blob: 8b94ca27e0700d6080f86558e2bb9497e8bbf518 [file] [log] [blame]
/*
* Copyright (c) 2016-2017, The Linux Foundation. All rights reserved.
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 and
* only version 2 as published by the Free Software Foundation.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*/
&soc {
led_flash_rear: qcom,camera-flash@0 {
cell-index = <0>;
reg = <0x00 0x00>;
compatible = "qcom,camera-flash";
flash-source = <&pm660l_flash0 &pm660l_flash1>;
torch-source = <&pm660l_torch0 &pm660l_torch1>;
switch-source = <&pm660l_switch0>;
status = "ok";
};
led_flash_front: qcom,camera-flash@1 {
cell-index = <1>;
reg = <0x01 0x00>;
compatible = "qcom,camera-flash";
flash-source = <&pm660l_flash2>;
torch-source = <&pm660l_torch2>;
switch-source = <&pm660l_switch1>;
status = "ok";
};
actuator_regulator: gpio-regulator@0 {
compatible = "regulator-fixed";
reg = <0x00 0x00>;
regulator-name = "actuator_regulator";
regulator-min-microvolt = <2800000>;
regulator-max-microvolt = <2800000>;
regulator-enable-ramp-delay = <100>;
enable-active-high;
gpio = <&tlmm 27 0>;
};
camera_ldo: gpio-regulator@2 {
compatible = "regulator-fixed";
reg = <0x02 0x00>;
regulator-name = "camera_ldo";
regulator-min-microvolt = <1352000>;
regulator-max-microvolt = <1352000>;
regulator-enable-ramp-delay = <233>;
enable-active-high;
gpio = <&pm660l_gpios 3 0>;
pinctrl-names = "default";
pinctrl-0 = <&camera_dvdd_en_default>;
vin-supply = <&pm660_s6>;
};
camera_rear_ldo: gpio-regulator@1 {
compatible = "regulator-fixed";
reg = <0x01 0x00>;
regulator-name = "camera_rear_ldo";
regulator-min-microvolt = <1352000>;
regulator-max-microvolt = <1352000>;
regulator-enable-ramp-delay = <135>;
enable-active-high;
gpio = <&pm660l_gpios 4 0>;
pinctrl-names = "default";
pinctrl-0 = <&camera_rear_dvdd_en_default>;
vin-supply = <&pm660_s6>;
};
camera_vio_ldo: gpio-regulator@3 {
compatible = "regulator-fixed";
reg = <0x03 0x00>;
regulator-name = "camera_vio_ldo";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-enable-ramp-delay = <233>;
enable-active-high;
gpio = <&tlmm 29 0>;
pinctrl-names = "default";
pinctrl-0 = <&cam_sensor_rear_vio>;
vin-supply = <&pm660_s4>;
};
camera_vana_ldo: gpio-regulator@4 {
compatible = "regulator-fixed";
reg = <0x04 0x00>;
regulator-name = "camera_vana_ldo";
regulator-min-microvolt = <2850000>;
regulator-max-microvolt = <2850000>;
regulator-enable-ramp-delay = <233>;
enable-active-high;
gpio = <&tlmm 8 0>;
pinctrl-names = "default";
pinctrl-0 = <&cam_sensor_rear_vana>;
vin-supply = <&pm660l_bob>;
};
};
&cam_cci {
qcom,cam-res-mgr {
compatible = "qcom,cam-res-mgr";
status = "ok";
};
actuator_rear: qcom,actuator@0 {
cell-index = <0>;
reg = <0x0>;
compatible = "qcom,actuator";
cci-master = <0>;
cam_vaf-supply = <&actuator_regulator>;
regulator-names = "cam_vaf";
rgltr-cntrl-support;
rgltr-min-voltage = <2800000>;
rgltr-max-voltage = <2800000>;
rgltr-load-current = <0>;
};
actuator_front: qcom,actuator@1 {
cell-index = <1>;
reg = <0x1>;
compatible = "qcom,actuator";
cci-master = <1>;
cam_vaf-supply = <&actuator_regulator>;
regulator-names = "cam_vaf";
rgltr-cntrl-support;
rgltr-min-voltage = <2800000>;
rgltr-max-voltage = <2800000>;
rgltr-load-current = <0>;
};
ois_rear: qcom,ois@0 {
cell-index = <0>;
reg = <0x0>;
compatible = "qcom,ois";
cci-master = <0>;
cam_vaf-supply = <&actuator_regulator>;
regulator-names = "cam_vaf";
rgltr-cntrl-support;
rgltr-min-voltage = <2800000>;
rgltr-max-voltage = <2800000>;
rgltr-load-current = <0>;
status = "disabled";
};
eeprom_rear: qcom,eeprom@0 {
cell-index = <0>;
reg = <0>;
compatible = "qcom,eeprom";
cam_vio-supply = <&camera_vio_ldo>;
cam_vana-supply = <&camera_vana_ldo>;
cam_vdig-supply = <&camera_rear_ldo>;
cam_clk-supply = <&titan_top_gdsc>;
cam_vaf-supply = <&actuator_regulator>;
regulator-names = "cam_vio", "cam_vana", "cam_vdig",
"cam_clk", "cam_vaf";
rgltr-cntrl-support;
rgltr-min-voltage = <1800000 2850000 1352000 0 2800000>;
rgltr-max-voltage = <1800000 2850000 1352000 0 2800000>;
rgltr-load-current = <0 80000 105000 0 0>;
gpio-no-mux = <0>;
pinctrl-names = "cam_default", "cam_suspend";
pinctrl-0 = <&cam_sensor_mclk0_active
&cam_sensor_rear_active>;
pinctrl-1 = <&cam_sensor_mclk0_suspend
&cam_sensor_rear_suspend>;
gpios = <&tlmm 13 0>,
<&tlmm 30 0>;
gpio-reset = <1>;
gpio-req-tbl-num = <0 1>;
gpio-req-tbl-flags = <1 0>;
gpio-req-tbl-label = "CAMIF_MCLK0",
"CAM_RESET0";
sensor-mode = <0>;
cci-master = <0>;
status = "ok";
clocks = <&clock_camcc CAM_CC_MCLK0_CLK>;
clock-names = "cam_clk";
clock-cntl-level = "turbo";
clock-rates = <24000000>;
};
eeprom_rear_aux: qcom,eeprom@1 {
cell-index = <1>;
reg = <0x1>;
compatible = "qcom,eeprom";
cam_vio-supply = <&camera_vio_ldo>;
cam_vana-supply = <&camera_vana_ldo>;
cam_vdig-supply = <&camera_ldo>;
cam_clk-supply = <&titan_top_gdsc>;
cam_vaf-supply = <&actuator_regulator>;
regulator-names = "cam_vdig", "cam_vio", "cam_vana",
"cam_clk", "cam_vaf";
rgltr-cntrl-support;
rgltr-min-voltage = <1352000 1800000 2850000 0 2800000>;
rgltr-max-voltage = <1352000 1800000 2850000 0 2800000>;
rgltr-load-current = <105000 0 80000 0 0>;
gpio-no-mux = <0>;
pinctrl-names = "cam_default", "cam_suspend";
pinctrl-0 = <&cam_sensor_mclk1_active
&cam_sensor_rear2_active>;
pinctrl-1 = <&cam_sensor_mclk1_suspend
&cam_sensor_rear2_suspend>;
gpios = <&tlmm 14 0>,
<&tlmm 28 0>;
gpio-reset = <1>;
gpio-req-tbl-num = <0 1>;
gpio-req-tbl-flags = <1 0>;
gpio-req-tbl-label = "CAMIF_MCLK1",
"CAM_RESET1";
sensor-position = <0>;
sensor-mode = <0>;
cci-master = <1>;
status = "ok";
clock-names = "cam_clk";
clock-cntl-level = "turbo";
clock-rates = <24000000>;
};
eeprom_front: qcom,eeprom@2 {
cell-index = <2>;
reg = <0x2>;
compatible = "qcom,eeprom";
cam_vio-supply = <&camera_vio_ldo>;
cam_vana-supply = <&camera_vana_ldo>;
cam_vdig-supply = <&camera_ldo>;
cam_clk-supply = <&titan_top_gdsc>;
cam_vaf-supply = <&actuator_regulator>;
regulator-names = "cam_vio", "cam_vana", "cam_vdig",
"cam_clk", "cam_vaf";
rgltr-cntrl-support;
rgltr-min-voltage = <1800000 2850000 1352000 0 2800000>;
rgltr-max-voltage = <1800000 2850000 1352000 0 2800000>;
rgltr-load-current = <0 80000 105000 0 0>;
gpio-no-mux = <0>;
pinctrl-names = "cam_default", "cam_suspend";
pinctrl-0 = <&cam_sensor_mclk2_active
&cam_sensor_front_active>;
pinctrl-1 = <&cam_sensor_mclk2_suspend
&cam_sensor_front_suspend>;
gpios = <&tlmm 15 0>,
<&tlmm 9 0>;
gpio-reset = <1>;
gpio-req-tbl-num = <0 1>;
gpio-req-tbl-flags = <1 0>;
gpio-req-tbl-label = "CAMIF_MCLK2",
"CAM_RESET2";
sensor-mode = <0>;
cci-master = <1>;
status = "ok";
clocks = <&clock_camcc CAM_CC_MCLK2_CLK>;
clock-names = "cam_clk";
clock-cntl-level = "turbo";
clock-rates = <24000000>;
};
qcom,cam-sensor@0 {
cell-index = <0>;
compatible = "qcom,cam-sensor";
reg = <0x0>;
csiphy-sd-index = <0>;
sensor-position-roll = <270>;
sensor-position-pitch = <0>;
sensor-position-yaw = <180>;
led-flash-src = <&led_flash_rear>;
actuator-src = <&actuator_rear>;
ois-src = <&ois_rear>;
eeprom-src = <&eeprom_rear>;
cam_vio-supply = <&camera_vio_ldo>;
cam_vana-supply = <&camera_vana_ldo>;
cam_vdig-supply = <&camera_rear_ldo>;
cam_clk-supply = <&titan_top_gdsc>;
regulator-names = "cam_vio", "cam_vana", "cam_vdig",
"cam_clk";
rgltr-cntrl-support;
rgltr-min-voltage = <1800000 2850000 1352000 0>;
rgltr-max-voltage = <1800000 2850000 1352000 0>;
rgltr-load-current = <0 80000 105000 0>;
gpio-no-mux = <0>;
pinctrl-names = "cam_default", "cam_suspend";
pinctrl-0 = <&cam_sensor_mclk0_active
&cam_sensor_rear_active>;
pinctrl-1 = <&cam_sensor_mclk0_suspend
&cam_sensor_rear_suspend>;
gpios = <&tlmm 13 0>,
<&tlmm 30 0>;
gpio-reset = <1>;
gpio-req-tbl-num = <0 1>;
gpio-req-tbl-flags = <1 0>;
gpio-req-tbl-label = "CAMIF_MCLK0",
"CAM_RESET0";
sensor-mode = <0>;
cci-master = <0>;
status = "ok";
clocks = <&clock_camcc CAM_CC_MCLK0_CLK>;
clock-names = "cam_clk";
clock-cntl-level = "turbo";
clock-rates = <24000000>;
};
qcom,cam-sensor@1 {
cell-index = <1>;
compatible = "qcom,cam-sensor";
reg = <0x1>;
csiphy-sd-index = <1>;
sensor-position-roll = <90>;
sensor-position-pitch = <0>;
sensor-position-yaw = <180>;
eeprom-src = <&eeprom_rear_aux>;
cam_vio-supply = <&camera_vio_ldo>;
cam_vana-supply = <&camera_vana_ldo>;
cam_vdig-supply = <&camera_ldo>;
cam_clk-supply = <&titan_top_gdsc>;
regulator-names = "cam_vdig", "cam_vio", "cam_vana",
"cam_clk";
rgltr-cntrl-support;
rgltr-min-voltage = <1352000 1800000 2850000 0>;
rgltr-max-voltage = <1352000 1800000 2850000 0>;
rgltr-load-current = <105000 0 80000 0>;
gpio-no-mux = <0>;
pinctrl-names = "cam_default", "cam_suspend";
pinctrl-0 = <&cam_sensor_mclk1_active
&cam_sensor_rear2_active>;
pinctrl-1 = <&cam_sensor_mclk1_suspend
&cam_sensor_rear2_suspend>;
gpios = <&tlmm 14 0>,
<&tlmm 28 0>;
gpio-reset = <1>;
gpio-req-tbl-num = <0 1>;
gpio-req-tbl-flags = <1 0>;
gpio-req-tbl-label = "CAMIF_MCLK1",
"CAM_RESET1";
sensor-mode = <0>;
cci-master = <1>;
status = "ok";
clocks = <&clock_camcc CAM_CC_MCLK1_CLK>;
clock-names = "cam_clk";
clock-cntl-level = "turbo";
clock-rates = <24000000>;
};
qcom,cam-sensor@2 {
cell-index = <2>;
compatible = "qcom,cam-sensor";
reg = <0x02>;
csiphy-sd-index = <2>;
sensor-position-roll = <270>;
sensor-position-pitch = <0>;
sensor-position-yaw = <0>;
eeprom-src = <&eeprom_front>;
actuator-src = <&actuator_front>;
led-flash-src = <&led_flash_front>;
cam_vio-supply = <&camera_vio_ldo>;
cam_vana-supply = <&camera_vana_ldo>;
cam_vdig-supply = <&camera_ldo>;
cam_clk-supply = <&titan_top_gdsc>;
regulator-names = "cam_vio", "cam_vana", "cam_vdig",
"cam_clk";
rgltr-cntrl-support;
rgltr-min-voltage = <1800000 2850000 1352000 0>;
rgltr-max-voltage = <1800000 2850000 1352000 0>;
rgltr-load-current = <0 80000 105000 0>;
gpio-no-mux = <0>;
pinctrl-names = "cam_default", "cam_suspend";
pinctrl-0 = <&cam_sensor_mclk2_active
&cam_sensor_front_active>;
pinctrl-1 = <&cam_sensor_mclk2_suspend
&cam_sensor_front_suspend>;
gpios = <&tlmm 15 0>,
<&tlmm 9 0>;
gpio-reset = <1>;
gpio-req-tbl-num = <0 1>;
gpio-req-tbl-flags = <1 0>;
gpio-req-tbl-label = "CAMIF_MCLK2",
"CAM_RESET2";
sensor-mode = <0>;
cci-master = <1>;
status = "ok";
clocks = <&clock_camcc CAM_CC_MCLK2_CLK>;
clock-names = "cam_clk";
clock-cntl-level = "turbo";
clock-rates = <24000000>;
};
};