Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/v4l-dvb
* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/v4l-dvb:
V4L/DVB (6028): Turn an unnecessary mdelay() into msleep().
V4L/DVB (6027): Get rid of an ill-behaved msleep in i2c write
V4L/DVB (6026): Avoid powering up the camera on resume
V4L/DVB (6016): get_dvb_firmware: update script for new location of tda10046 firmware
V4L/DVB (5991): dvb-pll: Set minimum and maximum frequency properly
V4L/DVB (5969): ivtv: report ivtv version in status log
V4L/DVB (5967): ivtv: fix VIDIOC_S_FBUF:new OSD values where never set
V4L/DVB (5968): videodev2.h: remove superfluous FBUF GLOBAL_INV_ALPHA support
diff --git a/arch/powerpc/boot/dts/mpc8544ds.dts b/arch/powerpc/boot/dts/mpc8544ds.dts
index 4680e20..3e79bf0 100644
--- a/arch/powerpc/boot/dts/mpc8544ds.dts
+++ b/arch/powerpc/boot/dts/mpc8544ds.dts
@@ -44,8 +44,18 @@
#size-cells = <1>;
#interrupt-cells = <2>;
device_type = "soc";
- ranges = <0 e0000000 00100000>;
- reg = <e0000000 00100000>; // CCSRBAR 1M
+
+
+ ranges = <00001000 e0001000 000ff000
+ 80000000 80000000 20000000
+ a0000000 a0000000 10000000
+ b0000000 b0000000 00100000
+ c0000000 c0000000 20000000
+ b0100000 b0100000 00100000
+ e1000000 e1000000 00010000
+ e1010000 e1010000 00010000
+ e1020000 e1020000 00010000>;
+ reg = <e0000000 00001000>; // CCSRBAR 1M
bus-frequency = <0>; // Filled out by uboot.
memory-controller@2000 {
@@ -161,8 +171,8 @@
interrupt-parent = <&mpic>;
interrupts = <18 2>;
bus-range = <0 ff>;
- ranges = <02000000 0 80000000 80000000 0 10000000
- 01000000 0 00000000 e2000000 0 00800000>;
+ ranges = <02000000 0 c0000000 c0000000 0 20000000
+ 01000000 0 00000000 e1000000 0 00010000>;
clock-frequency = <3f940aa>;
#interrupt-cells = <1>;
#size-cells = <2>;
@@ -178,8 +188,8 @@
#address-cells = <3>;
reg = <9000 1000>;
bus-range = <0 ff>;
- ranges = <02000000 0 90000000 90000000 0 10000000
- 01000000 0 00000000 e3000000 0 00800000>;
+ ranges = <02000000 0 80000000 80000000 0 20000000
+ 01000000 0 00000000 e1010000 0 00010000>;
clock-frequency = <1fca055>;
interrupt-parent = <&mpic>;
interrupts = <1a 2>;
@@ -202,7 +212,7 @@
reg = <a000 1000>;
bus-range = <0 ff>;
ranges = <02000000 0 a0000000 a0000000 0 10000000
- 01000000 0 00000000 e2800000 0 00800000>;
+ 01000000 0 00000000 e1020000 0 00010000>;
clock-frequency = <1fca055>;
interrupt-parent = <&mpic>;
interrupts = <19 2>;
@@ -224,49 +234,29 @@
#address-cells = <3>;
reg = <b000 1000>;
bus-range = <0 ff>;
- ranges = <02000000 0 b0000000 b0000000 0 10000000
- 01000000 0 00000000 e3800000 0 00800000>;
+ ranges = <02000000 0 b0000000 b0000000 0 00100000
+ 01000000 0 00000000 b0100000 0 00100000>;
clock-frequency = <1fca055>;
interrupt-parent = <&mpic>;
interrupts = <1b 2>;
- interrupt-map-mask = <f800 0 0 7>;
+ interrupt-map-mask = <fb00 0 0 0>;
interrupt-map = <
-
- // IDSEL 0x1a
- d000 0 0 1 &i8259 6 2
- d000 0 0 2 &i8259 3 2
- d000 0 0 3 &i8259 4 2
- d000 0 0 4 &i8259 5 2
-
- // IDSEL 0x1b
- d800 0 0 1 &i8259 5 2
- d800 0 0 2 &i8259 0 0
- d800 0 0 3 &i8259 0 0
- d800 0 0 4 &i8259 0 0
-
// IDSEL 0x1c USB
- e000 0 0 1 &i8259 9 2
- e000 0 0 2 &i8259 a 2
- e000 0 0 3 &i8259 c 2
- e000 0 0 4 &i8259 7 2
+ e000 0 0 0 &i8259 c 2
+ e100 0 0 0 &i8259 9 2
+ e200 0 0 0 &i8259 a 2
+ e300 0 0 0 &i8259 b 2
// IDSEL 0x1d Audio
- e800 0 0 1 &i8259 9 2
- e800 0 0 2 &i8259 a 2
- e800 0 0 3 &i8259 b 2
- e800 0 0 4 &i8259 0 0
+ e800 0 0 0 &i8259 6 2
// IDSEL 0x1e Legacy
- f000 0 0 1 &i8259 c 2
- f000 0 0 2 &i8259 0 0
- f000 0 0 3 &i8259 0 0
- f000 0 0 4 &i8259 0 0
+ f000 0 0 0 &i8259 7 2
+ f100 0 0 0 &i8259 7 2
// IDSEL 0x1f IDE/SATA
- f800 0 0 1 &i8259 6 2
- f800 0 0 2 &i8259 0 0
- f800 0 0 3 &i8259 0 0
- f800 0 0 4 &i8259 0 0
+ f800 0 0 0 &i8259 e 2
+ f900 0 0 0 &i8259 5 2
>;
uli1575@0 {
reg = <0 0 0 0 0>;
@@ -274,10 +264,10 @@
#address-cells = <3>;
ranges = <02000000 0 b0000000
02000000 0 b0000000
- 0 10000000
+ 0 00100000
01000000 0 00000000
01000000 0 00000000
- 0 00080000>;
+ 0 00100000>;
pci_bridge@0 {
reg = <0 0 0 0 0>;
@@ -285,10 +275,10 @@
#address-cells = <3>;
ranges = <02000000 0 b0000000
02000000 0 b0000000
- 0 20000000
+ 0 00100000
01000000 0 00000000
01000000 0 00000000
- 0 00100000>;
+ 0 00100000>;
isa@1e {
device_type = "isa";
@@ -296,7 +286,8 @@
#size-cells = <1>;
#address-cells = <2>;
reg = <f000 0 0 0 0>;
- ranges = <1 0 01000000 0 0
+ ranges = <1 0
+ 01000000 0 0
00001000>;
interrupt-parent = <&i8259>;
@@ -312,8 +303,7 @@
built-in;
compatible = "chrp,iic";
interrupts = <9 2>;
- interrupt-parent =
- <&mpic>;
+ interrupt-parent = <&mpic>;
};
i8042@60 {
@@ -321,8 +311,7 @@
#address-cells = <1>;
reg = <1 60 1 1 64 1>;
interrupts = <1 3 c 3>;
- interrupt-parent =
- <&i8259>;
+ interrupt-parent = <&i8259>;
keyboard@0 {
reg = <0>;
@@ -336,8 +325,7 @@
};
rtc@70 {
- compatible =
- "pnpPNP,b00";
+ compatible = "pnpPNP,b00";
reg = <1 70 2>;
};
diff --git a/arch/powerpc/boot/dts/mpc8641_hpcn.dts b/arch/powerpc/boot/dts/mpc8641_hpcn.dts
index 5d82709..b0166e5 100644
--- a/arch/powerpc/boot/dts/mpc8641_hpcn.dts
+++ b/arch/powerpc/boot/dts/mpc8641_hpcn.dts
@@ -224,98 +224,36 @@
clock-frequency = <1fca055>;
interrupt-parent = <&mpic>;
interrupts = <18 2>;
- interrupt-map-mask = <f800 0 0 7>;
+ interrupt-map-mask = <fb00 0 0 0>;
interrupt-map = <
/* IDSEL 0x11 */
- 8800 0 0 1 &i8259 3 2
- 8800 0 0 2 &i8259 4 2
- 8800 0 0 3 &i8259 5 2
- 8800 0 0 4 &i8259 6 2
+ 8800 0 0 1 &i8259 9 2
+ 8800 0 0 2 &i8259 a 2
+ 8800 0 0 3 &i8259 b 2
+ 8800 0 0 4 &i8259 c 2
/* IDSEL 0x12 */
- 9000 0 0 1 &i8259 4 2
- 9000 0 0 2 &i8259 5 2
- 9000 0 0 3 &i8259 6 2
- 9000 0 0 4 &i8259 3 2
+ 9000 0 0 1 &i8259 a 2
+ 9000 0 0 2 &i8259 b 2
+ 9000 0 0 3 &i8259 c 2
+ 9000 0 0 4 &i8259 9 2
- /* IDSEL 0x13 */
- 9800 0 0 1 &i8259 0 0
- 9800 0 0 2 &i8259 0 0
- 9800 0 0 3 &i8259 0 0
- 9800 0 0 4 &i8259 0 0
+ // IDSEL 0x1c USB
+ e000 0 0 0 &i8259 c 2
+ e100 0 0 0 &i8259 9 2
+ e200 0 0 0 &i8259 a 2
+ e300 0 0 0 &i8259 b 2
- /* IDSEL 0x14 */
- a000 0 0 1 &i8259 0 0
- a000 0 0 2 &i8259 0 0
- a000 0 0 3 &i8259 0 0
- a000 0 0 4 &i8259 0 0
+ // IDSEL 0x1d Audio
+ e800 0 0 0 &i8259 6 2
- /* IDSEL 0x15 */
- a800 0 0 1 &i8259 0 0
- a800 0 0 2 &i8259 0 0
- a800 0 0 3 &i8259 0 0
- a800 0 0 4 &i8259 0 0
+ // IDSEL 0x1e Legacy
+ f000 0 0 0 &i8259 7 2
+ f100 0 0 0 &i8259 7 2
- /* IDSEL 0x16 */
- b000 0 0 1 &i8259 0 0
- b000 0 0 2 &i8259 0 0
- b000 0 0 3 &i8259 0 0
- b000 0 0 4 &i8259 0 0
-
- /* IDSEL 0x17 */
- b800 0 0 1 &i8259 0 0
- b800 0 0 2 &i8259 0 0
- b800 0 0 3 &i8259 0 0
- b800 0 0 4 &i8259 0 0
-
- /* IDSEL 0x18 */
- c000 0 0 1 &i8259 0 0
- c000 0 0 2 &i8259 0 0
- c000 0 0 3 &i8259 0 0
- c000 0 0 4 &i8259 0 0
-
- /* IDSEL 0x19 */
- c800 0 0 1 &i8259 0 0
- c800 0 0 2 &i8259 0 0
- c800 0 0 3 &i8259 0 0
- c800 0 0 4 &i8259 0 0
-
- /* IDSEL 0x1a */
- d000 0 0 1 &i8259 6 2
- d000 0 0 2 &i8259 3 2
- d000 0 0 3 &i8259 4 2
- d000 0 0 4 &i8259 5 2
-
-
- /* IDSEL 0x1b */
- d800 0 0 1 &i8259 5 2
- d800 0 0 2 &i8259 0 0
- d800 0 0 3 &i8259 0 0
- d800 0 0 4 &i8259 0 0
-
- /* IDSEL 0x1c */
- e000 0 0 1 &i8259 9 2
- e000 0 0 2 &i8259 a 2
- e000 0 0 3 &i8259 c 2
- e000 0 0 4 &i8259 7 2
-
- /* IDSEL 0x1d */
- e800 0 0 1 &i8259 9 2
- e800 0 0 2 &i8259 a 2
- e800 0 0 3 &i8259 b 2
- e800 0 0 4 &i8259 0 0
-
- /* IDSEL 0x1e */
- f000 0 0 1 &i8259 c 2
- f000 0 0 2 &i8259 0 0
- f000 0 0 3 &i8259 0 0
- f000 0 0 4 &i8259 0 0
-
- /* IDSEL 0x1f */
- f800 0 0 1 &i8259 6 2
- f800 0 0 2 &i8259 0 0
- f800 0 0 3 &i8259 0 0
- f800 0 0 4 &i8259 0 0
+ // IDSEL 0x1f IDE/SATA
+ f800 0 0 0 &i8259 e 2
+ f900 0 0 0 &i8259 5 2
>;
uli1575@0 {
reg = <0 0 0 0 0>;
diff --git a/arch/powerpc/kernel/traps.c b/arch/powerpc/kernel/traps.c
index 2bb1cb9..d8502e3 100644
--- a/arch/powerpc/kernel/traps.c
+++ b/arch/powerpc/kernel/traps.c
@@ -299,7 +299,7 @@
#ifndef CONFIG_FSL_BOOKE
#define get_mc_reason(regs) ((regs)->dsisr)
#else
-#define get_mc_reason(regs) (mfspr(SPRN_MCSR))
+#define get_mc_reason(regs) (mfspr(SPRN_MCSR) & MCSR_MASK)
#endif
#define REASON_FP ESR_FP
#define REASON_ILLEGAL (ESR_PIL | ESR_PUO)
@@ -414,8 +414,6 @@
printk("Data Cache Push Parity Error\n");
if (reason & MCSR_DCPERR)
printk("Data Cache Parity Error\n");
- if (reason & MCSR_GL_CI)
- printk("Guarded Load or Cache-Inhibited stwcx.\n");
if (reason & MCSR_BUS_IAERR)
printk("Bus - Instruction Address Error\n");
if (reason & MCSR_BUS_RAERR)
diff --git a/arch/powerpc/platforms/85xx/Kconfig b/arch/powerpc/platforms/85xx/Kconfig
index f581840..f620171 100644
--- a/arch/powerpc/platforms/85xx/Kconfig
+++ b/arch/powerpc/platforms/85xx/Kconfig
@@ -33,6 +33,7 @@
bool "Freescale MPC8544 DS"
select PPC_I8259
select DEFAULT_UIMAGE
+ select FSL_ULI1575
help
This option enables support for the MPC8544 DS board
diff --git a/arch/powerpc/platforms/85xx/mpc8544_ds.c b/arch/powerpc/platforms/85xx/mpc8544_ds.c
index 4905f6f..0f834d8 100644
--- a/arch/powerpc/platforms/85xx/mpc8544_ds.c
+++ b/arch/powerpc/platforms/85xx/mpc8544_ds.c
@@ -114,211 +114,25 @@
}
#ifdef CONFIG_PCI
-enum pirq { PIRQA = 8, PIRQB, PIRQC, PIRQD, PIRQE, PIRQF, PIRQG, PIRQH };
+extern int uses_fsl_uli_m1575;
+extern int uli_exclude_device(struct pci_controller *hose,
+ u_char bus, u_char devfn);
-/*
- * Value in table -- IRQ number
- */
-const unsigned char uli1575_irq_route_table[16] = {
- 0, /* 0: Reserved */
- 0x8,
- 0, /* 2: Reserved */
- 0x2,
- 0x4,
- 0x5,
- 0x7,
- 0x6,
- 0, /* 8: Reserved */
- 0x1,
- 0x3,
- 0x9,
- 0xb,
- 0, /* 13: Reserved */
- 0xd,
- 0xf,
-};
-
-static int __devinit
-get_pci_irq_from_of(struct pci_controller *hose, int slot, int pin)
+static int mpc85xx_exclude_device(struct pci_controller *hose,
+ u_char bus, u_char devfn)
{
- struct of_irq oirq;
- u32 laddr[3];
- struct device_node *hosenode = hose ? hose->arch_data : NULL;
+ struct device_node* node;
+ struct resource rsrc;
- if (!hosenode)
- return -EINVAL;
+ node = (struct device_node *)hose->arch_data;
+ of_address_to_resource(node, 0, &rsrc);
- laddr[0] = (hose->first_busno << 16) | (PCI_DEVFN(slot, 0) << 8);
- laddr[1] = laddr[2] = 0;
- of_irq_map_raw(hosenode, &pin, 1, laddr, &oirq);
- DBG("mpc8544_ds: pci irq addr %x, slot %d, pin %d, irq %d\n",
- laddr[0], slot, pin, oirq.specifier[0]);
- return oirq.specifier[0];
+ if ((rsrc.start & 0xfffff) == 0xb000) {
+ return uli_exclude_device(hose, bus, devfn);
+ }
+
+ return PCIBIOS_SUCCESSFUL;
}
-
-/*8259*/
-static void __devinit quirk_uli1575(struct pci_dev *dev)
-{
- unsigned short temp;
- struct pci_controller *hose = pci_bus_to_host(dev->bus);
- unsigned char irq2pin[16];
- unsigned long pirq_map_word = 0;
- u32 irq;
- int i;
-
- /*
- * ULI1575 interrupts route setup
- */
- memset(irq2pin, 0, 16); /* Initialize default value 0 */
-
- irq2pin[6]=PIRQA+3; /* enabled mapping for IRQ6 to PIRQD, used by SATA */
-
- /*
- * PIRQE -> PIRQF mapping set manually
- *
- * IRQ pin IRQ#
- * PIRQE ---- 9
- * PIRQF ---- 10
- * PIRQG ---- 11
- * PIRQH ---- 12
- */
- for (i = 0; i < 4; i++)
- irq2pin[i + 9] = PIRQE + i;
-
- /* Set IRQ-PIRQ Mapping to ULI1575 */
- for (i = 0; i < 16; i++)
- if (irq2pin[i])
- pirq_map_word |= (uli1575_irq_route_table[i] & 0xf)
- << ((irq2pin[i] - PIRQA) * 4);
-
- pirq_map_word |= 1<<26; /* disable INTx in EP mode*/
-
- /* ULI1575 IRQ mapping conf register default value is 0xb9317542 */
- DBG("Setup ULI1575 IRQ mapping configuration register value = 0x%x\n",
- (int)pirq_map_word);
- pci_write_config_dword(dev, 0x48, pirq_map_word);
-
-#define ULI1575_SET_DEV_IRQ(slot, pin, reg) \
- do { \
- int irq; \
- irq = get_pci_irq_from_of(hose, slot, pin); \
- if (irq > 0 && irq < 16) \
- pci_write_config_byte(dev, reg, irq2pin[irq]); \
- else \
- printk(KERN_WARNING "ULI1575 device" \
- "(slot %d, pin %d) irq %d is invalid.\n", \
- slot, pin, irq); \
- } while(0)
-
- /* USB 1.1 OHCI controller 1, slot 28, pin 1 */
- ULI1575_SET_DEV_IRQ(28, 1, 0x86);
-
- /* USB 1.1 OHCI controller 2, slot 28, pin 2 */
- ULI1575_SET_DEV_IRQ(28, 2, 0x87);
-
- /* USB 1.1 OHCI controller 3, slot 28, pin 3 */
- ULI1575_SET_DEV_IRQ(28, 3, 0x88);
-
- /* USB 2.0 controller, slot 28, pin 4 */
- irq = get_pci_irq_from_of(hose, 28, 4);
- if (irq >= 0 && irq <= 15)
- pci_write_config_dword(dev, 0x74, uli1575_irq_route_table[irq]);
-
- /* Audio controller, slot 29, pin 1 */
- ULI1575_SET_DEV_IRQ(29, 1, 0x8a);
-
- /* Modem controller, slot 29, pin 2 */
- ULI1575_SET_DEV_IRQ(29, 2, 0x8b);
-
- /* HD audio controller, slot 29, pin 3 */
- ULI1575_SET_DEV_IRQ(29, 3, 0x8c);
-
- /* SMB interrupt: slot 30, pin 1 */
- ULI1575_SET_DEV_IRQ(30, 1, 0x8e);
-
- /* PMU ACPI SCI interrupt: slot 30, pin 2 */
- ULI1575_SET_DEV_IRQ(30, 2, 0x8f);
-
- /* Serial ATA interrupt: slot 31, pin 1 */
- ULI1575_SET_DEV_IRQ(31, 1, 0x8d);
-
- /* Primary PATA IDE IRQ: 14
- * Secondary PATA IDE IRQ: 15
- */
- pci_write_config_byte(dev, 0x44, 0x30 | uli1575_irq_route_table[14]);
- pci_write_config_byte(dev, 0x75, uli1575_irq_route_table[15]);
-
- /* Set IRQ14 and IRQ15 to legacy IRQs */
- pci_read_config_word(dev, 0x46, &temp);
- temp |= 0xc000;
- pci_write_config_word(dev, 0x46, temp);
-
- /* Set i8259 interrupt trigger
- * IRQ 3: Level
- * IRQ 4: Level
- * IRQ 5: Level
- * IRQ 6: Level
- * IRQ 7: Level
- * IRQ 9: Level
- * IRQ 10: Level
- * IRQ 11: Level
- * IRQ 12: Level
- * IRQ 14: Edge
- * IRQ 15: Edge
- */
- outb(0xfa, 0x4d0);
- outb(0x1e, 0x4d1);
-
-#undef ULI1575_SET_DEV_IRQ
-}
-
-/* SATA */
-static void __devinit quirk_uli5288(struct pci_dev *dev)
-{
- unsigned char c;
-
- pci_read_config_byte(dev, 0x83, &c);
- c |= 0x80; /* read/write lock */
- pci_write_config_byte(dev, 0x83, c);
-
- pci_write_config_byte(dev, 0x09, 0x01); /* Base class code: storage */
- pci_write_config_byte(dev, 0x0a, 0x06); /* IDE disk */
-
- pci_read_config_byte(dev, 0x83, &c);
- c &= 0x7f;
- pci_write_config_byte(dev, 0x83, c);
-
- pci_read_config_byte(dev, 0x84, &c);
- c |= 0x01; /* emulated PATA mode enabled */
- pci_write_config_byte(dev, 0x84, c);
-}
-
-/* PATA */
-static void __devinit quirk_uli5229(struct pci_dev *dev)
-{
- unsigned short temp;
- pci_write_config_word(dev, 0x04, 0x0405); /* MEM IO MSI */
- pci_read_config_word(dev, 0x4a, &temp);
- temp |= 0x1000; /* Enable Native IRQ 14/15 */
- pci_write_config_word(dev, 0x4a, temp);
-}
-
-/*Bridge*/
-static void __devinit early_uli5249(struct pci_dev *dev)
-{
- unsigned char temp;
- pci_write_config_word(dev, 0x04, 0x0007); /* mem access */
- pci_read_config_byte(dev, 0x7c, &temp);
- pci_write_config_byte(dev, 0x7c, 0x80); /* R/W lock control */
- pci_write_config_byte(dev, 0x09, 0x01); /* set as pci-pci bridge */
- pci_write_config_byte(dev, 0x7c, temp); /* restore pci bus debug control */
- dev->class |= 0x1;
-}
-
-DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_AL, 0x1575, quirk_uli1575);
-DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_AL, 0x5288, quirk_uli5288);
-DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_AL, 0x5229, quirk_uli5229);
-DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_AL, 0x5249, early_uli5249);
#endif /* CONFIG_PCI */
/*
@@ -342,6 +156,8 @@
else
fsl_add_bridge(np, 0);
}
+ uses_fsl_uli_m1575 = 1;
+ ppc_md.pci_exclude_device = mpc85xx_exclude_device;
#endif
printk("MPC8544 DS board from Freescale Semiconductor\n");
diff --git a/arch/powerpc/platforms/86xx/Kconfig b/arch/powerpc/platforms/86xx/Kconfig
index 343b76d..685b2fb 100644
--- a/arch/powerpc/platforms/86xx/Kconfig
+++ b/arch/powerpc/platforms/86xx/Kconfig
@@ -7,6 +7,7 @@
bool "Freescale MPC8641 HPCN"
select PPC_I8259
select DEFAULT_UIMAGE
+ select FSL_ULI1575
help
This option enables support for the MPC8641 HPCN board.
diff --git a/arch/powerpc/platforms/86xx/mpc86xx_hpcn.c b/arch/powerpc/platforms/86xx/mpc86xx_hpcn.c
index e9eaa07..56b27ca 100644
--- a/arch/powerpc/platforms/86xx/mpc86xx_hpcn.c
+++ b/arch/powerpc/platforms/86xx/mpc86xx_hpcn.c
@@ -107,220 +107,25 @@
}
#ifdef CONFIG_PCI
+extern int uses_fsl_uli_m1575;
+extern int uli_exclude_device(struct pci_controller *hose,
+ u_char bus, u_char devfn);
-enum pirq{PIRQA = 8, PIRQB, PIRQC, PIRQD, PIRQE, PIRQF, PIRQG, PIRQH};
-const unsigned char uli1575_irq_route_table[16] = {
- 0, /* 0: Reserved */
- 0x8, /* 1: 0b1000 */
- 0, /* 2: Reserved */
- 0x2, /* 3: 0b0010 */
- 0x4, /* 4: 0b0100 */
- 0x5, /* 5: 0b0101 */
- 0x7, /* 6: 0b0111 */
- 0x6, /* 7: 0b0110 */
- 0, /* 8: Reserved */
- 0x1, /* 9: 0b0001 */
- 0x3, /* 10: 0b0011 */
- 0x9, /* 11: 0b1001 */
- 0xb, /* 12: 0b1011 */
- 0, /* 13: Reserved */
- 0xd, /* 14, 0b1101 */
- 0xf, /* 15, 0b1111 */
-};
-
-static int __devinit
-get_pci_irq_from_of(struct pci_controller *hose, int slot, int pin)
+static int mpc86xx_exclude_device(struct pci_controller *hose,
+ u_char bus, u_char devfn)
{
- struct of_irq oirq;
- u32 laddr[3];
- struct device_node *hosenode = hose ? hose->arch_data : NULL;
+ struct device_node* node;
+ struct resource rsrc;
- if (!hosenode) return -EINVAL;
+ node = (struct device_node *)hose->arch_data;
+ of_address_to_resource(node, 0, &rsrc);
- laddr[0] = (hose->first_busno << 16) | (PCI_DEVFN(slot, 0) << 8);
- laddr[1] = laddr[2] = 0;
- of_irq_map_raw(hosenode, &pin, 1, laddr, &oirq);
- DBG("mpc86xx_hpcn: pci irq addr %x, slot %d, pin %d, irq %d\n",
- laddr[0], slot, pin, oirq.specifier[0]);
- return oirq.specifier[0];
-}
-
-static void __devinit quirk_uli1575(struct pci_dev *dev)
-{
- unsigned short temp;
- struct pci_controller *hose = pci_bus_to_host(dev->bus);
- unsigned char irq2pin[16], c;
- unsigned long pirq_map_word = 0;
- u32 irq;
- int i;
-
- /*
- * ULI1575 interrupts route setup
- */
- memset(irq2pin, 0, 16); /* Initialize default value 0 */
-
- /*
- * PIRQA -> PIRQD mapping read from OF-tree
- *
- * interrupts for PCI slot0 -- PIRQA / PIRQB / PIRQC / PIRQD
- * PCI slot1 -- PIRQB / PIRQC / PIRQD / PIRQA
- */
- for (i = 0; i < 4; i++){
- irq = get_pci_irq_from_of(hose, 17, i + 1);
- if (irq > 0 && irq < 16)
- irq2pin[irq] = PIRQA + i;
- else
- printk(KERN_WARNING "ULI1575 device"
- "(slot %d, pin %d) irq %d is invalid.\n",
- 17, i, irq);
+ if ((rsrc.start & 0xfffff) == 0x8000) {
+ return uli_exclude_device(hose, bus, devfn);
}
- /*
- * PIRQE -> PIRQF mapping set manually
- *
- * IRQ pin IRQ#
- * PIRQE ---- 9
- * PIRQF ---- 10
- * PIRQG ---- 11
- * PIRQH ---- 12
- */
- for (i = 0; i < 4; i++) irq2pin[i + 9] = PIRQE + i;
-
- /* Set IRQ-PIRQ Mapping to ULI1575 */
- for (i = 0; i < 16; i++)
- if (irq2pin[i])
- pirq_map_word |= (uli1575_irq_route_table[i] & 0xf)
- << ((irq2pin[i] - PIRQA) * 4);
-
- /* ULI1575 IRQ mapping conf register default value is 0xb9317542 */
- DBG("Setup ULI1575 IRQ mapping configuration register value = 0x%x\n",
- pirq_map_word);
- pci_write_config_dword(dev, 0x48, pirq_map_word);
-
-#define ULI1575_SET_DEV_IRQ(slot, pin, reg) \
- do { \
- int irq; \
- irq = get_pci_irq_from_of(hose, slot, pin); \
- if (irq > 0 && irq < 16) \
- pci_write_config_byte(dev, reg, irq2pin[irq]); \
- else \
- printk(KERN_WARNING "ULI1575 device" \
- "(slot %d, pin %d) irq %d is invalid.\n", \
- slot, pin, irq); \
- } while(0)
-
- /* USB 1.1 OHCI controller 1, slot 28, pin 1 */
- ULI1575_SET_DEV_IRQ(28, 1, 0x86);
-
- /* USB 1.1 OHCI controller 2, slot 28, pin 2 */
- ULI1575_SET_DEV_IRQ(28, 2, 0x87);
-
- /* USB 1.1 OHCI controller 3, slot 28, pin 3 */
- ULI1575_SET_DEV_IRQ(28, 3, 0x88);
-
- /* USB 2.0 controller, slot 28, pin 4 */
- irq = get_pci_irq_from_of(hose, 28, 4);
- if (irq >= 0 && irq <=15)
- pci_write_config_dword(dev, 0x74, uli1575_irq_route_table[irq]);
-
- /* Audio controller, slot 29, pin 1 */
- ULI1575_SET_DEV_IRQ(29, 1, 0x8a);
-
- /* Modem controller, slot 29, pin 2 */
- ULI1575_SET_DEV_IRQ(29, 2, 0x8b);
-
- /* HD audio controller, slot 29, pin 3 */
- ULI1575_SET_DEV_IRQ(29, 3, 0x8c);
-
- /* SMB interrupt: slot 30, pin 1 */
- ULI1575_SET_DEV_IRQ(30, 1, 0x8e);
-
- /* PMU ACPI SCI interrupt: slot 30, pin 2 */
- ULI1575_SET_DEV_IRQ(30, 2, 0x8f);
-
- /* Serial ATA interrupt: slot 31, pin 1 */
- ULI1575_SET_DEV_IRQ(31, 1, 0x8d);
-
- /* Primary PATA IDE IRQ: 14
- * Secondary PATA IDE IRQ: 15
- */
- pci_write_config_byte(dev, 0x44, 0x30 | uli1575_irq_route_table[14]);
- pci_write_config_byte(dev, 0x75, uli1575_irq_route_table[15]);
-
- /* Set IRQ14 and IRQ15 to legacy IRQs */
- pci_read_config_word(dev, 0x46, &temp);
- temp |= 0xc000;
- pci_write_config_word(dev, 0x46, temp);
-
- /* Set i8259 interrupt trigger
- * IRQ 3: Level
- * IRQ 4: Level
- * IRQ 5: Level
- * IRQ 6: Level
- * IRQ 7: Level
- * IRQ 9: Level
- * IRQ 10: Level
- * IRQ 11: Level
- * IRQ 12: Level
- * IRQ 14: Edge
- * IRQ 15: Edge
- */
- outb(0xfa, 0x4d0);
- outb(0x1e, 0x4d1);
-
-#undef ULI1575_SET_DEV_IRQ
-
- /* Disable the HD interface and enable the AC97 interface. */
- pci_read_config_byte(dev, 0xb8, &c);
- c &= 0x7f;
- pci_write_config_byte(dev, 0xb8, c);
+ return PCIBIOS_SUCCESSFUL;
}
-
-static void __devinit quirk_uli5288(struct pci_dev *dev)
-{
- unsigned char c;
-
- pci_read_config_byte(dev,0x83,&c);
- c |= 0x80;
- pci_write_config_byte(dev, 0x83, c);
-
- pci_write_config_byte(dev, 0x09, 0x01);
- pci_write_config_byte(dev, 0x0a, 0x06);
-
- pci_read_config_byte(dev,0x83,&c);
- c &= 0x7f;
- pci_write_config_byte(dev, 0x83, c);
-
- pci_read_config_byte(dev,0x84,&c);
- c |= 0x01;
- pci_write_config_byte(dev, 0x84, c);
-}
-
-static void __devinit quirk_uli5229(struct pci_dev *dev)
-{
- unsigned short temp;
- pci_write_config_word(dev, 0x04, 0x0405);
- dev->class &= ~0x5;
- pci_read_config_word(dev, 0x4a, &temp);
- temp |= 0x1000;
- pci_write_config_word(dev, 0x4a, temp);
-}
-
-static void __devinit early_uli5249(struct pci_dev *dev)
-{
- unsigned char temp;
- pci_write_config_word(dev, 0x04, 0x0007);
- pci_read_config_byte(dev, 0x7c, &temp);
- pci_write_config_byte(dev, 0x7c, 0x80);
- pci_write_config_byte(dev, 0x09, 0x01);
- pci_write_config_byte(dev, 0x7c, temp);
- dev->class |= 0x1;
-}
-
-DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_AL, 0x1575, quirk_uli1575);
-DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_AL, 0x5288, quirk_uli5288);
-DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_AL, 0x5229, quirk_uli5229);
-DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_AL, 0x5249, early_uli5249);
#endif /* CONFIG_PCI */
@@ -353,6 +158,9 @@
else
fsl_add_bridge(np, 0);
}
+ uses_fsl_uli_m1575 = 1;
+ ppc_md.pci_exclude_device = mpc86xx_exclude_device;
+
#endif
printk("MPC86xx HPCN board from Freescale Semiconductor\n");
diff --git a/arch/powerpc/platforms/Kconfig b/arch/powerpc/platforms/Kconfig
index 932538a..cfc2497 100644
--- a/arch/powerpc/platforms/Kconfig
+++ b/arch/powerpc/platforms/Kconfig
@@ -282,4 +282,12 @@
minor numbers are available in /proc/devices, /proc/partitions or
in /sys/block/axonram?/dev.
+config FSL_ULI1575
+ bool
+ default n
+ help
+ Supports for the ULI1575 PCIe south bridge that exists on some
+ Freescale reference boards. The boards all use the ULI in pretty
+ much the same way.
+
endmenu
diff --git a/arch/powerpc/platforms/Makefile b/arch/powerpc/platforms/Makefile
index d6e041a..d44e832 100644
--- a/arch/powerpc/platforms/Makefile
+++ b/arch/powerpc/platforms/Makefile
@@ -1,3 +1,6 @@
+
+obj-$(CONFIG_FSL_ULI1575) += fsl_uli1575.o
+
ifeq ($(CONFIG_PPC_MERGE),y)
obj-$(CONFIG_PPC_PMAC) += powermac/
else
diff --git a/arch/powerpc/platforms/fsl_uli1575.c b/arch/powerpc/platforms/fsl_uli1575.c
new file mode 100644
index 0000000..afc9141
--- /dev/null
+++ b/arch/powerpc/platforms/fsl_uli1575.c
@@ -0,0 +1,255 @@
+/*
+ * ULI M1575 setup code - specific to Freescale boards
+ *
+ * Copyright 2007 Freescale Semiconductor Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ */
+
+#include <linux/stddef.h>
+#include <linux/kernel.h>
+#include <linux/pci.h>
+#include <linux/interrupt.h>
+#include <linux/mc146818rtc.h>
+
+#include <asm/system.h>
+#include <asm/pci-bridge.h>
+
+#define ULI_PIRQA 0x08
+#define ULI_PIRQB 0x09
+#define ULI_PIRQC 0x0a
+#define ULI_PIRQD 0x0b
+#define ULI_PIRQE 0x0c
+#define ULI_PIRQF 0x0d
+#define ULI_PIRQG 0x0e
+
+#define ULI_8259_NONE 0x00
+#define ULI_8259_IRQ1 0x08
+#define ULI_8259_IRQ3 0x02
+#define ULI_8259_IRQ4 0x04
+#define ULI_8259_IRQ5 0x05
+#define ULI_8259_IRQ6 0x07
+#define ULI_8259_IRQ7 0x06
+#define ULI_8259_IRQ9 0x01
+#define ULI_8259_IRQ10 0x03
+#define ULI_8259_IRQ11 0x09
+#define ULI_8259_IRQ12 0x0b
+#define ULI_8259_IRQ14 0x0d
+#define ULI_8259_IRQ15 0x0f
+
+u8 uli_pirq_to_irq[8] = {
+ ULI_8259_IRQ9, /* PIRQA */
+ ULI_8259_IRQ10, /* PIRQB */
+ ULI_8259_IRQ11, /* PIRQC */
+ ULI_8259_IRQ12, /* PIRQD */
+ ULI_8259_IRQ5, /* PIRQE */
+ ULI_8259_IRQ6, /* PIRQF */
+ ULI_8259_IRQ7, /* PIRQG */
+ ULI_8259_NONE, /* PIRQH */
+};
+
+/* set in board code if you want this quirks to do something */
+int uses_fsl_uli_m1575;
+
+/* Bridge */
+static void __devinit early_uli5249(struct pci_dev *dev)
+{
+ unsigned char temp;
+
+ if (!uses_fsl_uli_m1575)
+ return;
+
+ pci_write_config_word(dev, PCI_COMMAND, PCI_COMMAND_IO |
+ PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER);
+
+ /* read/write lock */
+ pci_read_config_byte(dev, 0x7c, &temp);
+ pci_write_config_byte(dev, 0x7c, 0x80);
+
+ /* set as P2P bridge */
+ pci_write_config_byte(dev, PCI_CLASS_PROG, 0x01);
+ dev->class |= 0x1;
+
+ /* restore lock */
+ pci_write_config_byte(dev, 0x7c, temp);
+}
+
+
+static void __devinit quirk_uli1575(struct pci_dev *dev)
+{
+ int i;
+
+ if (!uses_fsl_uli_m1575)
+ return;
+
+ /*
+ * ULI1575 interrupts route setup
+ */
+
+ /* ULI1575 IRQ mapping conf register maps PIRQx to IRQn */
+ for (i = 0; i < 4; i++) {
+ u8 val = uli_pirq_to_irq[i*2] | (uli_pirq_to_irq[i*2+1] << 4);
+ pci_write_config_byte(dev, 0x48 + i, val);
+ }
+
+ /* USB 1.1 OHCI controller 1: dev 28, func 0 - IRQ12 */
+ pci_write_config_byte(dev, 0x86, ULI_PIRQD);
+
+ /* USB 1.1 OHCI controller 2: dev 28, func 1 - IRQ9 */
+ pci_write_config_byte(dev, 0x87, ULI_PIRQA);
+
+ /* USB 1.1 OHCI controller 3: dev 28, func 2 - IRQ10 */
+ pci_write_config_byte(dev, 0x88, ULI_PIRQB);
+
+ /* Lan controller: dev 27, func 0 - IRQ6 */
+ pci_write_config_byte(dev, 0x89, ULI_PIRQF);
+
+ /* AC97 Audio controller: dev 29, func 0 - IRQ6 */
+ pci_write_config_byte(dev, 0x8a, ULI_PIRQF);
+
+ /* Modem controller: dev 29, func 1 - IRQ6 */
+ pci_write_config_byte(dev, 0x8b, ULI_PIRQF);
+
+ /* HD Audio controller: dev 29, func 2 - IRQ6 */
+ pci_write_config_byte(dev, 0x8c, ULI_PIRQF);
+
+ /* SATA controller: dev 31, func 1 - IRQ5 */
+ pci_write_config_byte(dev, 0x8d, ULI_PIRQE);
+
+ /* SMB interrupt: dev 30, func 1 - IRQ7 */
+ pci_write_config_byte(dev, 0x8e, ULI_PIRQG);
+
+ /* PMU ACPI SCI interrupt: dev 30, func 2 - IRQ7 */
+ pci_write_config_byte(dev, 0x8f, ULI_PIRQG);
+
+ /* USB 2.0 controller: dev 28, func 3 */
+ pci_write_config_byte(dev, 0x74, ULI_8259_IRQ11);
+
+ /* Primary PATA IDE IRQ: 14
+ * Secondary PATA IDE IRQ: 15
+ */
+ pci_write_config_byte(dev, 0x44, 0x30 | ULI_8259_IRQ14);
+ pci_write_config_byte(dev, 0x75, ULI_8259_IRQ15);
+}
+
+static void __devinit quirk_final_uli1575(struct pci_dev *dev)
+{
+ /* Set i8259 interrupt trigger
+ * IRQ 3: Level
+ * IRQ 4: Level
+ * IRQ 5: Level
+ * IRQ 6: Level
+ * IRQ 7: Level
+ * IRQ 9: Level
+ * IRQ 10: Level
+ * IRQ 11: Level
+ * IRQ 12: Level
+ * IRQ 14: Edge
+ * IRQ 15: Edge
+ */
+ if (!uses_fsl_uli_m1575)
+ return;
+
+ outb(0xfa, 0x4d0);
+ outb(0x1e, 0x4d1);
+
+ /* setup RTC */
+ CMOS_WRITE(RTC_SET, RTC_CONTROL);
+ CMOS_WRITE(RTC_24H, RTC_CONTROL);
+
+ /* ensure month, date, and week alarm fields are ignored */
+ CMOS_WRITE(0, RTC_VALID);
+
+ outb_p(0x7c, 0x72);
+ outb_p(RTC_ALARM_DONT_CARE, 0x73);
+
+ outb_p(0x7d, 0x72);
+ outb_p(RTC_ALARM_DONT_CARE, 0x73);
+}
+
+/* SATA */
+static void __devinit quirk_uli5288(struct pci_dev *dev)
+{
+ unsigned char c;
+ unsigned int d;
+
+ if (!uses_fsl_uli_m1575)
+ return;
+
+ /* read/write lock */
+ pci_read_config_byte(dev, 0x83, &c);
+ pci_write_config_byte(dev, 0x83, c|0x80);
+
+ pci_read_config_dword(dev, PCI_CLASS_REVISION, &d);
+ d = (d & 0xff) | (PCI_CLASS_STORAGE_SATA_AHCI << 8);
+ pci_write_config_dword(dev, PCI_CLASS_REVISION, d);
+
+ /* restore lock */
+ pci_write_config_byte(dev, 0x83, c);
+
+ /* disable emulated PATA mode enabled */
+ pci_read_config_byte(dev, 0x84, &c);
+ pci_write_config_byte(dev, 0x84, c & ~0x01);
+}
+
+/* PATA */
+static void __devinit quirk_uli5229(struct pci_dev *dev)
+{
+ unsigned short temp;
+
+ if (!uses_fsl_uli_m1575)
+ return;
+
+ pci_write_config_word(dev, PCI_COMMAND, PCI_COMMAND_INTX_DISABLE |
+ PCI_COMMAND_MASTER | PCI_COMMAND_IO);
+
+ /* Enable Native IRQ 14/15 */
+ pci_read_config_word(dev, 0x4a, &temp);
+ pci_write_config_word(dev, 0x4a, temp | 0x1000);
+}
+
+/* We have to do a dummy read on the P2P for the RTC to work, WTF */
+static void __devinit quirk_final_uli5249(struct pci_dev *dev)
+{
+ int i;
+ u8 *dummy;
+ struct pci_bus *bus = dev->bus;
+
+ for (i = 0; i < PCI_BUS_NUM_RESOURCES; i++) {
+ if ((bus->resource[i]) &&
+ (bus->resource[i]->flags & IORESOURCE_MEM)) {
+ dummy = ioremap(bus->resource[i]->start, 0x4);
+ if (dummy) {
+ in_8(dummy);
+ iounmap(dummy);
+ }
+ break;
+ }
+ }
+}
+
+DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_AL, 0x5249, early_uli5249);
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_AL, 0x1575, quirk_uli1575);
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_AL, 0x5288, quirk_uli5288);
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_AL, 0x5229, quirk_uli5229);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_AL, 0x5249, quirk_final_uli5249);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_AL, 0x1575, quirk_final_uli1575);
+
+int uli_exclude_device(struct pci_controller *hose,
+ u_char bus, u_char devfn)
+{
+ if (bus == (hose->first_busno + 2)) {
+ /* exclude Modem controller */
+ if ((PCI_SLOT(devfn) == 29) && (PCI_FUNC(devfn) == 1))
+ return PCIBIOS_DEVICE_NOT_FOUND;
+
+ /* exclude HD Audio controller */
+ if ((PCI_SLOT(devfn) == 29) && (PCI_FUNC(devfn) == 2))
+ return PCIBIOS_DEVICE_NOT_FOUND;
+ }
+
+ return PCIBIOS_SUCCESSFUL;
+}
diff --git a/arch/powerpc/sysdev/fsl_soc.c b/arch/powerpc/sysdev/fsl_soc.c
index 727453d..1cf29c9 100644
--- a/arch/powerpc/sysdev/fsl_soc.c
+++ b/arch/powerpc/sysdev/fsl_soc.c
@@ -22,6 +22,7 @@
#include <linux/module.h>
#include <linux/device.h>
#include <linux/platform_device.h>
+#include <linux/of_platform.h>
#include <linux/phy.h>
#include <linux/fsl_devices.h>
#include <linux/fs_enet_pd.h>
diff --git a/arch/powerpc/sysdev/rtc_cmos_setup.c b/arch/powerpc/sysdev/rtc_cmos_setup.c
index e276048..0c9ac7e 100644
--- a/arch/powerpc/sysdev/rtc_cmos_setup.c
+++ b/arch/powerpc/sysdev/rtc_cmos_setup.c
@@ -20,14 +20,16 @@
{
struct device_node *np;
struct platform_device *pd;
- struct resource res;
+ struct resource res[2];
int ret;
+ memset(&res, 0, sizeof(res));
+
np = of_find_compatible_node(NULL, NULL, "pnpPNP,b00");
if (!np)
return -ENODEV;
- ret = of_address_to_resource(np, 0, &res);
+ ret = of_address_to_resource(np, 0, &res[0]);
of_node_put(np);
if (ret)
return ret;
@@ -36,11 +38,18 @@
* RTC_PORT(x) is hardcoded in asm/mc146818rtc.h. Verify that the
* address provided by the device node matches.
*/
- if (res.start != RTC_PORT(0))
+ if (res[0].start != RTC_PORT(0))
return -EINVAL;
+ /* Use a fixed interrupt value of 8 since on PPC if we are using this
+ * its off an i8259 which we ensure has interrupt numbers 0..15. */
+ res[1].start = 8;
+ res[1].end = 8;
+ res[1].flags = IORESOURCE_IRQ;
+
pd = platform_device_register_simple("rtc_cmos", -1,
- &res, 1);
+ &res[0], 2);
+
if (IS_ERR(pd))
return PTR_ERR(pd);
diff --git a/drivers/kvm/kvm_main.c b/drivers/kvm/kvm_main.c
index 9685609..cd05579 100644
--- a/drivers/kvm/kvm_main.c
+++ b/drivers/kvm/kvm_main.c
@@ -2974,6 +2974,10 @@
switch (val) {
case CPU_DYING:
case CPU_DYING_FROZEN:
+ printk(KERN_INFO "kvm: disabling virtualization on CPU%d\n",
+ cpu);
+ hardware_disable(NULL);
+ break;
case CPU_UP_CANCELED:
case CPU_UP_CANCELED_FROZEN:
printk(KERN_INFO "kvm: disabling virtualization on CPU%d\n",
diff --git a/fs/jffs2/write.c b/fs/jffs2/write.c
index bc61859..664c164 100644
--- a/fs/jffs2/write.c
+++ b/fs/jffs2/write.c
@@ -566,6 +566,9 @@
struct jffs2_full_dirent **prev = &dir_f->dents;
uint32_t nhash = full_name_hash(name, namelen);
+ /* We don't actually want to reserve any space, but we do
+ want to be holding the alloc_sem when we write to flash */
+ down(&c->alloc_sem);
down(&dir_f->sem);
while ((*prev) && (*prev)->nhash <= nhash) {
diff --git a/include/asm-powerpc/reg_booke.h b/include/asm-powerpc/reg_booke.h
index 064405c..8fdc2b4 100644
--- a/include/asm-powerpc/reg_booke.h
+++ b/include/asm-powerpc/reg_booke.h
@@ -223,7 +223,6 @@
#define MCSR_ICPERR 0x40000000UL /* I-Cache Parity Error */
#define MCSR_DCP_PERR 0x20000000UL /* D-Cache Push Parity Error */
#define MCSR_DCPERR 0x10000000UL /* D-Cache Parity Error */
-#define MCSR_GL_CI 0x00010000UL /* Guarded Load or Cache-Inhibited stwcx. */
#define MCSR_BUS_IAERR 0x00000080UL /* Instruction Address Error */
#define MCSR_BUS_RAERR 0x00000040UL /* Read Address Error */
#define MCSR_BUS_WAERR 0x00000020UL /* Write Address Error */
@@ -232,6 +231,12 @@
#define MCSR_BUS_WBERR 0x00000004UL /* Write Data Bus Error */
#define MCSR_BUS_IPERR 0x00000002UL /* Instruction parity Error */
#define MCSR_BUS_RPERR 0x00000001UL /* Read parity Error */
+
+/* e500 parts may set unused bits in MCSR; mask these off */
+#define MCSR_MASK (MCSR_MCP | MCSR_ICPERR | MCSR_DCP_PERR | \
+ MCSR_DCPERR | MCSR_BUS_IAERR | MCSR_BUS_RAERR | \
+ MCSR_BUS_WAERR | MCSR_BUS_IBERR | MCSR_BUS_RBERR | \
+ MCSR_BUS_WBERR | MCSR_BUS_IPERR | MCSR_BUS_RPERR)
#endif
#ifdef CONFIG_E200
#define MCSR_MCP 0x80000000UL /* Machine Check Input Pin */
@@ -243,6 +248,11 @@
#define MCSR_BUS_DRERR 0x00000008UL /* Read Bus Error on data load */
#define MCSR_BUS_WRERR 0x00000004UL /* Write Bus Error on buffered
store or cache line push */
+
+/* e200 parts may set unused bits in MCSR; mask these off */
+#define MCSR_MASK (MCSR_MCP | MCSR_CP_PERR | MCSR_CPERR | \
+ MCSR_EXCP_ERR | MCSR_BUS_IRERR | MCSR_BUS_DRERR | \
+ MCSR_BUS_WRERR)
#endif
/* Bit definitions for the DBSR. */
diff --git a/kernel/printk.c b/kernel/printk.c
index bd2cd06..5c7c325 100644
--- a/kernel/printk.c
+++ b/kernel/printk.c
@@ -1083,6 +1083,17 @@
}
EXPORT_SYMBOL(unregister_console);
+static int __init disable_boot_consoles(void)
+{
+ if (console_drivers->flags & CON_BOOT) {
+ printk(KERN_INFO "turn off boot console %s%d\n",
+ console_drivers->name, console_drivers->index);
+ return unregister_console(console_drivers);
+ }
+ return 0;
+}
+late_initcall(disable_boot_consoles);
+
/**
* tty_write_message - write a message to a certain tty, not just the console.
* @tty: the destination tty_struct
diff --git a/kernel/sysctl.c b/kernel/sysctl.c
index 8bdb8c0..9029690 100644
--- a/kernel/sysctl.c
+++ b/kernel/sysctl.c
@@ -27,7 +27,6 @@
#include <linux/capability.h>
#include <linux/ctype.h>
#include <linux/utsname.h>
-#include <linux/capability.h>
#include <linux/smp_lock.h>
#include <linux/fs.h>
#include <linux/init.h>
diff --git a/net/bridge/br_sysfs_br.c b/net/bridge/br_sysfs_br.c
index 88f4300..c65f54e 100644
--- a/net/bridge/br_sysfs_br.c
+++ b/net/bridge/br_sysfs_br.c
@@ -167,6 +167,7 @@
br_stp_set_enabled(br, val);
rtnl_unlock();
+ return len;
}
static DEVICE_ATTR(stp_state, S_IRUGO | S_IWUSR, show_stp_state,
store_stp_state);