drivers/leds/leds-lp5521.c: adjust delays and add comments to them
Delays were little bit too long. Adjust delay times and add some comments
to them.
Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
diff --git a/drivers/leds/leds-lp5521.c b/drivers/leds/leds-lp5521.c
index fe69e52..963c014b 100644
--- a/drivers/leds/leds-lp5521.c
+++ b/drivers/leds/leds-lp5521.c
@@ -196,14 +196,17 @@
/* move current engine to direct mode and remember the state */
ret = lp5521_set_engine_mode(eng, LP5521_CMD_DIRECT);
- usleep_range(1000, 10000);
+ /* Mode change requires min 500 us delay. 1 - 2 ms with margin */
+ usleep_range(1000, 2000);
ret |= lp5521_read(client, LP5521_REG_OP_MODE, &mode);
/* For loading, all the engines to load mode */
lp5521_write(client, LP5521_REG_OP_MODE, LP5521_CMD_DIRECT);
- usleep_range(1000, 10000);
+ /* Mode change requires min 500 us delay. 1 - 2 ms with margin */
+ usleep_range(1000, 2000);
lp5521_write(client, LP5521_REG_OP_MODE, LP5521_CMD_LOAD);
- usleep_range(1000, 10000);
+ /* Mode change requires min 500 us delay. 1 - 2 ms with margin */
+ usleep_range(1000, 2000);
addr = LP5521_PROG_MEM_BASE + eng->prog_page * LP5521_PROG_MEM_SIZE;
i2c_smbus_write_i2c_block_data(client,
@@ -244,7 +247,10 @@
lp5521_write(client, LP5521_REG_RESET, 0xff);
- usleep_range(10000, 20000);
+ usleep_range(10000, 20000); /*
+ * Exact value is not available. 10 - 20ms
+ * appears to be enough for reset.
+ */
/* Set all PWMs to direct control mode */
ret = lp5521_write(client, LP5521_REG_OP_MODE, 0x3F);
@@ -262,8 +268,8 @@
ret |= lp5521_write(client, LP5521_REG_ENABLE,
LP5521_MASTER_ENABLE | LP5521_LOGARITHMIC_PWM |
LP5521_EXEC_RUN);
- /* enable takes 500us */
- usleep_range(500, 20000);
+ /* enable takes 500us. 1 - 2 ms leaves some margin */
+ usleep_range(1000, 2000);
return ret;
}
@@ -316,7 +322,8 @@
LP5521_MASTER_ENABLE | LP5521_LOGARITHMIC_PWM);
if (ret)
return ret;
- usleep_range(1000, 10000);
+ /* enable takes 500us. 1 - 2 ms leaves some margin */
+ usleep_range(1000, 2000);
ret = lp5521_read(client, LP5521_REG_ENABLE, &buf);
if (ret)
return ret;
@@ -704,9 +711,9 @@
if (pdata->enable) {
pdata->enable(0);
- usleep_range(1000, 10000);
+ usleep_range(1000, 2000); /* Keep enable down at least 1ms */
pdata->enable(1);
- usleep_range(1000, 10000); /* Spec says min 500us */
+ usleep_range(1000, 2000); /* 500us abs min. */
}
ret = lp5521_detect(client);