wl12xx: Add Support for Low Power DRPw (LPD) Mode
The Low Power DRPw (LPD) mode contains several optimizations
that designed to reduce power consumption. The purpose
is to save current consumption in RX and Listen mode.
LPD setting apply only for wl127x AP mode (not wl128x)
Signed-off-by: Shahar Levi <shahar_levi@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
diff --git a/drivers/net/wireless/wl12xx/boot.c b/drivers/net/wireless/wl12xx/boot.c
index 7ccec07..9dcfc6d 100644
--- a/drivers/net/wireless/wl12xx/boot.c
+++ b/drivers/net/wireless/wl12xx/boot.c
@@ -749,6 +749,9 @@
clk |= (wl->ref_clock << 1) << 4;
}
+ if (wl->quirks & WL12XX_QUIRK_LPD_MODE)
+ clk |= SCRATCH_ENABLE_LPD;
+
wl1271_write32(wl, DRPW_SCRATCH_START, clk);
wl1271_set_partition(wl, &part_table[PART_WORK]);
diff --git a/drivers/net/wireless/wl12xx/cmd.c b/drivers/net/wireless/wl12xx/cmd.c
index b3a4f582..cdcb324 100644
--- a/drivers/net/wireless/wl12xx/cmd.c
+++ b/drivers/net/wireless/wl12xx/cmd.c
@@ -134,6 +134,11 @@
/* Override the REF CLK from the NVS with the one from platform data */
gen_parms->general_params.ref_clock = wl->ref_clock;
+ /* LPD mode enable (bits 6-7) in WL1271 AP mode only */
+ if (wl->quirks & WL12XX_QUIRK_LPD_MODE)
+ gen_parms->general_params.general_settings |=
+ GENERAL_SETTINGS_DRPW_LPD;
+
ret = wl1271_cmd_test(wl, gen_parms, sizeof(*gen_parms), answer);
if (ret < 0) {
wl1271_warning("CMD_INI_FILE_GENERAL_PARAM failed");
diff --git a/drivers/net/wireless/wl12xx/ini.h b/drivers/net/wireless/wl12xx/ini.h
index 1420c84..4cf9ecc 100644
--- a/drivers/net/wireless/wl12xx/ini.h
+++ b/drivers/net/wireless/wl12xx/ini.h
@@ -24,6 +24,9 @@
#ifndef __INI_H__
#define __INI_H__
+#define GENERAL_SETTINGS_DRPW_LPD 0xc0
+#define SCRATCH_ENABLE_LPD BIT(25)
+
#define WL1271_INI_MAX_SMART_REFLEX_PARAM 16
struct wl1271_ini_general_params {
diff --git a/drivers/net/wireless/wl12xx/main.c b/drivers/net/wireless/wl12xx/main.c
index f19bf0b..1b55803 100644
--- a/drivers/net/wireless/wl12xx/main.c
+++ b/drivers/net/wireless/wl12xx/main.c
@@ -1191,9 +1191,13 @@
wl1271_debug(DEBUG_BOOT, "chip id 0x%x (1271 PG20)",
wl->chip.id);
- /* end-of-transaction flag should be set in wl127x AP mode */
+ /*
+ * 'end-of-transaction flag' and 'LPD mode flag'
+ * should be set in wl127x AP mode only
+ */
if (wl->bss_type == BSS_TYPE_AP_BSS)
- wl->quirks |= WL12XX_QUIRK_END_OF_TRANSACTION;
+ wl->quirks |= (WL12XX_QUIRK_END_OF_TRANSACTION |
+ WL12XX_QUIRK_LPD_MODE);
ret = wl1271_setup(wl);
if (ret < 0)
@@ -1206,6 +1210,7 @@
ret = wl1271_setup(wl);
if (ret < 0)
goto out;
+
if (wl1271_set_block_size(wl))
wl->quirks |= WL12XX_QUIRK_BLOCKSIZE_ALIGNMENT;
break;
diff --git a/drivers/net/wireless/wl12xx/wl12xx.h b/drivers/net/wireless/wl12xx/wl12xx.h
index 4bc22d8..8d6c8f2 100644
--- a/drivers/net/wireless/wl12xx/wl12xx.h
+++ b/drivers/net/wireless/wl12xx/wl12xx.h
@@ -645,4 +645,10 @@
/* WL128X requires aggregated packets to be aligned to the SDIO block size */
#define WL12XX_QUIRK_BLOCKSIZE_ALIGNMENT BIT(2)
+/*
+ * WL127X AP mode requires Low Power DRPw (LPD) enable to reduce power
+ * consumption
+ */
+#define WL12XX_QUIRK_LPD_MODE BIT(3)
+
#endif