0>;
//		cam_vaf-supply = <&pm8953_l17>;
		qcom,cam-vreg-name = "cam_vaf";
		qcom,cam-vreg-min-voltage = <2850000>;
		qcom,cam-vreg-max-voltage = <2850000>;
		qcom,cam-vreg-op-mode = <80000>;
	};

	actuator1: qcom,actuator@1 {
		cell-index = <1>;
		reg = <0x1>;
		compatible = "qcom,actuator";
		qcom,cci-master = <1>;
		cam_vaf-supply = <&pm8953_l17>;
		qcom,cam-vreg-name = "cam_vaf";
		qcom,cam-vreg-min-voltage = <2850000>;
		qcom,cam-vreg-max-voltage = <2850000>;
		qcom,cam-vreg-op-mode = <80000>;
	};

	eeprom0: qcom,eeprom@0 {
		cell-index = <0>;
		compatible = "qcom,eeprom";
		qcom,cci-master = <0>;
		reg = <0x0>;
		cam_vana-supply = <&pm8953_l22>;
		cam_v_custom1-supply = <&pm8953_l2>;
		qcom,cam-vreg-name = "cam_vana", "cam_v_custom1";
		qcom,cam-vreg-min-voltage = <2800000 1175000>;
		qcom,cam-vreg-max-voltage = <2800000 1175000>;
		qcom,cam-vreg-op-mode = <80000 105000>;
		pinctrl-names = "cam_default", "cam_suspend";
		pinctrl-0 = <&cam_sensor_mclk0_default &cam_sensor_rear_default>;
		pinctrl-1 = <&cam_sensor_mclk0_sleep &cam_sensor_rear_sleep>;
		gpios = <&tlmm 26 0>,
			<&tlmm 40 0>,
			<&tlmm 130 0>;
		qcom,gpio-reset = <1>;
		qcom,gpio-vio = <2>;
		qcom,gpio-req-tbl-num = <0 1 2>;
		qcom,gpio-req-tbl-flags = <1 0 0>;
		qcom,gpio-req-tbl-label = "CAMIF_MCLK0",
			"CAM_RESET0",
			"CAM_VIO";
		qcom,sensor-position = <0>;
		qcom,sensor-mode = <0>;
		status = "ok";
		clocks = <&clock_gcc clk_mclk0_clk_src>,
				<&clock_gcc clk_gcc_camss_mclk0_clk>;
		clock-names = "cam_src_clk", "cam_clk";
		qcom,clock-rates = <24000000 0>;
	};

/*<2018/10/18-Yuting Shih.[FAIRPHONE][MISC][COMMON][CAMERA][][]Modified for new front camera device driver S5K4H7YX. */
	eeprom1: qcom,eeprom@1 {
		cell-index = <1>;
		compatible = "qcom,eeprom";
		qcom,cci-master = <1>;
		reg = <0x1>;

#if 0
		qcom,eeprom-name = "samsung_s5k4h7yx";
		qcom,slave-addr = <0x20>;
		qcom,num-blocks = <2>;

		qcom,page0 = <1 0x0100 2 0x01 1 1>;
		qcom,poll0 = <0 0x0 2 0x0 1 0>;
		qcom,mem0 = <0 0x0 2 0x0 1 0>;
#endif

		/* cam_vio-supply = <&cam_vio_gpio_regulator>; */ /* IOVDD */
		cam_vana-supply = <&pm8953_l22>; /* AVDD */
		/* cam_vdig-supply = <&cam_front_dvdd_gpio_regulator>; */ /* DVDD */
		/* cam_vaf-supply = <&pm8953_l17>; */ /* AFVDD is not usage */
		qcom,cam-vreg-name = "cam_vana";  /* "cam_vio", "cam_vana", "cam_vdig"; */
		qcom,cam-vreg-min-voltage = <2800000>;
		qcom,cam-vreg-max-voltage = <2800000>;
		qcom,cam-vreg-op-mode = <80000>;
		qcom,gpio-no-mux = <0>;

		pinctrl-names = "cam_default", "cam_suspend";
		pinctrl-0 = <&cam_sensor_mclk1_default
				&cam_sensor_front1_default
				&cam_sensor_front1_vdig_default
				&cam_sensor_front1_vio_default>;
		pinctrl-1 = <&cam_sensor_mclk1_sleep
				&cam_sensor_front1_sleep
				&cam_sensor_front1_vdig_sleep
				&cam_sensor_front1_vio_sleep>;

/*<2018/11/14-Yuting Shih.[FAIRPHONE][MISC][COMMON][CAMERA][][]VOI control pin.PCBA EP0 is GPIO123;EP1 and above is GPIO130 */
		gpios = <&tlmm 27 0>,
				<&tlmm 129 0>,
				<&tlmm 46 0>,
#if 1
				<&tlmm 130 0>;
#else /* PCBA EP0 */
				<&tlmm 123 0>;
#endif
/*>2018/11/14-Yuting Shih.[FAIRPHONE][MISC][COMMON][CAMERA][][] */
		qcom,gpio-reset = <1>;
		qcom,gpio-vdig = <2>;
		qcom,gpio-vio = <3>;
		qcom,gpio-req-tbl-num = <0 1 2 3>;
		qcom,gpio-req-tbl-flags = <1 0 0 0>;
		qcom,gpio-req-tbl-label = "CAMIF_MCLK2",
				"CAM_RESET2",
				"CAM_VDIG2",
				"CAM_VIO2";

		status = "ok";
#if 1
		qcom,cam-power-seq-val = "sensor_gpio_reset",
				"cam_vana", "sensor_gpio_vdig",
				"sensor_gpio_vio", "sensor_gpio_reset",
				"sensor_cam_mclk";
		qcom,cam-power-seq-type = "sensor_gpio",
				"sensor_vreg", "sensor_gpio",
				"sensor_gpio", "sensor_gpio",
				"sensor_clk";
		qcom,cam-power-seq-cfg-val = <0 1 1 1 1 24000000>;
		qcom,cam-power-seq-delay = <5 1 1 3 3 10>; /* <1 1 1 1 1 10>; */
#endif
		clock-names = "cam_src_clk", "cam_clk";
		clocks = <&clock_gcc clk_mclk1_clk_src>,
				<&clock_gcc clk_gcc_camss_mclk1_clk>;
		qcom,clock-rates = <19200000 0>;
	};
/*>2018/10/18-Yuting Shih.[FAIRPHONE][MISC][COMMON][CAMERA][][]. */

	camera0: qcom,camera@0 {
		cell-index = <0>;
		compatible = "qcom,camera";
		reg = <0x0>;
		qcom,csiphy-sd-index = <0>;
		qcom,csid-sd-index = <0>;
		qcom,mount-angle = <270>;
		qcom,led-flash-src = <&led_flash0>;
		qcom,eeprom-src = <&eeprom0>;
		qcom,actuator-src = <&actuator0>;
//		cam_vio-supply = <&pm8953_l6>;
//		cam_vdig-supply = <&pm8953_l2>;
//		cam_vaf-supply = <&pm8953_l17>;
		cam_vana-supply = <&pm8953_l22>;
		cam_v_custom1-supply = <&pm8953_l2>;
		qcom,cam-vreg-name = "cam_vana", "cam_v_custom1";
		qcom,cam-vreg-min-voltage = <2800000 1175000>;
		qcom,cam-vreg-max-voltage = <2800000 1175000>;
		qcom,cam-vreg-op-mode = <80000 105000>;
		pinctrl-names = "cam_default", "cam_suspend";
		pinctrl-0 = <&cam_sensor_mclk0_default
				&cam_sensor_rear_default
				&cam_sensor_rear_vana>;
		pinctrl-1 = <&cam_sensor_mclk0_sleep &cam_sensor_rear_sleep
				&cam_sensor_rear_vana_sleep>;
		gpios = <&tlmm 26 0>,
			<&tlmm 40 0>,
			<&tlmm 130 0>,
			<&tlmm 128 0>;
		qcom,gpio-reset = <1>;
		qcom,gpio-vio = <2>;
		qcom,gpio-vaf = <3>;
		qcom,gpio-req-tbl-num = <0 1 2 3>;
		qcom,gpio-req-tbl-flags = <1 0 0 0>;
		qcom,gpio-req-tbl-label = "CAMIF_MCLK0",
			"CAM_RESET0",
			"CAM_VIO",
			"CAM_VAF";
		qcom,sensor-position = <0>;
		qcom,sensor-mode = <0>;
		qcom,cci-master = <0>;
		status = "ok";
		clocks = <&clock_gcc clk_mclk0_clk_src>,
				<&clock_gcc clk_gcc_camss_mclk0_clk>;
		clock-names = "cam_src_clk", "cam_clk";
		qcom,clock-rates = <24000000 0>;
	};

/*<2018/10/18-Yuting Shih.[FAIRPHONE][MISC][COMMON][CAMERA][][]Modified for new front camera device driver S5K4H7YX. */
	camera2: qcom,camera@2 {
		cell-index = <2>;
		compatible = "qcom,camera";
		reg = <0x02>;
		qcom,csiphy-sd-index = <2>;
		qcom,csid-sd-index = <1>; /* SDM450 support 2 CSID cores. MSM8953 is 3 CSID cores */
		qcom,mount-angle = <270>; /* <90>; */
		qcom,eeprom-src = <&eeprom1>;
		/* qcom,actuator-src = <&actuator1>; */ /* The auto focus is not support */

		/* cam_vio-supply = <&cam_vio_gpio_regulator>; */
		cam_vana-supply = <&pm8953_l22>;
		/* cam_vdig-supply = <&cam_front_dvdd_gpio_regulator>; */
		/* cam_vaf-supply = <&pm8953_l17>; */ /* The AFVDD is not support */
		qcom,cam-vreg-name = "cam_vana";
		qcom,cam-vreg-min-voltage = <2800000>;
		qcom,cam-vreg-max-voltage = <2800000>;
		qcom,cam-vreg-op-mode = <80000>;
		qcom,gpio-no-mux = <0>;

		pinctrl-names = "cam_default", "cam_suspend";
		pinctrl-0 = <&cam_sensor_mclk1_default
				&cam_sensor_front1_default
				&cam_sensor_front1_vdig_default
				&cam_sensor_front1_vio_default>;
		pinctrl-1 = <&cam_sensor_mclk1_sleep
				&cam_sensor_front1_sleep
				&cam_sensor_front1_vdig_sleep
				&cam_sensor_front1_vio_sleep>;

/*<2018/11/14-Yuting Shih.[FAIRPHONE][MISC][COMMON][CAMERA][][]VOI control pin.PCBA EP0 is GPIO123;EP1 and above is GPIO130 */
		gpios = <&tlmm 27 0>,
				<&tlmm 129 0>,
				<&tlmm 46 0>,
#if 1
				<&tlmm 130 0>;
#else /* PCBA EP0 */
				<&tlmm 123 0>;
#endif
/*>2018/11/14-Yuting Shih.[FAIRPHONE][MISC][COMMON][CAMERA][][] */
		qcom,gpio-reset = <1>;
		qcom,gpio-vdig = <2>;
		qcom,gpio-vio = <3>;
		qcom,gpio-req-tbl-num = <0 1 2 3>;
		qcom,gpio-req-tbl-flags = <1 0 0 0>;
		qcom,gpio-req-tbl-label = "CAMIF_MCLK2",
				"CAM_RESET2",
				"CAM_VDIG2",
				"CAM_VIO2";

		qcom,sensor-position = <1>;
		qcom,sensor-mode = <0>;
		qcom,cci-master = <1>;
		status = "ok";
		clock-names = "cam_src_clk", "cam_clk";
		clocks = <&clock_gcc clk_mclk1_clk_src>,
				<&clock_gcc clk_gcc_camss_mclk1_clk>;
		qcom,clock-rates = <24000000 0>;
	};
/*>2018/10/18-Yuting Shih.[FAIRPHONE][MISC][COMMON][CAMERA][][]. */
};