arch/arm/mach-omap2/control.c - kernel/msm-4.9 - Gitiles

 /*
  * OMAP2/3 System Control Module register access
  *
  * Copyright (C) 2007, 2012 Texas Instruments, Inc.
  * Copyright (C) 2007 Nokia Corporation
  *
  * Written by Paul Walmsley
  *
  * This program is free software; you can redistribute it and/or modify
  * it under the terms of the GNU General Public License version 2 as
  * published by the Free Software Foundation.
  */
 #undef DEBUG

 #include <linux/kernel.h>
 #include <linux/io.h>

 #include "soc.h"
 #include "iomap.h"
 #include "common.h"
 #include "cm-regbits-34xx.h"
 #include "prm-regbits-34xx.h"
 #include "prm3xxx.h"
 #include "cm3xxx.h"
 #include "sdrc.h"
 #include "pm.h"
 #include "control.h"

 /* Used by omap3_ctrl_save_padconf() */
 #define START_PADCONF_SAVE		0x2
 #define PADCONF_SAVE_DONE		0x1

 static void __iomem *omap2_ctrl_base;
 static void __iomem *omap4_ctrl_pad_base;

 #if defined(CONFIG_ARCH_OMAP3) && defined(CONFIG_PM)
 struct omap3_scratchpad {
 	u32 boot_config_ptr;
 	u32 public_restore_ptr;
 	u32 secure_ram_restore_ptr;
 	u32 sdrc_module_semaphore;
 	u32 prcm_block_offset;
 	u32 sdrc_block_offset;
 };

 struct omap3_scratchpad_prcm_block {
 	u32 prm_clksrc_ctrl;
 	u32 prm_clksel;
 	u32 cm_contents[11];
 	u32 prcm_block_size;
 };

 struct omap3_scratchpad_sdrc_block {
 	u16 sysconfig;
 	u16 cs_cfg;
 	u16 sharing;
 	u16 err_type;
 	u32 dll_a_ctrl;
 	u32 dll_b_ctrl;
 	u32 power;
 	u32 cs_0;
 	u32 mcfg_0;
 	u16 mr_0;
 	u16 emr_1_0;
 	u16 emr_2_0;
 	u16 emr_3_0;
 	u32 actim_ctrla_0;
 	u32 actim_ctrlb_0;
 	u32 rfr_ctrl_0;
 	u32 cs_1;
 	u32 mcfg_1;
 	u16 mr_1;
 	u16 emr_1_1;
 	u16 emr_2_1;
 	u16 emr_3_1;
 	u32 actim_ctrla_1;
 	u32 actim_ctrlb_1;
 	u32 rfr_ctrl_1;
 	u16 dcdl_1_ctrl;
 	u16 dcdl_2_ctrl;
 	u32 flags;
 	u32 block_size;
 };

 void *omap3_secure_ram_storage;

 /*
  * This is used to store ARM registers in SDRAM before attempting
  * an MPU OFF. The save and restore happens from the SRAM sleep code.
  * The address is stored in scratchpad, so that it can be used
  * during the restore path.
  */
 u32 omap3_arm_context[128];

 struct omap3_control_regs {
 	u32 sysconfig;
 	u32 devconf0;
 	u32 mem_dftrw0;
 	u32 mem_dftrw1;
 	u32 msuspendmux_0;
 	u32 msuspendmux_1;
 	u32 msuspendmux_2;
 	u32 msuspendmux_3;
 	u32 msuspendmux_4;
 	u32 msuspendmux_5;
 	u32 sec_ctrl;
 	u32 devconf1;
 	u32 csirxfe;
 	u32 iva2_bootaddr;
 	u32 iva2_bootmod;
 	u32 debobs_0;
 	u32 debobs_1;
 	u32 debobs_2;
 	u32 debobs_3;
 	u32 debobs_4;
 	u32 debobs_5;
 	u32 debobs_6;
 	u32 debobs_7;
 	u32 debobs_8;
 	u32 prog_io0;
 	u32 prog_io1;
 	u32 dss_dpll_spreading;
 	u32 core_dpll_spreading;
 	u32 per_dpll_spreading;
 	u32 usbhost_dpll_spreading;
 	u32 pbias_lite;
 	u32 temp_sensor;
 	u32 sramldo4;
 	u32 sramldo5;
 	u32 csi;
 	u32 padconf_sys_nirq;
 };

 static struct omap3_control_regs control_context;
 #endif /* CONFIG_ARCH_OMAP3 && CONFIG_PM */

 #define OMAP_CTRL_REGADDR(reg)		(omap2_ctrl_base + (reg))
 #define OMAP4_CTRL_PAD_REGADDR(reg)	(omap4_ctrl_pad_base + (reg))

 void __init omap2_set_globals_control(void __iomem *ctrl,
 				      void __iomem *ctrl_pad)
 {
 	omap2_ctrl_base = ctrl;
 	omap4_ctrl_pad_base = ctrl_pad;
 }

 void __iomem *omap_ctrl_base_get(void)
 {
 	return omap2_ctrl_base;
 }

 u8 omap_ctrl_readb(u16 offset)
 {
 	return readb_relaxed(OMAP_CTRL_REGADDR(offset));
 }

 u16 omap_ctrl_readw(u16 offset)
 {
 	return readw_relaxed(OMAP_CTRL_REGADDR(offset));
 }

 u32 omap_ctrl_readl(u16 offset)
 {
 	return readl_relaxed(OMAP_CTRL_REGADDR(offset));
 }

 void omap_ctrl_writeb(u8 val, u16 offset)
 {
 	writeb_relaxed(val, OMAP_CTRL_REGADDR(offset));
 }

 void omap_ctrl_writew(u16 val, u16 offset)
 {
 	writew_relaxed(val, OMAP_CTRL_REGADDR(offset));
 }

 void omap_ctrl_writel(u32 val, u16 offset)
 {
 	writel_relaxed(val, OMAP_CTRL_REGADDR(offset));
 }

 /*
  * On OMAP4 control pad are not addressable from control
  * core base. So the common omap_ctrl_read/write APIs breaks
  * Hence export separate APIs to manage the omap4 pad control
  * registers. This APIs will work only for OMAP4
  */

 u32 omap4_ctrl_pad_readl(u16 offset)
 {
 	return readl_relaxed(OMAP4_CTRL_PAD_REGADDR(offset));
 }

 void omap4_ctrl_pad_writel(u32 val, u16 offset)
 {
 	writel_relaxed(val, OMAP4_CTRL_PAD_REGADDR(offset));
 }

 #ifdef CONFIG_ARCH_OMAP3

 /**
  * omap3_ctrl_write_boot_mode - set scratchpad boot mode for the next boot
  * @bootmode: 8-bit value to pass to some boot code
  *
  * Set the bootmode in the scratchpad RAM.  This is used after the
  * system restarts.  Not sure what actually uses this - it may be the
  * bootloader, rather than the boot ROM - contrary to the preserved
  * comment below.  No return value.
  */
 void omap3_ctrl_write_boot_mode(u8 bootmode)
 {
 	u32 l;

 	l = ('B' << 24) | ('M' << 16) | bootmode;

 	/*
 	 * Reserve the first word in scratchpad for communicating
 	 * with the boot ROM. A pointer to a data structure
 	 * describing the boot process can be stored there,
 	 * cf. OMAP34xx TRM, Initialization / Software Booting
 	 * Configuration.
 	 *
 	 * XXX This should use some omap_ctrl_writel()-type function
 	 */
 	writel_relaxed(l, OMAP2_L4_IO_ADDRESS(OMAP343X_SCRATCHPAD + 4));
 }

 #endif

 /**
  * omap_ctrl_write_dsp_boot_addr - set boot address for a remote processor
  * @bootaddr: physical address of the boot loader
  *
  * Set boot address for the boot loader of a supported processor
  * when a power ON sequence occurs.
  */
 void omap_ctrl_write_dsp_boot_addr(u32 bootaddr)
 {
 	u32 offset = cpu_is_omap243x() ? OMAP243X_CONTROL_IVA2_BOOTADDR :
 		     cpu_is_omap34xx() ? OMAP343X_CONTROL_IVA2_BOOTADDR :
 		     cpu_is_omap44xx() ? OMAP4_CTRL_MODULE_CORE_DSP_BOOTADDR :
 		     soc_is_omap54xx() ? OMAP4_CTRL_MODULE_CORE_DSP_BOOTADDR :
 		     0;

 	if (!offset) {
 		pr_err("%s: unsupported omap type\n", __func__);
 		return;
 	}

 	omap_ctrl_writel(bootaddr, offset);
 }

 /**
  * omap_ctrl_write_dsp_boot_mode - set boot mode for a remote processor
  * @bootmode: 8-bit value to pass to some boot code
  *
  * Sets boot mode for the boot loader of a supported processor
  * when a power ON sequence occurs.
  */
 void omap_ctrl_write_dsp_boot_mode(u8 bootmode)
 {
 	u32 offset = cpu_is_omap243x() ? OMAP243X_CONTROL_IVA2_BOOTMOD :
 		     cpu_is_omap34xx() ? OMAP343X_CONTROL_IVA2_BOOTMOD :
 		     0;

 	if (!offset) {
 		pr_err("%s: unsupported omap type\n", __func__);
 		return;
 	}

 	omap_ctrl_writel(bootmode, offset);
 }

 #if defined(CONFIG_ARCH_OMAP3) && defined(CONFIG_PM)
 /*
  * Clears the scratchpad contents in case of cold boot-
  * called during bootup
  */
 void omap3_clear_scratchpad_contents(void)
 {
 	u32 max_offset = OMAP343X_SCRATCHPAD_ROM_OFFSET;
 	void __iomem *v_addr;
 	u32 offset = 0;
 	v_addr = OMAP2_L4_IO_ADDRESS(OMAP343X_SCRATCHPAD_ROM);
 	if (omap2_prm_read_mod_reg(OMAP3430_GR_MOD, OMAP3_PRM_RSTST_OFFSET) &
 	    OMAP3430_GLOBAL_COLD_RST_MASK) {
 		for ( ; offset <= max_offset; offset += 0x4)
 			writel_relaxed(0x0, (v_addr + offset));
 		omap2_prm_set_mod_reg_bits(OMAP3430_GLOBAL_COLD_RST_MASK,
 					   OMAP3430_GR_MOD,
 					   OMAP3_PRM_RSTST_OFFSET);
 	}
 }

 /* Populate the scratchpad structure with restore structure */
 void omap3_save_scratchpad_contents(void)
 {
 	void  __iomem *scratchpad_address;
 	u32 arm_context_addr;
 	struct omap3_scratchpad scratchpad_contents;
 	struct omap3_scratchpad_prcm_block prcm_block_contents;
 	struct omap3_scratchpad_sdrc_block sdrc_block_contents;

 	/*
 	 * Populate the Scratchpad contents
 	 *
 	 * The "get_*restore_pointer" functions are used to provide a
 	 * physical restore address where the ROM code jumps while waking
 	 * up from MPU OFF/OSWR state.
 	 * The restore pointer is stored into the scratchpad.
 	 */
 	scratchpad_contents.boot_config_ptr = 0x0;
 	if (cpu_is_omap3630())
 		scratchpad_contents.public_restore_ptr =
 			virt_to_phys(omap3_restore_3630);
 	else if (omap_rev() != OMAP3430_REV_ES3_0 &&
 					omap_rev() != OMAP3430_REV_ES3_1)
 		scratchpad_contents.public_restore_ptr =
 			virt_to_phys(omap3_restore);
 	else
 		scratchpad_contents.public_restore_ptr =
 			virt_to_phys(omap3_restore_es3);

 	if (omap_type() == OMAP2_DEVICE_TYPE_GP)
 		scratchpad_contents.secure_ram_restore_ptr = 0x0;
 	else
 		scratchpad_contents.secure_ram_restore_ptr =
 			(u32) __pa(omap3_secure_ram_storage);
 	scratchpad_contents.sdrc_module_semaphore = 0x0;
 	scratchpad_contents.prcm_block_offset = 0x2C;
 	scratchpad_contents.sdrc_block_offset = 0x64;

 	/* Populate the PRCM block contents */
 	prcm_block_contents.prm_clksrc_ctrl =
 		omap2_prm_read_mod_reg(OMAP3430_GR_MOD,
 				       OMAP3_PRM_CLKSRC_CTRL_OFFSET);
 	prcm_block_contents.prm_clksel =
 		omap2_prm_read_mod_reg(OMAP3430_CCR_MOD,
 				       OMAP3_PRM_CLKSEL_OFFSET);

 	omap3_cm_save_scratchpad_contents(prcm_block_contents.cm_contents);

 	prcm_block_contents.prcm_block_size = 0x0;

 	/* Populate the SDRC block contents */
 	sdrc_block_contents.sysconfig =
 			(sdrc_read_reg(SDRC_SYSCONFIG) & 0xFFFF);
 	sdrc_block_contents.cs_cfg =
 			(sdrc_read_reg(SDRC_CS_CFG) & 0xFFFF);
 	sdrc_block_contents.sharing =
 			(sdrc_read_reg(SDRC_SHARING) & 0xFFFF);
 	sdrc_block_contents.err_type =
 			(sdrc_read_reg(SDRC_ERR_TYPE) & 0xFFFF);
 	sdrc_block_contents.dll_a_ctrl = sdrc_read_reg(SDRC_DLLA_CTRL);
 	sdrc_block_contents.dll_b_ctrl = 0x0;
 	/*
 	 * Due to a OMAP3 errata (1.142), on EMU/HS devices SRDC should
 	 * be programed to issue automatic self refresh on timeout
 	 * of AUTO_CNT = 1 prior to any transition to OFF mode.
 	 */
 	if ((omap_type() != OMAP2_DEVICE_TYPE_GP)
 			&& (omap_rev() >= OMAP3430_REV_ES3_0))
 		sdrc_block_contents.power = (sdrc_read_reg(SDRC_POWER) &
 				~(SDRC_POWER_AUTOCOUNT_MASK|
 				SDRC_POWER_CLKCTRL_MASK)) |
 				(1 << SDRC_POWER_AUTOCOUNT_SHIFT) |
 				SDRC_SELF_REFRESH_ON_AUTOCOUNT;
 	else
 		sdrc_block_contents.power = sdrc_read_reg(SDRC_POWER);

 	sdrc_block_contents.cs_0 = 0x0;
 	sdrc_block_contents.mcfg_0 = sdrc_read_reg(SDRC_MCFG_0);
 	sdrc_block_contents.mr_0 = (sdrc_read_reg(SDRC_MR_0) & 0xFFFF);
 	sdrc_block_contents.emr_1_0 = 0x0;
 	sdrc_block_contents.emr_2_0 = 0x0;
 	sdrc_block_contents.emr_3_0 = 0x0;
 	sdrc_block_contents.actim_ctrla_0 =
 			sdrc_read_reg(SDRC_ACTIM_CTRL_A_0);
 	sdrc_block_contents.actim_ctrlb_0 =
 			sdrc_read_reg(SDRC_ACTIM_CTRL_B_0);
 	sdrc_block_contents.rfr_ctrl_0 =
 			sdrc_read_reg(SDRC_RFR_CTRL_0);
 	sdrc_block_contents.cs_1 = 0x0;
 	sdrc_block_contents.mcfg_1 = sdrc_read_reg(SDRC_MCFG_1);
 	sdrc_block_contents.mr_1 = sdrc_read_reg(SDRC_MR_1) & 0xFFFF;
 	sdrc_block_contents.emr_1_1 = 0x0;
 	sdrc_block_contents.emr_2_1 = 0x0;
 	sdrc_block_contents.emr_3_1 = 0x0;
 	sdrc_block_contents.actim_ctrla_1 =
 			sdrc_read_reg(SDRC_ACTIM_CTRL_A_1);
 	sdrc_block_contents.actim_ctrlb_1 =
 			sdrc_read_reg(SDRC_ACTIM_CTRL_B_1);
 	sdrc_block_contents.rfr_ctrl_1 =
 			sdrc_read_reg(SDRC_RFR_CTRL_1);
 	sdrc_block_contents.dcdl_1_ctrl = 0x0;
 	sdrc_block_contents.dcdl_2_ctrl = 0x0;
 	sdrc_block_contents.flags = 0x0;
 	sdrc_block_contents.block_size = 0x0;

 	arm_context_addr = virt_to_phys(omap3_arm_context);

 	/* Copy all the contents to the scratchpad location */
 	scratchpad_address = OMAP2_L4_IO_ADDRESS(OMAP343X_SCRATCHPAD);
 	memcpy_toio(scratchpad_address, &scratchpad_contents,
 		 sizeof(scratchpad_contents));
 	/* Scratchpad contents being 32 bits, a divide by 4 done here */
 	memcpy_toio(scratchpad_address +
 		scratchpad_contents.prcm_block_offset,
 		&prcm_block_contents, sizeof(prcm_block_contents));
 	memcpy_toio(scratchpad_address +
 		scratchpad_contents.sdrc_block_offset,
 		&sdrc_block_contents, sizeof(sdrc_block_contents));
 	/*
 	 * Copies the address of the location in SDRAM where ARM
 	 * registers get saved during a MPU OFF transition.
 	 */
 	memcpy_toio(scratchpad_address +
 		scratchpad_contents.sdrc_block_offset +
 		sizeof(sdrc_block_contents), &arm_context_addr, 4);
 }

 void omap3_control_save_context(void)
 {
 	control_context.sysconfig = omap_ctrl_readl(OMAP2_CONTROL_SYSCONFIG);
 	control_context.devconf0 = omap_ctrl_readl(OMAP2_CONTROL_DEVCONF0);
 	control_context.mem_dftrw0 =
 			omap_ctrl_readl(OMAP343X_CONTROL_MEM_DFTRW0);
 	control_context.mem_dftrw1 =
 			omap_ctrl_readl(OMAP343X_CONTROL_MEM_DFTRW1);
 	control_context.msuspendmux_0 =
 			omap_ctrl_readl(OMAP2_CONTROL_MSUSPENDMUX_0);
 	control_context.msuspendmux_1 =
 			omap_ctrl_readl(OMAP2_CONTROL_MSUSPENDMUX_1);
 	control_context.msuspendmux_2 =
 			omap_ctrl_readl(OMAP2_CONTROL_MSUSPENDMUX_2);
 	control_context.msuspendmux_3 =
 			omap_ctrl_readl(OMAP2_CONTROL_MSUSPENDMUX_3);
 	control_context.msuspendmux_4 =
 			omap_ctrl_readl(OMAP2_CONTROL_MSUSPENDMUX_4);
 	control_context.msuspendmux_5 =
 			omap_ctrl_readl(OMAP2_CONTROL_MSUSPENDMUX_5);
 	control_context.sec_ctrl = omap_ctrl_readl(OMAP2_CONTROL_SEC_CTRL);
 	control_context.devconf1 = omap_ctrl_readl(OMAP343X_CONTROL_DEVCONF1);
 	control_context.csirxfe = omap_ctrl_readl(OMAP343X_CONTROL_CSIRXFE);
 	control_context.iva2_bootaddr =
 			omap_ctrl_readl(OMAP343X_CONTROL_IVA2_BOOTADDR);
 	control_context.iva2_bootmod =
 			omap_ctrl_readl(OMAP343X_CONTROL_IVA2_BOOTMOD);
 	control_context.debobs_0 = omap_ctrl_readl(OMAP343X_CONTROL_DEBOBS(0));
 	control_context.debobs_1 = omap_ctrl_readl(OMAP343X_CONTROL_DEBOBS(1));
 	control_context.debobs_2 = omap_ctrl_readl(OMAP343X_CONTROL_DEBOBS(2));
 	control_context.debobs_3 = omap_ctrl_readl(OMAP343X_CONTROL_DEBOBS(3));
 	control_context.debobs_4 = omap_ctrl_readl(OMAP343X_CONTROL_DEBOBS(4));
 	control_context.debobs_5 = omap_ctrl_readl(OMAP343X_CONTROL_DEBOBS(5));
 	control_context.debobs_6 = omap_ctrl_readl(OMAP343X_CONTROL_DEBOBS(6));
 	control_context.debobs_7 = omap_ctrl_readl(OMAP343X_CONTROL_DEBOBS(7));
 	control_context.debobs_8 = omap_ctrl_readl(OMAP343X_CONTROL_DEBOBS(8));
 	control_context.prog_io0 = omap_ctrl_readl(OMAP343X_CONTROL_PROG_IO0);
 	control_context.prog_io1 = omap_ctrl_readl(OMAP343X_CONTROL_PROG_IO1);
 	control_context.dss_dpll_spreading =
 			omap_ctrl_readl(OMAP343X_CONTROL_DSS_DPLL_SPREADING);
 	control_context.core_dpll_spreading =
 			omap_ctrl_readl(OMAP343X_CONTROL_CORE_DPLL_SPREADING);
 	control_context.per_dpll_spreading =
 			omap_ctrl_readl(OMAP343X_CONTROL_PER_DPLL_SPREADING);
 	control_context.usbhost_dpll_spreading =
 		omap_ctrl_readl(OMAP343X_CONTROL_USBHOST_DPLL_SPREADING);
 	control_context.pbias_lite =
 			omap_ctrl_readl(OMAP343X_CONTROL_PBIAS_LITE);
 	control_context.temp_sensor =
 			omap_ctrl_readl(OMAP343X_CONTROL_TEMP_SENSOR);
 	control_context.sramldo4 = omap_ctrl_readl(OMAP343X_CONTROL_SRAMLDO4);
 	control_context.sramldo5 = omap_ctrl_readl(OMAP343X_CONTROL_SRAMLDO5);
 	control_context.csi = omap_ctrl_readl(OMAP343X_CONTROL_CSI);
 	control_context.padconf_sys_nirq =
 		omap_ctrl_readl(OMAP343X_CONTROL_PADCONF_SYSNIRQ);
 	return;
 }

 void omap3_control_restore_context(void)
 {
 	omap_ctrl_writel(control_context.sysconfig, OMAP2_CONTROL_SYSCONFIG);
 	omap_ctrl_writel(control_context.devconf0, OMAP2_CONTROL_DEVCONF0);
 	omap_ctrl_writel(control_context.mem_dftrw0,
 					OMAP343X_CONTROL_MEM_DFTRW0);
 	omap_ctrl_writel(control_context.mem_dftrw1,
 					OMAP343X_CONTROL_MEM_DFTRW1);
 	omap_ctrl_writel(control_context.msuspendmux_0,
 					OMAP2_CONTROL_MSUSPENDMUX_0);
 	omap_ctrl_writel(control_context.msuspendmux_1,
 					OMAP2_CONTROL_MSUSPENDMUX_1);
 	omap_ctrl_writel(control_context.msuspendmux_2,
 					OMAP2_CONTROL_MSUSPENDMUX_2);
 	omap_ctrl_writel(control_context.msuspendmux_3,
 					OMAP2_CONTROL_MSUSPENDMUX_3);
 	omap_ctrl_writel(control_context.msuspendmux_4,
 					OMAP2_CONTROL_MSUSPENDMUX_4);
 	omap_ctrl_writel(control_context.msuspendmux_5,
 					OMAP2_CONTROL_MSUSPENDMUX_5);
 	omap_ctrl_writel(control_context.sec_ctrl, OMAP2_CONTROL_SEC_CTRL);
 	omap_ctrl_writel(control_context.devconf1, OMAP343X_CONTROL_DEVCONF1);
 	omap_ctrl_writel(control_context.csirxfe, OMAP343X_CONTROL_CSIRXFE);
 	omap_ctrl_writel(control_context.iva2_bootaddr,
 					OMAP343X_CONTROL_IVA2_BOOTADDR);
 	omap_ctrl_writel(control_context.iva2_bootmod,
 					OMAP343X_CONTROL_IVA2_BOOTMOD);
 	omap_ctrl_writel(control_context.debobs_0, OMAP343X_CONTROL_DEBOBS(0));
 	omap_ctrl_writel(control_context.debobs_1, OMAP343X_CONTROL_DEBOBS(1));
 	omap_ctrl_writel(control_context.debobs_2, OMAP343X_CONTROL_DEBOBS(2));
 	omap_ctrl_writel(control_context.debobs_3, OMAP343X_CONTROL_DEBOBS(3));
 	omap_ctrl_writel(control_context.debobs_4, OMAP343X_CONTROL_DEBOBS(4));
 	omap_ctrl_writel(control_context.debobs_5, OMAP343X_CONTROL_DEBOBS(5));
 	omap_ctrl_writel(control_context.debobs_6, OMAP343X_CONTROL_DEBOBS(6));
 	omap_ctrl_writel(control_context.debobs_7, OMAP343X_CONTROL_DEBOBS(7));
 	omap_ctrl_writel(control_context.debobs_8, OMAP343X_CONTROL_DEBOBS(8));
 	omap_ctrl_writel(control_context.prog_io0, OMAP343X_CONTROL_PROG_IO0);
 	omap_ctrl_writel(control_context.prog_io1, OMAP343X_CONTROL_PROG_IO1);
 	omap_ctrl_writel(control_context.dss_dpll_spreading,
 					OMAP343X_CONTROL_DSS_DPLL_SPREADING);
 	omap_ctrl_writel(control_context.core_dpll_spreading,
 					OMAP343X_CONTROL_CORE_DPLL_SPREADING);
 	omap_ctrl_writel(control_context.per_dpll_spreading,
 					OMAP343X_CONTROL_PER_DPLL_SPREADING);
 	omap_ctrl_writel(control_context.usbhost_dpll_spreading,
 				OMAP343X_CONTROL_USBHOST_DPLL_SPREADING);
 	omap_ctrl_writel(control_context.pbias_lite,
 					OMAP343X_CONTROL_PBIAS_LITE);
 	omap_ctrl_writel(control_context.temp_sensor,
 					OMAP343X_CONTROL_TEMP_SENSOR);
 	omap_ctrl_writel(control_context.sramldo4, OMAP343X_CONTROL_SRAMLDO4);
 	omap_ctrl_writel(control_context.sramldo5, OMAP343X_CONTROL_SRAMLDO5);
 	omap_ctrl_writel(control_context.csi, OMAP343X_CONTROL_CSI);
 	omap_ctrl_writel(control_context.padconf_sys_nirq,
 			 OMAP343X_CONTROL_PADCONF_SYSNIRQ);
 	return;
 }

 void omap3630_ctrl_disable_rta(void)
 {
 	if (!cpu_is_omap3630())
 		return;
 	omap_ctrl_writel(OMAP36XX_RTA_DISABLE, OMAP36XX_CONTROL_MEM_RTA_CTRL);
 }

 /**
  * omap3_ctrl_save_padconf - save padconf registers to scratchpad RAM
  *
  * Tell the SCM to start saving the padconf registers, then wait for
  * the process to complete.  Returns 0 unconditionally, although it
  * should also eventually be able to return -ETIMEDOUT, if the save
  * does not complete.
  *
  * XXX This function is missing a timeout.  What should it be?
  */
 int omap3_ctrl_save_padconf(void)
 {
 	u32 cpo;

 	/* Save the padconf registers */
 	cpo = omap_ctrl_readl(OMAP343X_CONTROL_PADCONF_OFF);
 	cpo |= START_PADCONF_SAVE;
 	omap_ctrl_writel(cpo, OMAP343X_CONTROL_PADCONF_OFF);

 	/* wait for the save to complete */
 	while (!(omap_ctrl_readl(OMAP343X_CONTROL_GENERAL_PURPOSE_STATUS)
 		 & PADCONF_SAVE_DONE))
 		udelay(1);

 	return 0;
 }

 /**
  * omap3_ctrl_set_iva_bootmode_idle - sets the IVA2 bootmode to idle
  *
  * Sets the bootmode for IVA2 to idle. This is needed by the PM code to
  * force disable IVA2 so that it does not prevent any low-power states.
  */
 void omap3_ctrl_set_iva_bootmode_idle(void)
 {
 	omap_ctrl_writel(OMAP3_IVA2_BOOTMOD_IDLE,
 			 OMAP343X_CONTROL_IVA2_BOOTMOD);
 }
 #endif /* CONFIG_ARCH_OMAP3 && CONFIG_PM */
	/*
	* OMAP2/3 System Control Module register access
	*
	* Copyright (C) 2007, 2012 Texas Instruments, Inc.
	* Copyright (C) 2007 Nokia Corporation
	*
	* Written by Paul Walmsley
	*
	* This program is free software; you can redistribute it and/or modify
	* it under the terms of the GNU General Public License version 2 as
	* published by the Free Software Foundation.
	*/
	#undef DEBUG

	#include <linux/kernel.h>
	#include <linux/io.h>

	#include "soc.h"
	#include "iomap.h"
	#include "common.h"
	#include "cm-regbits-34xx.h"
	#include "prm-regbits-34xx.h"
	#include "prm3xxx.h"
	#include "cm3xxx.h"
	#include "sdrc.h"
	#include "pm.h"
	#include "control.h"

	/* Used by omap3_ctrl_save_padconf() */
	#define START_PADCONF_SAVE 0x2
	#define PADCONF_SAVE_DONE 0x1

	static void __iomem *omap2_ctrl_base;
	static void __iomem *omap4_ctrl_pad_base;

	#if defined(CONFIG_ARCH_OMAP3) && defined(CONFIG_PM)
	struct omap3_scratchpad {
	u32 boot_config_ptr;
	u32 public_restore_ptr;
	u32 secure_ram_restore_ptr;
	u32 sdrc_module_semaphore;
	u32 prcm_block_offset;
	u32 sdrc_block_offset;
	};

	struct omap3_scratchpad_prcm_block {
	u32 prm_clksrc_ctrl;
	u32 prm_clksel;
	u32 cm_contents[11];
	u32 prcm_block_size;
	};

	struct omap3_scratchpad_sdrc_block {
	u16 sysconfig;
	u16 cs_cfg;
	u16 sharing;
	u16 err_type;
	u32 dll_a_ctrl;
	u32 dll_b_ctrl;
	u32 power;
	u32 cs_0;
	u32 mcfg_0;
	u16 mr_0;
	u16 emr_1_0;
	u16 emr_2_0;
	u16 emr_3_0;
	u32 actim_ctrla_0;
	u32 actim_ctrlb_0;
	u32 rfr_ctrl_0;
	u32 cs_1;
	u32 mcfg_1;
	u16 mr_1;
	u16 emr_1_1;
	u16 emr_2_1;
	u16 emr_3_1;
	u32 actim_ctrla_1;
	u32 actim_ctrlb_1;
	u32 rfr_ctrl_1;
	u16 dcdl_1_ctrl;
	u16 dcdl_2_ctrl;
	u32 flags;
	u32 block_size;
	};

	void *omap3_secure_ram_storage;

	/*
	* This is used to store ARM registers in SDRAM before attempting
	* an MPU OFF. The save and restore happens from the SRAM sleep code.
	* The address is stored in scratchpad, so that it can be used
	* during the restore path.
	*/
	u32 omap3_arm_context[128];

	struct omap3_control_regs {
	u32 sysconfig;
	u32 devconf0;
	u32 mem_dftrw0;
	u32 mem_dftrw1;
	u32 msuspendmux_0;
	u32 msuspendmux_1;
	u32 msuspendmux_2;
	u32 msuspendmux_3;
	u32 msuspendmux_4;
	u32 msuspendmux_5;
	u32 sec_ctrl;
	u32 devconf1;
	u32 csirxfe;
	u32 iva2_bootaddr;
	u32 iva2_bootmod;
	u32 debobs_0;
	u32 debobs_1;
	u32 debobs_2;
	u32 debobs_3;
	u32 debobs_4;
	u32 debobs_5;
	u32 debobs_6;
	u32 debobs_7;
	u32 debobs_8;
	u32 prog_io0;
	u32 prog_io1;
	u32 dss_dpll_spreading;
	u32 core_dpll_spreading;
	u32 per_dpll_spreading;
	u32 usbhost_dpll_spreading;
	u32 pbias_lite;
	u32 temp_sensor;
	u32 sramldo4;
	u32 sramldo5;
	u32 csi;
	u32 padconf_sys_nirq;
	};

	static struct omap3_control_regs control_context;
	#endif /* CONFIG_ARCH_OMAP3 && CONFIG_PM */

	#define OMAP_CTRL_REGADDR(reg) (omap2_ctrl_base + (reg))
	#define OMAP4_CTRL_PAD_REGADDR(reg) (omap4_ctrl_pad_base + (reg))

	void __init omap2_set_globals_control(void __iomem *ctrl,
	void __iomem *ctrl_pad)
	{
	omap2_ctrl_base = ctrl;
	omap4_ctrl_pad_base = ctrl_pad;
	}

	void __iomem *omap_ctrl_base_get(void)
	{
	return omap2_ctrl_base;
	}

	u8 omap_ctrl_readb(u16 offset)
	{
	return readb_relaxed(OMAP_CTRL_REGADDR(offset));
	}

	u16 omap_ctrl_readw(u16 offset)
	{
	return readw_relaxed(OMAP_CTRL_REGADDR(offset));
	}

	u32 omap_ctrl_readl(u16 offset)
	{
	return readl_relaxed(OMAP_CTRL_REGADDR(offset));
	}

	void omap_ctrl_writeb(u8 val, u16 offset)
	{
	writeb_relaxed(val, OMAP_CTRL_REGADDR(offset));
	}

	void omap_ctrl_writew(u16 val, u16 offset)
	{
	writew_relaxed(val, OMAP_CTRL_REGADDR(offset));
	}

	void omap_ctrl_writel(u32 val, u16 offset)
	{
	writel_relaxed(val, OMAP_CTRL_REGADDR(offset));
	}

	/*
	* On OMAP4 control pad are not addressable from control
	* core base. So the common omap_ctrl_read/write APIs breaks
	* Hence export separate APIs to manage the omap4 pad control
	* registers. This APIs will work only for OMAP4
	*/

	u32 omap4_ctrl_pad_readl(u16 offset)
	{
	return readl_relaxed(OMAP4_CTRL_PAD_REGADDR(offset));
	}

	void omap4_ctrl_pad_writel(u32 val, u16 offset)
	{
	writel_relaxed(val, OMAP4_CTRL_PAD_REGADDR(offset));
	}

	#ifdef CONFIG_ARCH_OMAP3

	/**
	* omap3_ctrl_write_boot_mode - set scratchpad boot mode for the next boot
	* @bootmode: 8-bit value to pass to some boot code
	*
	* Set the bootmode in the scratchpad RAM. This is used after the
	* system restarts. Not sure what actually uses this - it may be the
	* bootloader, rather than the boot ROM - contrary to the preserved
	* comment below. No return value.
	*/
	void omap3_ctrl_write_boot_mode(u8 bootmode)
	{
	u32 l;

	l = ('B' << 24) \| ('M' << 16) \| bootmode;

	/*
	* Reserve the first word in scratchpad for communicating
	* with the boot ROM. A pointer to a data structure
	* describing the boot process can be stored there,
	* cf. OMAP34xx TRM, Initialization / Software Booting
	* Configuration.
	*
	* XXX This should use some omap_ctrl_writel()-type function
	*/
	writel_relaxed(l, OMAP2_L4_IO_ADDRESS(OMAP343X_SCRATCHPAD + 4));
	}

	#endif

	/**
	* omap_ctrl_write_dsp_boot_addr - set boot address for a remote processor
	* @bootaddr: physical address of the boot loader
	*
	* Set boot address for the boot loader of a supported processor
	* when a power ON sequence occurs.
	*/
	void omap_ctrl_write_dsp_boot_addr(u32 bootaddr)
	{
	u32 offset = cpu_is_omap243x() ? OMAP243X_CONTROL_IVA2_BOOTADDR :
	cpu_is_omap34xx() ? OMAP343X_CONTROL_IVA2_BOOTADDR :
	cpu_is_omap44xx() ? OMAP4_CTRL_MODULE_CORE_DSP_BOOTADDR :
	soc_is_omap54xx() ? OMAP4_CTRL_MODULE_CORE_DSP_BOOTADDR :
	0;

	if (!offset) {
	pr_err("%s: unsupported omap type\n", __func__);
	return;
	}

	omap_ctrl_writel(bootaddr, offset);
	}

	/**
	* omap_ctrl_write_dsp_boot_mode - set boot mode for a remote processor
	* @bootmode: 8-bit value to pass to some boot code
	*
	* Sets boot mode for the boot loader of a supported processor
	* when a power ON sequence occurs.
	*/
	void omap_ctrl_write_dsp_boot_mode(u8 bootmode)
	{
	u32 offset = cpu_is_omap243x() ? OMAP243X_CONTROL_IVA2_BOOTMOD :
	cpu_is_omap34xx() ? OMAP343X_CONTROL_IVA2_BOOTMOD :
	0;

	if (!offset) {
	pr_err("%s: unsupported omap type\n", __func__);
	return;
	}

	omap_ctrl_writel(bootmode, offset);
	}

	#if defined(CONFIG_ARCH_OMAP3) && defined(CONFIG_PM)
	/*
	* Clears the scratchpad contents in case of cold boot-
	* called during bootup
	*/
	void omap3_clear_scratchpad_contents(void)
	{
	u32 max_offset = OMAP343X_SCRATCHPAD_ROM_OFFSET;
	void __iomem *v_addr;
	u32 offset = 0;
	v_addr = OMAP2_L4_IO_ADDRESS(OMAP343X_SCRATCHPAD_ROM);
	if (omap2_prm_read_mod_reg(OMAP3430_GR_MOD, OMAP3_PRM_RSTST_OFFSET) &
	OMAP3430_GLOBAL_COLD_RST_MASK) {
	for ( ; offset <= max_offset; offset += 0x4)
	writel_relaxed(0x0, (v_addr + offset));
	omap2_prm_set_mod_reg_bits(OMAP3430_GLOBAL_COLD_RST_MASK,
	OMAP3430_GR_MOD,
	OMAP3_PRM_RSTST_OFFSET);
	}
	}

	/* Populate the scratchpad structure with restore structure */
	void omap3_save_scratchpad_contents(void)
	{
	void __iomem *scratchpad_address;
	u32 arm_context_addr;
	struct omap3_scratchpad scratchpad_contents;
	struct omap3_scratchpad_prcm_block prcm_block_contents;
	struct omap3_scratchpad_sdrc_block sdrc_block_contents;

	/*
	* Populate the Scratchpad contents
	*
	* The "get_*restore_pointer" functions are used to provide a
	* physical restore address where the ROM code jumps while waking
	* up from MPU OFF/OSWR state.
	* The restore pointer is stored into the scratchpad.
	*/
	scratchpad_contents.boot_config_ptr = 0x0;
	if (cpu_is_omap3630())
	scratchpad_contents.public_restore_ptr =
	virt_to_phys(omap3_restore_3630);
	else if (omap_rev() != OMAP3430_REV_ES3_0 &&
	omap_rev() != OMAP3430_REV_ES3_1)
	scratchpad_contents.public_restore_ptr =
	virt_to_phys(omap3_restore);
	else
	scratchpad_contents.public_restore_ptr =
	virt_to_phys(omap3_restore_es3);

	if (omap_type() == OMAP2_DEVICE_TYPE_GP)
	scratchpad_contents.secure_ram_restore_ptr = 0x0;
	else
	scratchpad_contents.secure_ram_restore_ptr =
	(u32) __pa(omap3_secure_ram_storage);
	scratchpad_contents.sdrc_module_semaphore = 0x0;
	scratchpad_contents.prcm_block_offset = 0x2C;
	scratchpad_contents.sdrc_block_offset = 0x64;

	/* Populate the PRCM block contents */
	prcm_block_contents.prm_clksrc_ctrl =
	omap2_prm_read_mod_reg(OMAP3430_GR_MOD,
	OMAP3_PRM_CLKSRC_CTRL_OFFSET);
	prcm_block_contents.prm_clksel =
	omap2_prm_read_mod_reg(OMAP3430_CCR_MOD,
	OMAP3_PRM_CLKSEL_OFFSET);

	omap3_cm_save_scratchpad_contents(prcm_block_contents.cm_contents);

	prcm_block_contents.prcm_block_size = 0x0;

	/* Populate the SDRC block contents */
	sdrc_block_contents.sysconfig =
	(sdrc_read_reg(SDRC_SYSCONFIG) & 0xFFFF);
	sdrc_block_contents.cs_cfg =
	(sdrc_read_reg(SDRC_CS_CFG) & 0xFFFF);
	sdrc_block_contents.sharing =
	(sdrc_read_reg(SDRC_SHARING) & 0xFFFF);
	sdrc_block_contents.err_type =
	(sdrc_read_reg(SDRC_ERR_TYPE) & 0xFFFF);
	sdrc_block_contents.dll_a_ctrl = sdrc_read_reg(SDRC_DLLA_CTRL);
	sdrc_block_contents.dll_b_ctrl = 0x0;
	/*
	* Due to a OMAP3 errata (1.142), on EMU/HS devices SRDC should
	* be programed to issue automatic self refresh on timeout
	* of AUTO_CNT = 1 prior to any transition to OFF mode.
	*/
	if ((omap_type() != OMAP2_DEVICE_TYPE_GP)
	&& (omap_rev() >= OMAP3430_REV_ES3_0))
	sdrc_block_contents.power = (sdrc_read_reg(SDRC_POWER) &
	~(SDRC_POWER_AUTOCOUNT_MASK\|
	SDRC_POWER_CLKCTRL_MASK)) \|
	(1 << SDRC_POWER_AUTOCOUNT_SHIFT) \|
	SDRC_SELF_REFRESH_ON_AUTOCOUNT;
	else
	sdrc_block_contents.power = sdrc_read_reg(SDRC_POWER);

	sdrc_block_contents.cs_0 = 0x0;
	sdrc_block_contents.mcfg_0 = sdrc_read_reg(SDRC_MCFG_0);
	sdrc_block_contents.mr_0 = (sdrc_read_reg(SDRC_MR_0) & 0xFFFF);
	sdrc_block_contents.emr_1_0 = 0x0;
	sdrc_block_contents.emr_2_0 = 0x0;
	sdrc_block_contents.emr_3_0 = 0x0;
	sdrc_block_contents.actim_ctrla_0 =
	sdrc_read_reg(SDRC_ACTIM_CTRL_A_0);
	sdrc_block_contents.actim_ctrlb_0 =
	sdrc_read_reg(SDRC_ACTIM_CTRL_B_0);
	sdrc_block_contents.rfr_ctrl_0 =
	sdrc_read_reg(SDRC_RFR_CTRL_0);
	sdrc_block_contents.cs_1 = 0x0;
	sdrc_block_contents.mcfg_1 = sdrc_read_reg(SDRC_MCFG_1);
	sdrc_block_contents.mr_1 = sdrc_read_reg(SDRC_MR_1) & 0xFFFF;
	sdrc_block_contents.emr_1_1 = 0x0;
	sdrc_block_contents.emr_2_1 = 0x0;
	sdrc_block_contents.emr_3_1 = 0x0;
	sdrc_block_contents.actim_ctrla_1 =
	sdrc_read_reg(SDRC_ACTIM_CTRL_A_1);
	sdrc_block_contents.actim_ctrlb_1 =
	sdrc_read_reg(SDRC_ACTIM_CTRL_B_1);
	sdrc_block_contents.rfr_ctrl_1 =
	sdrc_read_reg(SDRC_RFR_CTRL_1);
	sdrc_block_contents.dcdl_1_ctrl = 0x0;
	sdrc_block_contents.dcdl_2_ctrl = 0x0;
	sdrc_block_contents.flags = 0x0;
	sdrc_block_contents.block_size = 0x0;

	arm_context_addr = virt_to_phys(omap3_arm_context);

	/* Copy all the contents to the scratchpad location */
	scratchpad_address = OMAP2_L4_IO_ADDRESS(OMAP343X_SCRATCHPAD);
	memcpy_toio(scratchpad_address, &scratchpad_contents,
	sizeof(scratchpad_contents));
	/* Scratchpad contents being 32 bits, a divide by 4 done here */
	memcpy_toio(scratchpad_address +
	scratchpad_contents.prcm_block_offset,
	&prcm_block_contents, sizeof(prcm_block_contents));
	memcpy_toio(scratchpad_address +
	scratchpad_contents.sdrc_block_offset,
	&sdrc_block_contents, sizeof(sdrc_block_contents));
	/*
	* Copies the address of the location in SDRAM where ARM
	* registers get saved during a MPU OFF transition.
	*/
	memcpy_toio(scratchpad_address +
	scratchpad_contents.sdrc_block_offset +
	sizeof(sdrc_block_contents), &arm_context_addr, 4);
	}

	void omap3_control_save_context(void)
	{
	control_context.sysconfig = omap_ctrl_readl(OMAP2_CONTROL_SYSCONFIG);
	control_context.devconf0 = omap_ctrl_readl(OMAP2_CONTROL_DEVCONF0);
	control_context.mem_dftrw0 =
	omap_ctrl_readl(OMAP343X_CONTROL_MEM_DFTRW0);
	control_context.mem_dftrw1 =
	omap_ctrl_readl(OMAP343X_CONTROL_MEM_DFTRW1);
	control_context.msuspendmux_0 =
	omap_ctrl_readl(OMAP2_CONTROL_MSUSPENDMUX_0);
	control_context.msuspendmux_1 =
	omap_ctrl_readl(OMAP2_CONTROL_MSUSPENDMUX_1);
	control_context.msuspendmux_2 =
	omap_ctrl_readl(OMAP2_CONTROL_MSUSPENDMUX_2);
	control_context.msuspendmux_3 =
	omap_ctrl_readl(OMAP2_CONTROL_MSUSPENDMUX_3);
	control_context.msuspendmux_4 =
	omap_ctrl_readl(OMAP2_CONTROL_MSUSPENDMUX_4);
	control_context.msuspendmux_5 =
	omap_ctrl_readl(OMAP2_CONTROL_MSUSPENDMUX_5);
	control_context.sec_ctrl = omap_ctrl_readl(OMAP2_CONTROL_SEC_CTRL);
	control_context.devconf1 = omap_ctrl_readl(OMAP343X_CONTROL_DEVCONF1);
	control_context.csirxfe = omap_ctrl_readl(OMAP343X_CONTROL_CSIRXFE);
	control_context.iva2_bootaddr =
	omap_ctrl_readl(OMAP343X_CONTROL_IVA2_BOOTADDR);
	control_context.iva2_bootmod =
	omap_ctrl_readl(OMAP343X_CONTROL_IVA2_BOOTMOD);
	control_context.debobs_0 = omap_ctrl_readl(OMAP343X_CONTROL_DEBOBS(0));
	control_context.debobs_1 = omap_ctrl_readl(OMAP343X_CONTROL_DEBOBS(1));
	control_context.debobs_2 = omap_ctrl_readl(OMAP343X_CONTROL_DEBOBS(2));
	control_context.debobs_3 = omap_ctrl_readl(OMAP343X_CONTROL_DEBOBS(3));
	control_context.debobs_4 = omap_ctrl_readl(OMAP343X_CONTROL_DEBOBS(4));
	control_context.debobs_5 = omap_ctrl_readl(OMAP343X_CONTROL_DEBOBS(5));
	control_context.debobs_6 = omap_ctrl_readl(OMAP343X_CONTROL_DEBOBS(6));
	control_context.debobs_7 = omap_ctrl_readl(OMAP343X_CONTROL_DEBOBS(7));
	control_context.debobs_8 = omap_ctrl_readl(OMAP343X_CONTROL_DEBOBS(8));
	control_context.prog_io0 = omap_ctrl_readl(OMAP343X_CONTROL_PROG_IO0);
	control_context.prog_io1 = omap_ctrl_readl(OMAP343X_CONTROL_PROG_IO1);
	control_context.dss_dpll_spreading =
	omap_ctrl_readl(OMAP343X_CONTROL_DSS_DPLL_SPREADING);
	control_context.core_dpll_spreading =
	omap_ctrl_readl(OMAP343X_CONTROL_CORE_DPLL_SPREADING);
	control_context.per_dpll_spreading =
	omap_ctrl_readl(OMAP343X_CONTROL_PER_DPLL_SPREADING);
	control_context.usbhost_dpll_spreading =
	omap_ctrl_readl(OMAP343X_CONTROL_USBHOST_DPLL_SPREADING);
	control_context.pbias_lite =
	omap_ctrl_readl(OMAP343X_CONTROL_PBIAS_LITE);
	control_context.temp_sensor =
	omap_ctrl_readl(OMAP343X_CONTROL_TEMP_SENSOR);
	control_context.sramldo4 = omap_ctrl_readl(OMAP343X_CONTROL_SRAMLDO4);
	control_context.sramldo5 = omap_ctrl_readl(OMAP343X_CONTROL_SRAMLDO5);
	control_context.csi = omap_ctrl_readl(OMAP343X_CONTROL_CSI);
	control_context.padconf_sys_nirq =
	omap_ctrl_readl(OMAP343X_CONTROL_PADCONF_SYSNIRQ);
	return;
	}

	void omap3_control_restore_context(void)
	{
	omap_ctrl_writel(control_context.sysconfig, OMAP2_CONTROL_SYSCONFIG);
	omap_ctrl_writel(control_context.devconf0, OMAP2_CONTROL_DEVCONF0);
	omap_ctrl_writel(control_context.mem_dftrw0,
	OMAP343X_CONTROL_MEM_DFTRW0);
	omap_ctrl_writel(control_context.mem_dftrw1,
	OMAP343X_CONTROL_MEM_DFTRW1);
	omap_ctrl_writel(control_context.msuspendmux_0,
	OMAP2_CONTROL_MSUSPENDMUX_0);
	omap_ctrl_writel(control_context.msuspendmux_1,
	OMAP2_CONTROL_MSUSPENDMUX_1);
	omap_ctrl_writel(control_context.msuspendmux_2,
	OMAP2_CONTROL_MSUSPENDMUX_2);
	omap_ctrl_writel(control_context.msuspendmux_3,
	OMAP2_CONTROL_MSUSPENDMUX_3);
	omap_ctrl_writel(control_context.msuspendmux_4,
	OMAP2_CONTROL_MSUSPENDMUX_4);
	omap_ctrl_writel(control_context.msuspendmux_5,
	OMAP2_CONTROL_MSUSPENDMUX_5);
	omap_ctrl_writel(control_context.sec_ctrl, OMAP2_CONTROL_SEC_CTRL);
	omap_ctrl_writel(control_context.devconf1, OMAP343X_CONTROL_DEVCONF1);
	omap_ctrl_writel(control_context.csirxfe, OMAP343X_CONTROL_CSIRXFE);
	omap_ctrl_writel(control_context.iva2_bootaddr,
	OMAP343X_CONTROL_IVA2_BOOTADDR);
	omap_ctrl_writel(control_context.iva2_bootmod,
	OMAP343X_CONTROL_IVA2_BOOTMOD);
	omap_ctrl_writel(control_context.debobs_0, OMAP343X_CONTROL_DEBOBS(0));
	omap_ctrl_writel(control_context.debobs_1, OMAP343X_CONTROL_DEBOBS(1));
	omap_ctrl_writel(control_context.debobs_2, OMAP343X_CONTROL_DEBOBS(2));
	omap_ctrl_writel(control_context.debobs_3, OMAP343X_CONTROL_DEBOBS(3));
	omap_ctrl_writel(control_context.debobs_4, OMAP343X_CONTROL_DEBOBS(4));
	omap_ctrl_writel(control_context.debobs_5, OMAP343X_CONTROL_DEBOBS(5));
	omap_ctrl_writel(control_context.debobs_6, OMAP343X_CONTROL_DEBOBS(6));
	omap_ctrl_writel(control_context.debobs_7, OMAP343X_CONTROL_DEBOBS(7));
	omap_ctrl_writel(control_context.debobs_8, OMAP343X_CONTROL_DEBOBS(8));
	omap_ctrl_writel(control_context.prog_io0, OMAP343X_CONTROL_PROG_IO0);
	omap_ctrl_writel(control_context.prog_io1, OMAP343X_CONTROL_PROG_IO1);
	omap_ctrl_writel(control_context.dss_dpll_spreading,
	OMAP343X_CONTROL_DSS_DPLL_SPREADING);
	omap_ctrl_writel(control_context.core_dpll_spreading,
	OMAP343X_CONTROL_CORE_DPLL_SPREADING);
	omap_ctrl_writel(control_context.per_dpll_spreading,
	OMAP343X_CONTROL_PER_DPLL_SPREADING);
	omap_ctrl_writel(control_context.usbhost_dpll_spreading,
	OMAP343X_CONTROL_USBHOST_DPLL_SPREADING);
	omap_ctrl_writel(control_context.pbias_lite,
	OMAP343X_CONTROL_PBIAS_LITE);
	omap_ctrl_writel(control_context.temp_sensor,
	OMAP343X_CONTROL_TEMP_SENSOR);
	omap_ctrl_writel(control_context.sramldo4, OMAP343X_CONTROL_SRAMLDO4);
	omap_ctrl_writel(control_context.sramldo5, OMAP343X_CONTROL_SRAMLDO5);
	omap_ctrl_writel(control_context.csi, OMAP343X_CONTROL_CSI);
	omap_ctrl_writel(control_context.padconf_sys_nirq,
	OMAP343X_CONTROL_PADCONF_SYSNIRQ);
	return;
	}

	void omap3630_ctrl_disable_rta(void)
	{
	if (!cpu_is_omap3630())
	return;
	omap_ctrl_writel(OMAP36XX_RTA_DISABLE, OMAP36XX_CONTROL_MEM_RTA_CTRL);
	}

	/**
	* omap3_ctrl_save_padconf - save padconf registers to scratchpad RAM
	*
	* Tell the SCM to start saving the padconf registers, then wait for
	* the process to complete. Returns 0 unconditionally, although it
	* should also eventually be able to return -ETIMEDOUT, if the save
	* does not complete.
	*
	* XXX This function is missing a timeout. What should it be?
	*/
	int omap3_ctrl_save_padconf(void)
	{
	u32 cpo;

	/* Save the padconf registers */
	cpo = omap_ctrl_readl(OMAP343X_CONTROL_PADCONF_OFF);
	cpo \|= START_PADCONF_SAVE;
	omap_ctrl_writel(cpo, OMAP343X_CONTROL_PADCONF_OFF);

	/* wait for the save to complete */
	while (!(omap_ctrl_readl(OMAP343X_CONTROL_GENERAL_PURPOSE_STATUS)
	& PADCONF_SAVE_DONE))
	udelay(1);

	return 0;
	}

	/**
	* omap3_ctrl_set_iva_bootmode_idle - sets the IVA2 bootmode to idle
	*
	* Sets the bootmode for IVA2 to idle. This is needed by the PM code to
	* force disable IVA2 so that it does not prevent any low-power states.
	*/
	void omap3_ctrl_set_iva_bootmode_idle(void)
	{
	omap_ctrl_writel(OMAP3_IVA2_BOOTMOD_IDLE,
	OMAP343X_CONTROL_IVA2_BOOTMOD);
	}
	#endif /* CONFIG_ARCH_OMAP3 && CONFIG_PM */