ARM: dts: msm: Enable camera on MSM8937 MTP
Add device node entries to enable camera
sensors on msm8937 mtp.
It is a snapshot of msm8937 device node from
msm-3.18 at commit 71105998845fb ("ALSA: seq: Fix
use-after-free at creating a port").
Change-Id: I61caa7e4a6269130383e3a896c920b98e33513fd
Signed-off-by: Vijay kumar Tumati <vtumati@codeaurora.org>
diff --git a/arch/arm64/boot/dts/qcom/msm8937-camera-sensor-mtp.dtsi b/arch/arm64/boot/dts/qcom/msm8937-camera-sensor-mtp.dtsi
new file mode 100644
index 0000000..e7a5822
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/msm8937-camera-sensor-mtp.dtsi
@@ -0,0 +1,283 @@
+/*
+ * Copyright (c) 2015-2016, 2018, The Linux Foundation. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 and
+ * only version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+&cci {
+ actuator0: qcom,actuator@0 {
+ cell-index = <0>;
+ reg = <0x0>;
+ compatible = "qcom,actuator";
+ qcom,cci-master = <0>;
+ cam_vaf-supply = <&pm8937_l17>;
+ qcom,cam-vreg-name = "cam_vaf";
+ qcom,cam-vreg-min-voltage = <2850000>;
+ qcom,cam-vreg-max-voltage = <2850000>;
+ qcom,cam-vreg-op-mode = <80000>;
+ };
+
+ actuator1: qcom,actuator@1 {
+ cell-index = <1>;
+ reg = <0x1>;
+ compatible = "qcom,actuator";
+ qcom,cci-master = <0>;
+ cam_vaf-supply = <&pm8937_l17>;
+ qcom,cam-vreg-name = "cam_vaf";
+ qcom,cam-vreg-min-voltage = <2850000>;
+ qcom,cam-vreg-max-voltage = <2850000>;
+ qcom,cam-vreg-op-mode = <80000>;
+ };
+
+ eeprom0: qcom,eeprom@0 {
+ cell-index = <0>;
+ compatible = "qcom,eeprom";
+ qcom,cci-master = <0>;
+ reg = <0x0>;
+ cam_vdig-supply = <&pm8937_l23>;
+ cam_vana-supply = <&pm8937_l22>;
+ cam_vio-supply = <&pm8937_l6>;
+ cam_vaf-supply = <&pm8937_l17>;
+ qcom,cam-vreg-name = "cam_vdig", "cam_vana", "cam_vio",
+ "cam_vaf";
+ qcom,cam-vreg-min-voltage = <1200000 0 2800000 2850000>;
+ qcom,cam-vreg-max-voltage = <1200000 0 2800000 2850000>;
+ qcom,cam-vreg-op-mode = <200000 0 80000 100000>;
+ pinctrl-names = "cam_default", "cam_suspend";
+ pinctrl-0 = <&cam_sensor_mclk0_default
+ &cam_sensor_rear_default>;
+ pinctrl-1 = <&cam_sensor_mclk0_sleep &cam_sensor_rear_sleep>;
+ gpios = <&tlmm 26 0>,
+ <&tlmm 36 0>,
+ <&tlmm 35 0>;
+ qcom,gpio-reset = <1>;
+ qcom,gpio-standby = <2>;
+ qcom,gpio-req-tbl-num = <0 1 2>;
+ qcom,gpio-req-tbl-flags = <1 0 0>;
+ qcom,gpio-req-tbl-label = "CAMIF_MCLK0",
+ "CAM_RESET0",
+ "CAM_STANDBY0";
+ status = "ok";
+ clocks = <&clock_gcc clk_mclk0_clk_src>,
+ <&clock_gcc clk_gcc_camss_mclk0_clk>;
+ clock-names = "cam_src_clk", "cam_clk";
+ qcom,clock-rates = <19200000 0>;
+ };
+
+ eeprom1: qcom,eeprom@1 {
+ cell-index = <1>;
+ reg = <0x1>;
+ qcom,eeprom-name = "sunny_8865";
+ compatible = "qcom,eeprom";
+ qcom,slave-addr = <0x6c>;
+ qcom,cci-master = <0>;
+ qcom,num-blocks = <8>;
+
+ qcom,page0 = <1 0x0100 2 0x01 1 1>;
+ qcom,poll0 = <0 0x0 2 0x0 1 0>;
+ qcom,mem0 = <0 0x0 2 0x0 1 0>;
+
+ qcom,page1 = <1 0x5002 2 0x00 1 0>;
+ qcom,poll1 = <0 0x0 2 0x0 1 0>;
+ qcom,mem1 = <0 0x0 2 0x0 1 0>;
+
+ qcom,page2 = <1 0x3d84 2 0xc0 1 0>;
+ qcom,poll2 = <0 0x0 2 0x0 1 0>;
+ qcom,mem2 = <0 0x0 2 0x0 1 0>;
+
+ qcom,page3 = <1 0x3d88 2 0x70 1 0>;
+ qcom,poll3 = <0 0x0 2 0x0 1 0>;
+ qcom,mem3 = <0 0x0 2 0x0 1 0>;
+
+ qcom,page4 = <1 0x3d89 2 0x10 1 0>;
+ qcom,poll4 = <0 0x0 2 0x0 1 0>;
+ qcom,mem4 = <0 0x0 2 0x0 1 0>;
+
+ qcom,page5 = <1 0x3d8a 2 0x70 1 0>;
+ qcom,poll5 = <0 0x0 2 0x0 1 0>;
+ qcom,mem5 = <0 0x0 2 0x0 1 0>;
+
+ qcom,page6 = <1 0x3d8b 2 0xf4 1 0>;
+ qcom,poll6 = <0 0x0 2 0x0 1 0>;
+ qcom,mem6 = <0 0x0 2 0x0 1 0>;
+
+ qcom,page7 = <1 0x3d81 2 0x01 1 10>;
+ qcom,poll7 = <0 0x0 2 0x0 1 1>;
+ qcom,mem7 = <1536 0x7010 2 0 1 0>;
+
+ cam_vdig-supply = <&pm8937_l23>;
+ cam_vana-supply = <&pm8937_l22>;
+ cam_vio-supply = <&pm8937_l6>;
+ cam_vaf-supply = <&pm8937_l17>;
+ qcom,cam-vreg-name = "cam_vdig", "cam_vio", "cam_vana",
+ "cam_vaf";
+ qcom,cam-vreg-min-voltage = <1200000 0 2800000 2850000>;
+ qcom,cam-vreg-max-voltage = <1200000 0 2800000 2850000>;
+ qcom,cam-vreg-op-mode = <105000 0 80000 100000>;
+ qcom,gpio-no-mux = <0>;
+ pinctrl-names = "cam_default", "cam_suspend";
+ pinctrl-0 = <&cam_sensor_mclk2_default
+ &cam_sensor_front1_default>;
+ pinctrl-1 = <&cam_sensor_mclk2_sleep &cam_sensor_front1_sleep>;
+ gpios = <&tlmm 28 0>,
+ <&tlmm 40 0>,
+ <&tlmm 39 0>;
+ qcom,gpio-reset = <1>;
+ qcom,gpio-standby = <2>;
+ qcom,gpio-req-tbl-num = <0 1 2>;
+ qcom,gpio-req-tbl-flags = <1 0 0>;
+ qcom,gpio-req-tbl-label = "CAMIF_MCLK2",
+ "CAM_RESET2",
+ "CAM_STANDBY2";
+ qcom,cam-power-seq-type = "sensor_vreg", "sensor_vreg",
+ "sensor_vreg",
+ "sensor_gpio", "sensor_gpio" , "sensor_clk";
+ qcom,cam-power-seq-val = "cam_vdig", "cam_vana", "cam_vio",
+ "sensor_gpio_reset", "sensor_gpio_standby",
+ "sensor_cam_mclk";
+ qcom,cam-power-seq-cfg-val = <1 1 1 1 1 24000000>;
+ qcom,cam-power-seq-delay = <1 1 1 30 30 5>;
+ status = "ok";
+ clocks = <&clock_gcc clk_mclk2_clk_src>,
+ <&clock_gcc clk_gcc_camss_mclk2_clk>;
+ clock-names = "cam_src_clk", "cam_clk";
+ qcom,clock-rates = <19200000 0>;
+ };
+
+ qcom,camera@0 {
+ cell-index = <0>;
+ compatible = "qcom,camera";
+ reg = <0x0>;
+ qcom,csiphy-sd-index = <0>;
+ qcom,csid-sd-index = <0>;
+ qcom,mount-angle = <270>;
+ qcom,led-flash-src = <&led_flash0>;
+ qcom,eeprom-src = <&eeprom0>;
+ qcom,actuator-src = <&actuator0>;
+ cam_vana-supply = <&pm8937_l22>;
+ cam_vio-supply = <&pm8937_l6>;
+ cam_vaf-supply = <&pm8937_l17>;
+ qcom,cam-vreg-name = "cam_vio", "cam_vana", "cam_vaf";
+ qcom,cam-vreg-min-voltage = <0 2800000 2850000>;
+ qcom,cam-vreg-max-voltage = <0 2800000 2850000>;
+ qcom,cam-vreg-op-mode = <0 80000 100000>;
+ pinctrl-names = "cam_default", "cam_suspend";
+ pinctrl-0 = <&cam_sensor_mclk0_default
+ &cam_sensor_rear_default
+ &cam_sensor_rear_vdig>;
+ pinctrl-1 = <&cam_sensor_mclk0_sleep &cam_sensor_rear_sleep
+ &cam_sensor_rear_vdig_sleep>;
+ gpios = <&tlmm 26 0>,
+ <&tlmm 36 0>,
+ <&tlmm 35 0>,
+ <&tlmm 62 0>;
+ qcom,gpio-reset = <1>;
+ qcom,gpio-standby = <2>;
+ qcom,gpio-vdig = <3>;
+ qcom,gpio-req-tbl-num = <0 1 2 3>;
+ qcom,gpio-req-tbl-flags = <1 0 0 0>;
+ qcom,gpio-req-tbl-label = "CAMIF_MCLK0",
+ "CAM_RESET0",
+ "CAM_STANDBY0",
+ "CAM_VDIG";
+ qcom,sensor-position = <0>;
+ qcom,sensor-mode = <0>;
+ qcom,cci-master = <0>;
+ status = "ok";
+ clocks = <&clock_gcc clk_mclk0_clk_src>,
+ <&clock_gcc clk_gcc_camss_mclk0_clk>;
+ clock-names = "cam_src_clk", "cam_clk";
+ qcom,clock-rates = <24000000 0>;
+ };
+
+ qcom,camera@1 {
+ cell-index = <1>;
+ compatible = "qcom,camera";
+ reg = <0x1>;
+ qcom,csiphy-sd-index = <1>;
+ qcom,csid-sd-index = <1>;
+ qcom,mount-angle = <90>;
+ cam_vdig-supply = <&pm8937_l23>;
+ cam_vana-supply = <&pm8937_l22>;
+ cam_vio-supply = <&pm8937_l6>;
+ cam_vaf-supply = <&pm8937_l17>;
+ qcom,cam-vreg-name = "cam_vdig", "cam_vio", "cam_vana",
+ "cam_vaf";
+ qcom,cam-vreg-min-voltage = <1200000 0 2800000 2850000>;
+ qcom,cam-vreg-max-voltage = <1200000 0 2800000 2850000>;
+ qcom,cam-vreg-op-mode = <200000 0 80000 100000>;
+ pinctrl-names = "cam_default", "cam_suspend";
+ pinctrl-0 = <&cam_sensor_mclk1_default
+ &cam_sensor_front_default>;
+ pinctrl-1 = <&cam_sensor_mclk1_sleep
+ &cam_sensor_front_sleep>;
+ gpios = <&tlmm 27 0>,
+ <&tlmm 38 0>,
+ <&tlmm 50 0>;
+ qcom,gpio-reset = <1>;
+ qcom,gpio-standby = <2>;
+ qcom,gpio-req-tbl-num = <0 1 2>;
+ qcom,gpio-req-tbl-flags = <1 0 0>;
+ qcom,gpio-req-tbl-label = "CAMIF_MCLK1",
+ "CAM_RESET1",
+ "CAM_STANDBY1";
+ qcom,sensor-position = <0x100>;
+ qcom,sensor-mode = <1>;
+ qcom,cci-master = <1>;
+ clocks = <&clock_gcc clk_mclk1_clk_src>,
+ <&clock_gcc clk_gcc_camss_mclk1_clk>;
+ clock-names = "cam_src_clk", "cam_clk";
+ qcom,clock-rates = <24000000 0>;
+ };
+
+ qcom,camera@2 {
+ cell-index = <2>;
+ compatible = "qcom,camera";
+ reg = <0x02>;
+ qcom,csiphy-sd-index = <1>;
+ qcom,csid-sd-index = <1>;
+ qcom,mount-angle = <90>;
+ qcom,eeprom-src = <&eeprom1>;
+ qcom,actuator-src = <&actuator1>;
+ cam_vdig-supply = <&pm8937_l23>;
+ cam_vana-supply = <&pm8937_l22>;
+ cam_vio-supply = <&pm8937_l6>;
+ cam_vaf-supply = <&pm8937_l17>;
+ qcom,cam-vreg-name = "cam_vdig", "cam_vio", "cam_vana",
+ "cam_vaf";
+ qcom,cam-vreg-min-voltage = <1200000 0 2800000 2850000>;
+ qcom,cam-vreg-max-voltage = <1200000 0 2800000 2850000>;
+ qcom,cam-vreg-op-mode = <105000 0 80000 100000>;
+ qcom,gpio-no-mux = <0>;
+ pinctrl-names = "cam_default", "cam_suspend";
+ pinctrl-0 = <&cam_sensor_mclk2_default
+ &cam_sensor_front1_default>;
+ pinctrl-1 = <&cam_sensor_mclk2_sleep
+ &cam_sensor_front1_sleep>;
+ gpios = <&tlmm 28 0>,
+ <&tlmm 40 0>,
+ <&tlmm 39 0>;
+ qcom,gpio-reset = <1>;
+ qcom,gpio-standby = <2>;
+ qcom,gpio-req-tbl-num = <0 1 2>;
+ qcom,gpio-req-tbl-flags = <1 0 0>;
+ qcom,gpio-req-tbl-label = "CAMIF_MCLK2",
+ "CAM_RESET2",
+ "CAM_STANDBY2";
+ qcom,sensor-position = <1>;
+ qcom,sensor-mode = <0>;
+ qcom,cci-master = <0>;
+ status = "ok";
+ clocks = <&clock_gcc clk_mclk2_clk_src>,
+ <&clock_gcc clk_gcc_camss_mclk2_clk>;
+ clock-names = "cam_src_clk", "cam_clk";
+ qcom,clock-rates = <24000000 0>;
+ };
+};