drivers/hwmon/adm1031.c

/*
  adm1031.c - Part of lm_sensors, Linux kernel modules for hardware
  monitoring
  Based on lm75.c and lm85.c
  Supports adm1030 / adm1031
  Copyright (C) 2004 Alexandre d'Alton <alex@alexdalton.org>
  Reworked by Jean Delvare <khali@linux-fr.org>
  
  This program is free software; you can redistribute it and/or modify
  it under the terms of the GNU General Public License as published by
  the Free Software Foundation; either version 2 of the License, or
  (at your option) any later version.

  This program is distributed in the hope that it will be useful,
  but WITHOUT ANY WARRANTY; without even the implied warranty of
  MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
  GNU General Public License for more details.

  You should have received a copy of the GNU General Public License
  along with this program; if not, write to the Free Software
  Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
*/

#include <linux/module.h>
#include <linux/init.h>
#include <linux/slab.h>
#include <linux/jiffies.h>
#include <linux/i2c.h>
#include <linux/i2c-sensor.h>

/* Following macros takes channel parameter starting from 0 to 2 */
#define ADM1031_REG_FAN_SPEED(nr)	(0x08 + (nr))
#define ADM1031_REG_FAN_DIV(nr)		(0x20  + (nr))
#define ADM1031_REG_PWM			(0x22)
#define ADM1031_REG_FAN_MIN(nr)		(0x10 + (nr))

#define ADM1031_REG_TEMP_MAX(nr)	(0x14  + 4*(nr))
#define ADM1031_REG_TEMP_MIN(nr)	(0x15  + 4*(nr))
#define ADM1031_REG_TEMP_CRIT(nr)	(0x16  + 4*(nr))

#define ADM1031_REG_TEMP(nr)		(0xa + (nr))
#define ADM1031_REG_AUTO_TEMP(nr)	(0x24 + (nr))

#define ADM1031_REG_STATUS(nr)		(0x2 + (nr))

#define ADM1031_REG_CONF1		0x0
#define ADM1031_REG_CONF2		0x1
#define ADM1031_REG_EXT_TEMP		0x6

#define ADM1031_CONF1_MONITOR_ENABLE	0x01	/* Monitoring enable */
#define ADM1031_CONF1_PWM_INVERT	0x08	/* PWM Invert */
#define ADM1031_CONF1_AUTO_MODE		0x80	/* Auto FAN */

#define ADM1031_CONF2_PWM1_ENABLE	0x01
#define ADM1031_CONF2_PWM2_ENABLE	0x02
#define ADM1031_CONF2_TACH1_ENABLE	0x04
#define ADM1031_CONF2_TACH2_ENABLE	0x08
#define ADM1031_CONF2_TEMP_ENABLE(chan)	(0x10 << (chan))

/* Addresses to scan */
static unsigned short normal_i2c[] = { 0x2c, 0x2d, 0x2e, I2C_CLIENT_END };
static unsigned int normal_isa[] = { I2C_CLIENT_ISA_END };

/* Insmod parameters */
SENSORS_INSMOD_2(adm1030, adm1031);

typedef u8 auto_chan_table_t[8][2];

/* Each client has this additional data */
struct adm1031_data {
	struct i2c_client client;
	struct semaphore update_lock;
	int chip_type;
	char valid;		/* !=0 if following fields are valid */
	unsigned long last_updated;	/* In jiffies */
	/* The chan_select_table contains the possible configurations for
	 * auto fan control.
	 */
	auto_chan_table_t *chan_select_table;
	u16 alarm;
	u8 conf1;
	u8 conf2;
	u8 fan[2];
	u8 fan_div[2];
	u8 fan_min[2];
	u8 pwm[2];
	u8 old_pwm[2];
	s8 temp[3];
	u8 ext_temp[3];
	u8 auto_temp[3];
	u8 auto_temp_min[3];
	u8 auto_temp_off[3];
	u8 auto_temp_max[3];
	s8 temp_min[3];
	s8 temp_max[3];
	s8 temp_crit[3];
};

static int adm1031_attach_adapter(struct i2c_adapter *adapter);
static int adm1031_detect(struct i2c_adapter *adapter, int address, int kind);
static void adm1031_init_client(struct i2c_client *client);
static int adm1031_detach_client(struct i2c_client *client);
static struct adm1031_data *adm1031_update_device(struct device *dev);

/* This is the driver that will be inserted */
static struct i2c_driver adm1031_driver = {
	.owner = THIS_MODULE,
	.name = "adm1031",
	.flags = I2C_DF_NOTIFY,
	.attach_adapter = adm1031_attach_adapter,
	.detach_client = adm1031_detach_client,
};

static inline u8 adm1031_read_value(struct i2c_client *client, u8 reg)
{
	return i2c_smbus_read_byte_data(client, reg);
}

static inline int
adm1031_write_value(struct i2c_client *client, u8 reg, unsigned int value)
{
	return i2c_smbus_write_byte_data(client, reg, value);
}


#define TEMP_TO_REG(val)		(((val) < 0 ? ((val - 500) / 1000) : \
					((val + 500) / 1000)))

#define TEMP_FROM_REG(val)		((val) * 1000)

#define TEMP_FROM_REG_EXT(val, ext)	(TEMP_FROM_REG(val) + (ext) * 125)

#define FAN_FROM_REG(reg, div)		((reg) ? (11250 * 60) / ((reg) * (div)) : 0)

static int FAN_TO_REG(int reg, int div)
{
	int tmp;
	tmp = FAN_FROM_REG(SENSORS_LIMIT(reg, 0, 65535), div);
	return tmp > 255 ? 255 : tmp;
}

#define FAN_DIV_FROM_REG(reg)		(1<<(((reg)&0xc0)>>6))

#define PWM_TO_REG(val)			(SENSORS_LIMIT((val), 0, 255) >> 4)
#define PWM_FROM_REG(val)		((val) << 4)

#define FAN_CHAN_FROM_REG(reg)		(((reg) >> 5) & 7)
#define FAN_CHAN_TO_REG(val, reg)	\
	(((reg) & 0x1F) | (((val) << 5) & 0xe0))

#define AUTO_TEMP_MIN_TO_REG(val, reg)	\
	((((val)/500) & 0xf8)|((reg) & 0x7))
#define AUTO_TEMP_RANGE_FROM_REG(reg)	(5000 * (1<< ((reg)&0x7)))
#define AUTO_TEMP_MIN_FROM_REG(reg)	(1000 * ((((reg) >> 3) & 0x1f) << 2))

#define AUTO_TEMP_MIN_FROM_REG_DEG(reg)	((((reg) >> 3) & 0x1f) << 2)

#define AUTO_TEMP_OFF_FROM_REG(reg)		\
	(AUTO_TEMP_MIN_FROM_REG(reg) - 5000)

#define AUTO_TEMP_MAX_FROM_REG(reg)		\
	(AUTO_TEMP_RANGE_FROM_REG(reg) +	\
	AUTO_TEMP_MIN_FROM_REG(reg))

static int AUTO_TEMP_MAX_TO_REG(int val, int reg, int pwm)
{
	int ret;
	int range = val - AUTO_TEMP_MIN_FROM_REG(reg);

	range = ((val - AUTO_TEMP_MIN_FROM_REG(reg))*10)/(16 - pwm);
	ret = ((reg & 0xf8) |
	       (range < 10000 ? 0 :
		range < 20000 ? 1 :
		range < 40000 ? 2 : range < 80000 ? 3 : 4));
	return ret;
}

/* FAN auto control */
#define GET_FAN_AUTO_BITFIELD(data, idx)	\
	(*(data)->chan_select_table)[FAN_CHAN_FROM_REG((data)->conf1)][idx%2]

/* The tables below contains the possible values for the auto fan 
 * control bitfields. the index in the table is the register value.
 * MSb is the auto fan control enable bit, so the four first entries
 * in the table disables auto fan control when both bitfields are zero.
 */
static auto_chan_table_t auto_channel_select_table_adm1031 = {
	{0, 0}, {0, 0}, {0, 0}, {0, 0},
	{2 /*0b010 */ , 4 /*0b100 */ },
	{2 /*0b010 */ , 2 /*0b010 */ },
	{4 /*0b100 */ , 4 /*0b100 */ },
	{7 /*0b111 */ , 7 /*0b111 */ },
};

static auto_chan_table_t auto_channel_select_table_adm1030 = {
	{0, 0}, {0, 0}, {0, 0}, {0, 0},
	{2 /*0b10 */		, 0},
	{0xff /*invalid */	, 0},
	{0xff /*invalid */	, 0},
	{3 /*0b11 */		, 0},
};

/* That function checks if a bitfield is valid and returns the other bitfield
 * nearest match if no exact match where found.
 */
static int
get_fan_auto_nearest(struct adm1031_data *data,
		     int chan, u8 val, u8 reg, u8 * new_reg)
{
	int i;
	int first_match = -1, exact_match = -1;
	u8 other_reg_val =
	    (*data->chan_select_table)[FAN_CHAN_FROM_REG(reg)][chan ? 0 : 1];

	if (val == 0) {
		*new_reg = 0;
		return 0;
	}

	for (i = 0; i < 8; i++) {
		if ((val == (*data->chan_select_table)[i][chan]) &&
		    ((*data->chan_select_table)[i][chan ? 0 : 1] ==
		     other_reg_val)) {
			/* We found an exact match */
			exact_match = i;
			break;
		} else if (val == (*data->chan_select_table)[i][chan] &&
			   first_match == -1) {
			/* Save the first match in case of an exact match has not been
			 * found 
			 */
			first_match = i;
		}
	}

	if (exact_match >= 0) {
		*new_reg = exact_match;
	} else if (first_match >= 0) {
		*new_reg = first_match;
	} else {
		return -EINVAL;
	}
	return 0;
}

static ssize_t show_fan_auto_channel(struct device *dev, char *buf, int nr)
{
	struct adm1031_data *data = adm1031_update_device(dev);
	return sprintf(buf, "%d\n", GET_FAN_AUTO_BITFIELD(data, nr));
}

static ssize_t
set_fan_auto_channel(struct device *dev, const char *buf, size_t count, int nr)
{
	struct i2c_client *client = to_i2c_client(dev);
	struct adm1031_data *data = i2c_get_clientdata(client);
	int val = simple_strtol(buf, NULL, 10);
	u8 reg;
	int ret;
	u8 old_fan_mode;

	old_fan_mode = data->conf1;

	down(&data->update_lock);
	
	if ((ret = get_fan_auto_nearest(data, nr, val, data->conf1, &reg))) {
		up(&data->update_lock);
		return ret;
	}
	if (((data->conf1 = FAN_CHAN_TO_REG(reg, data->conf1)) & ADM1031_CONF1_AUTO_MODE) ^ 
	    (old_fan_mode & ADM1031_CONF1_AUTO_MODE)) {
		if (data->conf1 & ADM1031_CONF1_AUTO_MODE){
			/* Switch to Auto Fan Mode 
			 * Save PWM registers 
			 * Set PWM registers to 33% Both */
			data->old_pwm[0] = data->pwm[0];
			data->old_pwm[1] = data->pwm[1];
			adm1031_write_value(client, ADM1031_REG_PWM, 0x55);
		} else {
			/* Switch to Manual Mode */
			data->pwm[0] = data->old_pwm[0];
			data->pwm[1] = data->old_pwm[1];
			/* Restore PWM registers */
			adm1031_write_value(client, ADM1031_REG_PWM, 
					    data->pwm[0] | (data->pwm[1] << 4));
		}
	}
	data->conf1 = FAN_CHAN_TO_REG(reg, data->conf1);
	adm1031_write_value(client, ADM1031_REG_CONF1, data->conf1);
	up(&data->update_lock);
	return count;
}

#define fan_auto_channel_offset(offset)						\
static ssize_t show_fan_auto_channel_##offset (struct device *dev, struct device_attribute *attr, char *buf)	\
{										\
	return show_fan_auto_channel(dev, buf, offset - 1);			\
}										\
static ssize_t set_fan_auto_channel_##offset (struct device *dev, struct device_attribute *attr,		\
	const char *buf, size_t count)						\
{										\
	return set_fan_auto_channel(dev, buf, count, offset - 1);		\
}										\
static DEVICE_ATTR(auto_fan##offset##_channel, S_IRUGO | S_IWUSR,		\
		   show_fan_auto_channel_##offset,				\
		   set_fan_auto_channel_##offset)

fan_auto_channel_offset(1);
fan_auto_channel_offset(2);

/* Auto Temps */
static ssize_t show_auto_temp_off(struct device *dev, char *buf, int nr)
{
	struct adm1031_data *data = adm1031_update_device(dev);
	return sprintf(buf, "%d\n", 
		       AUTO_TEMP_OFF_FROM_REG(data->auto_temp[nr]));
}
static ssize_t show_auto_temp_min(struct device *dev, char *buf, int nr)
{
	struct adm1031_data *data = adm1031_update_device(dev);
	return sprintf(buf, "%d\n",
		       AUTO_TEMP_MIN_FROM_REG(data->auto_temp[nr]));
}
static ssize_t
set_auto_temp_min(struct device *dev, const char *buf, size_t count, int nr)
{
	struct i2c_client *client = to_i2c_client(dev);
	struct adm1031_data *data = i2c_get_clientdata(client);
	int val = simple_strtol(buf, NULL, 10);

	down(&data->update_lock);
	data->auto_temp[nr] = AUTO_TEMP_MIN_TO_REG(val, data->auto_temp[nr]);
	adm1031_write_value(client, ADM1031_REG_AUTO_TEMP(nr),
			    data->auto_temp[nr]);
	up(&data->update_lock);
	return count;
}
static ssize_t show_auto_temp_max(struct device *dev, char *buf, int nr)
{
	struct adm1031_data *data = adm1031_update_device(dev);
	return sprintf(buf, "%d\n",
		       AUTO_TEMP_MAX_FROM_REG(data->auto_temp[nr]));
}
static ssize_t
set_auto_temp_max(struct device *dev, const char *buf, size_t count, int nr)
{
	struct i2c_client *client = to_i2c_client(dev);
	struct adm1031_data *data = i2c_get_clientdata(client);
	int val = simple_strtol(buf, NULL, 10);

	down(&data->update_lock);
	data->temp_max[nr] = AUTO_TEMP_MAX_TO_REG(val, data->auto_temp[nr], data->pwm[nr]);
	adm1031_write_value(client, ADM1031_REG_AUTO_TEMP(nr),
			    data->temp_max[nr]);
	up(&data->update_lock);
	return count;
}

#define auto_temp_reg(offset)							\
static ssize_t show_auto_temp_##offset##_off (struct device *dev, struct device_attribute *attr, char *buf)	\
{										\
	return show_auto_temp_off(dev, buf, offset - 1);			\
}										\
static ssize_t show_auto_temp_##offset##_min (struct device *dev, struct device_attribute *attr, char *buf)	\
{										\
	return show_auto_temp_min(dev, buf, offset - 1);			\
}										\
static ssize_t show_auto_temp_##offset##_max (struct device *dev, struct device_attribute *attr, char *buf)	\
{										\
	return show_auto_temp_max(dev, buf, offset - 1);			\
}										\
static ssize_t set_auto_temp_##offset##_min (struct device *dev, struct device_attribute *attr,		\
					     const char *buf, size_t count)	\
{										\
	return set_auto_temp_min(dev, buf, count, offset - 1);		\
}										\
static ssize_t set_auto_temp_##offset##_max (struct device *dev, struct device_attribute *attr,		\
					     const char *buf, size_t count)	\
{										\
	return set_auto_temp_max(dev, buf, count, offset - 1);		\
}										\
static DEVICE_ATTR(auto_temp##offset##_off, S_IRUGO,				\
		   show_auto_temp_##offset##_off, NULL);			\
static DEVICE_ATTR(auto_temp##offset##_min, S_IRUGO | S_IWUSR,			\
		   show_auto_temp_##offset##_min, set_auto_temp_##offset##_min);\
static DEVICE_ATTR(auto_temp##offset##_max, S_IRUGO | S_IWUSR,			\
		   show_auto_temp_##offset##_max, set_auto_temp_##offset##_max)

auto_temp_reg(1);
auto_temp_reg(2);
auto_temp_reg(3);

/* pwm */
static ssize_t show_pwm(struct device *dev, char *buf, int nr)
{
	struct adm1031_data *data = adm1031_update_device(dev);
	return sprintf(buf, "%d\n", PWM_FROM_REG(data->pwm[nr]));
}
static ssize_t
set_pwm(struct device *dev, const char *buf, size_t count, int nr)
{
	struct i2c_client *client = to_i2c_client(dev);
	struct adm1031_data *data = i2c_get_clientdata(client);
	int val = simple_strtol(buf, NULL, 10);
	int reg;

	down(&data->update_lock);
	if ((data->conf1 & ADM1031_CONF1_AUTO_MODE) && 
	    (((val>>4) & 0xf) != 5)) {
		/* In automatic mode, the only PWM accepted is 33% */
		up(&data->update_lock);
		return -EINVAL;
	}
	data->pwm[nr] = PWM_TO_REG(val);
	reg = adm1031_read_value(client, ADM1031_REG_PWM);
	adm1031_write_value(client, ADM1031_REG_PWM,
			    nr ? ((data->pwm[nr] << 4) & 0xf0) | (reg & 0xf)
			    : (data->pwm[nr] & 0xf) | (reg & 0xf0));
	up(&data->update_lock);
	return count;
}

#define pwm_reg(offset)							\
static ssize_t show_pwm_##offset (struct device *dev, struct device_attribute *attr, char *buf)	\
{									\
	return show_pwm(dev, buf, offset - 1);			\
}									\
static ssize_t set_pwm_##offset (struct device *dev, struct device_attribute *attr,			\
				 const char *buf, size_t count)		\
{									\
	return set_pwm(dev, buf, count, offset - 1);		\
}									\
static DEVICE_ATTR(pwm##offset, S_IRUGO | S_IWUSR,			\
		   show_pwm_##offset, set_pwm_##offset)

pwm_reg(1);
pwm_reg(2);

/* Fans */

/*
 * That function checks the cases where the fan reading is not
 * relevant.  It is used to provide 0 as fan reading when the fan is
 * not supposed to run
 */
static int trust_fan_readings(struct adm1031_data *data, int chan)
{
	int res = 0;

	if (data->conf1 & ADM1031_CONF1_AUTO_MODE) {
		switch (data->conf1 & 0x60) {
		case 0x00:	/* remote temp1 controls fan1 remote temp2 controls fan2 */
			res = data->temp[chan+1] >=
			      AUTO_TEMP_MIN_FROM_REG_DEG(data->auto_temp[chan+1]);
			break;
		case 0x20:	/* remote temp1 controls both fans */
			res =
			    data->temp[1] >=
			    AUTO_TEMP_MIN_FROM_REG_DEG(data->auto_temp[1]);
			break;
		case 0x40:	/* remote temp2 controls both fans */
			res =
			    data->temp[2] >=
			    AUTO_TEMP_MIN_FROM_REG_DEG(data->auto_temp[2]);
			break;
		case 0x60:	/* max controls both fans */
			res =
			    data->temp[0] >=
			    AUTO_TEMP_MIN_FROM_REG_DEG(data->auto_temp[0])
			    || data->temp[1] >=
			    AUTO_TEMP_MIN_FROM_REG_DEG(data->auto_temp[1])
			    || (data->chip_type == adm1031 
				&& data->temp[2] >=
				AUTO_TEMP_MIN_FROM_REG_DEG(data->auto_temp[2]));
			break;
		}
	} else {
		res = data->pwm[chan] > 0;
	}
	return res;
}


static ssize_t show_fan(struct device *dev, char *buf, int nr)
{
	struct adm1031_data *data = adm1031_update_device(dev);
	int value;

	value = trust_fan_readings(data, nr) ? FAN_FROM_REG(data->fan[nr],
				 FAN_DIV_FROM_REG(data->fan_div[nr])) : 0;
	return sprintf(buf, "%d\n", value);
}

static ssize_t show_fan_div(struct device *dev, char *buf, int nr)
{
	struct adm1031_data *data = adm1031_update_device(dev);
	return sprintf(buf, "%d\n", FAN_DIV_FROM_REG(data->fan_div[nr]));
}
static ssize_t show_fan_min(struct device *dev, char *buf, int nr)
{
	struct adm1031_data *data = adm1031_update_device(dev);
	return sprintf(buf, "%d\n",
		       FAN_FROM_REG(data->fan_min[nr],
				    FAN_DIV_FROM_REG(data->fan_div[nr])));
}
static ssize_t
set_fan_min(struct device *dev, const char *buf, size_t count, int nr)
{
	struct i2c_client *client = to_i2c_client(dev);
	struct adm1031_data *data = i2c_get_clientdata(client);
	int val = simple_strtol(buf, NULL, 10);

	down(&data->update_lock);
	if (val) {
		data->fan_min[nr] = 
			FAN_TO_REG(val, FAN_DIV_FROM_REG(data->fan_div[nr]));
	} else {
		data->fan_min[nr] = 0xff;
	}
	adm1031_write_value(client, ADM1031_REG_FAN_MIN(nr), data->fan_min[nr]);
	up(&data->update_lock);
	return count;
}
static ssize_t
set_fan_div(struct device *dev, const char *buf, size_t count, int nr)
{
	struct i2c_client *client = to_i2c_client(dev);
	struct adm1031_data *data = i2c_get_clientdata(client);
	int val = simple_strtol(buf, NULL, 10);
	u8 tmp;
	int old_div;
	int new_min;

	tmp = val == 8 ? 0xc0 :
	      val == 4 ? 0x80 :
	      val == 2 ? 0x40 :	
	      val == 1 ? 0x00 :  
	      0xff;
	if (tmp == 0xff)
		return -EINVAL;
	
	down(&data->update_lock);
	old_div = FAN_DIV_FROM_REG(data->fan_div[nr]);
	data->fan_div[nr] = (tmp & 0xC0) | (0x3f & data->fan_div[nr]);
	new_min = data->fan_min[nr] * old_div / 
		FAN_DIV_FROM_REG(data->fan_div[nr]);
	data->fan_min[nr] = new_min > 0xff ? 0xff : new_min;
	data->fan[nr] = data->fan[nr] * old_div / 
		FAN_DIV_FROM_REG(data->fan_div[nr]);

	adm1031_write_value(client, ADM1031_REG_FAN_DIV(nr), 
			    data->fan_div[nr]);
	adm1031_write_value(client, ADM1031_REG_FAN_MIN(nr), 
			    data->fan_min[nr]);
	up(&data->update_lock);
	return count;
}

#define fan_offset(offset)						\
static ssize_t show_fan_##offset (struct device *dev, struct device_attribute *attr, char *buf)	\
{									\
	return show_fan(dev, buf, offset - 1);			\
}									\
static ssize_t show_fan_##offset##_min (struct device *dev, struct device_attribute *attr, char *buf)	\
{									\
	return show_fan_min(dev, buf, offset - 1);			\
}									\
static ssize_t show_fan_##offset##_div (struct device *dev, struct device_attribute *attr, char *buf)	\
{									\
	return show_fan_div(dev, buf, offset - 1);			\
}									\
static ssize_t set_fan_##offset##_min (struct device *dev, struct device_attribute *attr,		\
	const char *buf, size_t count)					\
{									\
	return set_fan_min(dev, buf, count, offset - 1);		\
}									\
static ssize_t set_fan_##offset##_div (struct device *dev, struct device_attribute *attr,		\
	const char *buf, size_t count)					\
{									\
	return set_fan_div(dev, buf, count, offset - 1);		\
}									\
static DEVICE_ATTR(fan##offset##_input, S_IRUGO, show_fan_##offset,	\
		   NULL);						\
static DEVICE_ATTR(fan##offset##_min, S_IRUGO | S_IWUSR,		\
		   show_fan_##offset##_min, set_fan_##offset##_min);	\
static DEVICE_ATTR(fan##offset##_div, S_IRUGO | S_IWUSR,		\
		   show_fan_##offset##_div, set_fan_##offset##_div);	\
static DEVICE_ATTR(auto_fan##offset##_min_pwm, S_IRUGO | S_IWUSR,	\
		   show_pwm_##offset, set_pwm_##offset)

fan_offset(1);
fan_offset(2);


/* Temps */
static ssize_t show_temp(struct device *dev, char *buf, int nr)
{
	struct adm1031_data *data = adm1031_update_device(dev);
	int ext;
	ext = nr == 0 ?
	    ((data->ext_temp[nr] >> 6) & 0x3) * 2 :
	    (((data->ext_temp[nr] >> ((nr - 1) * 3)) & 7));
	return sprintf(buf, "%d\n", TEMP_FROM_REG_EXT(data->temp[nr], ext));
}
static ssize_t show_temp_min(struct device *dev, char *buf, int nr)
{
	struct adm1031_data *data = adm1031_update_device(dev);
	return sprintf(buf, "%d\n", TEMP_FROM_REG(data->temp_min[nr]));
}
static ssize_t show_temp_max(struct device *dev, char *buf, int nr)
{
	struct adm1031_data *data = adm1031_update_device(dev);
	return sprintf(buf, "%d\n", TEMP_FROM_REG(data->temp_max[nr]));
}
static ssize_t show_temp_crit(struct device *dev, char *buf, int nr)
{
	struct adm1031_data *data = adm1031_update_device(dev);
	return sprintf(buf, "%d\n", TEMP_FROM_REG(data->temp_crit[nr]));
}
static ssize_t
set_temp_min(struct device *dev, const char *buf, size_t count, int nr)
{
	struct i2c_client *client = to_i2c_client(dev);
	struct adm1031_data *data = i2c_get_clientdata(client);
	int val;

	val = simple_strtol(buf, NULL, 10);
	val = SENSORS_LIMIT(val, -55000, nr == 0 ? 127750 : 127875);
	down(&data->update_lock);
	data->temp_min[nr] = TEMP_TO_REG(val);
	adm1031_write_value(client, ADM1031_REG_TEMP_MIN(nr),
			    data->temp_min[nr]);
	up(&data->update_lock);
	return count;
}
static ssize_t
set_temp_max(struct device *dev, const char *buf, size_t count, int nr)
{
	struct i2c_client *client = to_i2c_client(dev);
	struct adm1031_data *data = i2c_get_clientdata(client);
	int val;

	val = simple_strtol(buf, NULL, 10);
	val = SENSORS_LIMIT(val, -55000, nr == 0 ? 127750 : 127875);
	down(&data->update_lock);
	data->temp_max[nr] = TEMP_TO_REG(val);
	adm1031_write_value(client, ADM1031_REG_TEMP_MAX(nr),
			    data->temp_max[nr]);
	up(&data->update_lock);
	return count;
}
static ssize_t
set_temp_crit(struct device *dev, const char *buf, size_t count, int nr)
{
	struct i2c_client *client = to_i2c_client(dev);
	struct adm1031_data *data = i2c_get_clientdata(client);
	int val;

	val = simple_strtol(buf, NULL, 10);
	val = SENSORS_LIMIT(val, -55000, nr == 0 ? 127750 : 127875);
	down(&data->update_lock);
	data->temp_crit[nr] = TEMP_TO_REG(val);
	adm1031_write_value(client, ADM1031_REG_TEMP_CRIT(nr),
			    data->temp_crit[nr]);
	up(&data->update_lock);
	return count;
}

#define temp_reg(offset)							\
static ssize_t show_temp_##offset (struct device *dev, struct device_attribute *attr, char *buf)		\
{										\
	return show_temp(dev, buf, offset - 1);				\
}										\
static ssize_t show_temp_##offset##_min (struct device *dev, struct device_attribute *attr, char *buf)		\
{										\
	return show_temp_min(dev, buf, offset - 1);				\
}										\
static ssize_t show_temp_##offset##_max (struct device *dev, struct device_attribute *attr, char *buf)		\
{										\
	return show_temp_max(dev, buf, offset - 1);				\
}										\
static ssize_t show_temp_##offset##_crit (struct device *dev, struct device_attribute *attr, char *buf)	\
{										\
	return show_temp_crit(dev, buf, offset - 1);			\
}										\
static ssize_t set_temp_##offset##_min (struct device *dev, struct device_attribute *attr,			\
					const char *buf, size_t count)		\
{										\
	return set_temp_min(dev, buf, count, offset - 1);			\
}										\
static ssize_t set_temp_##offset##_max (struct device *dev, struct device_attribute *attr,			\
					const char *buf, size_t count)		\
{										\
	return set_temp_max(dev, buf, count, offset - 1);			\
}										\
static ssize_t set_temp_##offset##_crit (struct device *dev, struct device_attribute *attr,			\
					 const char *buf, size_t count)		\
{										\
	return set_temp_crit(dev, buf, count, offset - 1);			\
}										\
static DEVICE_ATTR(temp##offset##_input, S_IRUGO, show_temp_##offset,		\
		   NULL);							\
static DEVICE_ATTR(temp##offset##_min, S_IRUGO | S_IWUSR,			\
		   show_temp_##offset##_min, set_temp_##offset##_min);		\
static DEVICE_ATTR(temp##offset##_max, S_IRUGO | S_IWUSR,			\
		   show_temp_##offset##_max, set_temp_##offset##_max);		\
static DEVICE_ATTR(temp##offset##_crit, S_IRUGO | S_IWUSR,			\
		   show_temp_##offset##_crit, set_temp_##offset##_crit)

temp_reg(1);
temp_reg(2);
temp_reg(3);

/* Alarms */
static ssize_t show_alarms(struct device *dev, struct device_attribute *attr, char *buf)
{
	struct adm1031_data *data = adm1031_update_device(dev);
	return sprintf(buf, "%d\n", data->alarm);
}

static DEVICE_ATTR(alarms, S_IRUGO, show_alarms, NULL);


static int adm1031_attach_adapter(struct i2c_adapter *adapter)
{
	if (!(adapter->class & I2C_CLASS_HWMON))
		return 0;
	return i2c_detect(adapter, &addr_data, adm1031_detect);
}

/* This function is called by i2c_detect */
static int adm1031_detect(struct i2c_adapter *adapter, int address, int kind)
{
	struct i2c_client *new_client;
	struct adm1031_data *data;
	int err = 0;
	const char *name = "";

	if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA))
		goto exit;

	if (!(data = kmalloc(sizeof(struct adm1031_data), GFP_KERNEL))) {
		err = -ENOMEM;
		goto exit;
	}
	memset(data, 0, sizeof(struct adm1031_data));

	new_client = &data->client;
	i2c_set_clientdata(new_client, data);
	new_client->addr = address;
	new_client->adapter = adapter;
	new_client->driver = &adm1031_driver;
	new_client->flags = 0;

	if (kind < 0) {
		int id, co;
		id = i2c_smbus_read_byte_data(new_client, 0x3d);
		co = i2c_smbus_read_byte_data(new_client, 0x3e);

		if (!((id == 0x31 || id == 0x30) && co == 0x41))
			goto exit_free;
		kind = (id == 0x30) ? adm1030 : adm1031;
	}

	if (kind <= 0)
		kind = adm1031;

	/* Given the detected chip type, set the chip name and the
	 * auto fan control helper table. */
	if (kind == adm1030) {
		name = "adm1030";
		data->chan_select_table = &auto_channel_select_table_adm1030;
	} else if (kind == adm1031) {
		name = "adm1031";
		data->chan_select_table = &auto_channel_select_table_adm1031;
	}
	data->chip_type = kind;

	strlcpy(new_client->name, name, I2C_NAME_SIZE);
	data->valid = 0;
	init_MUTEX(&data->update_lock);

	/* Tell the I2C layer a new client has arrived */
	if ((err = i2c_attach_client(new_client)))
		goto exit_free;

	/* Initialize the ADM1031 chip */
	adm1031_init_client(new_client);

	/* Register sysfs hooks */
	device_create_file(&new_client->dev, &dev_attr_fan1_input);
	device_create_file(&new_client->dev, &dev_attr_fan1_div);
	device_create_file(&new_client->dev, &dev_attr_fan1_min);
	device_create_file(&new_client->dev, &dev_attr_pwm1);
	device_create_file(&new_client->dev, &dev_attr_auto_fan1_channel);
	device_create_file(&new_client->dev, &dev_attr_temp1_input);
	device_create_file(&new_client->dev, &dev_attr_temp1_min);
	device_create_file(&new_client->dev, &dev_attr_temp1_max);
	device_create_file(&new_client->dev, &dev_attr_temp1_crit);
	device_create_file(&new_client->dev, &dev_attr_temp2_input);
	device_create_file(&new_client->dev, &dev_attr_temp2_min);
	device_create_file(&new_client->dev, &dev_attr_temp2_max);
	device_create_file(&new_client->dev, &dev_attr_temp2_crit);

	device_create_file(&new_client->dev, &dev_attr_auto_temp1_off);
	device_create_file(&new_client->dev, &dev_attr_auto_temp1_min);
	device_create_file(&new_client->dev, &dev_attr_auto_temp1_max);

	device_create_file(&new_client->dev, &dev_attr_auto_temp2_off);
	device_create_file(&new_client->dev, &dev_attr_auto_temp2_min);
	device_create_file(&new_client->dev, &dev_attr_auto_temp2_max);

	device_create_file(&new_client->dev, &dev_attr_auto_fan1_min_pwm);

	device_create_file(&new_client->dev, &dev_attr_alarms);

	if (kind == adm1031) {
		device_create_file(&new_client->dev, &dev_attr_fan2_input);
		device_create_file(&new_client->dev, &dev_attr_fan2_div);
		device_create_file(&new_client->dev, &dev_attr_fan2_min);
		device_create_file(&new_client->dev, &dev_attr_pwm2);
		device_create_file(&new_client->dev,
				   &dev_attr_auto_fan2_channel);
		device_create_file(&new_client->dev, &dev_attr_temp3_input);
		device_create_file(&new_client->dev, &dev_attr_temp3_min);
		device_create_file(&new_client->dev, &dev_attr_temp3_max);
		device_create_file(&new_client->dev, &dev_attr_temp3_crit);
		device_create_file(&new_client->dev, &dev_attr_auto_temp3_off);
		device_create_file(&new_client->dev, &dev_attr_auto_temp3_min);
		device_create_file(&new_client->dev, &dev_attr_auto_temp3_max);
		device_create_file(&new_client->dev, &dev_attr_auto_fan2_min_pwm);
	}

	return 0;

exit_free:
	kfree(new_client);
exit:
	return err;
}

static int adm1031_detach_client(struct i2c_client *client)
{
	int ret;
	if ((ret = i2c_detach_client(client)) != 0) {
		return ret;
	}
	kfree(client);
	return 0;
}

static void adm1031_init_client(struct i2c_client *client)
{
	unsigned int read_val;
	unsigned int mask;
	struct adm1031_data *data = i2c_get_clientdata(client);

	mask = (ADM1031_CONF2_PWM1_ENABLE | ADM1031_CONF2_TACH1_ENABLE);
	if (data->chip_type == adm1031) {
		mask |= (ADM1031_CONF2_PWM2_ENABLE |
			ADM1031_CONF2_TACH2_ENABLE);
	} 
	/* Initialize the ADM1031 chip (enables fan speed reading ) */
	read_val = adm1031_read_value(client, ADM1031_REG_CONF2);
	if ((read_val | mask) != read_val) {
	    adm1031_write_value(client, ADM1031_REG_CONF2, read_val | mask);
	}

	read_val = adm1031_read_value(client, ADM1031_REG_CONF1);
	if ((read_val | ADM1031_CONF1_MONITOR_ENABLE) != read_val) {
	    adm1031_write_value(client, ADM1031_REG_CONF1, read_val |
				ADM1031_CONF1_MONITOR_ENABLE);
	}

}

static struct adm1031_data *adm1031_update_device(struct device *dev)
{
	struct i2c_client *client = to_i2c_client(dev);
	struct adm1031_data *data = i2c_get_clientdata(client);
	int chan;

	down(&data->update_lock);

	if (time_after(jiffies, data->last_updated + HZ + HZ / 2)
	    || !data->valid) {

		dev_dbg(&client->dev, "Starting adm1031 update\n");
		for (chan = 0;
		     chan < ((data->chip_type == adm1031) ? 3 : 2); chan++) {
			u8 oldh, newh;

			oldh =
			    adm1031_read_value(client, ADM1031_REG_TEMP(chan));
			data->ext_temp[chan] =
			    adm1031_read_value(client, ADM1031_REG_EXT_TEMP);
			newh =
			    adm1031_read_value(client, ADM1031_REG_TEMP(chan));
			if (newh != oldh) {
				data->ext_temp[chan] =
				    adm1031_read_value(client,
						       ADM1031_REG_EXT_TEMP);
#ifdef DEBUG
				oldh =
				    adm1031_read_value(client,
						       ADM1031_REG_TEMP(chan));

				/* oldh is actually newer */
				if (newh != oldh)
					dev_warn(&client->dev,
						 "Remote temperature may be "
						 "wrong.\n");
#endif
			}
			data->temp[chan] = newh;

			data->temp_min[chan] =
			    adm1031_read_value(client,
					       ADM1031_REG_TEMP_MIN(chan));
			data->temp_max[chan] =
			    adm1031_read_value(client,
					       ADM1031_REG_TEMP_MAX(chan));
			data->temp_crit[chan] =
			    adm1031_read_value(client,
					       ADM1031_REG_TEMP_CRIT(chan));
			data->auto_temp[chan] =
			    adm1031_read_value(client,
					       ADM1031_REG_AUTO_TEMP(chan));

		}

		data->conf1 = adm1031_read_value(client, ADM1031_REG_CONF1);
		data->conf2 = adm1031_read_value(client, ADM1031_REG_CONF2);

		data->alarm = adm1031_read_value(client, ADM1031_REG_STATUS(0))
			     | (adm1031_read_value(client, ADM1031_REG_STATUS(1))
				<< 8);
		if (data->chip_type == adm1030) {
			data->alarm &= 0xc0ff;
		}
		
		for (chan=0; chan<(data->chip_type == adm1030 ? 1 : 2); chan++) {
			data->fan_div[chan] =
			    adm1031_read_value(client, ADM1031_REG_FAN_DIV(chan));
			data->fan_min[chan] =
			    adm1031_read_value(client, ADM1031_REG_FAN_MIN(chan));
			data->fan[chan] =
			    adm1031_read_value(client, ADM1031_REG_FAN_SPEED(chan));
			data->pwm[chan] =
			    0xf & (adm1031_read_value(client, ADM1031_REG_PWM) >> 
				   (4*chan));
		}
		data->last_updated = jiffies;
		data->valid = 1;
	}

	up(&data->update_lock);

	return data;
}

static int __init sensors_adm1031_init(void)
{
	return i2c_add_driver(&adm1031_driver);
}

static void __exit sensors_adm1031_exit(void)
{
	i2c_del_driver(&adm1031_driver);
}

MODULE_AUTHOR("Alexandre d'Alton <alex@alexdalton.org>");
MODULE_DESCRIPTION("ADM1031/ADM1030 driver");
MODULE_LICENSE("GPL");

module_init(sensors_adm1031_init);
module_exit(sensors_adm1031_exit);