mtd: nand: fsmc: get rid of the fsmc_nand_eccplace struct
Now that mtd_ooblayout_ecc() returns the ECC byte position using the
OOB free method, we can get rid of the fsmc_nand_eccplace struct.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
diff --git a/drivers/mtd/nand/fsmc_nand.c b/drivers/mtd/nand/fsmc_nand.c
index 275a98c..1372040 100644
--- a/drivers/mtd/nand/fsmc_nand.c
+++ b/drivers/mtd/nand/fsmc_nand.c
@@ -39,35 +39,6 @@
#include <linux/amba/bus.h>
#include <mtd/mtd-abi.h>
-/*
- * ECC placement definitions in oobfree type format.
- * There are 13 bytes of ecc for every 512 byte block and it has to be read
- * consecutively and immediately after the 512 byte data block for hardware to
- * generate the error bit offsets in 512 byte data.
- * Managing the ecc bytes in the following way makes it easier for software to
- * read ecc bytes consecutive to data bytes. This way is similar to
- * oobfree structure maintained already in generic nand driver
- */
-static struct fsmc_eccplace fsmc_ecc4_lp_place = {
- .eccplace = {
- {.offset = 2, .length = 13},
- {.offset = 18, .length = 13},
- {.offset = 34, .length = 13},
- {.offset = 50, .length = 13},
- {.offset = 66, .length = 13},
- {.offset = 82, .length = 13},
- {.offset = 98, .length = 13},
- {.offset = 114, .length = 13}
- }
-};
-
-static struct fsmc_eccplace fsmc_ecc4_sp_place = {
- .eccplace = {
- {.offset = 0, .length = 4},
- {.offset = 6, .length = 9}
- }
-};
-
static int fsmc_ecc1_ooblayout_ecc(struct mtd_info *mtd, int section,
struct mtd_oob_region *oobregion)
{
@@ -105,6 +76,12 @@
.free = fsmc_ecc1_ooblayout_free,
};
+/*
+ * ECC placement definitions in oobfree type format.
+ * There are 13 bytes of ecc for every 512 byte block and it has to be read
+ * consecutively and immediately after the 512 byte data block for hardware to
+ * generate the error bit offsets in 512 byte data.
+ */
static int fsmc_ecc4_ooblayout_ecc(struct mtd_info *mtd, int section,
struct mtd_oob_region *oobregion)
{
@@ -155,7 +132,6 @@
* @partitions: Partition info for a NAND Flash.
* @nr_partitions: Total number of partition of a NAND flash.
*
- * @ecc_place: ECC placing locations in oobfree type format.
* @bank: Bank number for probed device.
* @clk: Clock structure for FSMC.
*
@@ -175,7 +151,6 @@
struct mtd_partition *partitions;
unsigned int nr_partitions;
- struct fsmc_eccplace *ecc_place;
unsigned int bank;
struct device *dev;
enum access_mode mode;
@@ -582,8 +557,6 @@
static int fsmc_read_page_hwecc(struct mtd_info *mtd, struct nand_chip *chip,
uint8_t *buf, int oob_required, int page)
{
- struct fsmc_nand_data *host = mtd_to_fsmc(mtd);
- struct fsmc_eccplace *ecc_place = host->ecc_place;
int i, j, s, stat, eccsize = chip->ecc.size;
int eccbytes = chip->ecc.bytes;
int eccsteps = chip->ecc.steps;
@@ -606,9 +579,15 @@
chip->read_buf(mtd, p, eccsize);
for (j = 0; j < eccbytes;) {
- off = ecc_place->eccplace[group].offset;
- len = ecc_place->eccplace[group].length;
- group++;
+ struct mtd_oob_region oobregion;
+ int ret;
+
+ ret = mtd_ooblayout_ecc(mtd, group++, &oobregion);
+ if (ret)
+ return ret;
+
+ off = oobregion.offset;
+ len = oobregion.length;
/*
* length is intentionally kept a higher multiple of 2
@@ -956,19 +935,10 @@
if (AMBA_REV_BITS(host->pid) >= 8) {
switch (mtd->oobsize) {
case 16:
- host->ecc_place = &fsmc_ecc4_sp_place;
- break;
case 64:
- host->ecc_place = &fsmc_ecc4_lp_place;
- break;
case 128:
- host->ecc_place = &fsmc_ecc4_lp_place;
- break;
case 224:
- host->ecc_place = &fsmc_ecc4_lp_place;
- break;
case 256:
- host->ecc_place = &fsmc_ecc4_lp_place;
break;
default:
dev_warn(&pdev->dev, "No oob scheme defined for oobsize %d\n",
diff --git a/include/linux/mtd/fsmc.h b/include/linux/mtd/fsmc.h
index c8be32e..ad3c348 100644
--- a/include/linux/mtd/fsmc.h
+++ b/include/linux/mtd/fsmc.h
@@ -103,24 +103,6 @@
#define FSMC_BUSY_WAIT_TIMEOUT (1 * HZ)
-/*
- * There are 13 bytes of ecc for every 512 byte block in FSMC version 8
- * and it has to be read consecutively and immediately after the 512
- * byte data block for hardware to generate the error bit offsets
- * Managing the ecc bytes in the following way is easier. This way is
- * similar to oobfree structure maintained already in u-boot nand driver
- */
-#define MAX_ECCPLACE_ENTRIES 32
-
-struct fsmc_nand_eccplace {
- uint8_t offset;
- uint8_t length;
-};
-
-struct fsmc_eccplace {
- struct fsmc_nand_eccplace eccplace[MAX_ECCPLACE_ENTRIES];
-};
-
struct fsmc_nand_timings {
uint8_t tclr;
uint8_t tar;